Allied Telesis AT-FS909SX User Manual

AT-FS909SX

Fast Ethernet Switch

Installation Guide

PN 613-10846-00 Rev A

Copyright 2000 Allied Telesyn International, Corp.

960 Stewart Drive Suite B, Sunnyvale CA 94086 USA
All rights reserved. No part of this publication may be reproduced without prior written permission

from Allied Telesyn International, Corp.
Ethernet is a registered trademark of Xerox Corporation. All other product names, company names,

logos or other designations mentioned herein are trademarks or registered trademarks of their
respective owners.

Allied Telesyn International Corp. reserves the right to make changes in specifications and other
information contained in this document without prior written notice. The information provided
herein is subject to change without notice. In no event shall Allied Telesyn be liable for any incidental,
special, indirect, or consequential damages whatsoever, including but not limited to lost profits,
arising out of or related to this manual or the information contained herein, even if Allied Telesyn
International Corp. has been advised of, known, or should have known, the possibility of such
damages.

Electrical Safety and Emission Compliance Statement

Standards: This product meets the following standards

U.S. Federal Communications Commission

RADIATED ENERGY
Note: This equipment has bee n test ed and found to comply with the

limits for a Class A digital device pursuant to Part 15 of the FCC
Rules. These limits ar e de signed to provide reasonable pro t ection
against harmful inter f erence when the equipment is op erated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with this instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the inte rference at his own
expense.

Note: Modifications or changes not expressly approved by the
manufacturer or the FCC can void your right to operate this
equipment.

Canadian Department of Communications

This Class A di gital apparatus meets all requirements of the
Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe A respecte toutes les exigences
du Règleme nt s ur le matériel brouilleur du Canada.

!

! 1

3

!

4

5

RFI Emission EN55022 Class A
WARNING: In a domestic environment this product may cause radio

interference in which case the user m ay be required to take adequate
measures.

Immunity EN50082-1
Electrical Safety EN60950, UL 1950, CSA 950
Laser EN60825

!

2

!

iii

Electrical Safety and Emission Compliance Statement

IMPORTANT: Appendix A contains translated safety statemen ts for
installing this equipment. When you see the !, go to Appendix A for
the translated safety statement in your language.

WICHTIG: Anhang A enthält übersetzte Sicherheitshinweise für die
Installation dieses Geräts. Wenn Sie ! sehen, schlagen Sie in
Anhang A den übersetzten Sicherheitshinweis in Ihrer Sprache nach.

VIGTIGT: Tillæg A indeholder oversatte sikkerhedsadvarsler, der
vedrører installation af dette udstyr. Når De ser symbolet !, skal De
slå op i tillæg A og find e de oversat te sik kerhed sadvars ler i D eres eget
sprog.

BELANGRIJK: Appendix A bevat vertaalde veiligheidsopmerkingen
voor het installeren van deze apparatuur. Wanneer u de ! ziet,
raadpleeg Appendix A voor vertaalde veiligheidsinstructies in uw taal.

IMPORTANT : L'annexe A contient les instructions de sécurité
relatives à l'installation de cet équipement. Lorsque vous voyez le
symbole !, reportez-vous à l'annexe A pour consulter la traduction
de ces instructions dans votre langue.

TÄRKEÄÄ: Liite A sisältää tämän laitteen asentamiseen liittyvät
käännetyt turvaohjeet. Kun näet !-symbolin, katso käännettyä
turvaohjetta liitteestä A.

IMPORTANTE: l’Appendice A contiene avvisi di sicurezza tradotti
per l’installazione di questa apparecchiatu ra. Il simbolo !, indica di
consultare l’Appendice A per l’avviso di sicurezza nella propria lingua.

VIKTIG: Tillegg A inneholder oversatt sikkerhetsinformasjon for
installering av dette utsty ret. Når du ser !, åpner du til Till egg A for
å finne den oversatte sikkerhetsinformasjonen på ønsket språk.

IMPORTANTE: O Anexo A contém advertências de segurança
traduzidas para instalar este equipamento. Quando vir o símbolo !,
leia a advertência de se gurança traduzida no seu idioma no Anexo A.

IMPORTANTE: El Apéndice A contiene mensajes de seguridad
traducidos para la instalació n de este equipo. Cu ando vea el símbo lo

!

, vaya al Apéndice A para ver el mensaje de seguridad traducido a

su idioma.
OBS! Bilaga A innehåller översatta säkerhet smedd eland en avseende

installationen av denna utrustning. När du ser !, skall du gå till
Bilaga A för att läsa det översatta säkerhetsmeddelandet på ditt
språk.

iv

Table of Contents

Electrical Safety and Emission Compliance Statement ......................iii

Welcome to Allied Telesyn ......................................................................... vii

Where to Find Web-based Guides ...................................................................vii

Documentation Conventions............................................................................vii

Contacting Allied Teleysn...............................................................................viii

For Technical Support and Services................ ........................................viii

Technical Support E-mail Addresses........ ..............................................viii

FTP Server.................................................................................................. ix

For Sales or Corporate Information .................................................................ix

Tell Us What You Think .................. .. .. .. .. .. .. .....................................................ix

Chapter 1

Product Description ...................................................................................... 1

Features.............................................................................................................. 1

Physical Description........................................................................................... 2

LEDs ............................................................................................................ 3

MDI Button.................. ................................................................................ 4

Media Type .............. .. .................................................................................. 4

AC Power Connector ................................................................................... 5

Where to Go Next ................ .. ............................................................................. 5

Chapter 2

Installation ...................................................................................................... 7

Verifying Switch Package Contents .................................................................. 7

Preparing the Site .............................................................................................. 8

Installing the Switch on a Desktop ................................................................... 9

Installing the Switch into a Rack Mount.......... .............................................. 10

Warranty Registration..................................................................................... 11

Chapter 3

Troubleshooting ........................................................................................... 13

How the Switch Reports Problems.................................................................. 13

Network Cabling Problems.............................................................................. 13

Common Problems............................................................................................ 13

Link /Activity LED on Any Port is OFF...................................................14

Power LED is OFF ........................ ............................................................ 14

Calling Technical Support................................................................................ 15

v

Table of Contents

Appendix A

Translated Safety and Emission Information ....................................... 17

Appendix B

Technical Specifications ............................................................................29

Physical Specifications.....................................................................................29

Environmental Specifications.......................................................................... 29

Power Specifications.........................................................................................29

Agency Compliance...........................................................................................29

Appendix C

Technical Support Fax Order ...................................................................31

Incident Summary............................................................................................ 31

Appendix D

AT-FS909SX Installation Guide Feedback .............................................33

vi

Welcome to Allied Telesyn

The guide provides the required information to install and configure
the AT-FS909SX Fast Ethernet Switch.

