Acco CB345E, CB355E, CB405E, WB705E Illustrated Parts Lists and Service Instructions

ILLUSTRATED PARTS MANUAL:
FLOWLINE COMB & WIRE
BINDER RANGE

FLOWLINE COMB & WIRE

BINDER RANGE

Illustrated Parts Lists &

Service Instructions

CB345E, CB355E, CB405E, WB705E

Compiled by A Bumpsteed Issue No 20

Approved By D Mead Date 25/09/03

Acco Service Division; Halesowen Industrial Estate, Hereward Rise, Halesowen, West Midlands, B62 8AN

Tel: [phone] Fax: [phone]

Page 1 of 55

ILLUSTRATED PARTS MANUAL:
FLOWLINE COMB & WIRE
BINDER RANGE

TABLE OF CONTENTS

ILLUSTRATED PARTS MANUAL

FLOWLINE RANGE

Page

Contents 2

Preface 3 - 4

Illustrations and Parts with 5 - 20
Recommended Spares

CB345E 5 - 7
CB345E Diagram 8
CB355 E 9 - 11
CB355E Diagram 12
CB405E 13 - 16
CB405E Diagram 17
WB705E 18 - 20
WB705E Diagram 21

Service Instructions 22 - 46

Section 1 Document Support Lid 22
Section 2 Selector Switches 23
Section 3 Top Casing 24
Section 4 Infill Panel Assemblies 25
Section 5 Comb Opening Mechanism 26
Section 6 Comb Opening Spindle Assemble 27
Section 7 Lower Casing 28
Section 8 Operating Handle/Wire Closing Links 29
Section 9 Handle Locks 30
Section 10 Side frames/Stub Shaft Assembly 31
Section 11 Punches 32
Section 12 Punch Selector 33
Section 13 Wire Adjuster Assembly 34
Section 14 Gear Box Assembly 35 - 46

Wiring Diagrams 47 – 49

Wiring Diagram (230V) – WD431 Issue 1 47
Wiring Diagram (230V) – WD431 Issue 3 48
Wiring Diagram (115V) – WD436 Issue 1 49

Page 2 of 55

ILLUSTRATED PARTS MANUAL:
FLOWLINE COMB & WIRE
BINDER RANGE

Specifications 50 – 53

CB345E 50
CB355E 51
CB405E 52
WB705E 53

Amendment Record Sheet 54 - 55

Page 3 of 55

ILLUSTRATED PARTS MANUAL:
FLOWLINE COMB & WIRE
BINDER RANGE

PREFACE

This manual provides the instructions for the replacement of all the components that may become
worn or damaged. Details of replacement parts and ordering information are given in associated
illustrated parts list. For operating instructions see:-

OI-540 - Comb Binder
OI-541 - Wire Binder

Illustrated Parts Lists

For each machine, these give full details of the replacement part numbers with supporting diagrams to
show the location of the components.

Service Instructions

For each machine, these give the recommended servicing procedure with supporting pictorial
diagrams for added clarity.

WARNING

1. Check the RATING PLATE DETAILS on electric versions are compatible with the electrical

mains supply.

2. Disconnect the electrical mains supply before removing any covers.

3. After removing the cover on single phase machines, DISCHARGE the capacitor by shorting out

its connections. (BEWARE: PAPER DUST IS A POTENTIAL FIRE HAZARD).

4. All electric versions are DOUBLE INSULATED and do not require a sound Electrical Earth

Connection.

5. Following any Service activity an Earth Bond/Continuity Test or preferably (if available) a

PAT/Flash Test should be performed on the Binder to verify 4 above, before releasing Binder
back to the Customer.

