Allied Telesis AT-FS717FC/xx User Manual

AT-FS713FC/xx
AT-FS717FC/xx

10/100 Mbps Ethernet Switches

Installation Guide

PN 613-50268-00 Rev A

Copyright  2001 Allied Telesyn International Corp.
960 Stewart Drive Suite B, Sunnyvale CA 94085, USA

All rights reserved. No part of this publication may be reproduced without prior written permission
from Allied Telesyn International Corp.

Ethernet is a registered trademark of Xerox Corporation. All other product names, company names,
logos or other designations mentioned herein are trademarks or registered trademarks of their
respective own ers .

Allied Telesyn International Corp. reserves the right to make changes in specifications and other
information contained in this document witho ut prio r writte n noti ce. The infor mation prov id ed
herein is subject to change without notice. In no event shall Allied Telesyn International Corp. be
liable for any incidental, special, indirect, or consequential damages whatsoever, including but not
limited to lost profits, a rising out of or related to this manual or the information contai ned herein,
even if Allied Telesyn International Corp. has been advised of, known, or should have known, the
possibility of such damages.

Electrical Safety and Emission Compliance Statement

Standards: This product meets the following standards.

U.S. Federal Communications Commission

RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a Class A digital device
pursuant to Part 15 of F CC Rul e s. Th es e l im i t s are desi gn ed t o prov id e reas o n ab l e pr ot ec t ion against
harmful interference when th e eq uipment is operated in a commercia l environment. Th is equipment
generates, uses, and can rad iate radio frequency en ergy and, if not installed an d use d in acco r d an ce
with this instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Note: Modifications or changes not expressly approved of by the manufacturer or the FCC, can void
your right to operate this equipment.

Industry Canada

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel
brouilleur du Canada.

RFI Emission FCC Part 15 (Class A), EN55022 (Class A),

WARNING: In a domestic environment this product may cause radio interference in which case the user

may be required to take adequate measures.

Immunity EN55024
Electrica l Safety UL 1950 (UL/cUL), EN60950 (TUV), EN60825
Important: Appendix A contains translated safety statements for installing this equipment. When you

$

see the
Wichtig: Anhang A enthält übersetzte Sicherheitshinweise für die Installation dieses Geräts. Wenn Sie

$

Vigtigt: Tillæg A indeholder oversatte sikkerhedsadvarsler, der vedrører installation af dette udstyr. Når
De ser symbolet

Belangrijk: Appendix A bevat vertaalde veiligheidsopmerkingen voor het installeren van deze
apparatuur. Wannee r u de
taal.

Important: L'annexe A contient les instructions de sécurité relatives à l'installation de cet équipement.
Lorsque vous voyez le symbole
instructions dans votre langu e.

Tärkeää: Liite A sisältää tämän laitteen asentamiseen liittyvät käännetyt turvaohjeet. Kun näet
symbolin, katso käännettyä turvaohjetta liitteestä A.

Importante: l’Appendice A contiene avvisi di si cu rezza tradotti per l’installazione di questa
apparecchiatura. Il simbolo
lingua.

Viktig: Tillegg A inneholder oversatt sikkerhetsinformasjon for installering av dette utstyret. Når du ser

$

Importante: O Anexo A contém advertências de segurança traduzidas para instalar es te eq uipamento.
Quando vir o símbolo

Importante: El Apéndice A contiene mensajes de seguridad traducidos para la instalación de este equipo.
Cuando vea el símbolo

Obs! Bilaga A innehåller översatta säkerhetsmeddelanden avseende installationen av denna utrustning.
När du ser

, go to Appendix A for the translated safety statement in your language.

sehen, schlagen Sie in Anhang A den übersetzten Sicherheitshinweis in Ihrer Sprache nach.

$

, skal De sl å op i t illæ g A og f inde d e ove rsatt e si kker heds advars ler i Dere s ege t spr og.

$

ziet, raadpleeg Appendix A voor vertaalde veiligheidsinstructies in uw

$

$

, indica di consultare l’Appendice A per l’avviso di s icurezza nella pro pria

, åpner du til Tillegg A for å finne den oversatte sikkerhetsin fo rmasjonen på ønsket språk.

$

, leia a advertência de segurança traduzida no seu idioma no Ane xo A.

$

, vaya al Apéndice A para ver el mensaje de seguridad traducido a su idioma.

$

, skall du gå till Bilaga A för att läsa det öve rsatta säkerhetsmeddelandet på ditt språk.

EN61000-3-2, EN61000-3-3

$

2

$

3

$

1

$

, reportez-vous à l'annexe A pour consulter la traduction de ces

$

4

-

iii

Table of Contents

Electrical Safety and Emission Compliance Statement ......................iii

Welcome to Allied Telesyn .........................................................................vii

Where to Find Web-based Guides ...................................................................vii

Document Conventions ....................................................................................vii

Contacting Allied Telesyn Technical Support................................................viii

Online Support .........................................................................................viii

Telephone and Fax Support.....................................................................viii

Technical Support E-mail Addresses ........................................................ix

Returning Products ...........................................................................................ix

FTP Server.........................................................................................................ix

For Sales or Corporate Information .................................................................. x

Tell Us What You Think ....................................................................................x

Chapter 1

Overview ..........................................................................................................1

Features ..............................................................................................................4

Status LEDs ................................................................................................ 4

Twisted Pair Ports.............................................................................................. 5

Port Speed....................................................................................................5

Duplex Mode................................................................................................5

Auto MDI/MDI-X.........................................................................................5

Fiber Optic Port.................................................................................................. 6

Port Speed....................................................................................................6

Duplex Mode................................................................................................6

MAC Address Table............................................................................................ 7

Store and Forward..............................................................................................7

Network Topologies............................................................................................ 8

Workgroup Topology ...................................................................................8

Ethernet Hub Workgroup Topology ...........................................................9

Backbone Topology....................................................................................10

v

Table of Contents

Chapter 2

Installing the Switch ...................................................................................11

Reviewing Safety Guidelines ...........................................................................11

Verifying the Package Contents ......................................................................12

Planning the Installation.................................................................................13

Selecting a Site .................................................................................................14

Installing the Switch On a Table or Desktop..................................................15

Wall-mounting the Switch ...............................................................................16

Warranty Registration .....................................................................................17

Chapter 3

Troubleshooting ...........................................................................................19

Appendix A

Technical Specifications ............................................................................21

Physical .............................................................................................................21

Temperature .....................................................................................................21

Electrical Rating...............................................................................................21

Agency Certifications........................................................................................21

Fiber Optic Port Specifications ........................................................................22

Pinout Assignments..........................................................................................23

Appendix B

Translated Electrical Safety Emission Information ............................25

Appendix C

Technical Support Fax Order ...................................................................35

Incident Summary............................................................................................35

vi

Welcome to Allied Telesyn

The guide contains instructions on how to install the AT-FS713FC/xx and
AT-FS717FC/xx Series Ethernet Switches.

Where to Find Web-based Guides

The Allied Telesyn web site at www.alliedtelesyn.com provides you with an
easy way to access the most recent documentation, software, and technical
information for all of our products. For product guides, select “Support &
Services” from our web site.

Document Conventions

This guide uses several conventions that you should become familiar with
before you begin to install the product.

Note

A note provides additional information.

Caution

A caution indicates that performing or omitting a specific action may
result in equipment damage or loss of data.

Warning

A warning indicates that performing or omitting a specific action may
result in bodily injury.

vii

Contacting Allied Telesyn Technical Support

You can contact Allied Telesyn technical support online or by telephone, fax,
or e-mail.

Online Suppo rt

You can request technical support online by filling out the Technical Enquiry
Form or by accessing the Knowledge Base. You can use the Knowledge Base to
submit questions to our technical support staff and review answers to
previously asked questions.

To access the Knowledge Base, select “Support & Services”, then select “Help”
from www.alliedtelesyn.com. To access the Technical Enquiry Form, select
“Contact Us” from our web site.

Telephone and Fax Support

For technical support via fax, please fill out the “Technical Support Fax
Order” on page 35 and send it to the appropriate location listed below.

