ARRIS WE800G User Manual
User Guide
Wireless Ethernet
Bridge
WE800G
MOTOROLA INC. declares that WE800g ( FCC ID: ACQWE800G ) is limited in CH1~
CH11 by specified firmware controlled in U.S.A.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. THE UNIT MUST NOT BE
EXPOSED TO DRIPPING OR SPLASHING. DO NOT PLACE OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, ON THE UNIT.
CAUTION: TO ENSURE REGULATORY COMPLIANCE, USE ONLY THE PROVIDED POWER AND INTERFACE CABLES.
CAUTION: DO NOT OPEN THE UNIT. DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE INSTALLATION AND
TROUBLESHOOTING INSTRUCTIONS. REFER ALL SERVICING TO QUALIFIED SERVICE PERSONNEL.
This device must be installed and used in strict accordance with the manufacturer’s instructions as described in the user documentation that comes with the
product.
Postpone router installation until there is no risk of thunderstorm or lightning activity in the are a.
Do not overload outlets or extension cords, as this can result in a risk of fire or electric shock. Overloaded AC outlets, extension cords, frayed power cords,
damaged or cracked wire insulation, and broken plugs are dangerous. They may result in a shock or fire hazard.
Route power supply cords so that they are not likely to be walked on or pinched by items placed upon or against them. Pay particular attention to cords where
they are attached to plugs and convenience receptacles, and examine the point where they exit from the product.
Place this equipment in a location that is close enough to an electrical outlet to accommodate the length of the power cord.
Place this equipment on a stable surface.
When using this device, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the
following:
• Read all of the instructions {listed here and/or in the user manual} before you operate this equipment. Give particular attention to all safety precautions.
Retain the instructions for future reference.
• Comply with all warning and caution statements in the instructions. Observe all warning and caution symbols that are affixed to this equipment.
• Comply with all instructions that accompany this equipment.
• Avoid using this product during an electrical storm. There may be a risk of electric shock from lightning. For added protection for this product during a
lightning storm, or when it is left unattended and unus ed for long periods of time, unplug it from the wall outlet, and disconnect the cable system. This will
prevent damage to the product due to lightning and power surges.
• Operate this product only from the type of power source indicated on the product’s marking label. If you are not sure of the type of power supplied to your
home, consult your dealer or local power company.
• Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in safe
operating condition.
It is recommended that the customer install an AC surge protector in the AC outlet to which this device is connected. This is to avoid damaging the equipment by
local lightning strikes and other electrical surges.
Different types of cord sets may be used for connections to the main supply circuit. Use only a main line cord that complies with all applicable product safety
requirements of the country of use.
Installation of this product must be in accordance with national wiring codes.
Place unit to allow for easy access when disconnecting the power cord/adapter of the device from the AC wall outlet.
Wipe the unit with a clean, dry cloth. Never use cleaning fluid or similar chemicals. Do not spray cleaners directly on the unit or use forced air to remove dust.
This product was qualified under test conditions that included the use of the supplied cables between system components. To be in compliance with regulations,
the user must use these cables and install them properly. Connect the unit to a grounding type AC wall outlet using the power adapter supplied with the unit.
Do not cover the device, or block the airflow to the device with any other objects. Keep the device away from excessive heat and humidity and keep the device
free from vibration and dust.
Installation must at all times conform to local regulations.
FCC Compliance Class B Digital Device
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, the re is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interfere nce to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modifications not expressly approved by Motorola for compliance could void the user’s authority to operate the equipment.
The antennas used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure
compliance.
Canadian Compliance
This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Cet appareil numérique de la classe B
respe cts tout es les e xigences d u Règlement s ur le matérie l brouilleur du Canada.
FCC Declaration of Conformity
Motorola, Inc., Broadband Communications Sector, 101 Tournament Drive, Horsham, PA 19044, 1-215-323-1000, declares under sole responsibility tha t the
WR850G, WE800G, WA840G, WN825G, WPCI810G, and BR700 compile with 47 CFR Parts 2 and 15 of the FCC Rules as a Class B digital device. This
device complies with Part 15 of FCC Rules. Operation of the device is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference that may cause undesired operation.