Page 4 of 55

ILLUSTRATED PARTS MANUAL:
FLOWLINE COMB & WIRE
BINDER RANGE

MODEL CB345E

Part No Description Qty Comments
A55216 Quadrant Gear RH 1
A55217 Quadrant Gear LH 1
BSH78 Oilite Bearing 6.5 Long 1
BSH79 Oilite Bearing AL1824 12mm long 1
D47010 13T Gear 2
D55050 Comb binder die plate 1
D55051 Comb binder stripper plate 2
D55053 Spacer block 1
D55062A Side Frame LH Electric 1 Made from D55062
D55072 Gear Shaft - Long 1
D55073 Gearbox Top Casing 1
D55074 Gearbox bottom casing 1
D55076 Comb Opening Drive Plate 1
D55077 Comb Opening Finger Plate 1
D55078 Clamp Plate 1
D55079 Comb Opening Base Plate 1
D55087 Die Support Block 1
D55091 Comb Opening Clamp Spring 2
D55100 Spacer Washer 6
D55108 Margin Adjuster Screw 1
D55109 Margin Adjuster Thumb Wheel 1
D55110E Top Cover 1
D55111C Bottom Casing 1
D55112A Document Measurer 1 Supplied as part of A55173F – See Issue 19
D55115A Side Frame RH 1 Made from D55115
D55123 Rubber Foot 2
D55125 Document Support Lid 1
D55127 Comb Opening Knob 1
D55130 Clippings Tray 1
D55131 Comb Knob Spring 2
D55133F Infill Panel 1 Supplied as part of A55173F – See Issue 19
D55135 Punch Button 1
D55136 Punch Button Spring 1
D55144 Comb Opening door shaft single knob 1
D55146 Comb Opening Bung 1
D55147 Punch Handle Bung 2
D55148 PCB Activation Cam 1
D55156 Punch Retainer 1
D55159 Document Measurer Spring 1 Supplied as part of A55173F – See Issue 19
D55162 Motor Pinion 1
D55163 Gear Shaft Short 1
D55189 Compound Gear 34/13T 1
D55190 Compound Gear 41/10T (Plastic) 1 To S/no A678190 Replaced by D55241/PLN29 – See Issue 5
D55191 Spur Gear 29T 1
D55192 Spur Gear 13T 2
D55193 Motor Support Bracket 1
D55194 Hex Spindle for gear box 1
D55195 Hexagon Spindle 1
D55198 Buffer 2
D55199 Knob retaining clip 1
D55200 Fixed Spindle 2
D55202 Rubber Foot - L Shaped 2
D55203 Rubber Foot - Front 2

Page 5 of 55

ILLUSTRATED PARTS MANUAL:
FLOWLINE COMB & WIRE
BINDER RANGE

D55213 Punch Switch Insulation collar 1
D55214 Tie Bar 1
D55215 Compound Gear 26/10T 1
D55218 Tie Rod Bush 2
D55219 Motor insulator 1
D55220 Gear Box end plate 1
D55226 Wire - cap to PCB 1
D55227 Laser Punch Plate 1
D55236 Gear Box Shaft Retainer 1 See Issue 3
D55240 Compound Gear 41/10T (Sintered) 1 See Issue 12
D55241 Compound Gear 41/10T (Metal) 1 From S/No A678191 to A710068 See Issues 5 and 12
D55242 Thermal Fuse Assembly 1 From S/No A670764 to A694089 See Issues 4 and 11
PEG93 6 x 50mm heavy duty spirol pin 3
PLN2L 3BA plain washer 4
PLN29 M5 plain washer 1 From S/No A678191 to A710068 See Issues 5 and 12
PLN37 M9 Shim Washer 1
SCM157 M6 x 20 Taptite 4
SCM158 M5 x 16 Taptite 2
SCM159 M6 x 50 Taptite 3
SCM160 M4 x 12 Taptite 6
SCM162 M4 x 10 Screw 3
SCR718 M4 x 10 Plasform 1 Pozi Pan Screw 2 See Issue 6
SCR720 M3.5 x 10 plastech 9
SCR721 M2.5 x 8 Screw 2
SCR722 M5 x 16 Plasfix Screw 8
SCR724 M3 x 8 Screw 6
SCR725 M5 x 20 Screw 7
SHK2 3BA Shakeproof Washer 2
SL17-144 Cable Tie 6
SL17-300 Binder Motor PCB 1 To S/No A721640 – See Issue 14
SL17-301 Binder LED PCB 1 To S/No A721640 – See Issue 14
SL17-313 Binder LED PCB 1 From S/No A721641 – See Issue 14
SL17-314 Binder Motor PCB 1 From S/No A721641 – See Issue 14
SL18-361 Cable Clamp 1 See Issue 6
SL18-368 PCB Mounting Block 3
SL18-380 Insulating Tape (RS494-679) in mm 75 See Issue 7 was SL18-377 x 100mm See Issue 8
SL18-383 Printed Button 1 From S/No A721641 – See Issue 14
SL20-317 Motor 140W 1
SL4-124 Cord Set UK – 2 core 1
SL4-125 Cord Set EURO – 2 core 1
SL6-76 9MFD Capacitor 1
TRU100 E Clip 2
TRU99 Carbon Steel E Clip 5

