Adams Rite 2190-301-000, 2190-301-101-03, 2190-301-101-04, 2190-301-101-10B, 2190-301-101-32D Installation Instructions

1

STRIKE PREPARATION

OUTSWING LOCK STILE PREPARATION ONLY

FOR INSWING DOORS USE SMALL FORMAT LEVERS (4600)

AND REFER TO 4600 INSTRUCTION WITH 2190

BACKSET

1.250

BOTH WALLS

DEADLATCH

ALUMINUM FRAME

BACKSET

FOR CYLINDER

IN DOOR CL

.218

1.340

1.594

.196

C OF

CL OF

ONE WALL ONLY

L

C'SNK FOR #10

CYLINDER

.196

.928

CYLINDER

6.885

.938

ONE WALL ONLY

4.200

FLAT HD SCREW

2 PLS

C OF

6.375

4x, .177

1.125

6.375

4x, .177

.080

L

ONE WALL ONLY

4.200

STRIKE PLATE

(2 15/32")

2.310

2.238

1.212

1.125

1.212

THRU ONE

4x

.875

1.160

4.645

1.160

WALL ONLY

R.156

ONE WALL ONLY

5.375

3.306

.968

5.025

.968

3.390

2.520

.928

.938

2.520

2x

1.010

#10-32

.196

2101 STRIKE PLATE

ONE WALL ONLY

.500

.572

SHOWN

ONE WALL ONLY

ONE WALL ONLY

.968

.968

FOR

1.447

ELECTRIFIED OPTION

.177

INSTALLATION OF STRIKE

TOOLS NEEDED:

BACK OF LOCK STILE

- 5/64 ALLEN WRENCH

( EXTERIOR TRIM )

- APPLY STICK ON TEMPLATE OVER CYLINDER BACKSET CENTER LINE.

( INTERIOR TRIM )

- INSERT MOUNTING BACK PLATE BEHIND JAMB AND FASTEN WITH

- 3/32 ALLEN WRENCH

NOTE: EACH TEMPLATE IS LABELED FOR OUTSIDE OR INSIDE TRIM.

#10 FLAT HEAD SCREWS.

- 1/8 ALLEN WRENCH

- #9 DRILL BIT (.196 Ø)

- CENTER PUNCH ALL HOLES.

- INSERT TRIM BOX WITH 2101 STRIKE PLATE AND FASTEN WITH

- #16 DRILL BIT (.177 Ø)

- 7/8 DRILL BIT (.875 Ø)

- DRILL HOLES AT CENTER PUNCH LOCATIONS. REMOVE TEMPLATE.

#10 FLAT HEAD SCREWS TO BACK PLATE AS SHOWN.

- 1-1/8 DRILL BIT (1.125 Ø )

- INSTALL 2190 PER INSTALLATION INSTRUCTIONS.

2

BEVEL TABS ADJUSTMENT

FOR RADIUS FACEPLATE

3

TO CHANGE THE HANDING

- YOU WILL ALSO HAVE TO RE-ORIENT

LATCH

WITH WEATHERSEAL ONLY !

ON LATCH BOLT:

THE INTER-CONNECT CAM:

- ROTATE BEVEL TABS TO DESIRED HANDING.

BOLT

USING THE BEVEL ADJUSTMENT ALLOWS THE FLAT.

- WITH A SMALL FLAT HEAD

- DEPRESS THE LATCHBOLT UNTIL BOLT SCREW CAN BE

a) LOOSEN THE #6-32 FLAT HEAD SCREW

FACEPLATE TO WORK IN BEVEL STILES

RHR BEVEL LHR BEVEL

SCREWDRIVER, PRY OFF

1-1/2" BACKSET

SEEN THROUGH CASE HOLE. (1-1/2" BACKSET ONLY).

AT THE BOTTOM OF THE LOCK.

BEVEL TABS AS SHOWN.

- REMOVE BOLT SCREW AND ORIENT LATCH BOLT TO

SHOWN

b) ROTATE THE INTER-CONNECT CAM

THE OPPOSITE HAND.

TO THE SAME DIRECTION AS THE

- DEPRESS THE LATCH BOLT UNTIL THE COUNTERSINK

LATCH BOLT BEVEL.

RETIGHTEN THE #6-32 FLAT HEAD

HOLE ON THE LATCH BOLT CAN BE SEEN THROUGH THE

SCREW TO COMPLETE THE

CASE HOLE AS SHOWN IN FIG.1.

OPERATION.

- REINSERT BOLT SCREW AND TIGHTEN TO 22 - 27 IN-LB.

BEVELED

#6-32

FLAT HD

3a

SIDE SHOULD

#1-64 x 1/4" 3a

TO BLOCK HOLDBACK FEATURE:

SCREW

FACE THE SAME

FLAT HEAD SCREW

DIRECTION AS THE

a

- INSTALL #1-64 x 1/4" FLAT HEAD

INTER-CONNECT

SCREW INTO CASE AS SHOWN

CAM

AVAILABLE FACEPLATES

LATCH

3b

BEFORE INSTALLING IN DOOR.

b

BOLT

FOR APPLICATIONSTHAT REQUIRE

1-1/8 BACKSET

RETRACTION OF THE DEADBOLT

FLAT

AND DEADLATCH FROM BOTH

INTER-

SIDES OF THE DOOR. REMOVE THE

RADIUS

INTER-CONNECT CAM, AND INSTALL

CONNECT CAM

THE OPTIONAL DOUBLE

FIG.1

INTER-CONNECT CAM.

DOUBLE INTER-

FLAT or RADIUS

BACK VIEW

RADIUS WEATHER STRIP

#6 x1/2"

1-1/2 BACKSET

CONNECT CAM

3b

260 Santa Fe Street,

BOLT SCREW

(P/N 27-0268)

2190 INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

Adams Rite Manufacturing Co.

Pomona, CA 91767

W/ HEAVY DUTY ENTRANCE LEVER SET

Phone: [phone]

80-0180-410

Rev. D

ECN: 11883

Date: 02/03/2012

Page 1 of 3

Appvd: BC

Date: 02/09/12

www.adamsrite.com

Fax: [phone]