Where to Find Web-based Guides

Allied Telesyn wants our customers to be well informed by providing
the most up-to-date and most easily accessible way to find our guides
and other technical inform ation.

Visit our website at
related product information.

www.alliedtelesyn.com/techhome.htm

for

Documentation Conventions

Throughout this guide, you will notice several conventions that you
should become familiar with first before installing the product.

Note

A note provides additional information.

Caution

A caution indicates that performing or omitting a specific action
may reasult in equipment damage or loss of data.

Warning

A warning indicates that performing or omitting a specific
action may result in bodily injury.

vii

Welcome to Allied Telesyn

Contacting Allied Teleysn

For Technical Support and Services

Americas

United States, Canada, Mexico,
Central America, South America
Tel: [phone]
Fax: [phone]

Asia

Singapore, Taiwan, Thailand,
Malaysia, Indonesia, Korea,
Philippines, China,
India, Hong Kong
Tel: [phone]
Fax: [phone]

Australia

Australia, New Zealand
Tel: [phone]
Fax: [phone]

France

France, Belgium, Luxembourg, The
Netherlands, Middle East, Africa
Tel: [phone]
Fax: [phone]

Germany

Germany, Switzerland, Austria,
Eastern Europe
Tel: [phone]
Fax: [phone]

Italy

Italy, Spain, Portugal, Greece, Turkey,
Israel
Tel: [phone]
Fax: [phone]

Japan

Tel: [phone]
Fax: [phone]

United Kingdom

United Kingdom, Denmark, Norway,
Sweden, Finland, Iceland
Tel: [phone]
Fax: [phone]

Technical Support E-mail Addresses
United States and Canada

[e-mail]

Latin America, Mexico, Puerto Rico, Caribbean, and
Virgin Islands

[e-mail]

United Kingdom, Sweden, Norw ay, De n mark, and Finland

[e-mail]

viii

AT-FS909SX Installation Guide

FTP Server

Address: gateway.centre.com [lowercase letters]
Login: anonymous [lowerca se letters]
Password: your e-mail address [requested by the server at login]

For Sales or Corporate Information

Allied Telesyn International, Corp.

19800 North Creek Parkway, Suite 200
Bothell, WA 98011
Tel: [phone]
Fax: [phone]

Allied Telesyn International, Corp .

960 Stewart Drive, Suite B
Sunnyvale, CA 94086
Tel: [phone] (USA and Canada)
Fax: [phone]

Tell Us What You Think

In our continuing efforts to help you get the most from Allied Telesyn,
we look for new and b etter ways to doc ument our prod ucts. If you have
comments or suggestions to improve this or other documents, please
fill out the “AT-FS909SX Installation Guide Feedback” on page 33 and
return to us at the address or fax number provided.

ix

Chapter 1

Product Description

This chapter describes the features of the AT-FS909SX Fast Ethernet Switch.

Features

The AT-FS909SX is an unmanaged, Fast Ethernet Switch that provides
familiar Eth ernet tech nolo gy with high -speed access. It is a high-p erform ance
switch that ca n be insta l led on the desktop, or into a 19 -in c h rack. It presents
an affordable, ideal solution to the bottlenecks that can occur in networks
where data-intensive applications and a proliferation of new users is
disrupting network throughput. The switch provides the following features:

❑ Ethernet, Fast Ethernet, and Gigabit Ethernet connectivity:

eight 10/100Base-TX ports with RJ-45 connectors, and one
1000Base-SX port with SC connectors

❑ A small 1.0U high, 13-inch enclosure for desktop, or 19-inch

rack-mount installation

❑ Ha lf- or full-duplex operation via auto-negotiation on the

10/100Mbps ports

❑ Full-duplex ope ration on the 1000Base-SX port

❑ Complies with IEEE 802.3u, IEEE 802.3ab, and IEEE 802.3z

specifications

❑ Store-and-forward switching mode

❑ Supports extended frame lengths up to 1536 bytes

❑ 12K MAC addresses with automatic learning and aging

❑ 4 MB SDRAM for the data buffer of the 10/100Base-TX ports

❑ 2 MB SGRAM for the data buffer of the 1000Base-SX port

❑ LED indicators for Power, and for port Link, Activity, Full-duplex

operation and Collision

❑ One media-dependent interface (MDI) button on Port 1

(10/100Mbps) for hub or PC connection

❑ Internal autoranging power supply (100-240 VAC)

1

Product Description

Physical Description

Figure 1 shows the front panel of the switch.

Figure 1

Figure 2 shows the rear view of the switch showing the AC input and fan
locations.

Figure 3 shows the labels for the LEDs indicators for the two types of ports.

Figure 3

The AT-FS909SX Switch (Front)

Figure 2

LED Indicators Labels (Partial Front Panel)

Rear View of the Switch

2

AT-FS909SX Installation Guide

LEDs

Table 1 describes the switch LEDs. Refer to Figure 3 for the labels for the LEDs
for the two types of ports.

AT-FS909SX LED Indicators

Table 1

LED Color Indicates

Power Green On The switch is powered up and ready for use.

Off The switch is powered off.

Gigabit Ethernet Port Status LEDs

Col/Full Orange On Link is present, full-duplex operation.

Orange Flashing Link is present.
Off Link is not present.

Link/Act Orange On Link is present on this port.

Orange Flashing Packets are being transmitted/received on this port.
Off Link is not present on this port.

10/100Mbps Port Status LEDs

Col/Full Orange On Link is present, full-duplex mode.

Orange Flashing Link is present, half-duplex operation with collisions occurring.

(Typical under Ethernet CSMA/CD.)

Off Link is not present (for full-duplex), or

half-duplex operation established with no collisions occurring.

Link/Act Orange On 100M Link is present; port is enabled.

Orange Flashing 100M Packets are being transmitted/received on this port.
Green On 10M Link is present; port is enabled.
Green Flashing 10M Packets are being transmitted/received on this port.
Off Link is not present.

3

Product Description

MDI Button

The MDI provides you with the flexibilit y for using a st raight-through cab le to
connect to a hub or another switch, or to any DTE such as an end station or a
server. The button is associated with Port 1. Table 2 describes the MDI button
positions.

MDI Positions

Table 2

Position Label Use

X
To PC

To connect a DTE to the port

Out

=

In

To Hub

To connect a hub or another switch to the port

Media Type

Table 3 describes the standard (connectors), media, and maximum distances
for each port type.

