Multiquip WM-90P, WM-90S User Manual

PARTS MANUAL

SERIES

MODEL WM-90S (STEEL) MODEL WM-90P (PLASTIC)

PLASTER AND MORTAR MIXER

(GASOLINE ENGINE/ELECTRIC MOTOR)

Revision #6 (03/04/08)

To find the latest revision of this publication, visit our website at: www.multiquip.com

THIS MANUAL MUST ACCOMPANYTHE EQUIPMENT AT ALLTIMES.

Engine exhaust and some of its constituents, and some dust created by power sanding, sawing, grinding, drillingandotherconstructionactivities contains chemicals known to the State of California to cause cancer, birth defects and other reproductive harm. Some examples of these chemicals are:

Leadfromlead-basedpaints.

Crystallinesilicafrombricks.

Cementandothermasonryproducts. Arsenicandchromiumfromchemically treatedlumber.

Your risk from these exposures varies, dependingonhowoftenyoudothistype of work. To reduce your exposure to these chemicals: ALWAYS work in a well ventilated area, and work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.

PAGE 2 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

WM-90 S/P PLASTER/MORTAR MIXER — TABLE OF CONTENTS

	MQ-WHITEMAN — WM-90S/P		HONDA GX240K1HA2 ENGINE
	Plaster/Mortar Mixer
			Air Cleaner Assembly........................................	30-31
	Here's How To Get Help ...........................................	2	Camshaft Assembly ..........................................	32-33
	Table Of Contents ....................................................	3	Carburetor Assembly ........................................	34-35
	Parts Ordering Procedures ......................................	4	Control Assembly ..............................................	36-37
	Explanation of Code In Remarks Column................	6	Crankcase Cover Assembly..............................	38-39
	Suggested Spare Parts ............................................	7	Crankshaft Assembly ........................................	40-41
			Cylinder Barrel Assembly ..................................	42-43
	Component Drawings		Cylinder Head Assembly ...................................	44-45
			Fan Cover Assembly	46-47
	Nameplate and Decals	8-9
			Flywheel Assembly	48-49
	Frame Assembly	10-11
			Muffler Assembly	50-51
	Paddle Shaft Assembly	12-13
			Fuel Tank Assembly	52-53
	Steel Drum Assembly	14-15
			Ignition Coil	54-55
	Plastic Drum Assembly	16-17
			Piston Assembly	56-57
	Drum & Paddle Shaft Complete Assy. (Poly)	18-19
			Recoil Starter	58-59
	Drum & Paddle Shaft Complete Assy. (Steel)	20-21
			Gear Reduction Assembly	60-61
	Axle Assembly	22-23
			Label Assembly	62-63
	Engine Assembly	24-25
	Electric Motor Assembly....................................	26-27	Terms and Conditions of Sale — Parts	64
	Cabinet Assembly	28-29

Specifications and are subject to change without notice.

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 3

www.multiquip.com

PARTS ORDERING PROCEDURES

Ordering parts has never been easier!

Choose from three easy options:

Best Deal! Order via Internet (Dealers Only):

Orderpartson-lineusingMultiquip’sSmartEquipwebsite!

■View Parts Diagrams

■Order Parts

■Print Specification Information

Goto www.multiquip.com and click on

Order Parts to log in and save!

Effective:

January 1st, 2006

If you have an MQ Account, to obtain a Username and Password, E-mail us at: [e-mail].

To obtain an MQ Account, contact your District Sales Manager for more information.

Use the internet and qualify for a 5% Discount on Standard orders for all orders which include complete part numbers.*

Note: Discounts Are Subject To Change

Order via Fax (Dealers Only):

Fax your order in and qualify for a 2% Discount

All customers are welcome to order parts via Fax.

on Standard orders for all orders which include

Domestic (US) Customers dial:

complete part numbers.*

1-800-6-PARTS-7 (800-672-7877)

Note: Discounts Are Subject To Change

Order via Phone: Domestic (US) Dealers Call:

1-800-427-1244

Non-Dealer Customers:

International Customers should contact

Contact your local Multiquip Dealer for

their local Multiquip Representatives for

parts or call 800-427-1244 for help in

Parts Ordering information.

locating a dealer near you.

When ordering parts, please supply:

	Dealer Account Number	Specify Preferred Method of Shipment:
	Dealer Name and Address	UPS/Fed Ex	DHL
	Shipping Address (if different than billing address)	■ Priority One	Truck
		■ Ground
	Return Fax Number
		■ Next Day
	Applicable Model Number
		■ Second/ThirdDay

Quantity, Part Number and Description of Each Part

All orders are treated asStandard Orders andwillshipthesamedayifreceivedprior to 3PM PST.

