zyxel GS1100 User Manual

Download

Page 1

Quick Start Guide

GS1100 Series

Unmanaged Gigabit Ethernet Switch

Version 1.00 Edition 5, 09/2015

User’s Guide

www.zyxel.com

Page 2

IMPORTANT! READ CAREFULLY BEFORE USE. KEEP THIS GUIDE FOR FUTURE REFERENCE.

Screenshots and graphics in this book may differ slightly from your product due to differences in your product firmware or your computer operating system. Every effort has been made to ensure that the information in this manual is accurate.

•More Information Go to support.zyxel.com to find other information on the Switch

GS1100 Series User’s Guide

Page 3

Table of Contents

Table of Contents .................................................................................................................................3

Chapter 1

Getting to Know Your Switch...............................................................................................................4

1.1 Introduction ............................................................ ... .... ... ... ................................................................4

1.2 Features .......... ... .......................................... .... ... .......................................... ... ... ................................5

1.3 Applications ......................................... ... ... .......................................... ... .... .........................................6

1.3.1 Standalone Workgroup .................... ... .......................................... .... ... ... ... .... ... ... ... ... .... ............6

1.3.2 Bridging ........................................... ... .... ... ... .......................................... ... ................................6

1.4 Power Over Ethernet (PoE) ................................................................................................................7

Chapter 2

Hardware Description and Connection ..............................................................................................8

2.1 Rear Panel .......................................................................................................................................8

2.1.1 Rear Panel Power Connection ........... .... ... ... ... .... ... ... .......................................... ... ... .... ... ... ......8

2.2 Front Panel ................................... .... .......................................... ... ... ...................................................9

2.2.1 RJ-45 Auto-negotiating Ports ........................................... ... ... ... ... .... ... ... ... .... ... ... ... ... .... ... .........9

2.2.2 IEEE 802.3az EEE ....................................................................................................................9

2.2.3 SFP Slots (GS1100-24 and GS1100-10HP) ..................................................................... ... ...... 9

2.2.4 Front Panel Connections .............................................................. .... .......................................11

2.2.5 Front Panel LEDs ............................ ... .... ... ... .......................................... ... .... ... ... ... .................11

2.3 Hardware Installation ........................................................................................................................14

2.3.1 Wall Mounting ............... ... ... .... ... ... ... .......................................... ... .... .......................................14

2.3.2 Rack Mounting ................. ... .... ... .......................................... ... ... ... .... ... ....................................15

2.3.3 Mounting the Switch on a Rack ...............................................................................................16

Chapter 3

Troubleshooting..................................................................................................................................18

3.1 Improper Network Cabling and Topology ................................................... .......................................19

Appendix A Legal Information............................................................................................................20

Index ....................................................................................................................................................29

GS1100 Series User’s Guide

Page 4

CHAPTER 1

Getting to Know Your Switch

1.1 Introduction

This chapter describes the key features, benefits and applications of your Switch.

This User’s Guide covers the following models: GS1100-8HP, GS1100-16, GS1100-24, GS1100-24E and GS1100-10HP. The Switch is a 10/100/1000 Mbps multi-port switch that can be used to build high-performance switched workgroup networks. The Switch is a store-and-forward device that offers low latency for high-speed networking. The Switch is fanless and designed for workgroups, departments or backbone computing environments for small businesses.

Table 1 GS1100 Series Comparison Table

PORT/SWITCH DETAILS GS1100-8HP GS1100-16 GS1100-24 GS1100-24E GS1100-10HP

10/100/1000Base-T Ethernet ports 100/1000Base-X SFP slots 22

802.3AT PoE ports 4 8 One physical IEEE 802.3az ON/OFF button 11111 One power ON/OFF switch 1 1 1 1

8 162424 8

The GS1100-8HP has four GbE PoE ports that can supply power to the connected PoE powered devices.

The GS1100-10HP has eight GbE PoE ports that can supply power to the connected PoE powered devices.

The GS1100-24 and GS1100-10HP have two SFP slots for uplink connection. Use SFP transceivers in these slots for 100Mbps or 1Gbps connections to backbone Ethernet switches.

The Switch has a built-in algorithm that automatically assigns priority to received packets. It can operate in low power idle mode in compliance with IEEE 802.3az Energy Efficient Ethernet (EEE).

GS1100 Series User’s Guide

Page 5

Figure 1 Front Panel

GS1100-8HP

GS1100-16

GS1100-24

GS1100-24E

GS1100-10HP

Chapter 1 G etting to Know Your Switch

1.2 Features

The following are the essential features of the Switch.

• Conforms to IEEE 802.3, 802.3u, 802.3ab and 802.3x standards.

• Auto-negotiating 10/100/1000 Mbps Gigabit Ethernet (GbE) RJ-45 ports.

• Auto-sensing crossover for all 10/100/1000 Mbps Gigabit Ethernet (GbE) RJ-45 ports.

• Supports N-Way protocol for speed (10/100/1000 Mbps) and duplex mode (Half/Full) autodetection.

• Supports store-and-forward switching.

• Supports automatic address learning.

• Supports IEEE 802.3az EEE

• Supports IEEE 802.3af and IEEE 802.3at PoE standards (GS1100-8HP and GS1100-10HP)

• Full wire speed forwarding rate.

• Supports 802.1p CoS.

• Embedded 8K MAC address table providing 8000 MAC addresses entries.