A55064 Edge Margin Guide Assembly (Spares) 1 Comprises D55108 and D55109
A55173F Infill Panel Assembly CB345E 1 Comprises D55133F, D55112A and D55159
A55174F Comb Opening Mechanism (Spares)

Not supplied as an assembly

A55179 Die Block Assembly (Spares) 1 Comprises D55050, D55051, D55053, D55087, D55100,

A55222 Motor/Gearbox Assembly (Spares) 1 Comprises BSH78, BSH79, D55072, D55073, D55074,

1 Comprises D55076, D55077, D55078, D55079, D55091,

D55135, D55136, D55213, SL17-301 and A55173F

PEG93 and SCM159

D55162, D55163, D55189, D55191, D55193, D55215,
D55219, D55220, D55226, D55236, D55240, SCM160 (2off),
SCM162, SCR722 (4off), SCR725, SHK2, SL6-72, SL17­144, SL20-317 and TRU99 – See Issues 11 and 12

Page 6 of 55

ILLUSTRATED PARTS MANUAL:
FLOWLINE COMB & WIRE
BINDER RANGE

A55238 Side Frame Assembly LH (Spares) 1 Comprises D55062A and D55200 (1off)
A55239 Side Frame Assembly RH (Spares) 1 Comprises D55115A and D55200 (1off)

Page 7 of 55

CB345E Diagram

ILLUSTRATED PARTS MANUAL:
FLOWLINE COMB & WIRE
BINDER RANGE

Page 8 of 55

ILLUSTRATED PARTS MANUAL:
FLOWLINE COMB & WIRE
BINDER RANGE

MODEL CB355E

Part No Description Qty Comments
A55216 Quadrant Gear RH 1
A55217 Quadrant Gear LH 1
BSH78 Oilite Bearing 6.5 Long 1
BSH79 Oilite Bearing AL1824 12mm long 1
D47010 13T Gear 2
D55050 Comb binder die plate 1
D55051 Comb binder stripper plate 2
D55053 Spacer block 1
D55062A Side Frame LH Electric 1 Made from D55062
D55065 Punch - Individual 21
D55072 Gear Shaft - Long 1
D55073 Gearbox Top Casing 1
D55074 Gearbox bottom casing 1
D55076 Comb Opening Drive Plate 1
D55077 Comb Opening Finger Plate 1
D55078 Clamp Plate 1
D55079 Comb Opening Base Plate 1
D55087 Die Support Block 1
D55091 Comb Opening Clamp Spring 2
D55100 Spacer Washer 6
D55108 Margin Adjuster Screw 1
D55109 Margin Adjuster Thumb Wheel 1
D55110E Top Cover 1
D55111C Bottom Casing 1
D55112A Document Measurer 1 Supplied as part of A55173A – See Issue 19
D55115A Side Frame RH 1 Made from D55115
D55123 Rubber Foot 2
D55125 Document Support Lid 1
D55127 Comb Opening Knob 1
D55128 Wire Closing Cover 1
D55130 Clippings Tray 1
D55131 Comb Knob Spring 2
D55133B Infill Panel 1 Supplied as part of A55173A – See Issue 19
D55135 Punch Button 1
D55136 Punch Button Spring 1
D55144 Comb Opening door shaft single knob 1
D55146 Comb Opening Bung 1
D55147 Punch Handle Bung 2
D55148 PCB Activation Cam 1
D55155 Pull Plate 1
D55156 Punch Retainer 1
D55159 Document Measurer Spring 1 Supplied as part of A55173A – See Issue 19
D55162 Motor Pinion 1
D55163 Gear Shaft Short 1
D55189 Compound Gear 34/13T 1
D55190 Compound Gear 41/10T (Plastic) 1 To S/No A678190 Replaced by D55241/PLN29 – See Issue 5
D55191 Spur Gear 1
D55192 Spur Gear 13T 2
D55193 Motor Support Bracket 1
D55194 Hex Spindle for gear box 1
D55195 Hexagon Spindle 1
D55197 Storage Tray 1
D55198 Buffer 2
D55199 Knob retaining clip 1

