2N Access Unit M Installation
Manual
v.1.0
www.2n.com
2N Access Unit M Installation Manual
Content
•
1. Product Overview
•
•
•
2. Description of Installation
•
•
•
•
•
3. Detection of 2N Access Unit M using 2N® Network Scanner
•
4. Factory Reset
•
5. Maintenance
•
6. Status Signaling
•
7. Technical Parameters
•
•
8. Supplementary Information
•
•
•
1.1 Components and Associated Products
1.2 Terms and Symbols
2.1 Before You Start
2.2 Mechanical Installation
2.3 Electric Installation
2.4 Extending Module Connection
7.1 General Drawings
8.1 General Instructions and Cautions
8.2 Troubleshooting
8.3 Directives, Laws and Regulations
2N Access Unit M Installation Manual
1. Product Overview
Here is what you can find in this section:
•
1.1 Components and Associated Products
•
1.2 Terms and Symbols
Basic Features
2N Access Unit M is an elegant and reliable access IP system equipped with a number of useful
functions.
2N Access Unit M is a single-module access system available in several versions.
All the 2N Access Unit M versions include an integrated card reader module, which helps
control access using an RFID card. With additional software settings, you can use the card to
control more functions than just door lock switching too.
The 2N Access Unit M keypad versionhelps you control the electric lock switch by entering a
valid numeric code via the numeric keypad. With additional software settings, you can use the
numeric code to control more functions than just door lock switching too.
The 2N Access Unit M Bluetooth version helps you control the lock switch using the 2N®Mobile
Key application installed in your smartphone.
2N Access Unit M is designed as a robust, mechanically resistant IP55-rated access system,
which withstands any weather conditions without requiring additional accessories.
The installation of 2N Access Unit M is very easy. All you have to do is connect the system to
your LAN via a mains cable. Feed the access system either from a 12V power supply or your PoE
supporting LAN.
To configure 2NAccess Unit M use a PC equipped with any Internet browser. Use2N®Access
Commander to bulk manage extensive access system installations easily.
Advantages of Use
•
Elegant mullion design
•
Weather resistance (IP 55)
•
Easy wall (surface) mounting (brick/pasterboard walls, door frames)
•
Integrated electric lock switches with wide setting options
•
Integrated RFID card reader module
•
Bluetooth module version
•
Backlit touch keypad version
•
LAN (PoE) or external 12V power supply
•
Configuration using web interface
•
HTTP server for API configuration
•
SNTP client for time synchronization
•
SMTP client for email sending, Picture to Email feature
2N Access Unit M Installation Manual
•
TFTP/HTTP client for automated firmware and configuration upgrade and update
1.1 Components and Associated Products
Main Units
2N Part No.
916112
Axis Part No.
02393-001
•
2N® Access Unit M 13.56 MHz, NFC ready
•
is used for reading RFID cards in the 13.56 MHz bandwidth with the
NFC support. Combining an access reader and a controller, the
device is used for access control inside and outside of buildings.
•
The following RFID cards can be read:
•
ISO14443A (Mifare, DESFire)
•
PicoPass (HID iClass)
•
Felica
•
ST SR(IX)
•
2N® Mobile Key
2N Access Unit M Installation Manual
Main Units
2N Part No.
916114
Axis Part No.
02394-001
2N Part No.
916115
Axis Part No.
02395-001
•
2N® Access Unit M RFID 125 kHz, 13.56 MHz, NFC
•
is used for reading RFID cards in the 125 kHz and 13.56 MHz
bandwidths with the NFC support. Combining an access reader and
a controller, the device is used for access control inside and outside
of buildings.
•
The following RFID cards can be read:
•
EM4xxx
•
ISO14443A (Mifare, DESFire)
•
PicoPass (HID iClass)
•
Felica
•
ST SR(IX)
•
2N® Mobile Key
•
2N® Access Unit M Bluetooth & RFID 125 kHz, 13.56 MHz, NFC
•
is used for reading RFID cards in the 125 kHz and 13.56 MHz
bandwidths with the NFC support. Combining an access reader, a
Bluetooth module and a controller, the device is used for access
control inside and outside of buildings.
•
The following RFID cards can be read:
•
EM4xxx
•
ISO14443A (Mifare, DESFire)
•
PicoPass (HID iClass)
•
Felica
•
ST SR(IX)
•
2N® Mobile Key
2N Access Unit M Installation Manual
Main Units
2N Part No.
916116
Axis Part No.
02396-001
License
•
2N® Access Unit M Touch Keypad & RFID 125 kHz, 13.56 MHz, NFC
•
is used for reading RFID cards in the 125 kHz and 13.56 MHz
bandwidths with the NFC support. Combining an access reader, a
touch keypad and a controller, the device is used for access control
inside and outside of buildings.
•
The following RFID cards can be read:
•
EM4xxx
•
ISO14443A (Mifare, DESFire)
•
PicoPass (HID iClass)
•
Felica
•
ST SR(IX)
•
2N® Mobile Key
2N Part No.
916012
Axis Part No.
01369-001
2N Part No.
9160401
Axis Part No.
02000-001
•
2N Access Unit NFC license
•
2N Access Unit Lift module license
2N Access Unit M Installation Manual
Electric Locks
Part No. 932071E BEFO 11211
Part No. 932081E BEFO 11221 with momentum pin
•
•
12 V / 230 mA DC
•
low consumption
•
•
12 V / 230 mA DC
•
low consumption
•
A very short electric pulse is enough to put the lock in the
OPEN position and unlock the door. After passage, the
lock gets in the CLOSED (relax) position again.