Wireless LAN Information
The WR850G, WE800G, WA840G, WN825G, and WPCI810G Wireless LAN products are wireless network products that uses Direct Sequence Spread
Spectrum (DSSS) radio technology. This product is designed to be inter-operable with any other wireless DSSS type product that complies with:
• The IEEE 802.11 Standard on Wireless LANs (Revision B), as defined and approved by the Institute of Electrical Electronics Engineers.
• The Wireless Fid elity (WiFi) c ertification as de fined by the Wireless Ethernet Compatibility Alliance (W ECA).
Wireless LAN and your Health
The WR850G, WE800G, WA840G, WN825G, and WPCI810G, like other radio devices, emits radio frequency electromagnetic energy, but operates within the
guidelines fo und in radio fre quency safety standards and recommendat ions.
Restrictions on Use of Wireless Devices
In some situations or environments, the use of wireless devices may be restricted by the proprietor of the building or responsible representatives of the
organization. For example, these situations may include:
• Using wireless equipment on board an airplane.
• Using wireless equipment in any environment where the risk of interference to other devices or services is perceived or identified as harmful.
If you are uncertain of the applicable policy for the use of wireless equipment in a specific organization or environment (such as airports), you are encouraged to
ask for authorization to use the device prior to turning on the equipment.
The manufacturer is not responsible for any radio or television interference caused by unauthorized modification of the devices included with this product, or the
substitution or attachment of connecting cables and equipment other than specified by the manufacturer. Correction of interference caused by such unauthorized
modificatio n, subst it u tion, or a t tachment is the resp onsibility of the user.
The manufacturer and its authoriz ed rese llers or distributor s are not liable for any damage or violation of government regulations that may arise from failing to
comply with these guidelines.
FCC Certification
The WR850G, WE800G, WA840G, WN825G, and WPCI810G contains a radio transmitter and accordingly has
been certified as compliant with 47 CFR Part 15 of the FCC Rules for intentional radiators. Products that contain a
radio transmitter are labeled with FCC ID and the FCC logo.
Caution: Exposure t o Radio Frequency Radiation.
Canada - Industry Canada (IC)
The wireless radio of this device complies with RSS 210 ans RSS 102 of Industry Canada.
This Class B digitral device complies with Canadian ICES-003 (NMB-003).
Cet appareil numérique de la classe B respects toutes les exigences du Règlement sur le matériel brouilleur du Canada
Copyright © 2003 by Motorola, Inc.
All rights reserved. No part of this publication may be reproduced in any form or by any means or used to make any derivative work (such as
translation, transformation or adaptation) without written permission from Motorola, Inc.
Motorola reserves the right to revise this publication and to make changes in content from time to time without obligation on the part of Motorola to
provide notification of such revision or change. Motorola provides this guide without warranty of any kind, either implied or expressed, including,
but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Motorola may make improvements or changes in
the product(s) described in this manual at any time.
MOTOROLA and the Stylized M Logo are registered in the US Patent & Trademark Office. Microsoft Windows screen shots are used by
permission of Microsoft Corporation. All other product or service names are the property of their respective owners. © Motorola, Inc. 2003
Contents
Section 1:Overview _______________________ 1-1
Features ................................................................................................................ 1-2
Understanding your User Guide ......................................................................... 1-2
Box Contents ........................................................................................................ 1-3
Understanding Functions .................................................................................... 1-3
Wireless Ethernet Bridge Connectivity................................................................1-3
TCP/IP.................................................................................................................1-4
Static IP Address...........................................................................................................1-4
Dynamic IP Address......................................................................................................1-4
Understanding Wireless ................................................................................................1-4
Wireless Range...................................................................................................1-5
Recommended Wireless Environment ................................................................1-5
Type of Networks.................................................................................................. 1-6
Wireless Ethernet Bridge Infrastructure Mode.....................................................1-6
Wireless Ethernet Bridge Ad-Hoc Mode..............................................................1-7
Multiple Clients Mode..........................................................................................1-8
Wireless Ethernet Bridge Physical Description................................................. 1-9
Back of Wireless Ethernet Bridge........................................................................1-9
Front of Wireless Ethernet Bridge .....................................................................1-11
LED Description ................................................................................................1-12
Section 2:Installation______________________ 2-1
Hardware Setup .................................................................................................... 2-1
Antenna Installation.............................................................................................2-1
Wireless Ethernet Bridge Physical Installation ....................................................2-2
Horizontal Installation ....................................................................................................2-2
Vertical Installation ........................................................................................................2-3
