Allied Telesis AT-G8LX User Manual
*613-50515-00 Rev B*
613-50515-00 Rev B
*613-50515-00 Rev B*
613-50515-00 Rev B
*613-50515-00 Rev B*
613-50515-00 Rev B
*613-50515-00 Rev B*
613-50515-00 Rev B
AT-G8LX Series GBIC Transceivers
Installation Guide
Overview
The AT-G8LX Series GBIC Transceivers provide 1000Base-LX
connectivity over single-mode fiber optic cable for Allied Telesis
networking products.
Verifying Package Contents
Ensure that the correct component and installation instructions are
included in your package. If any item is missing or damaged, contact
your Allied Telesis sales representative for assistance.
Cabling Specifications
Model
AT-G8LX10 10 km 9/125 µm Single-Mode Fiber
AT-G8LX25 25 km 9/125 µm Single-Mode Fiber
AT-G8LX40 40 km 9/125 µm Single-Mode Fiber
AT-G8LX70 70 km 9/125 µm Single-Mode Fiber
Maximum
Distance
Type of Fiber Optic
Cable
AT-G8LX Series GBIC Transceivers
Installation Guide
Overview
The AT-G8LX Series GBIC Transceivers provide 1000Base-LX
connectivity over single-mode fiber optic cable for Allied Telesis
networking products.
Verifying Package Contents
Ensure that the correct component and installation instructions are
included in your package. If any item is missing or damaged, contact
your Allied Telesis sales representative for assistance.
Cabling Specifications
Model
AT-G8LX10 10 km 9/125 µm Single-Mode Fiber
AT-G8LX25 25 km 9/125 µm Single-Mode Fiber
AT-G8LX40 40 km 9/125 µm Single-Mode Fiber
AT-G8LX70 70 km 9/125 µm Single-Mode Fiber
Maximum
Distance
Type of Fiber Optic
Cable
AT-G8LX Series GBIC Transceivers
Installation Guide
Overview
The AT-G8LX Series GBIC Transceivers provide 1000Base-LX
connectivity over single-mode fiber optic cable for Allied Telesis
networking products.
Verifying Package Contents
Ensure that the correct component and installation instructions are
included in your package. If any item is missing or damaged, contact
your Allied Telesis sales representative for assistance.
Cabling Specifications
Model
AT-G8LX10 10 km 9/125 µm Single-Mode Fiber
AT-G8LX25 25 km 9/125 µm Single-Mode Fiber
AT-G8LX40 40 km 9/125 µm Single-Mode Fiber
AT-G8LX70 70 km 9/125 µm Single-Mode Fiber
Maximum
Distance
Type of Fiber Optic
Cable
AT-G8LX Series GBIC Transceivers
Installation Guide
Overview
The AT-G8LX Series GBIC Transceivers provide 1000Base-LX
connectivity over single-mode fiber optic cable for Allied Telesis
networking products.
Verifying Package Contents
Ensure that the correct component and installation instructions are
included in your package. If any item is missing or damaged, contact
your Allied Telesis sales representative for assistance.
Cabling Specifications
Model
AT-G8LX10 10 km 9/125 µm Single-Mode Fiber
AT-G8LX25 25 km 9/125 µm Single-Mode Fiber
AT-G8LX40 40 km 9/125 µm Single-Mode Fiber
AT-G8LX70 70 km 9/125 µm Single-Mode Fiber
Maximum
Distance
Type of Fiber Optic
Cable
Fiber Optic Port Specifications
Optical Output
ave-
Model
AT-G8LX10 1310 -9.0 - -3.0 -20.0 -3.0
AT-G8LX25 1310 -4.0 - 1.0 -21.0 -3.0
AT-G8LX40 1550 -4.0 - 1.0 -21.0 -3.0
AT-G8LX70 1550 -3.0 - 2.0 -23.0 -3.0
W
length
Power
(dBm)
Min. Avg. Max. Min. Max.
