ZyXEL HLA3105 Owner's Manual

HLA3105 USER’S GUIDE

Box Contents

• One HLA3105

• One Ethernet Cable

•One Power Adaptor

•One User’s Guide

• One Warranty Card

Overview

The HLA3105 complies with HomePNA (Home Phoneline Networking Alliance, also known as HPNA) 3.1, a home networking technology for carrying data over existing coaxial cables and telephone wiring within the home.

The figure below shows your HLA3105 (a) connecting to a broadband modem/router (excluding cable modem/routers) for Internet access and a television. You can connect a second HLA3105 (b) into another coaxial outlet in your home and connect a computer for Internet access.

Connecting the HLA3105 to a Broadband Modem/Router

1. Use the included Ethernet cable to connect the ETHERNET port to your broadband modem/

router.

2. Use a coaxial cable to connect the IN connector to a coaxial outlet in your home.

3. Use another coaxial cable to connect the OUT connector to a television or set-top box.

4. Use the included power adaptor to connect the POWER connector to a power outlet.

Connecting the HLA3105 to a Computer

1. Use the included Ethernet cable to connect the ETHERNET port on the HLA3105 to a

computer.

2. Use a coaxial cable to connect the IN connector to a coaxial outlet in your home.

3. Use another coaxial cable to connect the OUT connector to a television or set-top box (optional).

4. Use the included power adaptor to connect the POWER connector to a power outlet.

LEDs

The following table describes the LEDs on the HLA3105.

LED Color Status Description

Power Green On The HLA3105 is receiving

power.

Off The HLA3105 is not receiving

power.

Quality Green On The transmission rate

through the coaxial connection is 160 Mbps or above.

Amber On The transmission rate

through the coaxial connection is between 160 Mbps and 96 Mbps.

Red On The transmission rate

through the coaxial connection is below 96 Mbps.

Off The HLA3105 is off.

LNK/ACT Green On The HLA3105 has a coaxial

connection.

Blinking The HLA3105 is sending or

receiving traffic over a coaxial cable.

Off The HLA3105 does not have

a coaxial connection.

Ethernet Green On The HLA3105 has an

Ethernet connection with a device (such as your computer).

Blinking The HLA3105 is sending or

receiving traffic through the Ethernet port.

Off The HLA3105 does not have

an Ethernet connection with a device (such as your computer).

The HLA3105 cannot connect to a cable modem/router at the time of writing.

12/2010 Version 1.9.5, Edition 1

HLA3105 USER’S GUIDE

Product Specifications

Dimensions 112 mm (W) x 106 mm (D) x 28.5 mm

(H) Device Weight 167 g Two Coaxial

Connectors

One RJ-45 Ethernet Port

Power Specification

Operating Environment

Storage Environment

Certifications HomePNA

Distance between wallmounting holes on device's base panel

Screw size for wall mounting

IN: connect to a coaxial outlet in the

home

OUT: connect to a TV or set-top box

Auto-negotiating: 10 Mbps or 100 Mbps

in either half-duplex or full-duplex mode.

Auto-crossover: Use either crossover or

straight-through Ethernet cables.

Input: 100 - 240 VAC 50/60 Hz

Output: 5V 1A DC

Temperature: 0 ºC ~ 40 ºC

Humidity: 20%~ 85% RH (non-

condensing)

Temperature: -30 ºC ~ 60 ºC

Humidity: 20%~ 95% RH (non-

condensing)

Safety

• CSA C22.2 No.60950-1

• UL 60950-1

• EN 60950-1

• IEC 60950-1

EMC

• European Union (CE mark):

EN55022 Class B (1998)

•North America:

FCC Part 15 (Class B)

75.8 mm

M4 Tap

Wall Mounting

It is recommended that you do NOT wall-mount the HLA3105. Wall-mounting kit is not included.

Complete the following steps to hang your HLA3105 on a wall.

See Product Specifications for the size of screws to use and how far apart to place them.