Page 9 of 55

ILLUSTRATED PARTS MANUAL:
FLOWLINE COMB & WIRE
BINDER RANGE

D55200 Fixed Spindle 2
D55202 Rubber Foot - L Shaped 2
D55203 Rubber Foot - Front 2
D55213 Punch Switch Insulation collar 1
D55214 Tie Bar 1
D55215 Compound Gear 26/10T 1
D55218 Tie Rod Bush 2
D55219 Motor insulator 1
D55220 Gear Box end plate 1
D55226 Wire - cap to PCB 1
D55229 Push Plate 1
D55236 Gear Box Shaft Retainer 1 See Issue 3
D55240 Compound Gear 41/10T (Sintered) 1 See Issue 12
D55241 Compound Gear 41/10T (Metal) 1 From S/No A678191 to A710068 See Issues 5 and 12
D55242 Thermal Fuse Assembly 1 From S/No A670764 to A694089 See Issues 4 and 11
PEG93 6 x 50mm heavy duty spirol pin 3
PEG95 1/8 x 3/8" medium duty spirol 21
PLN2L 3BA plain washer 4
PLN29 M5 plain washer 1 From S/No A678191 to A710068 See Issues 5 and 12
PLN37 M9 Shim Washer 1
RTS73 Rivet 3
SCM157 M6 x 20 Taptite 4
SCM158 M5 x 16 Taptite 2
SCM159 M6 x 50 Taptite 3
SCM160 M4 x 12 Taptite 6
SCM162 M4 x 10 Screw 3
SCR718 M4 x 10 Plasform 1 Pozi Pan Screw 2 See Issue 6
SCR720 M3.5 x 10 plastech 9
SCR71 M2.5 x 8 Screw 2
SCR722 M5 x 16 Plasfix Screw 8
SCR724 M3 x 8 Screw 6
SCR725 M5 x 20 Screw 7
SHK2 3BA Shakeproof Washer 2
SL17-144 Cable Tie 6
SL17-300 Binder motor PCB 1 To S/No A717392 – See Issue 14
SL17-301 Binder LED PCB 1 To S/No A717392 – See Issue 14
SL17-313 Binder LED PCB 1 From S/No A717393 – See Issue 14
SL17-314 Binder Motor PCB 1 From S/No A717393 – See Issue 14
SL18-361 Cable Clamp 1 See Issue 6
SL18-368 PCB Mounting Blocks 3
SL18-380 Insulating Tape (RS494-679) in mm 75 See Issue 7. Was SL18-377 x 100mm See issue 8
SL18-383 Printed Button 1 From S/No A717393 – See Issue 14
SL20-317 Motor 140W 1
SL4-124 Cord Set UK – 2 core 1
SL4-125 Cord Set EURO – 2 core 1
SL4-129 Cord Set AUST – 2 core 1 See Issue 13
SL6-76 9MFD Capacitor 1

A55064 Edge Margin Guide Assembly (Spares) 1 Comprises D55108 and D55109
A55173A Infill Panel Assembly CB355E 1 Comprises D55133B, D55112A and D55159
A55174A Comb Opening Mechanism (Spares)

Not supplied as an assembly

A55059B Die Block Assembly (Spares) 1 Comprises D55050, D55051, D55053, D55065, D55087,