Americas

United States, Canada, Mexico,
Central America, South America
Tel: [phone], option 4
Fax: [phone]

Asia

Singapore, Taiwan, Thailand, Malaysia,
Indonesia, Korea, Philippines, China,
India, Hong Kong
Tel: [phone]
Fax: [phone]

Australia

Australia, New Zealand
Tel: [phone]
Fax: [phone]

France

France, Belgium, Luxembourg,
The Netherlands, Middle East, Africa
Tel: [phone]
Fax: [phone]

viii

Germany

Germany, Switzerland, Austria, Eastern
Europe
Tel: [phone]
Fax: [phone]

Italy

Italy, Spain, Portugal, Greece, Turkey,
Israel
Tel: [phone]
Fax: [phone]

Japan

Tel: [phone]
Fax: [phone]

United Kingdom

United Kingdom, Denmark, Norway,
Sweden, Finland, Iceland
Tel: [phone]
Fax: [phone]

AT-FS713FC/xx and AT-FS717FC/xx Series Installation Guide

Technical Support E-mail Addresses

United States and Canada

[e-mail]

Latin America, Mexico, Puerto Rico, Caribbean, and Virgin Islands

[e-mail]

Europe

[e-mail]

Returning Products

Products for return or repair must first be assigned a Return Materials
Authorization (RMA) number. A product sent to Allied Telesyn without a
RMA number will be returned to the sender at the sender’s expense.

To obtain an RMA number, contact Allied Telesyn’s Technical Support at one
of the following locations:

United States and Canada

Toll-free: 1-800-428-4835, option 4
Fax: [phone]

Latin America, Caribbean, and Virgin
Islands

Tel: International code + 425-481-3852
Fax: International code + 425-481-3895

Mexico

Toll-free: 800-424-5012, ext 3852
Fax: International code + 425-481-3895

Australia

Toll-free: 1-800-000-880
Fax: [phone]

Europe, Africa, and Middle East

Tel: [phone]
Fax: [phone]

Puerto Rico

Tel: [phone], ext 3852 or
1-800-424-4284, ext 3852

Asia and Southeast Asia

Tel: [phone]
Fax: [phone]

New Zealand

Toll-free: 0800-45-5782

FTP Server

If you need management software for an Allied Telesyn managed device and
you know the file name of the software, you can download the software by
connecting directly to our FTP server at ftp.alliedtelesyn.com. At login,
enter ‘anonymous’ as the user name and your e-mail address as the password.

ix

For Sales or Corporate Information

You can contact Allied Telesyn for sales or corporate information at the
location listed below:

Allied Telesyn International Corp.

19800 North Creek Parkway, Suite 200
Bothell, WA 98011
Tel: [phone]
Fax: [phone]

Tell Us What You Think

If you have any comments or suggestions on how we might improve this or
other Allied Telesyn documents, please fill out the General Enquiry Form
online. This form can be accessed by selecting “Contact Us” at
www.alliedtelesyn.com.

x

Chapter 1

Overview

The AT-FS713FC/xx and AT-FS717FC/xx Series Fast Ethernet Switches
include the following models:

q AT-FS713FC/FJ q AT-FS717FC/FJ
q AT-FS713FC/LC q AT-FS717FC/LC
q AT-FS713FC/MT q AT-FS717FC/MT
q AT-FS713FC/SC q AT-FS717FC/SC
q AT-FS713FC/ST q AT-FS717FC/ST
q AT-FS713FC/VF q AT-FS717FC/VF

These units are unmanaged Layer 2 switches. These switches can be used as a
‘bridge’ between the different workgroups in your network or they can be used
to create small workgroups with dedicated 10/100 Mbps links to your network
devices. They can also be used to connect to other Ethernet switches so that
they can be part of a larger Ethernet network.

The AT-FS713FC/xx Series Switches feature twelve 10/100Base-TX twisted
pair ports and a 100Base-FX fiber optic port. The twisted pair ports have a
RJ-45 connector and a maximum operating distance of 100 meters (328 feet).
The fiber optic port has a FJ, LC, MT, SC, ST, or VF connector, depending on
the model, and a maximum operating distance of 2 kilometers (1.2 miles).

The AT-FS717FC/xx Series Switches feature sixteen 10/100Base-TX twisted
pair ports and a 100Base-FX fiber optic port. The twisted pair ports have a
RJ-45 connector and a maximum operating distance of 100 meters (328 feet).
The fiber optic port has a FJ, LC, MT, SC, ST, or VF connector, depending on
the model, and a maximum operating distance of 2 kilometers (1.2 miles).

The fiber optic port operates at 100 Mbps and features half- and full-duplex
operation. The twisted pair port operates at 10 or 100 Mbps and auto­negotiates the duplex mode.

The AT-FS713FC/xx and AT-FS717FC/xx Series Switches are easy to install
and do not require software configuration or management.

1

Figure 1 illustrates the front and back panels of an AT-FS713FC/xx Series
Switch.

Front Panel

Duplex Switch

LEDs

AT-FS713FC/MT

10Base-T/100Base-TX 12 Port Fast Ethernet Switch with 100FX Uplink

100FX 10/100TX

LNK/
ACT

FD

1197531

121313 10 8 6 4 2

100FX

DUPLEX
HALF
FULL

LNK/
ACT

100M
LNK/

ACT

PWR

100M

Back Panel

1357911

24681012 13

120-240V 50-60Hz 0.5A

Power Plug

10/100Base-TX Ports

100Base-FX Port

Figure 1 AT-F S7 13 FC /x x Serie s Switc h (AT- FS 71 3F C/ MT Mod el)

Figure 2 illustrates the front and back panels of an AT-FS717FC/xx Series
Switch.

LEDs

100FX 10/100TX

111315 9 7 5 3 1

LNK/
ACT

FD

12141617 108642

LNK/
ACT

100M
LNK/

ACT

PWR

100M

Front Panel

AT-FS717FC/ST

10Base-T/100Base-TX 16 Port Fast Ethernet Switch with 100FX Uplink

Duplex Switch

100FX
DUPLEX

HALF
FULL

17

Back Panel

2

1357 9111315

TX RX

2 4 6 8 10 12 14 16

10/100Base-TX Ports

17

100Base-FX Ports

Figure 2 AT-FS717FC/xx Series Switch (AT- FS717FC/ST Model)

120-240V 50-60Hz 0.5A

Power Plug

AT-FS713FC/xx and AT-FS717FC/xx Series Installation Guide

Table 1 lists the maximum operating distances for the AT-FS713FC/xx Series
Switches.

Table 1 AT-FS713FC/xx Series Maximum Operating Distan ces

10/100Base-TX 100Base-FX

Model

Connector

Maximum
Operating Distance

Connector

Maximum
Operating Distance

AT-FS713FC/FJ RJ-45 100 m (328 ft) FJ 2 km (1.2 mi)
AT-FS713FC/LC RJ-45 100 m (328 ft) LC 2 km (1.2 mi)
AT-FS713FC/MT RJ-45 100 m (328 ft) MT 2 km (1.2 mi)
AT-FS713FC/SC R J-45 100 m (328 ft) SC 2 km (1.2 mi)
AT-FS713FC/ST RJ-45 100 m (328 ft) ST 2 km (1.2 mi)
AT-FS713FC/VF RJ-45 100 m (328 ft) VF 2 km (1.2 mi)

Table 2 lists the maximum operating distances for the AT-FS717FC/xx Series
Switches.