1. Select a position free of obstructions on a sturdy wall.

2. Drill two holes for the screws.

1 Be careful to avoid damaging pipes or

cables located inside the wall when drilling holes for the screws.

3. Do not insert the screws all the way into the wall. Leave a small gap of about 0.5 cm between the heads of the screws and the wall.

4. Make sure the screws are snugly fastened to the wall. They need to hold the weight of the HLA3105 with the connection cables.

5. Align the holes on the back of the HLA3105 with the screws on the wall. Hang the HLA3105 on the screws.

The following are dimensions of an M4 tap screw and masonry plug used for wall mounting. All measurements are in millimeters (mm).

Safety Warnings

• Do NOT use this product near water, for example, in a wet basement or near a swimming pool.

• Do NOT expose your device to dampness, dust or corrosive liquids.

• Do NOT store things on the device.

• Do NOT install, use, or service this device during a thunderstorm. There is a remote risk of electric shock from lightning.

• Connect ONLY suitable accessories to the device.

• Place connecting cables carefully so that no one will step on them or stumble over them.

• Always disconnect all cables from this device before servicing or disassembling.

• Do NOT open the device or unit. Opening or removing covers can expose you to dangerous high voltage points or other risks. ONLY qualified service personnel should service or disassemble this device. Please contact your vendor for further information.

• Use ONL Y an appropriate power adaptor or cord for your device. Connect it to the right supply voltage (for example, 110V AC in North America or 230V AC in Europe).

• Do NOT allow anything to rest on the power adaptor or cord and do NOT place the product where anyone can walk on the power adaptor or cord.

• Do NOT use the device if the power adaptor or cord is damaged as it might cause electrocution.

• If the power adaptor or cord is damaged, remove it from the device and the power source.

• Do NOT attempt to repair the power adaptor or cord. Contact your local vendor to order a new one.

• Do not use the device outside, and make sure all the connections are indoors. There is a remote risk of electric shock from lightning.

• Do NOT obstruct the device ventilation slots, as insufficient airflow may harm your device.

• Make sure that the cable system is grounded so as to provide some protection against voltage surges.

• Make sure to connect the cables to the correct ports.

• Your product is marked with this symbol, which is known as the WEEE mark. WEEE stands for Waste Electronics and Electrical Equipment. It means that used electrical and electronic products should not be mixed with general waste. Used electrical and electronic equipment should be treated separately.

www.zyxel.com

Declaration of Conformity

We, ZyXEL Communications Corp., located at No.6, Innovation Rd II, Science-Park, Hsin-Chu, 300, Taiwan, declare under our sole responsibility that the product:

Product information

Product Name : HomePNA 3.1 Coax Ethernet Bridge Model Number : HNA-101, HLA3105

Produced by

Company Name : ZyXEL Communications Corporation Company Add. : No. 6, Innovation Road II, Science-Park, Hsin-Chu, 300, Taiwan

to which this declaration relates, is in conformity with the following standards or other normative documents:

EN 55022:2006+A1: 2007 EN 55024:1998+A1: 2001+A2: 2003 EN 61000-3-2: 2006 EN 61000-3-3: 2008

Safety EN 60950-1: 2006 +A11: 2009

Following the provisions of 2004/108/EC; 92/31/EEC Directive; 93/68/EEC, 99/5/EEC , LVD 2006/95/EC, and ErP 2009/125/EC.

In accordance with Annex III of the Directive 1999/5/EC.

The TCF-File is located at:

Company Name : ZyXEL Communications Czech s.r.o. Company Address : Modranska 621, 143 01 Praha 4, Czech Republic

Person is responsible for marking this declaration:

Milan Baran VP Operations Name (Full Name) Position/ Title

2010-05-10

Date Legal Signature

COMMISSION REGULATION (EC) No 1275/2008 COMMISSION REGULATION (EC) No 278/2009

1/1

12/2010 Version 1.9.5, Edition 1