WE ACCEPT ALL MAJOR CREDIT CARDS!

PAGE 4 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

NOTE PAGE

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 5

EXPLANATION OF CODE IN REMARKS COLUMN

The following section explains the different symbols and remarks used in the Parts section of this manual. Use the help numbers found on the back page of the manual if there are any questions.

The contents and part numbers listed in the parts section are subject to change without notice. Multiquip does not guarantee the availibility of the parts listed.

Sample Parts List:

NO.	PART NO.	PART NAME	QTY.	REMARKS
1	12345	BOLT ......................	1 ......	INCLUDES ITEMS W/*
2*		WASHER, 1/4 IN. .............		NOTSOLDSEPARATELY
2*	12347	WASHER, 3/8 IN. ...	1 ......	MQ-45T ONLY
3	12348	HOSE ...................	A/R ....	MAKE LOCALLY
4	12349	BEARING ...............	1 ......	S/N 2345B AND ABOVE

NO. Column

Unique Symbols - All items with same unique symbol (*, #, +, %, or >) in the number column belong to the same assembly or kit, which is indicated by a note in the “Remarks” column.

Duplicate Item Numbers - Duplicate numbers indicate multiple part numbers are in effect for the same general item, such as different size saw blade guards in use or a part that has been updated on newer versions of the same machine.

When ordering a part that has more than one item number listed, check the remarks column for help in determining the proper part to order.

PART NO. Column

Numbers Used - Part numbers can be indicated by a number, a blank entry, or TBD.

TBD (To Be Determined) is generally used to show a part that has not been assigned a formal part number at time of publication.

A blank entry generally indicates that the item is not sold separately or is not sold by Multiquip. Other entries will be clarified in the “Remarks” Column.

QTY. Column

Numbers Used - Item quantity can be indicated by a number, a blank entry, or A/R.

A/R (As Required) is generally used for hoses or other parts that are sold in bulk and cut to length.

A blank entry generally indicates that the item is not sold separately. Other entries will be clarified in the “Remarks” Column.

REMARKS Column

Some of the most common notes found in the “Remarks” Column are listed below. Other additional notes needed to describe the item can also be shown.

Assembly/Kit - All items on the parts list with the same unique symbol will be included when this item is purchased.

Indicated by:

“INCLUDES ITEMS W/(unique symbol)”

Serial Number Break - Used to list an effective serial number range where a particular part is used.

Indicated by:

“S/N XXXXX AND BELOW” “S/N XXXX AND ABOVE” “S/N XXXX TO S/N XXX”

Specific Model Number Use - Indicates that the part is used only with the specific model number or model number variant listed. It can also be used to show a part is NOT used on a specific model or model number variant.

Indicated by: “XXXXX ONLY”

“NOT USED ON XXXX”

“Make/Obtain Locally” - Indicates that the part can be purchased at any hardware shop or made out of available items. Examples include battery cables, shims, and certain washers and nuts.

“Not Sold Separately” - Indicates that an item cannot be purchased as a separate item and is either part of an assembly/kit that can be purchased, or is not available for sale through Multiquip.

PAGE 6 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

WM-90S/P MIXER — SUGGESTED SPARE PARTS

WM-90P/S PLASTER AND MORTAR MIXER 1 TO 3

UNITSWITH HONDA GX240K1HA2 ENGINE

				Part numbers on this
Qty....	P/N ......................	Description	NOTE	Suggested Spare Parts List
6 .......	505834 ................	V-BELT A36 HONDA ENGINE		may supercede/replace the P/
6 .......	491112 ................	V-BELT A40 ELECTRIC MOTOR		N's shown in the test pages of
2	EM914288	OIL SEAL, AXLE
				this manual.
4	EM903113	BEARING, CONE, AXLE
4 .......	EM903112 ...........	BEARING, CUP, AXLE
2 .......	20654-001 ...........	SEAL, PADDLE SHAFT (BLACK)
2 .......	530029 ................	RING, RETENTION
2 .......	20104-002 ...........	SEAL, SHAFT URETHANE (YELLOW)
3 .......	17210ZE2515 ......	ELEMENT, AIR CLEANER
3 .......	9807956846.........	SPARK PLUG
1 .......	28462ZE2W11 .....	ROPE, RECOIL STARTER
1 .......	17620ZH7023 ......	CAP, FUEL TANK
2 .......	EM200863 ...........	KIT, WIPER BLADES (STEEL DRUM)
2 .......	EM204625 ...........	KIT, WIPER BLADES (PLASTIC DRUM)