Table 2 AT-FS717FC/xx Series Maximum Operating Distan ces

10/100Base-TX 100Base-FX

Model

Connector

Maximum
Operating Distance

Connector

Maximum
Operating Distance

AT-FS717FC/FJ RJ-45 100 m (328 ft) FJ 2 km (1.2 mi)
AT-FS717FC/LC RJ-45 100 m (328 ft) LC 2 km (1.2 mi)
AT-FS717FC/MT RJ-45 100 m (328 ft) MT 2 km (1.2 mi)
AT-FS717FC/SC R J-45 100 m (328 ft) SC 2 km (1.2 mi)
AT-FS717FC/ST RJ-45 100 m (328 ft) ST 2 km (1.2 mi)
AT-FS713FC/VF RJ-45 100 m (328 ft) VF 2 km (1.2 mi)

3

Features

q LEDs for unit and port status
q Auto MDI/MDI-X for the twisted pair ports
q Half- or full-duplex operation on the fiber optic port
q Auto-negotiation of the duplex mode on the twisted pair ports
q RJ-45 twisted pair connectors
q FJ, LC, MT, SC, ST, or VF fiber optic connector
q Store and forward Ethernet packet handling
q MAC address table with a capacity of 4,000 addresses

Status LEDs

Table 3 defines the LEDs on the AT-FS713FC/xx and AT-FS717FC/xx Series
Switches.

Table 3 LEDs

LED Color Description

PWR Green The switch is receiving power.
FD Green

OFF

100M Green

OFF

LNK/ACT Green

Blinking Green
OFF

4

The fiber optic po rt is operating in full- duplex mode.
The fiber optic port is operating in half-duplex mode.

The twisted pair port is operating at 100 Mbps.
The twisted pair port is operating at 10 Mbps.

The port has established a valid link with the end-node
connected to the port.

Activity is detected on the port.
The port has not established a link wi th the end-node.

AT-FS713FC/xx and AT-FS717FC/xx Series Installation Guide

Twisted Pair Ports

The AT-FS713FC/xx and AT-FS717FC/xx Series Switches have twelve and
sixteen 10/100Base-TX twisted pair ports, respectively.

Port Speed

The twisted pair ports are compliant with the 10Base-T and 10Base-TX
standards and are capable of either 10 Mbps or 100 Mbps operation. The ports
are IEEE 802.3u auto-negotiation compliant. The speed of the port is set
automatically by the switch after determining the speed of the end-node
connected to the port. Auto-negotiation is designed to ensure that each port on
the switch and the end-node connected to each port are operating at the same
speed and that they are communicating at the highest possible common speed
of the devices.

Duplex Mode

The twisted pair ports on the switches can operated in either half- or full­duplex mode and are set automatically through auto-negotiation. If the end­node is capable of full-duplex mode, the twisted pair port is set to full-duplex.
If the end-node is capable of half-duplex mode, the port is set to half-duplex.

Auto MDI/MDI-X

An RJ-45 twisted pair port on a 10 Mbps or 100 Mbps Ethernet network
device can have one of two possible wiring configurations: MDI or MDI-X. The
RJ-45 port on a PC, router, or bridge is typically wired as MDI, while the
twisted pair port on a switch or hub is usually MDI-X.

To connect two 10 Mbps or 100 Mbps network devices together that have
dissimilar port wiring configurations, such as MDI to MDI-X, you would
usually use a straight-through twisted pair cable. To connect two network
devices that have the same wiring configuration, such as MDI to MDI, you
would usually use a crossover cable.

The AT-FS713FC/xx and AT-FS717FC/xx Series Switches feature automatic
MDI/MDI-X. Each port automatically determines the configuration of the port
on the device to which it is connected and then configures itself appropriately.
For example, if a port on a switch is connected to a port on a bridge, which is
typically wired as MDI, the port on the switch automatically configures itself
as MDI-X. This feature allows you to use either crossover cables or straight­through cables when connecting devices to these switches.

5

Fiber Optic Port

The AT-FS713FC/xx and AT-FS717FC/xx Series Switches have one
100Base-FX fiber optic port. The fiber optic port has a FJ, LC, MT, SC, ST, or
VF connector, depending on the model.

Port Speed

The fiber optic port is compliant with the 100Base-FX standard and has a
fixed operating speed of 100 Mbps. The end-node connected to the fiber optic
port on the switch must also be able to operate at 100 Mbps.

Duplex Mode

Duplex mode refers to the way an end-node sends and receives data on the
network. An end-node can operate in either half- or full-duplex mode,
depending on its capabilities. An end-node that is operating in half-duplex
mode can either send data or receive data, but it cannot do both at the same
time. An end-node that is operating in full-duplex mode can send and receive
data simultaneously. The best network performance is achieved when an end­node can operate at full-duplex, since the end-node is able to send and receive
data simultaneously.

The AT-FS713FC/xx and AT-FS717FC/xx Series Switches can operate in
either half- or full-duplex mode. To set the duplex mode on the fiber optic port,
slide the 100FX DUPLEX switch UP (half-duplex) or DOWN (full-duplex). The
switch can operate with end-nodes capable of either half-duplex mode or full­duplex mode.

6

AT-FS713FC/xx and AT-FS717FC/xx Series Installation Guide

MAC Address Table

Up to 4,000 MAC addresses can be stored in the switch’s MAC address table.
The switch’s self-learning feature will learn all new addresses in real-time
after power-up. If the source address of an incoming packet is not found in the
MAC address table, the switch will update the table with the new address.

The switch also has an automatic address aging feature that will delete a
source address from the table if it has not seen a frame from the end-node
with that address within five minutes. This prevents the table from becoming
filled with addresses of end-nodes that are no longer active.

The switch forwards all multicast, broadcast, and unicast packets when the
MAC address table has exceeded its storage limit.

Store and Forward

The AT-FS713FC/xx and AT-FS717FC/xx Series Switches support store and
forward switching at Fast Ethernet full-wire speed in 100 Mbps, half- or full­duplex mode. Packets entering each port are stored in buffers. Once the full
packet is received, the switch will forward or discard the packet, depending on
its destination address and error status. This ensures that only error-free
packets destined for another segment will be transferred across the switch,
reducing network load. For example, if the packet entering from Port 1 is
destined for an end-node on Port 2, the switch forwards the frame if the frame
does not contain any errors. If the packet from Port 1 is destined for an end­node also connected to Port 1, the packet is discarded.

The switch will discard CRC errors, misaligned, runt, and under-oversized
packets. When the packet has dribble bits at the end, the switch will truncate
to octet boundary and check for a good FCS before forwarding.

7

Network Topologies

The AT-FS713FC/xx or AT-FS717FC/xx Series Switches can be used in
several network topologies. Some of these topologies are described below.

Workgroup Topology

Figure 3 illustrates a workgroup topology where each end-node is connected
directly to a port on an AT-FS713FC/SC switch, giving each end-node a
dedicated 10 Mbps or 100 Mbps link.

AT-FS713FC/SC

1357911

TX RX

24681012 13

Figure 3 Power Workgroup Topology

120-240V 50-60Hz 0.5A

10 Mbps
100 Mbps

8

AT-FS713FC/xx and AT-FS717FC/xx Series Installation Guide

Ethernet Hub Workgroup Topology

Figure 4 illustrates an Ethernet hub workgroup topology where an
AT-FS713FC/SC is used to connect together four 10/100 Mbps Ethernet hubs.
This allows the switch to function as a bridge between the different
workgroups by controlling the flow of data between the workgroups. The
switch transfers an Ethernet frame from hub-to-hub only when the
destination end-node for the frame is on a different hub than the end-node
that originated the frame. This reduces the amount of unnecessary data traffic
in each workgroup. This frees up bandwidth and improves network
performance.

AT-FS713FC/SC

1357911

24681012 13

TX RX

120-240V 50-60Hz 0.5A

Ethernet Hub

8

7

2

1

6

54

3

Ethernet Hub Ethernet Hub

8

7

2

54

1

3

6

10 Mbps

100 Mbps

Figure 4 Ethernet H ub Workgroup Topology

Ethernet Hub

8

7

6

54

3

8

7

6

54

2

1

2

1

3

9

Backbone Topology

If your network consists of several AT-FS713FC/xx or AT-FS717FC/xx Series
Switches, then you will probably want to connect them together to form an
integrated network. Here the fiber optic ports can be extremely useful. You
can use the ports to create a fiber optic backbone. With a maximum operating
distance of 2 kilometers (1.2 miles), the ports can be used to connect together
switches that are physically far apart. Figure 5 shows an AT-FS713FC/ST
switch and an AT-FS717FC/ST switch interconnected using the fiber optic
ports to create a backbone topology.