Optical Input
Power (dBm)
Fiber Optic Port Specifications
Optical Output
ave-
Model
AT-G8LX10 1310 -9.0 - -3.0 -20.0 -3.0
AT-G8LX25 1310 -4.0 - 1.0 -21.0 -3.0
AT-G8LX40 1550 -4.0 - 1.0 -21.0 -3.0
AT-G8LX70 1550 -3.0 - 2.0 -23.0 -3.0
|
W
length
Power
(dBm)
Min. Avg. Max. Min. Max.
Optical Input
Power (dBm)
Fiber Optic Port Specifications
Optical Output
ave-
Model
AT-G8LX10 1310 -9.0 - -3.0 -20.0 -3.0
AT-G8LX25 1310 -4.0 - 1.0 -21.0 -3.0
AT-G8LX40 1550 -4.0 - 1.0 -21.0 -3.0
AT-G8LX70 1550 -3.0 - 2.0 -23.0 -3.0
|
W
length
Power
(dBm)
Min. Avg. Max. Min. Max.
Optical Input
Power (dBm)
Fiber Optic Port Specifications
Optical Output
ave-
Model
AT-G8LX10 1310 -9.0 - -3.0 -20.0 -3.0
AT-G8LX25 1310 -4.0 - 1.0 -21.0 -3.0
AT-G8LX40 1550 -4.0 - 1.0 -21.0 -3.0
AT-G8LX70 1550 -3.0 - 2.0 -23.0 -3.0
|
W
length
Power
(dBm)
Min. Avg. Max. Min. Max.
Optical Input
Power (dBm)
Laser
Class 1 laser product. Do not stare into the laser beam.
Laser
Class 1 laser product. Do not stare into the laser beam.
Laser
Class 1 laser product. Do not stare into the laser beam.
Laser
Class 1 laser product. Do not stare into the laser beam.
Note
A transceiver must be connected to another transceiver or fiber
optic port that has similar operating characteristics.
Note
The AT-G8LX Series GBIC Transceivers can be hot-swapped.
You do not need to power off the networking device when
installing or replacing a GBIC transceiver.
Installing an AT-G8LX Series GBIC Transceiver
To install an AT-G8LX Series GBIC Transceiver, perform the following
procedure:
1. Remove the transceiver from the shipping package.
Caution
The transceiver can be damaged by static electricity. Be sure to
observe all standard electrostatic discharge (ESD) precautions.
2. Slide the transceiver into the GBIC slot on the Allied Telesis networking device.
3. Remove the dust cover from the dual SC connector on the GBIC module.
4. Connect the fiber optic data cables to the dual SC connector on the module.
Note
When connecting fiber optic cables to a GBIC module, be sure
that the cable connected to the RX (receive) port on the GBIC
is connected to the transmitter port on the remote fiber optic
port, and that the TX (transmit) port is connected to the receiver
port on the remote fiber optic port.
For information on the transceiver port LEDs, refer to the
appropriate installation guide.
Note
A transceiver must be connected to another transceiver or fiber
optic port that has similar operating characteristics.
Note
The AT-G8LX Series GBIC Transceivers can be hot-swapped.
You do not need to power off the networking device when
installing or replacing a GBIC transceiver.
Installing an AT-G8LX Series GBIC Transceiver
To install an AT-G8LX Series GBIC Transceiver, perform the following
procedure:
1. Remove the transceiver from the shipping package.
Caution
The transceiver can be damaged by static electricity. Be sure to
observe all standard electrostatic discharge (ESD) precautions.
2. Slide the transceiver into the GBIC slot on the Allied Telesis networking device.
3. Remove the dust cover from the dual SC connector on the GBIC module.
4. Connect the fiber optic data cables to the dual SC connector on the module.
Note
When connecting fiber optic cables to a GBIC module, be sure
that the cable connected to the RX (receive) port on the GBIC
is connected to the transmitter port on the remote fiber optic
port, and that the TX (transmit) port is connected to the receiver
port on the remote fiber optic port.
For information on the transceiver port LEDs, refer to the
appropriate installation guide.
Note
A transceiver must be connected to another transceiver or fiber
optic port that has similar operating characteristics.
Note
The AT-G8LX Series GBIC Transceivers can be hot-swapped.
You do not need to power off the networking device when
installing or replacing a GBIC transceiver.
