Adams Rite 3900-30-US3, 3900-30-US32D, 3900-36-32DMEC, 3900-36-US3, 3900-36-US32 Installation Instructions

FRAME PREPARATION

HEADER

3/4

HOLE

3/4

HOLE

STOP

BACKSET

STRIKE

7/16

C

L

RHR DOOR

STRIKE

7/16

LHR DOOR

13/16

INTERIOR
FACE OF
DOOR

7/16

LHR DOOR
INSIDE

BACKSET

C

FRAME

DOOR

13/16

INTERIOR

FACE OF

DOOR

7/16

REINFORCE
FOR STRIKE

STRIKE POST

*13/16

L

RHR DOOR
INSIDE

BACKSET

C

L

* MEASURED FROM THE INTERIOR DOOR
SURFACE. BE SURE TO ADJUST FOR
SILENCERS IF USED.

PRODUCT MUST BE INSTALLED

ACCORDING TO ALL APPLICABLE

BUILDING AND LIFE SAFETY CODES

Adams Rite Manufacturing Co.

10027 S. 51st Street, Suite 102

Phoenix, AZ 85044

Phone: [phone]

www.adamsrite.com

3900/8900 SURFACE LATCH CONCEALED ROD EXIT DEVICE

80-0180-390

JAMB

SINGLE DOOR

Rev.

R

BACKSET

DOOR

2 3/4"

2 3/4"

CN: 125-14

C

HOW TO FIND BACKSET

BACKSET

BACKSET

L

DOOR

PAIR DOOR

C

L

DOOR

BACKSET CENTERLINE IS TAKEN FROM
THE CENTERLINE OF THE SQUARE HOLE
ON TOP OF THE DOOR

C

L

INSTALLATION INSTRUCTIONS

Date:

04/10/14

Page of15

Appvd:

Date:

STEP

1

STEP

3a

WITH ENTRY TRIM

COVER PLATE

STEP

3b

NO ENTRY TRIM

PICTORIAL INSTALLATION GUIDE OF CAM

OVER SHAFT FOR LHR AND RHR DOORS.

INSIDE

FACE

COLLAR

5/8"

5/8"

DRILL BIT

APPLY DRILLING TEMPLATE
P/N 80-0180-392 FOR 3900/8900
TO THE DOOR. DRILL HOLES
AS DIRECTED. DRILL BIT WITH
COLLAR SHOWN FOR REF.

STEP

2

LAY THE ROD ASSEMBLY ON THE DOOR,
CENTERING THE BOTTOM OF THE ROD IN
THE BORED HOLE AS SHOWN. CUT THE
THREADED ROD IF NECESSARY TO AVOID
BOTTOMING OUT IN THE FEMALE ROD.
ADJUST THE TOP SQUARE BOLT 1.0" ABOVE
TOP OF DOOR. INSERT THE ENTIRE ROD
ASSEMBLY THROUGH THE OPENING ON TOP
OF DOOR. CENTER CAM INSIDE EXIT HOLE
AS PER DIAGRAM AND CLAMP SQUARE BOLT
AT TOP OF DOOR. OBSERVE LHR OR RHR AS
MAY BE THE CASE.

"A"

DRIVE
SHAFT

VIEW "A"

REPLACE FACTORY INSTALLED LONG DRVIE SHAFT
WITH SHORT DRIVE SHAFT FROM INSTALLATION KIT.
ATTACH THE COVER PLATE AND THE CENTER BLOCK
TO THE EXIT DEVICE USING (2) #10-32 X 1/2 PAN HEAD
SCREWS, ITEM #6, PUSH DOWN SCISSOR DEVICE FOR
SCREW ACCESS.

DOOR PREPARATION

THIS PRODUCT IS MADE FOR 1 3/4" DOOR WIDTH. FOR ANY

OTHER DOOR THICKNESS, YOU MUST CONSULT FACTORY

INSIDE

FACE

INSTALLED ACCORDING

TO ALL APPLICABLE BUILDING

AND LIFE SAFETY CODES

SCREW LIST
ITEM #6

CLAMP
HERE

PRODUCT MUST BE

THIS GROOVE

MUST ALWAYS

BE ON TOP

LHR

DOOR

DRIVE SHAFT

CAM

RHR

DOOR

LHR VIEW

Adams Rite Manufacturing Co.

10027 S. 51st Street, Suite 102

Phoenix, AZ 85044

Phone: [phone]

www.adamsrite.com

BORED
HOLE

BORED HOLE

FOR 6' 8" DOORS

REMOVE THREADED

ROD AND CUT 4"

RHR VIEW

3900/8900 SURFACE LATCH CONCEALED ROD EXIT DEVICE

80-0180-390

Rev.

R

CN: 125-14

Date:

04/10/14

THIS GROOVE

MUST ALWAYS

BE ON TOP

INSTALLATION INSTRUCTIONS

Page of25

Appvd:

DRIVE SHAFT

CAM

Date: