3B Scientific Monocular Course Microscope 200 LED User Manual

3B SCIENTIFIC® PHYSICS

Monocular Course Microscope Model 200 LED (115 V) 1013364
Monocular Course Microscope Model 200 LED (230 V) 1013142

Instruction Manual

07/13 ALF

1 Eyepiece
2 Tube
3 Revolver with objectives
4 Specimen clips
5 Object stage
6 Condensor with iris

diaphragm and filter holder
7 Lamp housing
8 Illumination control
9 Mains switch
10 Adjustment knob for fine

focusing
11 Adjustment knob for coarse

focusing
12 Lock screw for object stage
13 Head lock screw
14 Stand

1. Safety notes

• For power supply use only electrical sockets

with ground contact.

2. Description, technical data

The monocular course microscope allows two­dimensional viewing of objects (thin sections of
plant or animal specimen) in 40x to 400x magni­fication.

The microscope 1013364 is for operation with a
mains voltage of 115 V (±10%), and the
1013142 unit is for operation with 230 V (±10%).

Stand: Robust, all metal stand with arm perma­nently connected to the base. Focussing by
means of separate knobs for coarse and fine
adjustment located on either side of the stand

and operated by rack and pinion drive with
dovetail teeth, adjustable stopper for protecting
the object stage and objective

Tube: Monocular inclined 45°, head rotation
360°

Eyepiece: Widefield eyepiece WF 10x 18 mm
Objectives: Revolver with 3 DIN achromatic

objectives 4x / 0.10, 10x / 0.25, 40x / 0.65 (with
specimen protection)

Magnification: 40x, 100x, 400x
Object stage: 127 x 132 mm

2

with 2 specimen

clips
Illumination: Adjustable LED lighting integrated

in base
Power supply: Via plug-in power supply 6 V

DC, 200 mA
Mains connection: 1013364: 115 V, 50/60 Hz;

1013142: 230 V, 50/60 Hz

1

Condenser: Condenser N.A. 0.65, iris dia­phragm, filter holder and blue filter

Dimensions: 220 x 148 x 356 mm³ approx.
Weight: 4 kg approx.

3. Unpacking and assembly

The microscope is packed in a molded styro­foam container.

• Take the container out of the carton remove

the tape and carefully lift the top half off the
container. Be careful not to let the optical
items (objectives and eyepieces) drop down.

• To avoid condensation on the optical com-

ponents, leave the microscope in the original
packing to allow it to adjust to room tem­perature.

• Using both hands (one around the pillar and

one around the base), lift the microscope
from the container and put it on a stable
desk.

• The objectives will be found within individual

protective vials. Install the objectives into the
microscope nosepiece from the lowest
magnification to the highest, in a clockwise
direction from the rear.

• Put the head onto the top of the stand and

tighten the head-lock-screw. Insert the eye­piece into the tube.

4. Operation

• Set the microscope on a level table.

• Place the object to be observed in the center

of the object plate. Use the clips to fasten it
into place. Make certain that the specimen is
centered over the opening in the stage.

• Connect the mains cable to the net and turn

on the switch to get the object illuminated.

• Make certain that the specimen is centered

over the opening in the stage.

• To obtain a high contrast, adjust the back-

ground illumination by means of the iris dia­phragm and the variable illumination control.

• Rotate the nosepiece until the objective with

the lowest magnification is pointed at the
specimen. There is a definite “click” when
each objective is lined up properly.

NOTE: It is best to begin with the lowest power
objective. This is important to reveal general
structural details with the largest field of view
first. Than you may increase the magnification
as needed to reveal small details.

To determine the magnification at which you are
viewing a specimen, multiply the power of the
eyepiece by the power of the objective.

• Adjust the coarse-focusing-knob which

moves the stage up until the specimen is fo­cused. Be careful that the objective does not
make contact with the slide at any time. This
may cause damage to the objective and/or
crack your slide.

• Adjust the fine-focusing-knob to get the im-

age more sharp and more clear.

• Colour filters may be inserted into the filter

holder for definition of specimen parts.
Swing the filter holder out and insert colour
filters.

• Always turn off the light immediately after

use.

• Be careful not to spill any liquids on the mi-

croscope.

• Do not mishandle or impose unnecessary

force on the microscope.

• Do not wipe the optics with your hands.

• Do not attempt to service the microscope

yourself.

5. Storage, cleaning, disposal

• Keep the microscope in a clean, dry and

dust free place.

• When not in use always cover the micro-

scope with the dust cover.

• Do not expose it to temperatures below 0°C

and above 40°C and a max. relative humid­ity of over 85%.

• Always unplug the mains plug before clean-

ing or maintenance.

• Do not clean the unit with volatile solvents or

abrasive cleaners.

• Do not disassemble objective or eyepieces

to attempt to clean them.

• Use a soft linen cloth and some ethanol to

clean the microscope.

• Use a soft lens tissue to clean the optics.

• The packaging should be disposed of at

local recycling points.

• Should you need to

dispose of the equip­ment itself, never throw
it away in normal do­mestic waste. Local
regulations for the dis­posal of electrical
equipment will apply.

3B Scientific GmbH • Rudorffweg 8 • 21031 Hamburg • Germany • www.3bscientific.com

Subject to technical amendments

© Copyright 2013 3B Scientific GmbH