Installing an AT-G8LX Series GBIC Transceiver
To install an AT-G8LX Series GBIC Transceiver, perform the following
procedure:
1. Remove the transceiver from the shipping package.
Caution
The transceiver can be damaged by static electricity. Be sure to
observe all standard electrostatic discharge (ESD) precautions.
2. Slide the transceiver into the GBIC slot on the Allied Telesis networking device.
3. Remove the dust cover from the dual SC connector on the GBIC module.
4. Connect the fiber optic data cables to the dual SC connector on the module.
Note
When connecting fiber optic cables to a GBIC module, be sure
that the cable connected to the RX (receive) port on the GBIC
is connected to the transmitter port on the remote fiber optic
port, and that the TX (transmit) port is connected to the
receiver port on the remote fiber optic port.
For information on the transceiver port LEDs, refer to the
appropriate installation guide.
Note
A transceiver must be connected to another transceiver or fiber
optic port that has similar operating characteristics.
Note
The AT-G8LX Series GBIC Transceivers can be hot-swapped.
You do not need to power off the networking device when
installing or replacing a GBIC transceiver.
Installing an AT-G8LX Series GBIC Transceiver
To install an AT-G8LX Series GBIC Transceiver, perform the following
procedure:
1. Remove the transceiver from the shipping package.
Caution
The transceiver can be damaged by static electricity. Be sure to
observe all standard electrostatic discharge (ESD) precautions.
2. Slide the transceiver into the GBIC slot on the Allied Telesis networking device.
3. Remove the dust cover from the dual SC connector on the GBIC module.
4. Connect the fiber optic data cables to the dual SC connector on the module.
Note
When connecting fiber optic cables to a GBIC module, be sure
that the cable connected to the RX (receive) port on the GBIC
is connected to the transmitter port on the remote fiber optic
port, and that the TX (transmit) port is connected to the
receiver port on the remote fiber optic port.
For information on the transceiver port LEDs, refer to the
appropriate installation guide.
This product meets the following standards.
U.S. Federal Communications Commission
Radiated Energy
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radi ate radio frequency energy and, if not installed
and used in accordance with this instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
Note: Modifications or changes not expressly approved of by the man ufacturer
or the FCC, can void your righ t to operate this equipment.
Industry Canada
This Class A digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du
Règlement sur le matériel brouilleur du Canada.
RFI Emissions: FCC Class A, EN 55022 Class A, VCCI Class A
Immunity: EN 55024
Electrical Safety: UL 60950-1 (
), EN 60950-1, EN 60825
cULus
This product meets the following standards.
U.S. Federal Communications Commission
Radiated Energy
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with this instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
Note: Modifications or changes not expressly approved of by the manufacturer
or the FCC, can void your right to operate this equipment.
Industry Canada
This Class A digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du
Règlement sur le matériel brouilleur du Canada.
RFI Emissions: FCC Class A, EN 55022 Class A, VCCI Class A
Immunity: EN 55024
Electrical Safety: UL 60950-1 (
), EN 60950-1, EN 60825
cULus
This product meets the following standards.
U.S. Federal Communications Commission
Radiated Energy
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with this instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interferen ce in which case the user will
be required to correct the interference at his own expense.
Note: Modifications or changes not expressly approved of by the manufacturer
or the FCC, can void your righ t to operate this equipment.
Industry Canada
This Class A digital apparatus meets all requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du
Règlement sur le matériel brouilleur du Canada.
RFI Emissions: FCC Class A, EN 55022 Class A, VCCI Class A
Immunity: EN 55024
Electrical Safety: UL 60950-1 (
), EN 60950-1, EN 60825
cULus
This product meets the following standards.
U.S. Federal Communications Commission
Radiated Energy
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with this instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in wh ich case the user will
be required to correct the interference at his own expense.
Note: Modifications or changes not expressly approved of by the manufacturer
or the FCC, can void your right to operate this equipment.
Industry Canada
This Class A digital apparatus meets al l requirements of the Canadian
Interference-Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du
Règlement sur le matériel brouilleur du Canada.
RFI Emissions: FCC Class A, EN 55022 Class A, VCCI Class A
Immunity: EN 55024
Electrical Safety: UL 60950-1 (
), EN 60950-1, EN 60825
cULus
Loading...