AT-FS713FC/ST

1357911

2 4 6 8 10 12 13

TX RX

AT-FS717FC/SC

1357 9111315

2468 10121416

120-240V 50-60Hz 0.5A

TX RX

17

120-240V 50-60Hz 0.5A

100 Mbps (Fiber Optic)
100 Mbps (Twisted Pair)
10 Mbps

10

Figure 5 Backbone Topology

Chapter 2

Installing the Switch

This chapter contains desktop and wall-mounting installation instructions for
an AT-FS713FC/xx or AT-FS717FC/xx Series Switch.

Reviewing Safety Guidelines

Please review the following safety guidelines before you begin to install the
switch.

Warning

Class 1 laser product. $ 5

Warning

Do not stare into the laser beam. $ 6

Warning
Electric Shock Hazard: To prevent electric shock, do not remove the

cover. There are no user-serviceable parts inside. The unit contains
hazardous voltages and should only be opened by a trained and
qualified technician. $ 7

Warning
Lightning Danger: Do not work on this equipment or cables during

periods of lightening activity. $ 8

Warning
Power cord is used as a disconnection device: To de-energize

equipment, disconnect the power cord. $ 9

11

Caution
Pluggable Equipment: The socket outlet should be installed near the

equipment and should be easily accessible. $ 10

Caution
Air vents: The air vents must not be blocked on the unit and must have

free access to the room ambient air for cooling. $ 11

Caution
Operating Temperature: This product is designed for a maximum

ambient temperature of 40°C. $ 12

Caution
All Countries: Install this product in accordance with local and

National Electric Codes. $ 13

Verifying the Package Contents

Make sure the following items are included in your package. If any item is
missing or damaged, contact your Allied Telesyn sales representative for
assistance.

q One AT-FS713FC/xx or AT-FS717FC/xx Series Switch

q Power cord

q Four protective feet (for desktop use only)

q This installation guide

q Warranty card

12

AT-FS713FC/xx and AT-FS717FC/xx Series Installation Guide

Planning the Installation

Be sure to observe the following guidelines when planning the installation of
your switch.

q The end-node connected to the 100Base-FX fiber optic port must be

able to operate at 100 Mbps.

q The end-node connected to a 10/100Base-TX twisted pair port must be

able to operate at 10 or 100 Mbps.

q The end-node connected to a port on the switch can be a network

adapter card, repeater, router, hub, or another switch.

q Refer to Table 4 for the cabling specifications for the twisted pair

ports.

Table 4 10/100Base-TX Twisted Pair Cabling Specifications

Operating Mode Twisted Pair Cable

10Base-T Shielded or unshielded Category 3 or be tter 100 m (328 ft)
100Base-TX Shielded or uns hie l de d Ca te go r y 5 or bette r 100 m (328 ft)

q Refer to Table 5 for the cabling specifications for the fiber optic port

operating in full-duplex mode.

Table 5 100Base-FX Fiber Optic Cabl ing Specifications (Full-d uplex)

Model Fiber Optic Cable

All models 50/125 or 62.5/125

micron multimode

Note

Refer to “Fiber Optic Port Specifications” on page 22 for additional
information on the fiber optic port.

Maximum Operating
Distance

2 km (1.2 mi) 13 dB at 1310 nm

Maximum Operating
Distance

Maximum
Allowable Lo ss
Budget

13

q Refer to Table 6 for the cabling specifications for the fiber optic port

operating in half-duplex mode.

1

Number of Media
Converters

Table 6 100Base-FX Fiber Optic Ports (Half-duplex)

Connected Device s

Maximum Operating
Distance

One Media Converter Inline Switch to switch 372 m (1,221 ft)

Workstation to switch 372 m (1,221 ft)
Switch to Class I repeater 137 m (450 ft)
Switch to Class II repeater 18 5 m (607 ft)

Two Media Converters

Switch to switch 332 m (1,089 ft)

Inline

Workstation to switch 322 m (1, 089 ft)
Switch to Class I repeater 97 m (318 ft)
Switch to Class II repeater 14 5 m (476 ft)

1. The total distance of the fiber optic port lengths cannot exceed the limits stated in the table. Each media converter
used inline within a single collision domain reduces the overall segment length by 40 meters (131 feet).

Selecting a Site

Be sure to observe the following guidelines when selecting a site for your
switch.

q Select a site that is dust-free and moisture-free.

q Select a site that will allow you to easily access the data cables and

power cord.

q Make sure the air flow around the switch and through its vents on the

side and back are not restricted.

q For use on a desktop, make sure the desktop is level and secure.

q Use dedicated power circuits or power conditioners to supply reliable

power to the device.

q Keep the twisted pair cabling away from sources of electrical noise,

such as radios, transmitters, power lines, broadband amplifiers,
electrical motor, and fluorescent fixtures.

14

AT-FS713FC/xx and AT-FS717FC/xx Series Installation Guide

Installing the Switch On a Table or Desktop

To wall-mount the switch, refer to “Wall-mounting the Switch” on page 16. To
install the switch on a table or desktop, perform the following procedure:

1. Remove all components from the shipping package and store the

packaging material in a safe location.

Note

Do not remove the dust covers from the fiber optic port until you are
ready to connect the fiber optic cable. Dust contamination can adversely
impact the operating performance of the port and the switch.

2. Attach the four protective feet (provided) to each corner of the base of the

unit.

3. Connect the twisted pair cables to the RJ-45 connectors.

4. Remove the dust cover from the fiber optic port and connect the fiber optic

cable to the port.

5. Set the 100FX DUPLEX switch on the fiber optic port to either HALF for

half-duplex or FULL for full-duplex operation. The capabilities of the end­node connected to the fiber optic port will determine the correct setting for
this switch. If the end-node is capable of only half-duplex, set the switch to
HALF. If the end-node is capable of full-duplex, set the switch to FULL.

Caution
Power cord is used as a disconnection device: To de-energize

equipment, disconnect the power cord. $ 10

6. Power ON the switch by plugging one end of the power cord to the back of

the switch and the other end of the power cord to a power outlet. The PWR
LED should be green. If the LED is OFF, refer to “Troubleshooting” on
page 19 for assistance.

7. Power ON the end-nodes connected to the ports on the switch.

8. Check the LNK/ACT LED for each port. The LED should be green or

blinking. If the LED is OFF, refer to “Troubleshooting” on page 19 for
assistance.

The switch is now ready for use.

15

Wall-mounting the Switch

The switch can be mounted either vertically or horizontally on a wall using
the keyholes on the bottom of the chassis. For wall-mount installation, you
will need two panhead screws and plastic anchors.

To wall-mount the switch, perform the following procedure:

1. If attached, remove the rubber feet, data cables, and power cord from the

switch.

2. Select a wall location for the device.

3. Install the plastic anchors and panhead screws 100 millimeters (3.94

inches) apart on the wall.

4. Position the device onto the wall screws. If you are mounting the switch

horizontally, position the switch so that the ports are facing down and the
LEDs are facing up. If you are mounting the switch vertically, position the
switch so that the ports are facing to the left and the LEDs to the right.

5. Connect the twisted pair cables to the RJ-45 connectors.

6. Connect the fiber optic cable to the fiber optic port.

7. Set the 100FX DUPLEX switch on the fiber optic port to either HALF for

half-duplex or FULL for full-duplex operation. The capabilities of the end­node connected to the fiber optic port will determine the correct setting for
this switch. If the end-node is capable of only half-duplex, set the switch to
HALF. If the end-node is capable of full-duplex, set the switch to FULL.

Warning

The power cord is used as a disconnection device. To de-energize
equipment, disconnect the power cord. $9

8. Power ON the switch by plugging one end of the power cord to the back of

the switch and the other end of the power cord to a power outlet. The PWR
LED should be green. If the LED is OFF, refer to “Troubleshooting” on
page 19 for assistance.

9. Power ON the end-nodes connected to the ports on the switch.

10. Check the LNK/ACT LED for each port. The LED should be green or

blinking. If the LED is OFF, refer to “Troubleshooting” on page 19 for
assistance.

The switch is now ready for use.

