4IPNET EAP737 User Manual

EAP737
Enterprise Access Point
Quick Installation Guide
To download up-to-date version, please visit www.4ipnet.com.
EAP737 Enterprise Access Point ENGLISH
Copyright Notice
This document is protected by USA copyright laws and other laws. Besides, the
document is the property of 4IPNET, INC. You may not copy, reproduce, distribute,
publish, display, perform, or modify any part of this publication in any form or by any
means without prior written permission from 4IPNET, INC. You may not alter or remove any
copyright or other notice from copies of the content. All other brand and product names
are claimed or registered marks of their respective companies or organizations.
All rights reserved.
Copyright © 4IPNET, INC. All rights reserved.
Quick Installation Guide
EAP737 Enterprise Access Point ENGLISH
FCC CAUTION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.
This device is restricted to indoor use when operated in the 5.15 to 5.25 GHz frequency range. FCC requires this product to be used indoors for the frequency range 5.15 to 5.25 GHz to reduce the
potential for harmful interference to co-channel Mobile Satellite systems.
IMPORTANT NOTE: FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Copyright © 4IPNET, INC. All rights reserved.
Quick Installation Guide
根據 NCC 低功率電波輻射性電機管理辦法 規定:
第十二條
經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、加大功率或
變更原設計之特性及功能。
第十四條
低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善
至無干擾時方得繼續使用。前項合法通信,指依電信法規定作業之無線電通信。低功率射頻電機須忍受
合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。
5.25 ~ 5.35 秭赫頻帶內操作之無線資訊傳輸設備,限於室內使用。
EAP737 Enterprise Access Point ENGLISH
CE CAUTION
Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive) for European Community, Switzerland, Norway, Iceland, and Liechtenstein Model: EAP737
For 2.4 GHz radios, the device has been tested and passed the requirements of the following standards, and hence fulfills the EMC and safety requirements of R&TTE Directive within the CE marking requirement.
• Radio: EN 300.328
:
EMC: EN 301.489-1, EN 301.489-17,
• EMC: EN 55022 Class B, EN 55024:+ A1 + A2 including the followings:
EN 61000-3-2, EN 61000-3-3. EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61000-4-11
• Safety: EN 60950-1 + A11,
Caution:
This declaration is only valid for configurations (combinations of software, firmware, and hardware)
provided and supported by 4ipnet Inc. The use of software or firmware not provided and supported by 4ipnet Inc. may result in the equipment no longer being compliant with the regulatory requirements.
European standards dictate maximum radiated transmit power of 100mW EIRP and frequency range
2.400-2.4835 GHz. This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. Contact your local regulatory authority for compliance.
Taiwan NCC Statement
減少電磁波影響,請妥適使用
Copyright © 4IPNET, INC. All rights reserved.
Quick Installation Guide
Preface
Package Contents
4ipnet EAP737 is a high-end, dual radio 802.11 b/g/n + ac (Wave 2) MIMO Access Point (AP) with the best performance for business and industrial applications and is compliant with the latest industrial wireless security standards that are required in the tightly secured enterprise network environments. EAP737 makes the wireless communication fast, secure and easy. It supports business grade security such as 802.1X, and Wi-Fi Protected Access (WPA and WPA2). The EAP737 supports multiple point-to-point wireless links to form wider wireless network coverage. EAP737 also features multiple ESSIDs with VLAN tags and multiple Virtual APs; great for enterprise applications, such as separating traffic from different departments using different ESSIDs. The PoE Uplink port is able to receive power from Power over Ethernet (PoE) sourcing devices. This Quick Installation Guide provides instructions and reference materials to get you started with 4ipnet EAP737.
1. 4ipnet EAP737 x 1
2. Quick Installation Guide (QIG) x 1
3. Mounting Kit x 1
4. Power Adaptor (12V) x 1 (Optional)
It is recommended to keep the original
packing material for possible future shipment when repair or maintenance is required. Any returned product should be packed in its original packaging to prevent damage during delivery.
EAP737 Enterprise Access Point ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
Quick Installation Guide
System Overview
EAP737 Enterprise Access Point ENGLISH
EAP737 Front View
Copyright © 4IPNET, INC. All rights reserved.
EAP737 Side View
Quick Installation Guide
1
LED Indicators
An LED indicator is available to show the status.
2
K-Slot
Use Kensington lock for anti-theft purpose.
3
Restart / Reset
Press once to restart the system; to reset the system to factory default settings, hold for more than 5 seconds.
4
12V 1.5 A
Attach power adaptor here.
5
Uplink (PoE) Port
Offers uplink connection. This port can be used to connect to a controller, gateway, or directly to the Internet. 802.3af PoE is also supported.
6
LAN Port
The ports for connections with LAN side devices.
7
Console Port
To access EAP737 via the console interface.
8
USB Port
USB interface reserved for future use.
EAP737 Enterprise Access Point ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
Quick Installation Guide
Hardware Installation
EAP737 Enterprise Access Point ENGLISH
Please follow the steps mentioned below to install the hardware of EAP737:
1. Place the EAP737 at the best location.
a) The best location for EAP737 is usually at the center of your intended wireless network.
- Secure mounting bracket on the wall with screws.
- Attach the Access Point to the dedicated slots on the mounting bracket.
- After attach the Access Point to the mounting bracket, slide down the Access Point to fasten it.
Copyright © 4IPNET, INC. All rights reserved.