1 Comprises D55076, D55077, D55078, D55079, D55091,

D55135, D55136, D55213, SL17-301 and A55173A

Page 10 of 55

ILLUSTRATED PARTS MANUAL:
FLOWLINE COMB & WIRE
BINDER RANGE

D55100, D55156, PEG93, PEG95 and SCM159
A55180D Push Plate Assembly (Spares) 1 Comprises D55229, D55155 and RTS73
A55222 Motor/Gearbox Assembly (Spares) 1 Comprises BSH78, BSH79, D55072, D55073, D55074,

D55162, D55163, D55189, D55191, D55193, D55215,

D55219, D55220, D55226, D55236, D55240, SCM160 (2off),

SCM162, SCR722 (4off), SCR725, SL6-72, SL17-144, SL20-

317 and TRU99 See Issue 12
A55238 Side Frame Assembly LH (Spares) 1 Comprises D55062A and D55200 (1off)
A55239 Side Frame Assembly RH (Spares) 1 Comprises D55115A and D55200 (1off)

Page 11 of 55

ILLUSTRATED PARTS MANUAL:
FLOWLINE COMB & WIRE
BINDER RANGE

MODEL CB355E DIAGRAM

Page 12 of 55

ILLUSTRATED PARTS MANUAL:
FLOWLINE COMB & WIRE
BINDER RANGE

MODEL CB405E

Part No Description Qty Comments
A55207 Mobile Jaw Assembly 1
A55216 Quadrant Gear RH 1
A55217 Quadrant Gear LH 1
BSH78 Oilite Bearing 1
BSH79 Oilite Bearing AL1824 1
D000431 Footswitch Decal 1
D47010 13T Gear 2
D55050 Comb Binder Die Plate 1
D55051 Comb Binder Stripper Plate 2
D55053 Spacer Block 1
D55055 Margin Guide 1
D55056 Spacer Washer 6
D55062A Side Frame LH 1 Made from D55062A
D55065 Punch - Individual 21
D55066 Punch Selector 3
D55072 Gear Shaft Long 1
D55073 Gearbox Top Casing 1
D55074 Gearbox bottom casing 1
D55076 Comb Opening Drive Plate 1
D55077 Comb Opening Finger Plate 1
D55078 Clamp Plate 1
D55079 Comb Opening Base Plate 1
D55081 Punch Handle Side Piece LH 1
D55083B Wire Closing Jaw Fixed 1
D55084 Punch Handle Side Piece RH 1
D55085 Handle Grip Long 1
D55087 Die Support Block 1
D55088 Comb Opening Drive Shaft 1
D55091 Comb Opening Clamp Spring 2
D55101 Handle Lock Cam LH 1
D55102 Handle Lock Cam RH 1
D55108 Margin Adjuster Screw 1
D55109 Margin Adjuster Thumb Wheel 1
D55110A Top Cover 1
D55111A Bottom Casing 1
D55112A Document Measurer 1 Supplied as part of A55173B – See Issue 19
D55112C Document Measurer 1 US Variant only – See Issue 16. Supplied as part of A55173I.

– See Issue 19
D55113 Back Stop Slider 1
D55115A Side Frame RH 1 Made from D55115
D55117 Comb Open Stop LH 1 Supplied as part of A55173A and A55173I – See Issue 19
D55118 Comb Open Stop RH 1 Supplied as part of A55173A and A55173I – See Issue 19
D55119 Comb Open Stop Plunger 1 Supplied as part of A55173A and A55173I – See Issue 19
D55123 Rubber Foot Back/Top 2
D55124 Wire Closing Spring 2
D55125 Document Support/lid 1
D55127 Comb Opening Knob 2
D55128 Wire Closing Cover 1 To S/No A713322 – See Issue 15
D55128P Wire Closing Cover Printed 1 From S/No A713323 – See Issue 15
D55130 Clippings Tray 1
D55131 Comb Opening Knob Spring 2
D55132 Comb Opening Stop Extension 1
D55133A Infill Panel 1 Supplied as part of A55173A – See Issue 19

Page 13 of 55

ILLUSTRATED PARTS MANUAL:
FLOWLINE COMB & WIRE
BINDER RANGE

D55133G Infill Panel 1 US Variant only – See Issue 16. Supplied as part of A55173I.