16

AT-FS713FC/xx and AT-FS717FC/xx Series Installation Guide

Warranty Registration

When you have finished installing the product, register your product by
completing the enclosed warranty card and sending it in. You can also fill out
the registration online by selecting “Warranties” under “Support & Services”
from www.alliedtelesyn.com.

17

Chapter 3

Troubleshooting

Follow the guidelines below to test and troubleshoot the installation in the
event a problem occurs.

If the PWR LED is OFF, do the following:

q Make sure that the power cord is securely connected to the wall outlet

and the power connector on the back of the switch.

q Verify that the power outlet has power by connecting another device

to it.

q Try connecting the switch to another power source.

q Try using another power cord.

If a LNK/ACT LED for a twisted pair port is OFF, do the following:

q Check that the end-node connected to the port is powered ON and is

operating properly.

q Check that the twisted pair cable is securely connected to the port on

the switch and to the port on the end-node.

q Verify that the end-node is operating at 10 or 100 Mbps and half-

duplex mode.

q Make sure that the twisted pair cable does not exceed 100 meters (328

feet) and that you are using a Category 3 or better cable for 10Base-T
operation or a Category 5 or better cable for 100Base-TX operation.

19

If the LNK/ACT LED for the fiber optic port is OFF, do the following:

q Verify that the end-node connected to the port is ON and is operating

properly.

q Check that the fiber optic cable is securely connected to the port on the

switch and to the port on the end-node.

q Check to be sure that the end-node connected to the port is operating

at 100 Mbps.

q Make sure that the cable connected to the fiber optic receiver port on

the switch is connected to the transmitter port on the end-node and
that the fiber optic transmitter port on the switch is connected to the
receiver port on the end-node.

q Test the attenuation on the fiber cable to ensure that it does not

exceed acceptable values.

q Verify that you are using the appropriate type of fiber optic cabling

and that you have not exceeded the maximum operating distance. For
cable types and operating distance, refer to Table 1 and Table 2 on
page 3.

q Make sure that the 100FX DUPLEX switch is set correctly. The switch

should be set to match the duplex mode of the end-node connected to
the fiber optic port.

q Check that the operating specifications (e.g., wavelength and

maximum operating distance) of the fiber optic port on the end-node
are compatible with the operating specifications of the fiber optic port
on the switch. See “Fiber Optic Port Specifications” on page 22 for
additional information on the fiber optic port.

If you are still experiencing problems after testing and troubleshooting the
installation, contact Allied Telesyn Technical Support for assistance. Refer to
“Contacting Allied Telesyn Technical Support” on page viii or visit our web
site at www.alliedtelesyn.com for support information.

20

Appendix A

Technical Specifications

Physical

Dimensions: W x D x H

1.7 cm x 17.9 cm x 9.8 cm (0.7 in x 7 in x 3.9 in)

Weight: 0.42 kg (0.9 lbs)

Temperature

Maximum Operating: 0° to 40° C (32° to 104° F)

Maximum Storage: -25° to 70° C (-13° to 158° F)

Relative Humidity: 5% to 95% non-condensing

Operating Altitude: Up to 3,000 meters (9,843 feet)

Electrical Rating

Input Supply Voltage: 100-240 V AC

Maximum Current: 0.5 A

Power Consumption: 8 watts

Agency Certifications

Safety: UL/cUL, TUV

Standard: UL1950, EN60950

Immunity: EN55024

EMI/RFI: FCC Part 15 (Class A), EN55022 (Class A),

EN61000-3-2, EN61000-3-3

21

Fiber Optic Port Specifications

Table 7 through Table 10 list the specifications for the fiber optic port.

Table 7 Fiber Optic Transmi tter

Model Fiber Type

Fiber
Optic
Diameter
(microns)

Optical
Frequency

Launch Power (dBm)

Maximum Average Minimum

All models Multimode 50/125 1310 nm -14.0 -20.3 -22.5

Multimode 62.5/125 1310 nm -14.0 -16.8 -19.0

1. The launch power is measured at one meter from th e t r ansmitter.

Table 8 Fiber Optic Receiver

Model Fiber Type

Fiber
Optic
Diameter
(microns)

Optical
Frequency

Receiver Power (dBm)

Minimum Average Saturation

All models Multimode 50/125 1310 nm -31.8 -34.5 -14.0

Multimode 62.5/125 1310 nm -31.8 -34.5 -14.0

Table 9 Fiber Optic Dat alink

Model

Fiber
Type

Minimum
Power/Link
Budget

Average
Signal
Loss (dB)

Minimum
Distance
Specs.

1

Maximum
Distance
Specs.

1

All models 50/125

13.00 18.70 0 2 km (1.2 mi)

Multimode

62.5/125

16.80 22.50 0 2 km (1.2 mi)

Multimode

1. The recommended minimum range is stated in all cases where the maximum transmitter output
power excee ds the receivers saturati o n level. Thi s is to prevent blindi ng or burning out of the o ptical
receiver on the far end-node.

22

AT-FS713FC/xx and AT-FS717FC/xx Series Installation Guide

Table 10 Fiber Optic Loss Specification (Benchmark)

Fiber Type

Fiber Optic
Diameter

Multimode 50/125

Optical
Frequency

Typical Loss
Factor

Worst Case
Loss Factor

Bandwidth

1310 nm 1.00 dB/km 1.50 dB/km 400 Mhz-km

microns

62.5/125

1310 nm 1.00 dB/km 1.50 dB/km 500 Mhz-km

microns

Pinout Assignments

Figure 6 shows the pin assignments of the RJ-45 connector.

Pin 1 Pin 8

Figure 6 RJ-45 Pin Assignments

Table 11 lists the 10/100Base-TX connector pins and their signals when the
port is operating in either MDI or MDI-X configuration.

Table 11 RJ-45 Pinouts

MDI-X (Defaul t) Signal MDI Signal

1 RX+ 1 TX+
2 RX- 2 TX­3TX+3 RX+
4- 4 ­5- 5 ­6TX-6 RX­7- 7 ­8- 8 -

23

Appendix B

Translated Electrical Safety Emission Information

Important: This appendix contains multiple-language translations for the
safety statements in this guide.

Wichtig: Dieser Anhang enthält Übersetzungen der in diesem Handbuch
enthaltenen Sicherheitshinweise in mehreren Sprachen.

Vigtigt: Dette tillæg indeholder oversættelser i flere sprog af
sikkerhedsadvarslerne i denne håndbog.

Belangrijk: Deze appendix bevat vertalingen in meerdere talen van de
veiligheidsopmerkingen in deze gids.

Important: Cette annexe contient la traduction en plusieurs langues des
instructions de sécurité figurant dans ce guide.

Tärkeää: Tämä liite sisältää tässä oppaassa esiintyvät turvaohjeet usealla
kielellä.

Importante: questa appendice contiene traduzioni in più lingue degli avvisi di
sicurezza di questa guida.

Viktig: Dette tillegget inneholder oversettelser til flere språk av
sikkerhetsinformasjonen i denne veiledningen.

Importante: Este anexo contém traduções em vários idiomas das advertências
de segurança neste guia.

Importante: Este apéndice contiene traducciones en múltiples idiomas de los
mensajes de seguridad incluidos en esta guía.

Obs! Denna bilaga innehåller flerspråkiga översättningar av
säkerhetsmeddelandena i denna handledning.

25

Standards: This product meets the following standards.

U.S. Federal Communications Commission

RADIATED ENERGY
Note: This equipment has been tested and found to comply with the limits for a Class A
digital device pursuant to Part 15 of FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with this instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
Note: Modifications or changes not expressly approved of by the manufacturer or the
FCC, can void your right to operate this equipment.

Industry Canada

This Class A digital apparatus meets all requirements of the Canadian Interference­Causing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.

$

1 RFI Emission FCC Part 15 (Class A), EN55022 (Class A),

$

2 Warning: In a domestic environment this product may cause radio interference in

$

3 Immunity EN55024

$

4 Electrical Safety UL 1950 (UL/cUL), EN60950 (TUV), EN60825

which case the user may be required to take adequate measures.