Media Types and Distances

Table 3

Standard Media Type

1000Base-SX
(Short Wave = 850 nm)

100Base-TX Category 5 UTP Cable (100 Mbps) 100 m (328 ft)

50/125um Multimode Fiber
Single-mode: not supported

62.5/125um Multimode Fiber
Single-mode: not supported

MHz/Km
Rating

500 550 m (1804 ft)

160 220 m (722 ft)

Maximum
Distance

10Base-T Category 3 UTP Cable (10 Mbps) 100 m (328 ft)

4

AT-FS909SX Installation Guide

AC Power Connector

The switch has a single AC power supply socket in the rear panel, which has
autoranging AC voltage inputs. The input voltage range is 100-240 VAC,
50/60 Hz. The power cord acts as an ON/OFF switch.

Where to Go Next

Proceed to Chapter 2 fo r details on how to install the swi tch .

5

Chapter 2

Installation

This chapter describes the how to install the AT-FS909SX on a desktop, or into
a 19-inch rack.

Verifying Switch Package Contents

Make sure the following items are included in your switch package. If any of
the following ite ms are missin g or damaged , contac t your sale s repre sentative.

❑ One AT-FS909SX switch

❑ This Installation Guide

❑ Warranty card

❑ Four rubber feet for desktop installation

❑ Two brackets, eight flathead Phillips screws, and four large screws

and nylon washers for installation into a 19-inch rack

❑ Power cord (Americas, EC, Australia, and UK only)

❑ Additional serial number stickers, for your convenience

7

Installation

Preparing the Site

Use common sense w he n s electing a location f or the swi tc h and obser ve the
following:

❑ Make sure that the switch’s power is accessible and cables can b e

connected easily.

❑ Cabling must be away from sources of electrical nois e such as radios,

transmitters, broadband amplifiers, power lines, electric motors, and
fluorescent fixtures.

❑ Air flow around the switch and through its vents on the side and rear

must not be restricted.

❑ If you are installing the switch on a desk, make sure it is placed on a

level, secure desktop.

❑ Do not place objects on top of the switch.

❑ Do not expose the switch to moisture or water.

❑ Make sure it is in a dust-fre e environme nt.

❑ Use de dic a ted po wer circuits or power conditioners to supply reliable

electrical power to the network devices.

Review the following precautions before you begin to install the switch.

Warning

LIGHTNING DANGER
DANGER: DO NOT WORK on equipment or CABLES during
periods of LIGHTNING ACTIVITY. ! 9

Warning

ELECTRICAL - TYPE CLASS 1 EQUIPMENT
THIS EQUIPMENT MUST BE EARTHED. Power plug must be
connected to a properly wired earth ground socket outlet. An
improperly wired socket outlet could place hazardous voltages on

.

accessible metal parts

Continue with the desktop installation steps on page 9, or the rack-mount
installatio n steps on page 10.

8

!

11

AT-FS909SX Installation Guide

Installing the Switch on a Desktop

1. Locate a level, secure surface for the s w itch.

2. Apply the four rubber feet to the bottom of the switch.

3. Place the switch on the desktop.

Warning

The power cord is used as a disconnection device. To de-energize
equipment, disconnect the power cord. ! 10

4. Apply power to the switch by plugging the power cord into the rear of
the unit and plugging the other end into a wall outlet. Verify that the
Power LED lights green.

If the Power LED does not light green, refer to Chapter 3, for further
information.

Warning

Do not stare into the laser beam. ! 7

5. Connect the data cables and observe normal operation as indicated by

the port LEDs. Refer to Table 1 on page 3 for LED information. For
Port 1, set the MDI Button to the correct setting. Refer to Table 2 on
page 4 for the MDI setting.

6. Optional: place one of the additional serial number stickers supplied

with your switch on an accessible part of the switch for your
convenient reference.

9

Installation

Installing the Switch into a Rack Mount

Caution

Do not use power tools to perform this installation.

1. Remove all cables and the power cord from the switch (if previously

attached).

Caution

Air vents must not be blocked and must have free access to the room
ambient air for cooling. ! 13

2. Attach the rackmounting brackets to each side of the switch as shown
in Figure 4, using the eight flathead screws that came in the switch
package.

Bracket

Figure 4

Attaching Rackmounting Brackets

Bracket

3. Mount the switch into the rack using four large pan-head screws and
nylon washers (provided).

4. Ensure that there is unrestricted air flow around the switch.

Warning

The power cord is used as a disconnection device. To de-energize
equipment, disconnect the power cord. ! 10

5. Apply power to the switch by plugging the power cord into the rear of
the unit and plugging the other end into a power outlet.

If the Power LED does not light green, refer to Chapter 3,
Troubleshooting, fo r fu rther information.

10

AT-FS909SX Installation Guide

Warning

Do not stare into the laser beam. ! 7

6. Connect the data cables and observe normal operation as indicated by
the port LEDs. Refer to Table 1 on page 3 for LED information. For
Port 1, set the MDI Button to the correct setting. Refer to Table 2 on
page 4 for the MDI setting.

7. Optional: place one of the additional serial number stickers supplied
with your switch on an accessible part of the switch for your
convenient reference.

Warranty Registration

When you finish the installation, register your product by completing the
enclosed warranty card and sending it in, or by visiting our web site at
www.alliedtelesyn.com/warr-reg.htm and completing the on-line
registration.

11

Chapter 3

Troubleshooting

This chapter pro vid es i nf orm atio n on how to det e ct and res olve p ro ble ms wi th
your switch. This chapter includes the following sections:

❑ How the Switch Reports Problems
❑ Network Cabling Problems
❑ Common Problems
❑ Calling Technical Support

How the Switch Reports Problems

The LEDs indicate problems with the ports and power. See Table 1 on page 3
for a description of the switch LEDs.

Network Cabling Problems

If you have 100Base-TX (Fast Ethernet), some network problems may be
related to exceeding cabling distances. Refer to the standard IEEE 802.3u,
Clause 29.3.1.2 on Worst Case Path Delay Value. This document specifies
that the collision domain diameter must be within the following limits:

❑ Under 100 m (328 ft) for TX cabling

Common Problems

This section lists common possible sources of error and actions required to
correct them.

13

Troubleshooting

Link /Activity LED on Any Port is OFF

This can indicate:

❑ A loose data cable.
❑ The device at the other end of the connection is turned OFF.
❑ The data cable is not wired correctly (straight/crossed) for the device.

Perform the fo llo wing st eps i n se qu en ce; yo u need not proceed to the n ext step
if the problem is resolved:

1. Make sure t h e data cables are s e cure.

2. Make sure the device at the end of the connection is turned ON.

3. Make sure the data cable is wired correctly (straight/crossed) for the
device.

4. Contact Allied Telesyn’s Technical Support for help.

Power LED is OFF

When there is no power to the swi tch, it cannot operate.
A Power LED that is OFF can indicate:

❑ A loose power cord.
❑ Power supply failure, malfunction, or loss of power to the power

supply.