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 7

WM-90S/P MIXER — NAMEPLATE AND DECALS

NAMEPLATE AND DECALS

PAGE 8 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

WM-90S/P MIXER — NAMEPLATE AND DECALS

NAMEPLATE AND DECALS
NO	PART NO	PART NAME	QTY.	REMARKS
1	DCL151	DECAL, TOWING INSTRUCTIONS	2
2	EM948630	DECAL, PUSH TO STOP	1
3	CIPDCL160	DECAL, CRUSH WARNING	2
4	515275	DECAL, WHITEMAN LOGO (SMALL)	3
5	504713	DECAL, SAFETY INSTRUCTIONS	1
6	35137	DECAL, WARNING READ	1
7	504714	DECAL, WHITEMAN LOGO (LARGE)	3
9	513479	DECAL, WARNING SAFETY GRATE	1
9	DCL335	DECAL, CRUSH WARNING SAFETY GRATE	1
10	DCL280	DECAL, WARNING DUMP HANDLE	1
11	513522	DECAL, DRUM LOCK	1
12	13118	DECAL, POWDER COATED	1
13		NAMEPLATE........................................................	1 .........	CONTACT PARTS DEPT.

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 9

WM-90S/P MIXER — FRAME ASSY.

FRAME ASSY.

PAGE 10 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

WM-90S/P MIXER — FRAME ASSY.

FRAME ASSY.
NO.		PART NO.	PART NAME	QTY.	REMARKS
1		514842	LOCK PIN UNIT	1
2		491692	COTTER PIN	1
3		530023	SPRING LOCKING PIN	1
4		507444	WASHER, FLAT 3/4"	1
5		514835	MAIN FRAME	1
8		EM963692	BOLT 1/2" UNC 1-1/2"	6
9		492584	NUT, LOCK 1/2"	6
10		514802	AXLE, UNIVERSAL	1
11		10176	LOCK NUT 1/2" NC	1
12		EM124	BOLT 1/2"-13 X 4 G5	1
13*			SAFETY CHAIN	1
14*		01004	CONNECTOR LINK .....................................................	2 ...................	BEFORE JANUARY 2006
14*	*	01004	CONNECTOR LINK .....................................................	1 ...................	AFTER JANUARY 2006
14A		516580	CLEVIS SAFETY HOOK ............................................	1 ...................	AFTER JANUARY 2006
15		13363KIT	CHAIN AND LINK KIT .................................................	1 ...................	INCLUDES ITEMS W/*
16		HBC-1	BALL HITCH 2-INCH ...................................................	1 ...................	CONTACT UNIT SALES
17		HLC-1	LOOP HITCH ..............................................................	1 ...................	CONTACT UNIT SALES
18		HPC-1	PIN HITCH 1-INCH......................................................	1 ...................	CONTACT UNIT SALES

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 11

WM-90S/P MIXER — PADDLE SHAFT ASSY.

PADDLE SHAFT ASSY.

PAGE 12 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

WM-90S/P MIXER — PADDLE SHAFT ASSY.

PADDLE SHAFT ASSY.

NO.	PART NO.
1	514752
2	492584
3	EM200295
4	510721
5	EM200292
6	EM200296
7	504322
8	EM200297
9	EM200294
10*#	492367
11*#	EM923023
12#	EM507519
12*	EM200212
13*#	EM203432
14*#	2105164
1615*#	EM200293EM923343
17*#	EM203433
18#	EM507518
18*	EM200213
19	EM200863
19	EM204625

PART NAME	QTY.	REMARKS
PADDLE SHAFT	1
NUT, LOCK 1/2"	6
PADDLE ARM, CENTER ENGINE END	1
BOLT, 1/2 " X 6" G5	2
INSERT, PADDLE ARM	4
PADDLE ARM, ENGINE END	1
WASHER, FLAT 1/2"	6
U-BOLT, END PADDLES	2
PADDLE ARM, CENTER TOW END	1
SCREW, HHC 5/16-18 X 1-3/4 G5	14
WASHER, FLAT 5/16"	28
BLADE, SIDE, POLY ..................................................	4 ...................	PLASTIC DRUM
BLADE, SIDE, RUBBER .............................................	4 ...................	STEEL DRUM
BLADE, SIDE, SCRAPPER ........................................	4 ...................	STEEL & PLASTIC DRUM
NUT, HEX 5/16" NC G5	14
WASHER, LOCK 5/15"	14
PADDLE ARM, TOW END	1
BLADE ,SCRAPPER END ..........................................	4 ...................	STEEL & PLASTIC DRUM
BLADE, PLASTIC END ..............................................	4 ...................	PLASTIC DRUM
BLADE, RUBBER END ...............................................	4 ...................	STEEL DRUM
KIT, WIPERS, SCRAPPERS & HDWARE...................	1 ...................	INCLUDES ITEMS W/*
STEEL DRUM
KIT, WIPERS, SCRAPPERS & HDWARE...................	1 ...................	INCLUDES ITEMS W/#
PLASTIC DRUM