EN61000-3-2, EN61000-3-3

$

5 Warning: Class 1 Laser product.

$

6 Warning: Do not stare into the laser beam.

$

7 ELECTRICAL NOTICES

$

8 LIGHTNING DANGER

$

9 Caution: POWER CORD IS USED AS A DISCONNECTION DEVICE. TO DE-

$

10 PLUGGABLE EQUIPMENT, the socket outlet shall be installed near the equipment

$

11 Caution: Air vents must not be blocked and must have free access to the room

$

12 Operating Temperature: This product is designed for a maximum ambient

Warning: ELECTRIC SHOCK HAZARD

To prevent ELECTRIC shock, do not remove the cover. No user-serviceable parts
inside. This unit contains HAZARDOUS VOLTAGES and should only be opened by a
trained and qualified technician. To avoid the possibility of ELECTRIC SHOCK,
disconnect electric power to the product before connecting or disconnecting the LAN
cables.

Danger: DO NOT WORK on equipment or CABLES during periods of LIGHTNING
ACTIVITY.

ENERGIZE EQUIPMENT, disconnect the power cord.

and shall be easily accessible.

ambient air for cooling.

temperature of 40° degrees C.

26

AT-FS713FC/xx and AT-FS717FC/xx Series Installation Guide

$

13 All Countries: Install product in accordance with local and National Electrical Codes.

Normen: Dieses Produkt erfüllt die Anforderungen der nachfolgenden Normen.

$

1 Hochfrequenzstörung FCC Part 15 (Class A), EN55022 (Class A),

$

2 Warnung: Bei Verwendung zu Hause kann dieses Produkt Funkstörungen

$

3 Störsicherheit EN55024

$

4 Elektrische Sicherheit UL 1950 (UL/cUL), EN60950 (TUV), EN60825

$

5 WARNUNG: Laserprodukt der Klasse 1.

$

6 Warnung: Nicht direkt in den Strahl blicken.

$

7 Achtung: GEFÄHRLICHE SPANNUNG

$

8 GEFAHR DURCH BLITZSCHLAG

$

9 Vorsicht: DAS NETZKABEL DIENT ZUM TRENNEN DER STROMVERSORGUNG.

$

10 STECKBARES GERÄT: Die Anschlußbuchse sollte in der Nähe der Einrichtung

hervorrufen. In diesem Fall müßte der Anwender angemessene Gegenmaßnahmen
ergreifen.

Das Gehäuse nicht öffnen. Das Gerät enthält keine vom Benutzer wartbaren Teile.
Das Gerät steht unter Hochspannung und darf nur von qualifiziertem technischem
Personal geöffnet werden. Vor Anschluß der LAN-Kabel, Gerät vom Netz trennen.

Gefahr: Keine Arbeiten am Gerät oder an den Kabeln während eines Gewitters
ausführen.

ZUR TRENNUNG VOM NETZ, KABEL AUS DER STECKDOSE ZIEHEN.

angebracht werden und leicht zugänglich sein."

EN61000-3-2, EN61000-3-3

$

11 Vorsicht: Die Entlüftungsöffnungen dürfen nicht versperrt sein und müssen zum

$

12 Betriebstemperatur: Dieses Produkt wurde für den Betrieb in einer

$

13 Alle Länder: Installation muß örtlichen und nationalen elektrischen Vorschriften

$

1 Radiofrekvens

$

2 Advarsel: I et hjemligt miljø kunne dette produkt forårsage radio forstyrrelse. Bliver

$

3 Immunitet EN55024

$

4 Elektrisk sikkerhed UL 1950 (UL/cUL), EN60950 (TUV), EN60825

$

5 Advarsel Laserprodukt av klasse 1.

$

6 Advarsel Stirr ikke på strålen.

Kühlen freien Zugang zur Raumluft haben.

Umgebungstemperatur von nicht mehr als 40° C entworfen.

entsprechen.

Standarder: Dette produkt tilfredsstiller de følgende standarder.

forstyrrelsesemission FCC Part 15 (Class A), EN55022 (Class A),

EN61000-3-2, EN61000-3-3

det tilfældet, påkræves brugeren muligvis at tage tilstrækkelige foranstaltninger.

27

$

7 ELEKTRISKE FORHOLDSREGLER

$

8 FARE UNDER UVEJR

$

9 Advarsel: DEN STRØMFØRENDE LEDNING BRUGES TIL AT AFBRYDE

$

10 UDSTYR TIL STIKKONTAKT, stikkontakten bør installeres nær ved udstyret og skal

$

11 Advarsel: Ventilationsåbninger må ikke blokeres og skal have fri adgang til den

$

12 Betjeningstemperatur: Dette apparat er konstrueret til en omgivende temperatur

$

13 Alle Lande: Installation af produktet skal ske i overensstemmelse med lokal og

$

1 RFI Emissie FCC Part 15 (Class A), EN55022 (Class A),

$

2 Waarschuwing: Binnenshuis kan dit product radiostoring veroorzaken, in welk geval

Advarsel: RISIKO FOR ELEKTRISK STØD For at forebygge ELEKTRISK stød,

undlad at åbne apparatet. Der er ingen indre dele, der kan repareres af brugeren.
Denne enhed indeholder LIVSFARLIGE STRØMSPÆNDINGER og bør kun åbnes af
en uddannet og kvalificeret tekniker. For at undgå risiko for ELEKTRISK STØD,
afbrydes den elektriske strøm til produktet, før LAN-kablerne monteres eller
afmonteres.

Fare: UNDLAD at arbejde på udstyr eller KABLER i perioder med LYNAKTIVITET.

STRØMMEN. SKAL STRØMMEN TIL APPARATET AFBRYDES, tages ledningen
ud af stikket.

være lettilgængelig.

omgivende luft i rummet for afkøling.

på maksimum 40 grader C.

national lovgivning for elektriske installationer.

Eisen: Dit product voldoet aan de volgende eisen.

EN61000-3-2, EN61000-3-3

de gebruiker verplicht kan worden om gepaste maatregelen te nemen.

$

3 Immuniteit EN55024

$

4 Electrische Veiligheid UL 1950 (UL/cUL), EN60950 (TUV), EN60825

$

5 Waarshuwing Klasse-1 laser produkt.

$

6 Waarchuwing Neit in de straal staren.

$

7 WAARSCHUWINGEN MET BETREKKING TOT ELEKTRICITEIT

$

8 GEVAAR VOOR BLIKSEMINSLAG

$

9 Waarschuwing: HET TOESTEL WORDT UITGESCHAKELD DOOR DE

$

10 AAN TE SLUITEN APPARATUUR, de contactdoos wordt in de nabijheid van de

Waarschuwing: GEVAAR VOOR ELEKTRISCHE SCHOKKEN
Verwijder het deksel niet, teneinde ELEKTRISCHE schokken te voorkomen. Binnenin
bevinden zich geen onderdelen die door de gebruiker onderhouden kunnen worden. Dit
toestel staat onder GEVAARLIJKE SPANNING en mag alleen worden geopend door
een daartoe opgeleide en bevoegde technicus. Om het gevaar op ELEKTRISCHE
SCHOKKEN te vermijden, moet u het toestel van de stroombron ontkoppelen alvorens
de LAN-kabels te koppelen of ontkoppelen.

Gevaar: NIET aan toestellen of KABELS WERKEN bij BLIKSEM.

STROOMKABEL TE ONTKOPPELEN.OM HET TOESTEL STROOMLOOS TE
MAKEN: de stroomkabel ontkoppelen.

apparatuur geïnstalleerd en is gemakkelijk te bereiken."

28

AT-FS713FC/xx and AT-FS717FC/xx Series Installation Guide

$

11 Opgelet: De ventilatiegaten mogen niet worden gesperd en moeten de omgevingslucht

$

12 Bedrijfstemperatuur: De omgevingstemperatuur voor dit produkt mag niet meer

$

13 Alle Landen: het toestel installeren overeenkomstig de lokale en nationale

$

1 Emission d’interférences

$

2 Mise En Garde : dans un environnement domestique, ce produit peut provoquer des

$

3 Immunité EN55024

$

4 Sécurité électrique UL 1950 (UL/cUL), EN60950 (TUV), EN60825

$

5 Attention Producit laser di classe 1.

$

6 Attention Ne pas fixer le faisceau des yeux.

$

7 INFORMATION SUR LES RISQUES ÉLECTRIQUES

ongehinderd toelaten voor afkoeling.

bedragen dan 40 graden Celsius.

elektrische voorschriften.