Wall Mount Installation ..................................................................................................2-3
Electrical Connection to Wireless Ethernet Bridge ..............................................2-6
Easy Software Setup ............................................................................................ 2-7
Manual Software Setup........................................................................................ 2-7
Wired Connection to Wireless Ethernet Bridge ...................................................2-8
Configure Your Computers.................................................................................. 2-9
Configuring Windows 98SE and ME .................................................................2-10
Windows 98 and ME DHCP Server Configuration ......................................................2-12
Configuring Windows 2000 ...............................................................................2-12
Windows 2000 DHCP Server Configuration................................................................2-15
Configuring Windows XP...................................................................................2-15
Windows XP DHCP Server Configuration...................................................................2-18
Configure Your Wireless Security Settings...................................................... 2-19
Logging In .........................................................................................................2-19
Wireless Security Setup ....................................................................................2-20
CONTENTS I
CONTENTS
Section 3:Configuration ___________________ 3-1
Using the Web-Based Configuration Utility ........................................................3-1
Logging In ...........................................................................................................3-1
Navigation ...........................................................................................................3-2
Help, Restart, and Log Out .................................................................................3-2
Active Profile and Site Monitor ............................................................................3-3
Site Survey – Active Profile.................................................................................3-3
Site Survey – Site Monitor...................................................................................3-4
Configuring Wireless Profile 1 or 2......................................................................3-5
Wireless – Basic..................................................................................................3-5
Wireless – Security .............................................................................................3-6
Wireless – Advanced ........................................................................................3-10
Wireless – Professional.....................................................................................3-11
Configuring Control Panel Settings...................................................................3-13
Control Panel – Network Address.....................................................................3-13
Control Panel – Device Security........................................................................3-14
Control Panel – Firmware Update.....................................................................3-15
Control Panel – Configuration Data...................................................................3-16
Section 4:Troubleshooting _________________ 4-1
Contact Us ..........................................................................................................4-1
Hardware Solutions...............................................................................................4-1
Software Solutions................................................................................................4-3
I cannot access the Configuration Utility for the unit. ....................................................4-3
My WE800G cannot associate with the wireless access point/router ...........................4-4
I would like to see if my Internet connection is alive......................................................4-4
Section 5:Glossary _______________________ 5-1
=
II CONTENTS
Section 1:Overview
Congratulations on purchasing the Motorola Wireless Ethernet Bridge
WE800G. With this unit, you have entered the world of freedom and
independence – freedom from wires and the independence to
communicate wherever YOU choose.
The WE800G is built with both the popular 802.11b wireless standard
and the new nearly 5-times-faster 802.11g standard, providing you
the ultimate in flexibility and speed. With Wired Equivalent Privacy
(WEP) supported, your wireless connections are robust and secure,
giving you the security to communicate without fear that your signal
might be compromised.
Upgradeable firmware keeps the Wireless Ethernet Bridge control
software up-to-date. The WE800G captures the latest technology in a
package that stays current, connects multiple products to your home
network, and provides you easy home network management.
Wireless Ethernet Bridge WE800G
SECTION 1, OVERVIEW 1-1
SECTION 1 OVERVIEW
Features
The WE800G has the following features:
! Wirelessly connects separate wireless networks together
! Connect any Ethernet equipped device to your wireless network;
for example, a gaming console, a laptop or desktop computer, or
a printer
! Compatibility with both 802.11g and 802.11b standards
! CD-ROM based Installation Wizard for easy installation
! Built-in Web interface for easy configuration
! Firmware upgrade to stay current with latest specification
Your Motorola WE800G Wireless Ethernet Bridge enables you to
extend your wireless network and increase your productivity.
Understanding your User Guide
The User Guide is subdivided into the following sections:
Overview Provides a general introduction for using your
product, the type of technology used, and
recommended practices for using it.
Installation It is assumed that you will use the Installation
Wizard on the CD-ROM to setup your unit. If not,
then refer to this section for details on getting your
unit up and running.
Once you have completed this section, your unit
will be active and ready to work.
Configuration Provides descriptive details for using the
web-based Configuration Utility to manage your
unit.
Glossary Defines the terms and acronyms.
