Alcatel-Lucent 1000 ADSL User Manual
Size:
2.84 Mb
Download

SAVE THESE IMPORTANT SAFETY

INSTRUCTIONS!

1.Read and understand all instructions.

2.Follow all warnings and instructions marked on the product.

3.Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

4.Do not use this product near water; for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.

5.This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your dealer or local power company.

6.Do not allow anything to rest on the power cord. Do not locate this product where the cord will be abused by persons walking on it.

7.Do not overload wall outlets and extension cords, as this can result in the risk of fire or electric shock.

8.To reduce the risk of electric shock, do not disassemble this product, buttake it to a qualified serviceman when service or repair work is required. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect reassembly can cause electric shock when the appliance is subsequently used.

9.Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

When the power supply cord or plug is damaged or frayed;

If liquid has been spilled into the product;

If the product has been exposed to rain or water;

If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions; improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to normal operation;

If the product has been dropped or the housing has been damaged;

If the product exhibits a distinct change in performance.

10.Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning.

11.Do not use the telephone to report a gas leak in the vicinity of the leak.

Contents

Note:

When using hyperlinks to navigate through this document, you may use either the "back" button of your reader software to return to the table of contents, or the bookmark, using the bookmark display button.

SECTION 1: QUICK START PROCEDURES

GETTING STARTED

Delivery Check

Placement of ADSL High Speed Modem

Wall-Mounting Option

Filter Installation

Determining Your Service Type

BRIDGED SERVICE

System Requirements

Hardware Installation

Accessing Online Services

POINT TO POINT SERVICE

System Requirements

Hardware Installation

Accessing Online Services

Windows 95/Windows 98 Dial-Up Procedures

Windows NT Dial-Up Procedures

ATM-25 SERVICE

System Requirements

Hardware Installation

Accessing Online Services

SECTION 2: DESCRIPTION OF FEATURES

MODEM CONNECTIONS

Connector Pinout

Power Supply

Visual Indicators

Subscriber Line Interface

Ethernet Interface

Single PC Configuration

Straight-Through Cable Layout

Multiple PC Configuration

Crossover Cable Layout

ATMF-25 Interface

NETWORK CONNECTIONS

Virtual Connections

ATM-Forum Interface

Ethernet Interface

ISP/Corporate Network Requirements

BRIDGED CONNECTIONS

Multiprotocol

Number of Machines Supported

Plug and Play

PC/Workstation Configuration

Bridged Service with Filtering

POINT TO POINT TUNNELING CONNECTIONS

Introduction

PPP/PPTP Network

Establishing PPP/PPTP Connections

Number of PPP/PPTP Connections Supported

LAN Protocols Supported

Known Limitations

ADVANCED CONFIGURATIONS

Overview

IP Parameters

Sample Configurations

Ping-of-Life Procedure

Ping-to-Defaults Procedure

CHANGING THE MODEM SETTINGS

Configuring the Browser

Accessing the ADSL Modem Interface

Welcome Page

Basic Configuration

Advanced Configuration

Bridge Configuration

Basic PPP/PPTP Configuration

Advanced PPP/PPTP Configuration

System Overview Page

REGULATORY INFORMATION

Environmental Conditions

Safety Standards

Power Supply

Conformance Declarations

Interference Information Part 15 of FCC Rules For Canadian Modem Users

Pour les Utilisateurs Canadiens de Modem TROUBLESHOOTING TIPS

SECTION 1: QUICK START PROCEDURES

This section of the 1000 ADSL High Speed Modem User’s Guide provides the basic instructions to install your modem and access online services as quickly as possible. Procedures include steps for correct placement of your modem, cable connections, and switching on the modem. These quick start procedures assume a single PC configuration using the modem's default settings.

A detailed description of features is provided in section 2 of this user's guide. Section 2 also provides a description of advanced configurations used in small office environments. Because the Alcatel high speed modem provides a user interface to your PC, you can change default settings of the modem to accommodate specific networking requirements.

GETTING STARTED

Delivery Check

Verify that the Alcatel 1000 High Speed Modem box contains all the components listed below:

ADSL high speed modem,

Power supply adapter with connecting cable,

Alcatel Data Cable (Category 5)

Wall-mountingtemplate,

Two wall plugs and two screws for wall-mountingoption, and

This user’s guide.

Placement of ADSL High Speed Modem

The ADSL high speed modem may be placed on an even, hard surface, such as a desk, or mounted on a wall. In either case, make sure the modem is near a power outlet, phone jack, and the PC to facilitate connections to these devices.

Wall-MountingOption

Part of the packaging is a wall-mountingtemplate. If you want to mount the modem on a wall, cut the template out and use it as follows (see figure 1).

1. Use template to mark positions of holes as indicated in table A.

 

Table A.

 

 

 

If you mount the

 

Mark positions of holes

modem on...

 

 

 

 

 

Left side of corner

Right side of corner

Area of wall away from corner

A1 and A2

B1 and B2

Either A1 and A2 or B1 and B2

2.Drill the marked holes with a 6-mm(0.24-in.)diameter drill bit to a minimum depth of 35 mm (1.38 in.).

3.Insert the wall plugs in the drilled holes.

4.Insert the screws in the wall plugs and tighten them, leaving at least 3 mm (0.12 in.) protruding.

5.Position the modem over the upper screw (A1 or B1) and pull the box down until you hear a click.

6.Rotate the modem toward the lower screw (A2 or B2) and push it until you hear a click.

Template

Corner

Figure 1. Wall-MountingInstructions

Filter Installation

To maintain normal phone service, a special filter must be installed in the Network Interface Device or NID, the gray box mounted on the outside of your home that terminates your phone connection. This filter, sometimes called a splitter, splits the voice (phone) signal from the ADSL (data) signal.

Set-upand installation charges for ADSL service typically include the filter installation. If you are not sure that the filter is installed, contact your service provider.