– See Issue 19
D55135 Punch Button 1
D55136 Punch Button Spring 1
D55138 Punch Selector Spring 3
D55139 Punch Selector Switch R 1
D55140 Punch Selector Switch M 1
D55141 Punch Selector Switch L 1
D55148 PCB Activation Cam 1
D55149 Comb Opening Stop Spring 1 Supplied as part of A55173A and A55173I – See Issue 19
D55155 Pull Plate 1
D55156 Punch Retainer 1
D55159 Document Measurer Spring 1 Supplied as part of A55173A – See Issue 19
D55162 Motor Pinion 1
D55163 Gear Shaft Short 1
D55166 Comb Open Stop Switch Mech Cover 1 To S/No A765520 – See Issue 18
D55189 Compound gear 34/13T 1
D55190 Compound gear 41/10T (Plastic) 1 To S/No A678190 Replaced by D55241/PLN29 – See Issue 5
D55191 Spur Gear 29T 1
D55192 Spur Gear 13T 2
D55193 Motor Support Bracket 1
D55194 Hex Spindle for gearbox 1
D55195 Hexagon Spindle 1
D55198 Buffer 2
D55199 Knob retaining clip 2
D55200 Fixed spindle 2
D55202 Rubber Foot - L Shape 2
D55203 Rubber foot – front 2
D55211 Wire Link no adjuster LH 1
D55212 Wire Link no adjuster RH 1
D55213 Punch Switch Insulation collar 1
D55215 Compound Gear 1
D55219 Motor insulator 1
D55220 Gearbox 1
D55225 Foot Pedal Socket and Lead 1
D55226 Wires - Cap to PCB 1
D55228 Push Plate 1
D55230 Handle Lock Spindle 1
D55236 Gear Box Shaft Retainer 1 See Issue 3
D55240 Compound Gear 41/10T (Sintered) 1 See Issue 12
D55241 Compound Gear 41/10T (Metal) 1 From S/No A678191 to A710068 See Issues 5 and 12
D55242 Thermal Fuse Assembly 1 From S/No A670764 to A694089 See Issues 4 and 11
D55246 Wires – Cap to PCB – 120v 1 US Variant only – See Issue 16
D55247 Ribbon Cable Bridge Piece 1 From S/No A721022 – See Issue 14
D55248 120v – Cap Insulator 1 US Variant only – See Issue 16
D55249 PCB Switch Insulator 1 US Variant only – See Issue 16
D55250 Cap Insulator End Piece 1 US Variant only – See Issue 16
D55252 Motor Insulator - Lower 1 US Variant only – See Issue 16
D55270 Fan Unit Bracket 1 US Variant only – See Issue 16
D55271 Retaining Plate 1 US Variant only – See Issue 16
D55272 Rivet Washer Plate 1 US Variant only – See Issue 16
PEG93 6 x 50mm heavy duty spirol pin 3
PEG95 1/8 x 3/8" medium duty spirol 21
PEG97 6mm dia x 16mm long dowel pin 2
PLN2L 3BA plain washer 4
PLN29 M5 plain washer 1 From S/No A678191 to A710068 See Issues 5 and 12