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 13

WM-90S/P MIXER — STEEL DRUM ASSY.

STEEL DRUM ASSY.

PAGE 14 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

WM-90S/P MIXER — STEEL DRUM ASSY.

STEEL DRUM ASSY.
NO.	PART NO.	PART NAME	QTY.	REMARKS
1	530028	DRUM BEARING BRACKET	2
2	3249	CAP, DUST	1
3	20561-001	BEARING SEALED ...........................................	2 ...........	SET SCREWS AND BEARING
		..........................................................................................		COLLAR CANNOT BE PURCHASED
4	491008	CAP,..........................................................................................GREASE FITTING	2	SEPARATELY.
5	EM916019	FITTING, GREASE	2
6	EM969013	NUT, LOCK 3/8"	12
7	3019092	WASHER, FLAT 3/8"	4
8	514778	TRUNNION HUB	2
9	513453	ROLL PIN 3/16" X 3/4"	2
10	20654-001	SEAL, SHAFT (BLACK)	2
11	530029	RING, RETENTION	2
12	20104-002	SEAL, SHAFT URETHANE (YELLOW)	2
13	504943	BOLT, FHCS 3/8" NC X 2" G5	8
14	514786	DRUM, STEEL	1
15	492484	SET SCREW	2
16	530043	MAIN GEAR	1
17	501016	KEY, 3/8" X 88 MM	1
18	17985-012	CARRIAGE BOLT 3/8-16 X 1-1/2"	4
19	514752	SHAFT, PADDLE	1
20	492600	WASHER, FLAT 1/2"	4
21	514945	LIFT BAR	1
22	EM925191	PIN, COTTER	1
23	514946	GRATE	1
24	505070	PIN, COTTER	2
25	492556	HEX NUT 1/2" G5	2
26	6109180	WASHER, LOCK 1/2"	2
27	EM963692	BOLT 1/2" UNC 1-1/2"	2
28	EM963102	CAPSCREW, HHCS 1/2" NC X 1-1/4"	1
29	492584	NUT, LOCK1/2" NC	1
30	201537	HANDLE DUMP	1
31	EM98195	GRIP, DUMP HANDLE	1

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 15

WM-90S/P MIXER — PLASTIC DRUM ASSY.

PLASTIC DRUM ASSY.

PAGE 16 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

WM-90S/P MIXER — PLASTIC DRUM ASSY.

PLASTIC DRUM ASSY.
NO.	PART NO.	PART NAME	QTY.	REMARKS
1	530028	DRUM BEARING BRACKET	2
2	3249	CAP, DUST	1
3	20561-001	BEARING SEALED ...........................................	2 ...........	SET SCREWS AND BEARING
		..........................................................................................		COLLAR CANNOT BE PURCHASED
4	491008	CAP,..........................................................................................GREASE FITTING	2	SEPARATELY.
5	EM916019	FITTING, GREASE	2
6	EM969013	NUT, LOCK 3/8"	20
7	3019092	WASHER, FLAT 3/8"	6
8	514778	TRUNNION HUB	2
9	513453	ROLL PIN 3/16" X 3/4"	2
10	20654-001	SEAL, SHAFT (BLACK)	2
11	530029	RING, RETENTION	2
12	20104-002	SEAL, SHAFT URETHANE (YELLOW)	2
13	504943	BOLT, FHCS 3/8" NC X 2" G5	8
14	515052	DRUM, PLASTIC	1
15	492484	SET SCREW	2
16	530043	MAIN GEAR	1
17	500432	KEY, 3/8" X 88 MM	1
18	17985-012	CARRIAGE BOLT 3/8-16 X 1-1/2"	4
19	514752	SHAFT, PADDLE	1
20	492600	WASHER, FLAT 1/2"	1
21	514947	LIFT BAR	1
22	EM925191	PIN, COTTER	1
23	EM507417	GRATE, MOVEABLE	1
24	505070	PIN, COTTER	2
25	492556	HEX NUT 1/2" G5	2
26	6109180	WASHER, LOCK 1/2"	2
27	EM963610	BOLT 3/8" NC 1-1/4" G8	2
28	EM963102	CAPSCREW, HHCS 1/2" NC X 1-1/4"	1
29	492584	NUT, LOCK1/2" NC	1
30	EM201537	HANDLE DUMP	1
31	EM98195	GRIP, DUMP HANDLE	1
32	515033	RUBBER, GASKET	1
33	511910	BOLT 1/4" NC X 1-1/4" G5	8
34	2101428	NUT 1/4" NC	8
35	514989	U-SUPPORT PLASTIC DRUM	1
36	EM507416	GRATE, STATIONARY	1
37	0401450160	WASHER, FLAT 5/8"	1