1-2 SECTION 1, OVERVIEW
OVERVIEW SECTION 1
Box Contents
Your box contains the following:
CD-ROM
Power
Adapter
Antenna
Power
Cord
Ethernet
Cable
Base Station Stand
WE800G
Quick Start
Guide
Understanding Functions
The various technologies and features used by your Wireless
Ethernet Bridge require some conceptual explanation so that you can
make the correct choices when configuring your unit.
Wireless Ethernet Bridge Connectivity
Your unit wirelessly connects:
! Networks or units to a network, Or
! By configuring multiple clients such as laptops, each using their
own Wireless Ethernet Bridge, are you able to create your own
private wireless Ad-Hoc network
The mechanics behind the connectivity are explained in the following
subsections.
SECTION 1, OVERVIEW 1-3
SECTION 1 OVERVIEW
TCP/IP
Transmission Control Protocol/Internet Protocol (TCP/IP) comprises
the backbone of the Internet. IP moves packets of data between
nodes while TCP verifies delivery from client to server. Every device
you hook up to your wireless router identifies itself with an IP
address. You are able to assign devices on your network with either
a static or dynamically assigned IP address.
Static IP Address
A static IP address is a fixed address that is assigned manually to a
device on the network. Static IP addresses must be unique and
cannot be shared, therefore they are used in situations where the
address should never change, like print servers or PC servers.
Dynamic IP Address
A dynamic IP address is a temporary IP address, dynamically or
randomly generated by a DHCP server. The address lasts only as
long as the server specifies, usually in the space of a day or two.
When the IP address expires, the client is automatically reassigned a
new IP address, ensuring smooth communication.
Understanding Wireless
Your Wireless Ethernet Bridge uses a radio transmission technology
defined by the Institute of Electrical and Electronics Engineers (IEEE)
called 802.11 or Wi-Fi (Wireless Fidelity). This 802.11 standard is
subdivided into distinct categories of speed and the frequency
spectrum used, designated by the lower case letter after the
standard.
For example, your Wireless Ethernet Bridge supports both the ‘b’ and
‘g’ specifications. The 802.11b standard specifies transmission rates
up to 11 Mbps while the 802.11g standard specifies transmission
rates up to 54 Mbps. The radio waves radiate out in a donut-shaped
pattern. The waves travel through walls and floors, but transmission
power and distance are affected. The theoretical distance limit is
1,000 feet (305 meters), but actual throughput and distance varies.
Both the 802.11b and 802.11g standards operate in the 2.4 GHz
range, meaning other electrical appliances also might interfere with
the Wireless Ethernet Bridge – televisions, radios, microwave ovens,
and 2.4 GHz cordless telephones. Therefore, positioning your
Wireless Ethernet Bridge where it encounters the least interference
gains the greatest benefit to maintaining a quality connection.
1-4 SECTION 1, OVERVIEW
OVERVIEW SECTION 1
Wireless Range
The following describes different scenarios for the expected range of
the coverage area of the unit. This table is only a guide and coverage
varies due to local conditions.
Data Rate Open Area Closed Area
54 Mbps Up to 100 ft (30m) Up to 60 ft (18m)
11 Mbps Up to 900 feet (275 m) Up to 160 feet (49 m)
5.5 Mbps Up to 1300 feet (396 m) Up to 200 feet (61 m)
2 or 1 Mbps Up to 1500 feet (457 m) Up to 300 feet (91 m)
Recommended Wireless Environment
The following information helps you to achieve the best wireless
performance:
! Placing your Wireless Ethernet Bridge in the physical center of
your network is the premium location because the antenna
radiates out the signal in all directions.
! Placing the unit in a higher location, such as atop a cabinet, helps
to disperse the signal cleanly, especially to receiving locations on
upper stories.
! Direct line of sight achieves better performance, but obviously is
not always achievable.
! Try to avoid placing the unit next to large solid objects like
computer cases, monitors, walls, fireplaces, etc. This helps the
signal penetrate more cleanly.
! Other wireless devices like televisions, radios, microwaves and
2.4 GHz cordless telephones can interfere with the signal. Keep
devices away from the unit.
SECTION 1, OVERVIEW 1-5
SECTION 1 OVERVIEW
Type of Networks
Your Wireless Ethernet Bridge supports several different usage
scenarios and the following examples illustrate the flexibility of your
WE800G. Some scenarios require additional hardware.