Normes: ce produit est conforme aux normes de suivantes:

radioélectriques FCC Part 15 (Class A), EN55022 (Class A),

interférences radioélectriques. Auquel cas, l’utilisateur devra prendre les mesures
adéquates.

Avertissement: DANGER D’ÉLECTROCUTION
Pour éviter toute ÉLECTROCUTION, ne pas ôter le revêtement protecteur du
matériel. Ce matériel ne contient aucun élément réparable par l’utilisateur. Il
comprend des TENSIONS DANGEREUSES et ne doit être ouvert que par un
technicien dûment qualifié. Pour éviter tout risque d’ÉLECTROCUTION, débrancher
le matériel avant de connecter ou de déconnecter les câbles LAN.

EN61000-3-2, EN61000-3-3

$

8 DANGER DE FOUDRE

$

9 Attention: LE CORDON D’ALIMENTATION SERT DE MISE HORS CIRCUIT.

$

10 EQUIPEMENT POUR BRANCHEMENT ELECTRIQUE, la prise de sortie doit être

$

11 Attention: Ne pas bloquer les fentes d’aération, ceci empêcherait l’air ambiant de

$

12 Température De Fonctionnement: Ce matériel est capable de tolérer une

$

13 Pour Tous Pays: Installer le matériel conformément aux normes électriques

Danger: NE PAS MANIER le matériel ou les CÂBLES lors d’activité orageuse.

POUR COUPER L’ALIMENTATION DU MATÉRIEL, débrancher le cordon.

placée près de l’équipement et facilement accessible".

circuler librement pour le refroidissement.

température ambiante maximum de ou 40 degrés Celsius.

nationales et locales.

29

Standardit: Tämä tuote on seuraavien standardien mukainen.

$

1 Radioaaltojen häirintä FCC Part 15 (Class A), EN55022 (Class A),

$

2 Varoitus: Kotiolosuhteissa tämä laite voi aiheuttaa radioaaltojen häiröitä, missä

$

3 Kestävyys EN55024

$

4 Sähköturvallisuus UL 1950 (UL/cUL), EN60950 (TUV), EN60825

$

5 VAROITUS Luokan 1 Lasertuote.

$

6 Variotus Älä katso säteeseen.

$

7 SÄHKÖÖN LIITTYVIÄ HUOMAUTUKSIA

$

8 SALAMANISKUVAARA

$

9 Huomautus: VIRTAJOHTOA KÄYTETÄÄN VIRRANKATKAISULAITTEENA.

$

10 PISTORASIAAN KYTKETTÄVÄ LAITE; pistorasia on asennettava laitteen lähelle ja

$

11 Huomautus: Ilmavaihtoreikiä ei pidä tukkia ja niillä täytyy olla vapaa yhteys

tapauksessa laitteen käyttäjän on mahdollisesti ryhdyttävä tarpeellisiin
toimenpiteisiin.

Varoitus: SÄHKÖISKUVAARA
Estääksesi SÄHKÖISKUN älä poista kantta. Sisällä ei ole käyttäjän huollettavissa
olevia osia. Tämä laite sisältää VAARALLISIA JÄNNITTEITÄ ja sen voi avata vain
koulutettu ja pätevä teknikko. Välttääksesi SÄHKÖISKUN mahdollisuuden katkaise
sähkövirta tuotteeseen ennen kuin liität tai irrotat paikallisverkon (LAN) kaapelit.

Hengenvaara: ÄLÄ TYÖSKENTELE laitteiden tai KAAPELEIDEN KANSSA
SALAMOINNIN AIKANA.

VIRTA KATKAISTAAN irrottamalla virtajohto.

siihen on oltava esteetön pääsy."

ympäröivään huoneilmaan, jotta ilmanvaihto tapahtuisi.

EN61000-3-2, EN61000-3-3

$

12 Käyttölämpötila: Tämä tuote on suunniteltu ympäröivän ilman maksimilämpötilalle

$

13 Kaikki Maat: Asenna tuote paikallisten ja kansallisten sähköturvallisuusmääräysten

$

1 Emissione RFI (interferenza

$

2 Avvertenza: in ambiente domestico questo prodotto potrebbe causare radio

$

3 Immunità EN55024

$

4 Sicurezza elettrica UL 1950 (UL/cUL), EN60950 (TUV), EN60825

$

5 AVVERTENZA Prodotto laser di Classe 1.

$

6 Avertenza Non fissare il raggio con gli occhi.

40°C.

mukaisesti.

Standard: Questo prodotto è conforme ai seguenti standard.

di radiofrequenza) FCC Part 15 (Class A), EN55022 (Class A),

EN61000-3-2, EN61000-3-3

interferenza. In questo caso potrebbe richiedersi all’utente di prendere gli adeguati
provvedimenti.

30

AT-FS713FC/xx and AT-FS717FC/xx Series Installation Guide

$

7 AVVERTENZE ELETTRICHE

$

8 PERICOLO DI FULMINI

$

9 Attenzione: IL CAVO DI ALIMENTAZIONE È USATO COME DISPOSITIVO DI

$

10 APPARECCHIATURA COLLEGABILE, la presa va installata vicino all’apparecchio

$

11 Attenzione: le prese d’aria non vanno ostruite e devono consentire il libero ricircolo

$

12 Temperatura Di Funzionamento: Questo prodotto è concepito per una temperatura

$

13 Tutti I Paesi: installare il prodotto in conformità delle vigenti normative elettriche

$

1 RFI stråling FCC Part 15 (Class A), EN55022 (Class A),

Attenzione: PERICOLO DI SCOSSE ELETTRICHE Per evitare SCOSSE
ELETTRICHE non asportare il coperchio. Le componenti interne non sono riparabili
dall’utente. Questa unità ha TENSIONI PERICOLOSE e va aperta solamente da un
tecnico specializzato e qualificato. Per evitare ogni possibilità di SCOSSE
ELETTRICHE, interrompere l’alimentazione del dispositivo prima di collegare o
staccare i cavi LAN.

Pericolo: NON LAVORARE sul dispositivo o sui CAVI durante PRECIPITAZIONI
TEMPORALESCHE.

DISATTIVAZIONE. PER TOGLIERE LA CORRENTE AL DISPOSITIVO staccare il
cavo di alimentazione.

per risultare facilmente accessibile".

dell’aria ambiente per il raffreddamento.

ambientale massima di 40 gradi centigradi.

nazionali.

Sikkerhetsnormer: Dette produktet tilfredsstiller følgende sikkerhetsnormer.

EN61000-3-2, EN61000-3-3

$

2 Advarsel: Hvis dette produktet benyttes til privat bruk, kan produktet forårsake

$

3 Immunitet EN55024

$

4 Elektrisk sikkerhet UL 1950 (UL/cUL), EN60950 (TUV), EN60825

$

5 Advarsel Laserprodukt av klasse 1.

$

6 Advarsal Stirr ikke på strålen.

$

7 ELEKTRISITET

$

8 FARE FOR LYNNEDSLAG

$

9 Forsiktig: STRØMLEDNINGEN BRUKES TIL Å FRAKOBLE UTSTYRET. FOR Å

$

10 UTSTYR FOR STIKKONTAKT. Stikkontakten skal monteres i nærheten av utstyret

$

11 Forsiktig: Lufteventilene må ikke blokkeres, og må ha fri tilgang til luft med

radioforstyrrelse. Hvis dette skjer, må brukeren ta de nødvendige forholdsregler.

Advarsel: FARE FOR ELEKTRISK SJOKK For å unngå ELEKTRISK sjokk, må
dekslet ikke tas av. Det finnes ingen deler som brukeren kan reparere på innsiden.
Denne enheten inneholder FARLIGE SPENNINGER, og må kun åpnes av en faglig
kvalifisert tekniker. For å unngå ELEKTRISK SJOKK må den elektriske strømmen til
produktet være avslått før LAN-kablene til- eller frakobles.

