4IPNET 150001 User Manual

Loading...

Product Handbook

EAP705 V1.00

Enterprise Access Point

4IPNET 150001 User Manual

Product Handbook

EAP705 Enterprise Access Point ENGLISH

Copyright Notice

This document is protected by USA copyright laws and other laws. Besides, the document is the property of 4IPNET, INC. You may not copy, reproduce, distribute, publish, display, perform, or modify any part of this publication in any form or by any means without prior written permission from 4IPNET, INC. You may not alter or remove any copyright or other notice from copies of the content. All other brand and product names are claimed or registered marks of their respective companies or organizations.

All rights reserved.

To download up-to-date version, please visit www.4ipnet.com.

Copyright © 4IPNET, INC. All rights reserved.

i

Product Handbook

EAP705 Enterprise Access Point ENGLISH

FCC CAUTION

This equipment has been tested and proven to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

---Reorient or relocate the receiving antenna.

---Increase the separation between the equipment and receiver.

---Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

---Consult the dealer or an experienced radio/TV technician for help.

The device contains a low power transmitter which will send out Radio Frequency (RF) signal when transmitting. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1)This device may not cause harmful interference, and

(2)This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Copyright © 4IPNET, INC. All rights reserved.

ii

Product Handbook

EAP705 Enterprise Access Point ENGLISH

CE CAUTION

Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive) for

European Community, Switzerland, Norway, Iceland, and Liechtenstein

Model: EAP705

For 2.4 GHz radios, the device has been tested and passed the requirements of the following standards, and hence fulfills the EMC and safety requirements of R&TTE Directive within the CE marking requirement.

Radio: EN 300.328:

EMC: EN 301.489-1, EN 301.489-17,

EMC: EN 55022 Class B, EN 55024:+ A1 + A2 including the followings: EN 61000-3-2, EN 61000-3-3.

EN 61000-4-2, EN 61000-4-3, EN 61000-4-4, EN 61000-4-5, EN 61000-4-6, EN 61000-4-11

Safety: EN 60950-1 + A11,

Caution:

This declaration is only valid for configurations (combinations of software, firmware, and hardware) provided and supported by 4ipnet Inc. The use of software or firmware not provided and supported by 4ipnet Inc. may result in the equipment no longer being compliant with the regulatory requirements.

European standards dictate maximum radiated transmit power of 100mW EIRP and frequency range 2.400-2.4835 GHz. This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be restricted to certain frequencies and/or may require a license for operation. Contact your local regulatory authority for compliance.

Taiwan NCC Statement

 

NCC

 

 

:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

5.25 ~ 5.35

 

 

 

 

 

Copyright © 4IPNET, INC. All rights reserved.

 

iii

Product Handbook

Preface

The 4ipnet EAP705 Wall Jack Access Point is an on-the-wall as well as a ceiling-mounted dual radio Wi-Fi IEEE 802.11b/g/n + a/n/ac 2 X 2 MIMO access point, designed to blend into a working or a living environment practically and elegantly with its simplistic yet sleek design.

The compact EAP705 in a small form factor lays snug in a standard wall outlet box. Its side panel features LED status indicators and two RJ45 ports. It has the interfaces to serve both wireless and wired LAN access. The RJ45 pass-through port allows phone or IP-based devices to pass through EAP705 without the need for additional outlets.

When coupled with the 4ipnet WHG series Controller, the EAP705 supports Tunnel-based AP Management, and comes with all standards demanded by enterprise applications, including business-grade security (802.1X, WPA and WPA2), and multiple ESSIDs with VLAN tags to separate the traffics of different departments. A centralized WLAN management allows enterprises and organizations to support a wide array of value added applications, such as load balancing, bandwidth control, and access control. The patent-pending 4ipWES (Press-n-Connect) technology bridges multiple EAP705s at the touch of a button, which enables a quick and automatic WDS Easy Setup by pressing the WES button on EAP705. Extending wireless network coverage is a breeze, be it across conference rooms or along hallways.

EAP705’s high performance, security and optimal invisibility make it a perfect choice of wireless connectivity for your business.

EAP705 Enterprise Access Point ENGLISH

Package Contents

1.4ipnet EAP705 x 1

2.Quick Installation Guide (QIG) x 1

3.Power Adapter (DC 12V) x 1 (Optional)

4.Mounting Screws x 2

5.Mounting Panel x 1

6.Mounting Plate Lock Tool x 1

It is recommended to keep the original packing material for possible future shipment when repair or maintenance is required. Any returned product should be packed in its original packaging to prevent damage during delivery.

Copyright © 4IPNET, INC. All rights reserved.

1

+ 11 hidden pages