❑ A power supply voltage below acceptable levels.
❑ A high switch temperature due to fan failure or extreme a mbient

temperature.

Perform the fo llo wing st eps i n se qu en ce; yo u need not proceed to the n ext step
if the problem is resolved:

1. Secure the power cord to the power source and check the Power LED
to see if it is ON.

2. Ensure that the voltage is within the required levels in your region.

3. Contact Allied Telesyn’s Technical Support for help.

14

AT-FS909SX Installation Guide

Calling Technical Support

When contacting Alli ed Telesyn for suppo r t o n any of i t s products, provid e
Technical Support with the following information:

❑ Model and serial number
❑ Description of the problem

Refer to page viii or visit our web site at www.alliedtelesyn.com for a list of
worldwide locations and contact information.

15

Appendix A

Translated Safety and Emission Information

IMPORTANT: This appendix co ntains multi ple-languag e translations fo r the
safety statements in this guide.

WICHTIG: Dieser Anhang enthält Übersetzungen der i n di es em Handbuch
enthaltenen Sicherheitshinweise in mehreren Sprachen.

VIGTIGT: Dette tillæg indeholder oversættelser i flere sprog af
sikkerhedsadvarslerne i denne håndbog.

BELANGRIJK: Deze appendix bevat vertalingen in meerdere talen van de
veiligheidsopmerkingen in deze gids.

IMPORTANT: Cette annexe contient la traduction en plusieurs langues des
instructions de sécurité figurant dans ce guide.

TÄRKEÄÄ: Tämä liite sisältää tässä oppaassa esiintyvät turvaohjeet usealla
kielellä.

IMPORTANTE: questa appendice contiene traduzioni in più lingue degli
avvisi di sicurezza di questa guida.

VIKTIG: Dette tillegget inneholder oversettelser til flere språk av
sikkerhetsinformasjonen i denne veiledningen.

IMPORTANTE: Este anexo contém traduções em vários idiomas das
advertências de segurança neste guia.

IMPORTANTE: Este apéndice con tiene traduccion es en mú ltiples idio mas de
los mensajes de seguridad incluidos en esta guía.

OBS! Denna bilaga innehåller flerspråkiga översättningar av
säkerhetsmeddelandena i de nna handledn ing.

17

Translated Safety and Emission Information

Standards

RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a

Class A digital device pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with this instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense.

Note: Modifications or changes not expressly approved by the manufacturer or the
FCC can void your right to operate this equipment.

This Class A digital apparatus meets all requirements of the Canadia n
Interference-Causing Equipment Regulation s.

Cet appareil numérique de la classe A respecte toutes les exigences du Règlement
sur le matériel brouilleur du Canada.

1 RFI Emission EN55022 Class A

!

2

!

3 Immunity EN50082-1

!

4 Electrical Safety EN60950, UL1950, CSA 950

!

5 Laser EN60825

!

6

!

7

!

8

!

9

!

10

!

11 ELECTRICAL - TYPE CLASS 1 EQUIPMENT

!

WARNING

which case the user may be required to take adequate measures.

SAFETY
WARNING
WARNING
ELECTRICAL NOTICES

WARNING:

To prevent ELECTRIC shock, do not remove the cover. No user-serviceable parts
inside. This unit contains HAZARDOU S VOLTA GE S and shoul d only be opened by a
trained and qualified technician. To avoid the possibility of ELECTRIC SHOCK,
disconnect electric power to the product before connecting or disconnecting the LAN
cables.

LIGHTNING DANGER
DANGER:

LIGHTNING ACTIVITY.

CAUTION:

ENERGIZE EQUIPMENT, disconnect the power cord.

THIS EQUIPMENT MUST BE EARTHED. Power plug must be connected to a
properly wired earth ground socket outlet. An improperly wired socket outlet could
place hazardous voltages on accessible metal parts.

: This product meets the following standards.

U.S. Federal Communications Commission

Canadian Department of Communications

: In a domestic environment this product may cause radio inte rference in

: Class 1 Laser product.
: Do not stare into the laser beam.

ELECTRIC SHOCK HAZARD

DO NOT WORK on equipment or CABLES during periods of

POWER CORD IS USED AS A DISCONNECTION DEVICE. TO DE-

18

AT-FS909SX Installation Guide

12 PLUGGABLE EQUIPMENT, the socket outlet shall be installed near the equipment

!

13

!

14

!

15

!

1 Hochfrequenzstörung EN55022 Klasse A

!

2

!

3 Störsicherheit EN50082-1

!

4 Elektrische Sicherheit EN60950, UL1950, CSA 950

!

5 Laser EN60825

!

6

!

7

!

8

!

9

!

10

!

11 GERÄTE DER KLASSE 1

!

12 STECKBARES GERÄT: Die Anschlußbuchse sollte in der Nähe der Einrichtung

!

13

!

14

!

15

!

and shall be easily accessible.

CAUTION:

ambient air for cooling.

OPERATING TEMPERATURE:

temperature of 40° degrees C.

ALL COUNTRIES:

Codes.

Normen

WARNUNG

hervorrufen. In diesem Fall müßte der Anwender angemessene Gegenmaßnahmen
ergreifen.

SICHERHEIT
WARNUNG
WARNUNG
ACHTUNG:

Das Gehäuse nicht öffnen. Das Gerät enthält keine vom Benutzer wartbaren Teile.
Das Gerät steht unter Hochspannung und darf nur von qualifiziertem technischem
Personal geöffnet werden. Vor Anschluß der LAN-Kabel, Gerät vom Netz trennen.

GEFAHR DURCH BLITZSCHL AG
GEFAHR:

ausführen.

VORSICHT:

STROMVERSORGUNG. ZUR TRENNUNG VOM NETZ, KABEL AUS DE
STECKDOSE ZIEHEN.

DIESE GERÄTE MÜSSEN GEERDET SEIN. Der Netzstecker darf nur mit einer
vorschriftsmäßig geerdeten Steckdose verbunden werden. Ein unvorschriftsmäßiger
Anschluß kann die Metallteile des Gehauses unter gefährliche elektrische
Spannungen setzen.

angebracht werden und leicht zugänglich sein."

VORSICHT

Die Entlüftungsöffnungen dürfen nicht versperrt sein und müssen zum Kühlen freien
Zugang zur Raumluft haben.

BETRIEBSTEMPERATUR:

Umgebungstemperatur von nicht mehr als 40° C entworfen.

ALLE LÄNDER:

entsprechen.

Air vents must not be blocked and must have free access to the room

This product is designed for a maximum ambient

Install product in accordance with local and National Electrical

: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen.