Fare: ARBEID IKKE på utstyr eller KABLER i TORDENVÆR.

DEAKTIVISERE UTSTYRET, må strømforsyningen kobles fra.

og skal være lett tilgjengelig."

romtemperatur for avkjøling.

31

$

12 Driftstemperatur: Dette produktet er konstruert for bruk i maksimum

$

13 Alle Land: Produktet må installeres i samsvar med de lokale og nasjonale elektriske

$

1 Emissão de interferência de

$

2 Aviso: Num ambiente doméstico este produto pode causar interferência na

$

3 Imunidade EN55024

$

4 Segurança Eléctrica UL 1950 (UL/cUL), EN60950 (TUV), EN60825

$

5 AVISO Produto laser de classe 1.

$

6Aviso Não olhe fixamente para o raio.

$

7 AVISOS SOBRE CARACTERÍSTICAS ELÉTRICAS

$

8 PERIGO DE CHOQUE CAUSADO POR RAIO

romtemperatur på 40 grader celsius.

koder.

Padrões: Este produto atende aos seguintes padrões.

radiofrequência FCC Part 15 (Class A), EN55022 (Class A),

radiorrecepção e, neste caso, pode ser necessário que o utente tome as medidas
adequadas.

Atenção: PERIGO DE CHOQUE ELÉTRICO Para evitar CHOQUE ELÉTRICO, não
retire a tampa. Não contém peças que possam ser consertadas pelo usuário. Este
aparelho contém VOLTAGENS PERIGOSAS e só deve ser aberto por um técnico
qualificado e treinado. Para evitar a possibilidade de CHOQUE ELÉTRICO,
desconecte o aparelho da fonte de energia elétrica antes de conectar e desconectar os
cabos da LAN.

Perigo: NÃO TRABALHE no equipamento ou nos CABOS durante períodos
suscetíveis a QUEDAS DE RAIO.

EN61000-3-2, EN61000-3-3

$

9 Cuidado: O CABO DE ALIMENTAÇÃO É UTILIZADO COMO UM DISPOSITIVO

$

10 EQUIPAMENTO DE LIGAÇÃO, a tomada eléctrica deve estar instalada perto do

$

11 Cuidado: As aberturas de ventilação não devem ser bloqueadas e devem ter acesso

$

12 Temperatura De Funcionamento: Este produto foi projetado para uma

$

13 Todos Os Países: Instale o produto de acordo com as normas nacionais e locais para

DE DESCONEXÃO. PARA DESELETRIFICAR O EQUIPAMENTO, desconecte o cabo
de ALIMENTAÇÃO.

equipamento e ser de fácil acesso."

livre ao ar ambiente para arrefecimento adequado do aparelho.

temperatura ambiente máxima de 40 graus centígrados.

instalações elétricas.

32

AT-FS713FC/xx and AT-FS717FC/xx Series Installation Guide

Estándares: Este producto cumple con los siguientes estándares.

$

1 Emisión RFI FCC Part 15 (Class A), EN55022 (Class A),

$

2 Advertencia: en un entorno doméstico, este producto puede causar

$

3 Inmunidad EN55024

$

4 Seguridad eléctrica UL 1950 (UL/cUL), EN60950 (TUV), EN60825

$

5 ¡Advertencia! Producto láser Clase 1.

$

6 ¡Advertencia! No mirat fijamente el haz.

$

7 AVISOS ELECTRICOS

$

8 PELIGRO DE RAYOS

$

9 Atencion: EL CABLE DE ALIMENTACION SE USA COMO UN

$

10 EQUIPO CONECTABLE, el tomacorriente se debe instalar cerca del equipo, en un

radiointerferencias, en cuyo caso, puede requerirse del usuario que tome las medidas
que sean convenientes al respecto.

Advertencia: PELIGRO DE ELECTROCHOQUE Para evitar un
ELECTROCHOQUE, no quite la tapa. No hay ningún componente en el interior al
cual puede prestar servicio el usuario. Esta unidad contiene VOLTAJES
PELIGROSOS y sólo deberá abrirla un técnico entrenado y calificado. Para evitar la
posibilidad de ELECTROCHOQUE desconecte la corriente eléctrica que llega al
producto antes de conectar o desconectar los cables LAN.

Peligro: NO REALICE NINGUN TIPO DE TRABAJO O CONEXION en los equipos o
en LOS CABLES durante TORMENTAS ELECTRICAS.

DISPOSITIVO DE DESCONEXION. PARA DESACTIVAR EL EQUIPO, desconecte
el cable de alimentación.

lugar con acceso fácil".

EN61000-3-2, EN61000-3-3

$

11 Atencion: Las aberturas para ventilación no deberán bloquearse y deberán tener

$

12 Temperatura Requerida Para La Operación: Este producto está diseñado para

$

13 Para Todos Los Países: Monte el producto de acuerdo con los Códigos Eléctricos

$

1 Radiostörning FCC Part 15 (Class A), EN55022 (Class A),

$

2 Varning: Denna produkt kan ge upphov till radiostörningar i hemmet, vilket kan

$

3 Immunitet EN55024

$

4 Elsäkerhet UL 1950 (UL/cUL), EN60950 (TUV), EN60825

$

5 Varning! Laserprodukt av klass 1.

$

6 Varning! Laserstrålning när enheten är öppen.

acceso libre al aire ambiental de la sala para su enfriamiento.

una temperatura ambiental máxima de 40 grados C.

locales y nacionales.

Standarder: Denna produkt uppfyller följande standarder.

EN61000-3-2, EN61000-3-3

tvinga användaren till att vidtaga erforderliga åtgärder.

33

$

7 Tillkännagivanden Beträffande Elektricitetsrisk:

$

8 FARA FÖR BLIXTNEDSLAG

$

9 Varning: NÄTKABELN ANVÄNDS SOM STRÖMBRYTARE FÖR ATT KOPPLA

$

10 UTRUSTNING MED PLUGG. Uttaget skall installeras i utrustningens närhet och

$

11 Varning: Luftventilerna får ej blockeras och måste ha fri tillgång till omgivande

$

12 Driftstemperatur: Denna produkt är konstruerad för rumstemperatur ej

$

13 Alla Länder: Installera produkten i enlighet med lokala och statliga bestämmelser

RISK FÖR ELEKTRISK STÖTFör att undvika ELEKTRISK stöt, ta ej av locket. Det
finns inga delar inuti som behöver underhållas. Denna apparat är under
HÖGSPÄNNING och får endast öppnas av en utbildad kvalificerad tekniker. För att
undvika ELEKTRISK STÖT, koppla ifrån produktens strömanslutning innan LAN­kablarna ansluts eller kopplas ur.

Fara: ARBETA EJ på utrustningen eller kablarna vid ÅSKVÄDER.

FRÅN STRÖMMEN, dra ur nätkabeln.

vara lättåtkomligt".

rumsluft för avsvalning.

överstigande 40 grader Celsius.

för elektrisk utrustning.

34

Appendix C

Technical Support Fax Order

Name _________________________________________________________________
Company______________________________________________________________
Address _______________________________________________________________
City______________________ State/Province_______________________________
Zip/Postal Code ________________ Country_______________________________
Phone______________________________ Fax________________________________

Incident Summary

Model number of Allied Telesyn product I am using________________________
Firmware release number of Allied Telesyn product _______________________
Other network software products I am using (e.g., network managers)

______________________________________________________________________
______________________________________________________________________

Brief summary of problem ______________________________________________

______________________________________________________________________

Conditions (List the steps that led up to the problem.) _____________________

______________________________________________________________________
______________________________________________________________________
______________________________________________________________________
______________________________________________________________________

______________________________________________________________________
Detailed description (Please use separate sheet)
Please also fax printouts of relevant files such as batch files and configuration

files. When completed, fax this sheet to the appropriate Allied Telesyn office.
Fax numbers can be found on page viii.

35