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 17

WM-90 S/P MIXER — DRUM & PADDLE SHAFT COMPLETE ASSY.

DRUM AND PADDLE SHAFT COMPLETE ASSY. (PLASTIC DRUM)

PAGE 18 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)

WM-90 S/P MIXER — DRUM & PADDLE SHAFT COMPLETE ASSY.

DRUM AND PADDLE SHAFT COMPLETE ASSY. (PLASTIC DRUM)
NO.	PART NO.	PART NAME	QTY.	REMARKS
1	516064	DRUM AND SHAFT COMPLETE ASSY. ........... 1 ........... INCLUDES ITEMS LISTED BELOW:
	530028	DRUM BEARING BRACKET	2
	3249	CAP, DUST	1
	20561-001	BEARING SEALED	2
	491008	CAP, GREASE FITTING	2
	EM916019	FITTING, GREASE	2
	EM969013	NUT, LOCK 3/8"	20
	3019092	WASHER, FLAT 3/8"	6
	514754	TRUNNION HUB	2
	513453	ROLL PIN 3/16" X 3/4"	2
	20654-001	SEAL, SHAFT (BLACK)	2
	530029	RING, RETENTION	2
	20104-002	SEAL, SHAFT URETHANE (YELLOW)	2
	513452	BOLT 3/8" NC X 1/4" G5	8
	515052	DRUM, PLASTIC	1
	492484	SET SCREW	2
	530043	MAIN GEAR	1
	500432	KEY, 3/8" X 50 MM	1
	EM963057	CAPSCREW HHCS 3/8 X 1-1/2"	4
	514752	SHAFT, PADDLE	1
	EM507417	GRATE, MOVEABLE	1
	505070	PIN, COTTER	2
	492556	HEX NUT 1/2" G5	2
	6109180	WASHER, LOCK 1/2"	2
	EM963610	BOLT 3/8" NC 1-1/4" G8	2
	EM201537	HANDLE, DUMP	1
	15081	GRIP, DUMP HANDLE	1
	515033	RUBBER, GASKET	1
	511910	BOLT 1/4" NC X 1-1/4" G5	8
	2101428	NUT 1/4" NC	8
	514989	U-SUPPORT PLASTIC DRUM	1
	EM507416	GRATE, STATIONARY	1
	514752	PADDLE SHAFT	1
	492584	NUT, LOCK 1/2"	6
	EM200295	PADDLE ARM, CENTER ENGINE END	1
	510721	BOLT, 1/2 " X 6" G5	2
	EM200292	INSERT, PADDLE ARM	4
	EM200296	PADDLE ARM, ENGINE END	1
	504322	WASHER, FLAT 1/2"	6
	EM200297	U-BOLT, END PADDLES	2
	EM200294	PADDLE ARM, CENTER TOW END	1
	492367	SCREW, HHC 5/16-18 X 1-3/4 G5	14
	EM923023	WASHER, FLAT 5/16"	28
	13352	BLADE, SIDE, POLY	4
	EM203432	BLADE, SIDE, SCRAPPER	4
	2105164	NUT, HEX 5/16" NC G5	14
	EM923343	WASHER, LOCK 5/15"	14
	EM200293	PADDLE ARM, TOW END	1
	EM203433	BLADE ,SCRAPPER END	4
	507518	BLADE, PLASTIC END	4

WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08) — PAGE 19

WM-90 S/P MIXER — DRUM & PADDLE SHAFT COMPLETE ASSY.

DRUM AND PADDLE SHAFT COMPLETE ASSY. (STEEL DRUM)

PAGE 20 — WM-90 PLASTER/MORTAR MIXER — PARTS MANUAL — REV. #6 (03/04/08)