Wireless Ethernet Bridge Infrastructure Mode
In this mode, the WE800G functions like a bridge, connecting wired
Ethernet clients to a wireless network. This is the most likely scenario
you will use, because it shares an Internet connection with your
laptop or other wireless client.
1-6 SECTION 1, OVERVIEW
OVERVIEW SECTION 1
Wireless Ethernet Bridge Ad-Hoc Mode
This mode is very similar to the Wireless Ethernet Bridge
Infrastructure mode, except the WE800G will connect to other client
devices using Ad-Hoc mode. One inherent limitation of operating in
this mode is that all client devices must be in wireless range of each
other, as opposed to a network with an Access Point, where all
wireless devices must be in range of the Access Point.
SECTION 1, OVERVIEW 1-7
SECTION 1 OVERVIEW
Multiple Clients Mode
In this mode, the WE800G connects multiple clients to your network
wirelessly.
1-8 SECTION 1, OVERVIEW
OVERVIEW SECTION 1
A
A
Wireless Ethernet Bridge Physical Description
The following sections describe the physical characteristics of the
WE800G.
Back of Wireless Ethernet Bridge
The following illustration shows the WE800G back panel:
-
+
Power
Receptacle
LAN
Port
Reset
Reset
Button
ntennaLANPower
ntenna
Feature Description
Power
Receptacle
The receptacle used to plug in the power adapter.
LAN Port The receptacle used to plug in an Ethernet cable.
SECTION 1, OVERVIEW 1-9
SECTION 1 OVERVIEW
Feature Description
Reset
Button
A dual-function button. It either resets your unit or
resets the unit to the default login settings.
If the Wireless Ethernet Bridge is experiencing
trouble connecting to the Internet, briefly press and
release the Reset button to reset the router. This
retains the router’s configuration information.
To reset the unit to the factory defaults while the unit
is powered up, press and hold the Reset button for
more than five seconds. This clears the Wireless
Ethernet Bridge’s user settings, including User ID,
Password, IP Address, and Subnet mask. Refer to
Section 3: Configuration to re-configure the unit.
Antenna The antenna used for wireless connections. You are
able to rotate and tilt the antenna to gain the best
signal reception.
1-10 SECTION 1, OVERVIEW
OVERVIEW SECTION 1
Front of Wireless Ethernet Bridge
The following illustration shows the WE800G front panel:
r
e
w
o
P
s
s
e
e
l
e
r
i
W
c
i
v
e
D
1. 2. 3.
The LEDs of the unit indicate its operational status.
SECTION 1, OVERVIEW 1-11
SECTION 1 OVERVIEW
LED Description
The underlined items represent network activity.
LED Condition Color Status
1. Power ON
Blinking
Blinking/ON
Green
Green
Red
The device is powered on and operating normally.
Firmware update is in progress.
The power LED turns red as soon as the reset button
is depressed.
If the reset button is held down for more than five
seconds, the LED starts to blink, during which time
the Wireless Ethernet Bridge’s default user name,
password, and IP address will be restored. The LED
then turns off until the reset button is released.
The power LED keeps blinking red if the firmware is
corrupted, indicating the firmware needs to be
restored.
2. Wireless OFF
None
No mobile station or AP has associated with this
device.
ON
Red
The wireless interface has been disabled by the
firmware.
ON/Blinking
Connection exists in this wireless domain/active
Green
traffic present.
3. Device OFF
None
No external Ethernet device has been attached and
detected. The Ethernet link is down.
ON/Blinking
ON/Blinking
Green
10BaseT link detected/active traffic present.
100BaseT link detected/active traffic present.
Amber
1-12 SECTION 1, OVERVIEW
Section 2:Installation
To get your network up and running:
1 Setup your hardware.
CAUTION!
2 Insert the CD-ROM for Software Setup. Follow the prompts.
If you prefer to setup the Wireless Ethernet Bridge software
manually, refer to the Manual Software Setup found in this section.
The following sections provide detailed instructions for completing
these tasks.
Hardware Setup
Hardware setup includes:
! Antenna Installation: connecting the antenna to the unit.
Use only the Motorola supplied WE800G power adapter.
! Physical Installation: where you physically place your unit.
! Electrical Connection: how to power your unit.
Antenna Installation
When shipped, the antenna is already installed on the main unit. If,
for some reason, you have to detach and than re-attach the antenna
to the main unit:
1 Take the bottom of the antenna and locate, on the right backside
of the Wireless Ethernet Bridge, the threaded knob.