: Bei Verwendung zu Hause kann dieses Produkt Funkstörungen

Laserprodukt der Klasse 1.
Nicht direkt in den Strahl blicken.
GEFÄHRLICHE SPANNUNG

Keine Arbeiten am Gerät oder an den Kabeln während eines Gewitters

DAS NETZKABEL DIENT ZUM TRENNEN DE

Dieses Produkt wurde für den Betrieb in einer

Installation muß örtlichen und nationalen elektrischen Vorschriften

19

Translated Safety and Emission Information

Standarder

1 Radiofrekvens forstyrrelsesemission EN55022 Klasse A

!

2

!

3 Immunitet EN50082-1

!

4 Elektrisk sikkerhed EN60950, UL1950, CSA 950

!

5 Laser EN60825

!

6

!

7

!

8

!

9

!

10

!

11 ELEKTRISK - KLASSE 1-UDSTYR

!

12 UDSTYR TIL STIKKONTAKT, stikkontakten bør installeres nær ved udstyret og skal

!

13

!

14

!

15

!

ADVARSEL

Bliver det tilfældet, påkræves brugeren muligvis at tage tilstrækkelige
foranstaltninger.

SIKKERHED
ADVARSEL
ADVARSEL
ELEKTRISKE FORHOLDSREGLER

ADVARSEL:

For at forebygge ELEKTRISK stød, undlad at åbne apparatet. Der er ingen indre dele,
der kan repareres af brugeren. Denne enhed indehold e r LIVSFARLIGE
STRØMSPÆNDINGER og bør kun åbnes af en uddannet og kvalificeret tekniker. For
at undgå risiko for ELEKTRISK STØD, afbrydes den elektriske strøm til produktet,
før LAN-kablerne monteres eller afmonteres.

FARE UNDER UVEJR
FARE:

LYNAKTIVITET.

ADVARSEL:

STRØMMEN. SKAL STRØMMEN TIL APPARATET AFBRYDES, tages ledningen
ud af stikket.

DETTE UDSTYR KRÆVER JORDFORBINDELSE. Stikket skal være forbundet med
en korrekt installeret jordforbunden stikkontakt. En ukorrekt installeret stikkontakt
kan sætte livsfarlig spænding til tilgængelige metaldele.

være lettilgængelig.

ADVARSEL:

omgivende luft i rummet for afkøling.

BETJENINGSTEMPERATUR:

temperatur på maksimum 40 grader C.

ALLE LANDE:

national lovgivning for elektriske installationer.

: Dette produkt tilfredsstiller de følgende standarder.

: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse.

Laserprodukt av klasse 1.
Stirr ikke på strålen.

RISIKO FOR ELEKTRISK STØD

UNDLAD at arbejde på udstyr eller KABLER i perioder med

DEN STRØMFØRENDE LEDNING BRUGES TIL AT AFBRYDE

Ventilationsåbninger må ikke blokeres og skal have fri adgang til den

Dette apparat er konstrueret til en omgivende

Installation af produktet skal ske i overensstemmelse med lokal og

20

AT-FS909SX Installation Guide

: Dit product voldoet aan de volgende eisen.

Eisen

1 RFI Emissie EN55022 Klasse A

!

2

!

3 Immuniteit EN50082-1

!

4 Electrische Veiligheid EN60950, UL1950, CSA 950

!

5 Laser EN60825

!

6

!

7

!

8

!

9

!

10

!

11 ELEKTRISCHE TOESTELLEN VAN KLASSE 1

!

12 AAN TE SLUITEN APPARATUUR, de contactdoos wordt in de nabijheid van de

!

13

!

14

!

15

!

WAARSCHUWING

geval de gebruiker verplicht kan worden om gepaste maatregelen te nemen.

VEILIGHEID
WAARSHUWING
WAARCHUWING
WAARSCHUWINGEN MET BETREKKING TOT ELEKTRICITEIT

WAARSCHUWING:

Verwijder het deksel niet, teneinde ELEKTRISCHE schokken te voorkomen. Binnenin
bevinden zich geen onderdelen die door de gebruiker onderhouden kunnen worden. Dit
toestel staat onder GEVAARLIJKE SPANNING en mag alleen worden geopend door
een daartoe opgeleide en bevoegde technicus. Om het gevaar op ELEKTRISCHE
SCHOKKEN te vermijden, moet u het toestel van de stroombron ontkoppelen alvorens
de LAN-kabels te koppelen of ontkoppelen.

GEVAAR VOOR BLIKSEMINSLAG
GEVAAR:

WAARSCHUWING:

STROOMKABEL TE ONTKOPPELEN.OM HET T OESTEL STROOMLOOS TE
MAKEN: de stroomkabel ontkoppelen.

DIT TOESTEL MOET GEAARD WORDEN. De stekker moet aangesloten zijn op een
juist geaarde contactdoos. Een onjuist geaarde contactdoos kan de metalen onderdelen
waarmee de gebruiker eventueel in aanraking komt onder gevaarlijke spanning
stellen.

apparatuur geïnstalleerd en is gemakkelijk te bereiken."

OPGELET:

omgevingslucht ongehinderd toelaten voor afkoeling.

BEDRIJFSTEMPERATUUR:

meer bedragen dan 40 graden Celsius.

ALLE LANDEN:

elektrische voorschriften.

NIET aan toestellen of KABELS WERKEN bij BLIKSEM.

: Binnenshuis kan dit product radiostoring veroorzaken, in welk

Klasse-1 laser produkt.

Neit in de straal staren.

GEVAAR VOOR ELEKTRISCHE SCHOKKEN

HET TOESTEL WORDT UITGESCHAKELD DOOR DE

De ventilatiegaten mogen niet worden gesperd en moeten de

De omgevingstemperatuur voor dit produkt mag niet

het toestel installeren overeenkomstig de lokale en nationale

21

Translated Safety and Emission Information

Normes:

1 Emission d’interférences radioélectriques EN55022 Classe

!

2

!

3 Immunité EN50082-1

!

4 Sécurité électrique EN60950, UL1950, CSA 950

!

5 Laser EN60825

!

6

!

7

!

8

!

9

!

10

!

11 ÉQUIPEMENT DE CLASSE 1 ÉLECTRIQUE

!

12 EQUIPEMENT POUR BRANCHEMENT ELECTRIQUE, la prise de sortie doit être

!

13

!

14

!

15

!

MISE EN GARDE

des interférences radioélectriques. Auquel cas, l’utilisateur devra prendre les mesures
adéquates.