Quick Installation Guide
Using a different power adapter may damage this system. To verify the wired connection between EAP737 and you switch / router / hub, please also
check the LED status indicator of the respective network devices.
EAP737 Enterprise Access Point ENGLISH
2. Connect the EAP737 to your network device.
Connect one end of the Ethernet cable to the Uplink port of EAP737 and the other end of the cable to a switch, a router, or a hub. EAP737 is then connected to your existing wired LAN network.
3. Power on the EAP737.
There are two ways to supply power over to EAP737.
- EAP737 Uplink port is capable of receiving DC currents. Connect an IEEE 802.3af-compliant PSE device (e.g. a PoE-switch) to the Uplink port of EAP737 with the Ethernet cable.
- Connect a 12V/1.5A adaptor (optional) to the DC power jack. If needed.
Now, the Hardware Installation is complete.
Copyright © 4IPNET, INC. All rights reserved.
Quick Installation Guide
Getting Started
EAP737 Enterprise Access Point ENGLISH
4ipnet EAP737 supports web-based configuration. When hardware installation is complete, EAP737 can be configured through a PC by using a web browser such as Mozilla Firefox 2.0 or Internet Explorer version 6.0 and above.
The default values of LAN IP address and subnet mask of EAP737 are:
IP Address: 192.168.1.1 Subnet Mask: 255.255.255.0
Steps:
1. To access the Web Management Interface, connect the administrator PC to the Uplink port of EAP737 via an Ethernet cable. Then, set a static IP address on the same subnet mask as EAP737 in TCP/IP of your PC, such as the following example:
IP Address: 192.168.1.100 Subnet Mask: 255.255.255.0
2. Launch the web browser on your PC by entering the IP address of EAP737 (http://192.168.1.1) in the address field, and then press Enter.
Example of entering EAP737's default IP Address via a web browser
3. The following Admin Login Page will appear. Enter adminfor both the Username and Password fields, and then click Login.
Copyright © 4IPNET, INC. All rights reserved.
Administrator Login Page
Quick Installation Guide
EAP737 Enterprise Access Point ENGLISH
4. After a successful login to EAP737, a System Overview page of the Web Management Interface will appear, as depicted below.
The Web Management Interface - System Overview Page
5. To logout, simply click on the Logout button at the upper right hand corner of the interface to return to the Administrator Login Page. Click OK to logout.
Copyright © 4IPNET, INC. All rights reserved.
Quick Installation Guide
Common Settings
Step 1. Change Administrator’s Password
EAP737 Enterprise Access Point ENGLISH
Change Password Page
Click on the Utilities icon on the main menu, and select the Change Password tab. Enter a new password with a length of up to 32 characters, and retype it in the Re-enter New
Password field.
Click SAVE to save the changes.
Copyright © 4IPNET, INC. All rights reserved.
Quick Installation Guide
Step 2. Configure General AP (Access Point) Settings
EAP737 Enterprise Access Point ENGLISH
Wireless General Settings Page
Click on the Wireless icon on the main menu, and then select the General tab. Determine the Band, Protocol and Channel settings:
Select your preferred Band, Protocol and Channel for you wireless connection. For example, select
2.4GHz for the band, 802.11g+802.11n for the protocol and 6 for the channel.
Copyright © 4IPNET, INC. All rights reserved.
Quick Installation Guide
EAP737 Enterprise Access Point ENGLISH
Step 3. Configure VAP (Virtual Access Point) Profile Settings
VAP Configuration Page (VAP-1 shown)
Configure VAP profile settings
(a) Select the VAP Configuration tab to configure the settings of the desired VAP. (b) Enable a specific VAP from the drop-down menu of Profile Name and configure related settings below.
Check VAP status
After finishing VAP configuration, the status of enabled Virtual APs shall be reflected on the VAP Overview page.
Copyright © 4IPNET, INC. All rights reserved.
Quick Installation Guide
EAP737 Enterprise Access Point ENGLISH
Virtual AP Overview Page
Copyright © 4IPNET, INC. All rights reserved.
Quick Installation Guide
Note:
On each and every configuration page, you may click SAVE to save the changes of your configured settings, but you must reboot the system for the changes to take effect. After clicking SAVE, the following message will appear: Some modifications have been saved and will take effect after APPLY.
EAP737 Enterprise Access Point ENGLISH
Step 4. Configure WDS (Wireless Distribution System) Settings (Optional)
To extend the wireless coverage, EAP737 supports WDS links on each RF card for connecting wirelessly to other WDS-capable APs (peer APs). By default, all WDS profiles are disabled.
Click on the Wireless button on the main menu. Select the Repeater Settings tab. Choose WDS as the Repeater Type. Choose the desired WDS profile:
(a) Enable WDS. (b) Enter the Remote AP MAC Address (peer AP) and then Click SAVE.
If you are using another EAP737 as the peer AP, simply repeat the above-mentioned steps to configure another peer AP(s).
Copyright © 4IPNET, INC. All rights reserved.
Quick Installation Guide
After EAP737's network configuration is completed, please remember to change the IP Address of your PC Connection Properties back to its original settings in order to ensure that your PC functions properly in its real network environments.
It is strongly recommended to make a backup copy of your configuration settings. For further configuration and backup information, please refer to the User’s Manual.
Congratulations!
Now, 4ipnet EAP737 is installed and configured successfully.
EAP737 Enterprise Access Point ENGLISH
P/N: V10020160811
Copyright © 4IPNET, INC. All rights reserved.
Loading...