2 Screw the antenna connector (counter-clockwise to remove,
clockwise to attach) on to the threaded knob until firmly seated.
When attaching, do not over-tighten.
SECTION 2, INSTALLATION 2-1
SECTION 2 INSTALLATION
Wireless Ethernet Bridge Physical Installation
You can install the Wireless Ethernet Bridge in different physical
orientations – horizontally, vertically, or hung on the wall. Your own
needs determine the best placement.
Horizontal Installation
To install the Wireless Ethernet Bridge horizontally, as shown in the
illustration below:
1 Place the Wireless Ethernet Bridge in the desired location.
2 Follow the procedures in “Electrical Connection to Wireless
Ethernet Bridge” located later in this section to connect the unit.
2-2 SECTION 2, INSTALLATION
INSTALLATION SECTION 2
Vertical Installation
To install the Wireless Ethernet Bridge vertically, as shown in the
illustration below:
1 Insert the Wireless Ethernet Bridge into the supplied base.
Ensure that the antenna’s location is on top, because the antenna
prevents the unit from fitting into the base. The Wireless Ethernet
Bridge’s foot slides snugly into the base to keep the unit stable.
2 Follow the procedures in “Electrical Connection to Wireless
Ethernet Bridge” located later in this section to connect the unit.
Wall Mount Installation
To mount the Wireless Ethernet Bridge on the wall, you must:
! Locate the unit as specified by the local or national codes
governing residential or business communications services.
! Follow all local standards for installing a network interface
unit/network interface device (NIU/NID).
SECTION 2, INSTALLATION 2-3
SECTION 2 INSTALLATION
If possible, mount the Wireless Ethernet Bridge to concrete,
masonry, a wooden stud, or other solid wall material. Use
anchors if necessary; for example if you must mount the unit on
drywall. Mounting the unit on the wall may decrease performance.
To mount your Wireless Ethernet Bridge on the wall:
1 Print the Wall Mounting Template.
3.15
[80.00]
MODE L WE800 G
INPUT VOLTAGE: +5VDC, 2A
FCC ID: F2NWE800G
MODEL: WE800G
Tested To Comply
With FCC Standards
FOR HOME OR OFF ICE USE
PART NUMBER: AAAAAA-BBB-CC
S/N: PPPPMMYJJJSSSSSC AABBCCCC
WIRELESS MAC: AB CD EF 01 23 45
MADE IN TAIWAN
The illustration is drawn at a one-to-one scale, which means that
when printed, it provides the exact dimensions required to mount
the unit.
2 Click the Print icon or choose Print from the File menu to display
the Print dialog box. (A sample print dialog appears below.)
Be sure you print the template at 100% scale and that Fit to page is
not checked in the Print dialog box.
2-4 SECTION 2, INSTALLATION
INSTALLATION SECTION 2
3 Click OK to print the template.
4 Measure the printed template with a ruler to ensure that it is the
correct size.
5 Use a center punch to mark the center of the holes on the wall.
6 On the wall, locate the marks for the mounting holes you just
made.
WARNING!
Before drilling holes, check the structure for potential
damage to water, gas, or electric lines.
7 Drill the holes to a depth of at least 3.8 cm (1½ inches).
8 If necessary, seat an anchor in each hole. Use M5 x 38 mm
(#10-16 x 1½ inch) screws with a flat underside and maximum
screw head diameter of 10.5 mm to mount the unit.
9 Using a screwdriver, turn each screw until part of it protrudes
from the wall, as shown:
! There must be 4.0 mm (.16 inches) between the wall and the
underside of the screw head.
! The maximum distance from the wall to the top of the screw
head is 7.6 mm (.3 in).
7.6 mm (.3 inches)
maximum
10.5 mm (.4 inches)
maximum
4.0 mm
10 Remove the front two plastic feet, nearest to the LED panel, from
the bottom of the unit to uncover the keyholes.
11 Place the unit so the keyholes are above the mounting screws.
12 Slide the Wireless Ethernet Bridge down until it stops against the
top of the keyhole opening.
13 Follow the procedures in “Electrical Connection to Wireless
Ethernet Bridge” located later in this section to connect the unit.
SECTION 2, INSTALLATION 2-5
Loading...