Part No. 932091E BEFO 11211MB with mechanical blocking
•
•
12 V / 230 mA DC
•
low consumption
•
You can set the lever mechanically into the OPEN or
CLOSED position. When OPEN, the lock is constantly
open, when CLOSED, it is a standard lock.
2N Access Unit M Installation Manual
Electric Locks
Part No. 932061E BEFO 11211MB with momentary pin, mechanical
Part No. 932072E BEFO 31211
•
blocking
•
low consumption
•
12 V / 230 mA DC
•
A regular lock with a built-in contact to indicate whether
the door is open or closed.
•
•
fail safe
•
12 V / 170 mA DC
•
The reverse lock is closed when electricity is switched
on. When electricity is interrupted, the lock is opened.
Part No. 932062E BEFO321211
Tip
•
FAQ: Electric locks – Differences between locks for 2N IP access systems
•
•
•
•
•
fail-safe plus door signaling
12 V / 170 mA
The reverse lock is closed when electricity is switched
on. When electricity is interrupted, the lock is opened.
It contains a built-in contact to indicate whether the
door is open or closed.
2N Access Unit M Installation Manual
Power Supply
Part Numbers
91378100E
91378100US
Part Nos.
91341482E
91341482US
•
PoE injector – without cable
•
PoE injector – with EU cable
•
PoE injector – with US cable
•
For intercom supply via Ethernet cable where the PoE switch is absent.
•
12 V / 1 A adapter
•
A stabilized power supply needs to be used where no PoE is available.
Part
No.932928
Additional Modules
2N Part No.
9159010
Axis Part No.
01386-001
•
12 V transformer
•
for electric lock
•
Security Relay
•
A handy add-on that significantly enhances door entry security
Prevents lock tampering. Installed between the intercom, from which
it is also supplied, and the lock to be controlled.
2N Access Unit M Installation Manual
Additional Modules
Part No. 9159013 Departure button
2N Part No.
9159012
Axis Part No.
01388-001
•
•
Connects the logic input for door unlocking from inside the building.
•
Magnetic door contact
•
Set for installation on a door, enabling the status of door opening to
be ascertained. Used when the intercom is used for door protection,
to detect when the door is not closed or forced open.
2N Part No.
9134173
Axis Part No.
01384-001
•
RFID card, Mifare Classic 1k, 13.56 MHz
2N Access Unit M Installation Manual
Additional Modules
2N Part
No.9134174
Axis Part No.
01385-001
2N Part
No.9134165E
Axis Part No.
01395-001
•
RFID fob, Mifare Classic 1k, 13.56 MHz
•
RFID card, type EM4100, 125 kHz
2N Part
No.9134166E
Axis Part No.
01396-001
•
RFID fob, type EM4100, 125 kHz
2N Access Unit M Installation Manual
Additional Modules
2N Part No.
9137420E
Axis Part No.
01399-001
2N Part No.
9137421E
Axis Part No.
01400-001
•
External RFID card reader connectable to a PC via a USB
interface.
•
Suitable for system administration and adding of EM41xx cards (125
kHz) via a web interface or 2N® Access Commander.
•
USB Reader of 13.56 MHz, 125 kHz RFID Cards and NFC/HCE
devices
•
External RFID card reader connectable to a PC via a USB interface.
Suitable for system administration and adding 13.56 MHz, 125 kHz
cards and Android platform devices supporting NFC/HCE using 2N IP
intercom web interface or 2N® Access Commander. It reads the
same types of cards and devices as card readers in2N IP intercoms.
•
13.56 MHz/ISO/IEC 14443AMifare Classic 1k & 4k, DESFire EV1,
Mini, Plus S&X, Ultralight, Ultralight C
•
13.56 MHz/ISO/IEC14443B CEPAS, HID iCLASS (CSN only)
•
13.56/JIS X 6319Felica
•
ISO/IEC 18092 SmartPhone with NFC/HCE support, Android
version 6.0 Marshmallow and higher (2N®Mobile Key required)
•
EMarine
2N Access Unit M Installation Manual
Additional Modules
2N Part No.
9137424E
Axis Part No.
01527-001
2N Part No.
9137410E
Axis Part No.
01397-001
•
SecuredUSB Reader of 13.56 MHz, 125 kHz RFID Cards and NFC/
HCE devices
•
External secured RFID card reader connectable to a PC via a USB
interface. Suitable for system administration and adding 13.56 MHz,
125 kHz cards and Android platform devices supporting NFC/HCE
using the 2N IP intercom web interface or 2N® Access Commander.
It reads the same types of cards and devices as card readers in2N IP
intercoms.
•
13.56 MHz/ISO/IEC 14443AMifare Classic 1k & 4k, DESFire EV1,
Mini, Plus S&X, Ultralight, Ultralight C
•
13.56 MHz/ISO/IEC 14443B CEPAS, HID iCLASS (CSN or PAC ID)
•
13.56MHz/JIS X 6319Felica
•
ISO/IEC 18092 SmartPhone with NFC/HCE support, Android
version 6.0 Marshmallow and higher (2N®Mobile Key required)
•
EMarine
•
External IP relay – 1 output
•
A stand-alone IP device, which can be controlled from an IP intercom
via HTTP commands, which can thus control devices on unlimited
distance.
2N Part
No.9137411E
Axis Part No.
01398-001
•
External IP relay – 4 outputs, PoE
•
A stand-alone IP device, which can be controlled from an IP intercom
via HTTPcommands, which can thus control devices on unlimited
distance.
Loading...