SÉCURITÉ
ATTENTION
ATTENTION
INFORMATION SUR LES RISQUES ÉLECTRIQUES

AVERTISSEMENT

Pour éviter toute ÉLECTROCUTION, ne pas ôter le revêtement protecteur du
matériel. Ce matériel ne contient aucun élément réparable par l’utilisateur. Il
comprend des TENSIONS DANGEREUSES et ne doit être ouvert que par un
technicien dûment qualifié. Pour éviter tout risque d’ÉLECTROCUTION, débrancher
le matériel avant de connecter ou de déconnecter les câbles LAN.

DANGER DE FOUDRE
DANGER:

ATTENTION:

POUR COUPER L’ALIMENTATION DU MATÉRIEL, débrancher le cordon.

CE MATÉRIEL DOIT ÊTRE MIS A LA TERRE. La prise de courant doit être branchée
dans une prise femelle correctement mise à la terre car des tensions dangereuses
risqueraient d’atteindre les pièces métalliques accessibles à l’utilisateur.

placée près de l’équipement et facilement accessible".

ATTENTION:

circuler librement pour le refroidissement.

TEMPÉRATURE DE FONCTIONNEMENT:

température ambiante maximum de ou 40 degrés Celsius.

POUR TOUS PAYS:

nationales et locales.

ce produit est conforme aux normes de suivantes:

A

: dans un environnement domestique, ce produit peut provoquer

Producit laser di classe 1.
Ne pas fixer le faisceau des yeux.

: DANGER D’ÉLECTROCUTION

NE PAS MANIER le matériel ou les CÂBLES lors d’activité orageuse.

LE CORDON D’ALIMENTATION SERT DE MISE HORS CIRCUIT.

Ne pas bloquer les fentes d’aération, ceci empêcherait l’air ambiant de

Ce matériel est capable de tolérer une

Installer le matériel conformément aux normes électriques

22

AT-FS909SX Installation Guide

Standardit

1 Radioaaltojen häirintä EN55022 Luokka A

!

2 VAROITUS: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä, missä

!

3 Kestävyys EN50082-1

!

4 Sähköturvallisuus EN60950, UL1950, CSA 950

!

5 Laser EN60825

!

6

!

7

!

8

!

9

!

10

!

11 SÄHKÖ - TYYPPILUOKAN 1 LAITTEET

!

12 PISTORASIAAN KYTKETTÄVÄ LAITE; pistorasia on asennettava laitteen lähelle ja

!

13

!

14

!

15

!

tapauksessa laitteen käyttäjän on mahdollis est i ryhdyttä vä tarpee llis iin
toimenpiteisiin.

TURVALLISUUS
VAROITUS
VARIOTUS
SÄHKÖÖN LIITTYVIÄ HUOMAUTUKSIA

VAROITUS:

Estääksesi SÄHKÖISKUN älä poista kantta. Sisällä ei ole käyttäjän huollettavissa
olevia osia. Tämä laite sisältää VAARALLISIA JÄNNITTEITÄ ja sen voi avata vain
koulutettu ja pätevä teknikko. Välttääksesi S ÄHKÖ ISKU N mahdollisuude n katkaise
sähkövirta tuotteeseen ennen kuin liität tai irrotat paikallisverkon (LAN) kaapelit.

SALAMANISKUVAARA
HENGENVAARA:

SALAMOINNIN A IK A NA .

HUOMAUTUS:

VIRTA KATKAISTAAN irrottamalla virtajohto.

TÄMÄ LAITE TÄYTYY MAADOITTAA. Pistoke täytyy liittää kunnollisesti
maadoitettuun pistorasiaan. Virheellisesti johdotettu pistorasia voi altista a
metalliosat vaarallisille jännitteille.

siihen on oltava esteetön pääsy."

HUOMAUTUS:

ympäröivään huoneilmaan, jotta ilmanvaihto tapahtuisi.

KÄYTTÖLÄMPÖTILA:

maksimilämpötilalle 40°C.

KAIKKI MAAT:

sähköturvallisuusmääräysten mukaisesti.

: Tämä tuote on seuraavien standardien mukainen.

Luokan 1 Lasertuote.
Älä katso säteeseen.

SÄHKÖISKUVAARA

ÄLÄ TYÖSKENTELE laitteiden tai KAAPELEIDEN KANSSA

VIRTAJOHTOA KÄYTETÄÄN VIRRANKATKAISULAITTEENA.

Ilmavaihtoreikiä ei pidä tukkia ja niillä täytyy olla vapaa yhteys

Tämä tuote on suunniteltu ympäröivän ilman

Asenna tuote paikallisten ja kansallisten

23

Translated Safety and Emission Information

Standard

1 Emissione RFI (interferenza di radiofrequenza) EN55022 Classe A

!

2

!

3 Immunità EN50082-1

!

4 Sicurezza elettrica EN60950, UL1950, CSA 950

!

5 Laser EN60825

!

6

!

7

!

8

!

9

!

10

!

11 ELETTRICITÀ - DISPOSITIVI DI CLASSE 1

!

12 APPARECCHIATURA COLLEGABILE, la pr esa v a in stallata vicino all’apparecchio

!

13

!

14

!

15

!

AVVERTENZA:

interferenza. In questo caso potrebbe richiedersi all’utente di prendere gli adeguati
provvedimenti.

NORME DI SICUREZZA
AVVERTENZA
AVERTENZA
AVVERTENZE ELETTRICHE

ATTENZIONE:

Per evitare SCOSSE ELETTRICHE non asportare il coperchio. Le componenti interne
non sono riparabili dall’utente. Questa unità ha TENSIONI PERICOLOSE e va aperta
solamente da un tecnico specializzato e qualificato. Per evitare ogni possibilità di
SCOSSE ELETTRICHE, interrompere l’alimentazione del dispositivo prima di
collegare o staccare i cavi LAN.

PERICOLO DI FULMINI
PERICOLO:

TEMPORALESCHE.

ATTENZIONE:

DISATTIVAZIONE. PER TOGLIERE L A CORRENTE AL DISPOSITIVO staccare il
cavo di alimentazione.

QUESTO DISPOSITIVO DEVE AVERE LA MESSA A TERRA. La spina deve essere
inserita in una presa di corrente specificamente dotata di messa a terra. Una presa
non cablata in maniera corretta rischia di scaricare una tensione pericolosa su parti
metalliche accessibili.

per risultare facilmente accessibile".

ATTENZIONE:

ricircolo dell’aria ambiente per il raffreddamento.

TEMPERATURA DI FUNZIONAMENTO:

temperatura ambientale massima di 40 gradi centigradi.

TUTTI I PAESI:

nazionali.

: Questo prodotto è conforme ai seguenti standard.

in ambiente domestico questo prodotto potrebbe causare radio

Prodotto laser di Classe 1.

Non fissare il raggio con gli occhi.