Page 14 of 55

ILLUSTRATED PARTS MANUAL:
FLOWLINE COMB & WIRE
BINDER RANGE

PLN36 M8 plain washer 2
PLN37 M9 shim washer 1
RTS19 Tap/D/46/BS Pop Rivet (For C/Fan) 5 US Variant only – See Issue 16
RTS73 3.2 x 8mm fashtech euro rivet 3
SCM157 M6 x 20 pan torx taptite screw 8
SCM158 M5 x 16 pan torx taptite screw 2
SCM159 M6 x 50 pan torx taptite screw 3
SCM160 M4 x 12 pan torx taptite screw 7 Was 6 off – See Issue 14
SCM162 M4 x 10 pan head torx m/c screw 3
SCM163 M3 x 10mm pan torx taptite 2
SCR718 M4 x 10 Plasform 1 Pozi Pan screw 2 See Issue 6 – 230v only
SCR720 M3.5 x 10 pan torx plastech screw 9
SCR721 M2.5 x 8 Rec Pan plastech screw 2
SCR722 M5 x 16 pan plasfix screw 8
SCR724 M3 x 8 plastech pan head torx 6
SCR725 M5 x 20 plastfix pan head torx 7
SHK2 3BA Shakeproof Washer 2
SL17-144 Cable Tie 6
SL17-300 Binder Motor PCB 1 To S/No A721021 – See Issue 14
SL17-301 Binder LED PCB 1 To S/No A721021 – See Issue 14
SL17-312 Binder Main PCB – 120v 1 US Variant only – See Issue 16
SL17-313 Binder LED PCB 1 From S/No A721022 – See Issue 14
SL17-314 Binder Motor PCB 1 From S/No A721022 – See Issue 14
SL18-361 Cable Clamp 1 See Issue 6 – 230v only
SL18-366 Spring Plunger 1
SL18-368 PCB Mounting block PCB 3
SL18-380 Insulating Tape (RS494-679) in mm 75 See Issue 7. Was SL18-377 x 100mm See issue 8
SL18-381 Strain Relief Bushing 1 US Variant only – See Issue 16
SL18-383 Printed Button 1 From S/No A721022 – See Issue 14
SL20-317 Motor 1
SL20-322 Motor – 120v 1 US Variant only – See Issue 16
SL25-11 Cooling Fan 1 US Variant only – See Issue 16
SL4-124 Cord Set UK – 2 core 1
SL4-125 Cord Set EURO – 2 core 1
SL4-128 Cord Set US – 2 core 1 US Variant only – See Issue 16
SL4-129 Cord Set AUST – 2 core 1 See Issue 13
SL6-59 25MFD Capacitor 1 US Variant only – See Issue 16
SL6-76 9MFD Capacitor 1
SL8-173 Foot Switch 1
TRU100 E Clip 2
TRU99 Carbon Steel E Clip 3

A55173B Infill Panel Assembly CB405E 1 Comprises D55112A, D55117, D55118, D55119, D55133A,

D55149 and D55159
A55173I Infill Panel Assembly CB405E US 1 Comprises D55112C, D55117, D55118, D55119, D55133G,

D55149 and D55159
A55174B Comb Opening Mechanism (Spares)

Not supplied as an assembly

A55059A Die Block Assembly (Spares) 1 Comprises D55050, D55051, D55053, D55056, D55065,

A55064 Edge Margin Guide Assembly (Spares) 1 Comprises D55108 and D55109
A55180B Push Plate Assembly (Spares) 1 Comprises D55228, D55155 and RTS73
A55222 Motor/Gearbox Assembly (Spares) 1 Comprises BSH78, BSH79, D55072, D55073, D55074,

1 Comprises D55076, D55077, D55078, D55079, D55091,

D55132, D55135, D55136, D55213, SL17-301 and A55173B

D55087, D55156, PEG93, PEG95 and SCM159

D55162, D55163, D55189, D55191, D55193, D55215,

D55219, D55220, D55226, D55236, D55240, SCM160

(2off), SCM162, SCR722 (4off), SCR725, SHK2, SL6-72,

Page 15 of 55

ILLUSTRATED PARTS MANUAL:
FLOWLINE COMB & WIRE
BINDER RANGE

SL17-144, SL20-317 and TRU99 See Issue 12
A55223 Punch Handle Side Piece RH Assembly

(Spares)

A55224 Punch Handle Side Piece LH Assembly

(Spares)

A55251 Motor/Gearbox Assembly US (Spares) 1 Comprises BSH78, BSH79, D55072, D55073, D55074,

1 D55084 and PEG97

1 D55081 and PEG97

D55162, D55163, D55189, D55191, D55193, D55215,

D55219, D55220, D55226, D55236, D55240, D55246,

D55248, D55249, D55250, D55252, SCM160 (2off),

SCM162, SCR722 (4off), SCR725, SHK2, SL6-59, SL17-

144, SL17-312, SL20-322 and TRU99 - See Issue 16

Page 16 of 55

CB405E DIAGRAM

ILLUSTRATED PARTS MANUAL:
FLOWLINE COMB & WIRE
BINDER RANGE

Page 17 of 55