PERICOLO DI SCOSSE ELETTRICHE

NON LAVORARE sul dispositivo o sui CAVI durante PRECIPITAZIONI

IL CAVO DI ALIMENTAZIONE È USATO COME DISPOSITIVO DI

le prese d’aria non vanno ostruite e devono consentire il libero

Questo prodotto è concepito per una

installare il prodotto in conformità delle vigenti normative elettriche

24

AT-FS909SX Installation Guide

Sikkerhetsnormer

1 RFI stråling EN55022 Klasse A

!

2

!

3 Immunitet EN50082-1

!

4 Elektrisk sikkerhet EN60950, UL1950, CSA 950

!

5 Laser EN60825

!

6

!

7

!

8

!

9

!

10

!

11 ELEKTRISK - TYPE 1- KLASSE UTSTYR

!

12 UTSTYR FOR STIKKONTAKT. Stikkontakten skal monteres i nærheten av utstyret

!

13

!

14

!

15

!

ADVARSEL

radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige forholdsregler.

SIKKERHET
ADVARSEL
ADVARSAL
ELEKTRISITET

ADVARSEL:

For å unngå ELEKTRISK sjokk, må dekslet ikke tas av. Det finnes ingen deler som
brukeren kan reparere på innsiden. Denne enheten inneholder FARLIGE
SPENNINGER, og må kun åpnes av en faglig kvalifisert tekniker. For å unngå
ELEKTRISK SJOKK må den elektriske strømmen til produktet være avslått før LAN­kablene til- eller frakobles.

FARE FOR LYNNEDSLAG

ARBEID IKKE på utstyr eller KABLER i TORDENVÆR.

FARE:
FORSIKTIG:

Å DEAKTIVISERE UTSTYRET, må strømforsyningen kobles fra.

DETTE UTSTYRET MÅ JORDES. Strømkontakten må være tilkoplet en korrekt
jordet kontakt. En kontakt som ikke er korrekt jordet kan føre til farlig spenninger i
lett t ilgjengelige metalldeler.

og skal være lett tilgjengelig."

FORSIKTIG:

romtemperatur for avkjøling.

DRIFTSTEMPERATUR:

romtemperatur på 40 grader celsius.

ALLE LAND:

elektriske koder.

: Dette produktet tilfredsstiller følgende sikkerhetsnormer.

: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake

Laserprodukt av klasse 1.
Stirr ikke på strålen.

FARE FOR ELEKTRISK SJOKK

STRØMLEDNINGEN BRUKES TIL Å FRAKOBLE UTSTYRET. FOR

Lufteventilene må ikke blokkeres, og må ha fri tilgang til luft med

Dette produktet er konstruert for bruk i maksimum

Produktet må installeres i samsvar med de lokale og nasjonale

25

Translated Safety and Emission Information

Padrões

1 Emissão de interferência de radiofrequênciaEN55022 Classe A

!

2

!

3 Imunidade EN50082-1

!

4 Segurança Eléctrica EN60950, UL1950, CSA 950

!

5 Laser EN60825

!

6

!

7

!

8

!

9

!

10

!

11 ELÉTRICO - EQUIPAMENTOS DO TIPO CLASSE 1

!

12 EQUIPAMENTO DE LIGAÇÃO, a tomada eléctrica deve estar instalada perto do

!

13

!

14

!

15

!

AVISO

radiorrecepção e, neste caso, pode ser necessário que o utente tome as medidas
adequadas.

SEGURANÇA
AVISO
AVISO
AVISOS SOBRE CARACTERÍSTICAS ELÉTRICAS

ATENÇÃO:

Para evitar CHOQUE ELÉTRICO, não retire a tampa. Não contém peças que possam
ser consertadas pelo usuário. Este aparelho contém VOLTAGENS PERIGOSAS e só
deve ser aberto por um técnico qualificado e treinado. Para evitar a possibilidade de
CHOQUE ELÉTRICO, desconecte o apa re lho da fo nte de energia elétrica antes de
conectar e desconectar os cabos da LAN.

PERIGO DE CHOQUE CAUSADO POR RAIO
PERIGO:

suscetíveis a QUEDAS DE RAIO.

CUIDADO:

DE DESCONEXÃO. PARA DESELETRIFICAR O EQUIPAMENTO, desconecte o cabo
de ALIMENTAÇÃO.

DEVE SER FEITA LIGAÇÃO DE FIO TERRA PARA ESTE EQU IPAMENTO. O
plugue de alimentação deve ser conectado a uma tomada com adequada ligação de fio
terra. Tomadas sem adequada ligação de fio terra podem transmitir voltagens
perigosas a peças metálicas expostas.

equipamento e ser de fácil acesso."

CUIDADO:

livre ao ar ambiente para arrefecimento adequado do aparelho.

TEMPERATURA DE FUNCIONAME NTO:

temperatura ambiente máxima de 40 graus centígrados.

TODOS OS PAÍSES:

para instalações elétricas.

: Este produto atende aos seguintes padrões.

: Num ambiente doméstico este produto pode causar interferência na

Produto laser de classe 1
Não olhe fixamente para o raio.

PERIGO DE CHOQUE ELÉTRICO

NÃO TRABALHE no equipamento ou nos CABOS durante períodos

O CABO DE ALIMENTAÇÃO É UTILIZADO COMO UM DISPOSITIVO

As aberturas de ventilação não devem ser bloqueadas e devem ter acesso

Este produto foi projetado para uma

Instale o produto de acordo com as normas nacionais e locais

26

AT-FS909SX Installation Guide

Estándares:

1 Emisión RFI EN55022 Clase

!

2

!

3 Inmunidad EN50082-1

!

4 Seguridad eléctrica EN60950, UL1950, CSA 950

!

5 Laser EN60825

!

6

!

7

!

8

!

9

!

10

!

11 ELECTRICO - EQUIPO DEL TIPO CLASE 1

!

12 EQUIPO CONECTABLE, el tomacorriente se debe instalar cerca del equipo, en un

!

13

!

14

!

15

!

ADVERTENCIA

radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las medidas
que sean convenientes al respecto.

SEGURIDAD
¡ADVERTENCIA!
¡ADVERTENCIA!
AVISOS ELECTRICOS

ADVERTENCIA:

Para evitar un ELECTROCHOQUE, no quite la tapa. No hay ningún componente en
el interior al cual puede prestar servicio el usuario. Esta unidad contiene VOLTAJES
PELIGROSOS y sólo deberá abrirla un técnico entrenado y calificado. Para evitar la
posibilidad de ELECTROCHOQUE desconecte la corriente eléctrica que llega al
producto antes de conectar o desconectar los cables LAN.

PELIGRO DE RAYOS
PELIGRO:

equipos o en LOS CABLES durante TORMENTAS ELECT RICAS.

ATENCION:

DISPOSITIVO DE DESCONEXION. PARA DESACTIVAR EL EQUIPO, d esc onecte
el cable de alimentación.

ESTE EQUIPO TIENE QUE TENER CONEX ION A TIERRA. El cable tiene que
conectarse a un enchufe a tierra debidamente instalado. Un enchufe que no está
correctamente instalado podría ocasionar tensiones peligrosas en las partes metálicas
que están expuestas.

lugar con acceso fácil".

ATENCION:

acceso libre al aire ambiental de la sala para su enfriamiento.

TEMPERATURA REQUERIDA PARA LA OPERACIÓN:

diseñado para una temperatura ambiental máxima de 40 grados C.

PARA TODOS LOS PAÍSES:

Eléctricos locales y nacionales.

Este producto cumple con los siguientes estándares.

A

: en un entorno doméstico, este producto puede causar

Producto láser Clase 1.
No mirat fijamente el haz.

PELIGRO DE ELECTROCHOQUE

NO REALICE NINGUN TIPO DE TRABAJO O CONEXION en los

EL CABLE DE ALIMENTACION SE USA COMO UN

Las aberturas para ventilación no deberán bloquearse y deberán tener

Este producto está

Monte el producto de acuerdo con los Códigos

27

Translated Safety and Emission Information

Standarder: Denna produkt uppfyller följande standarder.

1 Radiostörning EN55022 Klass A

!

2

!

3 Immunitet EN50082-1

!

4 Elsäkerhet EN60950, UL1950, CSA 950

!

5 Laser EN60825

!

6

!

7

!

8

!

9

!

10

!

11 ELEKTRISKT -- TYP KLASS 1 UTRUSTNING

!

12

!

13

!

14

!

15

!

VARNING:

tvinga användaren till att vidtaga erforderliga åtgärder

SÄKERHET
VARNING!
VARNING!
TILLKÄNNAGIVANDEN BETRÄFFANDE ELEKTRICITETSRISK:
RISK FÖR ELEKTRISK STÖT

Det finns inga delar inuti som behöver underhålla s. Denna app arat är und er
HÖGSPÄNNING och får endast öppnas av en utbildad kvalificerad tekniker. För att
undvika ELEKTRISK STÖT, koppla ifrån produkt ens strömanslut n i ng innan LAN­kablarna ansluts eller kopplas ur.

FARA FÖR BLIXTNEDSLAG
FARA:
VARNING:

FRÅN STRÖMMEN, dra ur nätkabeln.

DENNA UTRUSTNING MÅSTE VARA JORDAD. Nä tka be ln måste v ara ansluten till
ett ordentligt jordat uttag. Ett felaktigt uttag kan göra att närliggande metalldelar
utsätts för högspänning. Apparaten skall anslutas till jordat uttag, när den ansluts till
ett nätverk.

UTRUSTNING MED PLUGG.

vara lättåtkomligt".

VARNING:

rumsluft för avsvalning.

DRIFTSTEMPERATUR

Denna produkt är konstruerad för rumstemperatur ej överstigande 40 grader Celsius

Alla länder:

elektrisk utrustning.

Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan

Laserprodukt av klass 1.

Laserstrålning när enheten är öppen.

För att undvika ELEKTRISK stöt, ta ej av locket.

ARBETA EJ på utrustningen eller kablarna vid ÅSKV ÄDER.

NÄTKABELN ANVÄNDS SOM STRÖMBRYTARE FÖR ATT KOPPLA

Uttaget skall installeras i utrustningens närhet och

Luftventilerna får ej blockeras och måste ha fri tillgång till omgivande

Installera produkten i enlighet med lokala och statliga bestämmelser för

28

Appendix B

Technical Specifications

The sections that follow list the technical specifications for the AT-FS909SX.

Physical Sp ecifications

Dimensions: (W x D x H)

330 mm x 230 mm x 43 mm
(13 in x 9.05 in x 1.69 in)

Weight: 2.55 kg (5.6 lb)

Environmental Specifications

Operating Temperature: 0° to 40° C (32° to 104° F)
Storage Temperature: -20° to 70° C (-4° to 158° F)
Operating Humidity: 10% to 90% non-condensing
Non-operating Humidity: 10% to 95% non-condensing

Power Specifications

Maximum Power

Consumption: 13.7 W

AC Input Voltage: 100-240VAC, 50/60Hz.

Agency Compliance

Standard: IEEE 802.3u, IEEE 802.3ab, IEEE 802.3z
EMI/RFI: Meets FCC Class A, EN55022 Class A,

VCCI Class A

Safety: Conforms to UL 1950, CSA C22.2 No. 950,

TUV EN 60950
Immunity: Conforms to EN50082-1
CE Compliant

29

Appendix C

Technical Support Fax Order

Name_________________________________________________________________
Company_____________________________________________________________
Address ______________________________________________________________
City ___________________ State/Province_______________________________
Zip/Postal Code ______________Count ry___________________ ____________
Phone_____________________________Fax _______________________________

Incident Summary

Model number of Allied Telesyn product I am using __________________
Firmware release number of Allied Telesyn product _________________
Other network software products I am using (e.g., network managers)

______________________________________________________________________
______________________________________________________________________
______________________________________________________________________

Brief summary of problem ___________________ ________________________

______________________________________________________________________
______________________________________________________________________

Conditions (List the steps that led up to the problem.)________________

______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________

______________________________________________________________________
Detailed description (Please use separate sheet)
Please also fax printouts of relevant files such as batch files and

configuration files. When completed, fax this s heet to the approp riate
Allied Telesyn office. Fax numbers can be found on page viii.

31

Appendix D

AT-FS909SX Installation Guide Feedback

Please tell us what additional information you would like to see
discussed in this guide. If there are topics you would like information
on that were not covered in this guide, please photocopy this page,
answer the questions and fax or mail this form back to Allied Telesyn.
The mailing address and fax number are at the bottom of the page.
Your comments are valuable when we plan future revisions of this
guide.

I found the following the most valuable _______________ ____________

_______________________________________________________________

_______________________________________________________________

_______________________________________________________________

_______________________________________________________________
I would like the following more developed ________________________

_______________________________________________________________

_______________________________________________________________

_______________________________________________________________

_______________________________________________________________
I would find this guide more useful if _____________________________

_______________________________________________________________

_______________________________________________________________

_______________________________________________________________
Please fax or mail your fee d back. Fax to 1-408-736-0100. Or mail to:

Allied Tele s yn In t ern ational, Corp .
c/o Technical Communications
960 Stewart Drive, Suite B
Sunnyvale, CA 94086 USA

PN 613-10846-00 Rev A

33