GS1100 Series User’s Guide

Page 6

Chapter 1 Getting to Know Your Switch

1.3 Applications

This section provides two network topology examples in which the Switch is used.

1.3.1 Standalone Workgroup

In this application, the Switch is an ideal solution for small networks where rapid growth can be expected in the near future.

The Switch can be used standalone for a group of heavy traffic users. You can connect computers directly to the Switch’s port or connect other switches to the Switch.

In this example, all computers can share high-speed applications on the server. To expand the network, simply add more networking devices such as switches, routers, computers, print servers etc.

Figure 2 Standalone Workgroup Example

1.3.2 Bridging

With its large address table and high performance, the Switch is an ideal solution for department networks to connect to the corporate backbone or for connecting network segments.

The following figure depicts a typical segment bridge application of the Switch in an enterprise environment. The two networks (R&D and Sales), the standalone server and the computers can all communicate with each other and share all network resources.

Figure 3 Bridging Example

GS1100 Series User’s Guide

Page 7

Chapter 1 G etting to Know Your Switch

1.4 Power Over Ethernet (PoE)

The PoE function is available for GS1100-8HP and GS1100-10HP.

Ports 1 to 4 on the GS1100-8HP are IEEE 802.3at High Power over Ethernet (PoE) compliant and can supply power of up to 30W per Ethernet port and up to the total PoE power budget per Switch.

Ports 1 to 8 on the GS1100-10HP support both the IEEE 802.3af Power over Ethernet and IEEE

802.3at High Power over Ethernet standards. The ports supply power of up to 30W per Ethernet

port and up to the total PoE power budget per Switch.

The Switch is Power Sourcing Equipment (PSE) because it provides a source of power via its Ethernet ports. A powered device (PD) is a device such as an access point or an IP phone, that supports PoE (Power over Ethernet) so that it can receive power from another device through a 10/ 100/1000 Mbps Ethernet port.

In the figure below, the IP camera and IP phone get their power directly from the Switch. Aside from minimizing the need for cables and wires, PoE removes the hassle of trying to find a nearby electric outlet to power up devices.

Figure 4 Powered Device Examples

GS1100 Series User’s Guide

Page 8

Hardware Description and Connection

GS1100-16

GS1100-24

GS1100-8HP

GS1100-24E

GS1100-10HP

2.1 Rear Panel

The power receptacle is located on the rear panel of the Switch. Refer to the power supply requirements on the panel.

Figure 5 Rear Panel

CHAPTER 2

2.1.1 Rear Panel Power Connection

Connect one end of the supplied power cord or power adaptor to the power receptacle on the back of the Switch and the other end to the appropriate power source.

For the GS1100-8HP, GS1100-16, GS1100-24E and GS1100-10HP, use the POWER ON/OFF switch to have the Switch power on or off.

GS1100 Series User’s Guide

Page 9

Chapter 2 Hardware Description and Connection

2.2 Front Panel

The front panel of the Switch includes the auto-negotiating 10 Base-T /100 Base-TX/1000 Base-T RJ-45 ports and the LEDs.

The GS1100-24 and GS1100-10HP have two SFP slots. Refer to Section 2.2.3 on page 9 for more information.

2.2.1 RJ-45 Auto-negotiating Ports

The 10 Base-T/100 Base-TX/1000 Base-T RJ-45 ports are auto-negotiating and auto-crossover.

An auto-negotiating port can detect and adjust to the optimum Ethernet speed (10/100/1000 Mpbs) and duplex mode (full duplex or half duplex) of the connected device.

An auto-crossover (auto-MDI/MDI-X) port automatically works with a str aight -through or crossov er Ethernet cable.

2.2.2 IEEE 802.3az EEE

The Switch supports the IEEE 802.3az EEE (Energy Efficient Ethernet) standard to help reduce power consumption. This allows the Switch to go into power saving mode and switch off part of receive and transmit circuitry when it is not transmitting or receiving data through an Ethernet connection.

An EEE-enabled device initiates Low Power Idle (LPI) signals to negotiate and wake up the remote device when there is data to be transmitted. To use EEE, both devices should be EEE compliant.

EEE is configured on a per-system basis in the Switch. If one of the networking devices that connect to the Switch doesn't support EEE, EEE may not work in the Switch to save power.

Press in the IEEE 802.3az EEE ON/OFF button on the front panel to turn on the EEE feature. Disable it if you don't want the network performance to be impacted due to the latency from the additional time required for the sleep and wake transition or if the remote side doesn't support it.

2.2.3 SFP Slots (GS1100-24 and GS1100-10HP)

These are slots for Small Form-factor Pluggable (SFP) transceivers. A transceiver is a single unit that houses a transmitter and a receiver. The Switch does not come with transceivers. You must use transceivers that comply with the Small Form-factor Pluggable (SFP) Transceiver MultiSource Agreement (MSA). See the SFF committee’s INF-8074i specification Rev 1.0 for details.

You can change transceivers while the Switch is operating. You can use different transceivers to connect to Ethernet switches with different types of fiber-optic or even copper cable connectors.

To avoid possible eye injury, do not look into an operating fiber-optic module’s connectors.

• Type: SFP connection interface

• Connection speed: 100 Megabit per second (Mbps) or 1 Gigabit per second (Gbps)

GS1100 Series User’s Guide

Page 10

Chapter 2 Hardware Description and Connection

2.2.3.1 Transceiver Installation

Use the following steps to install a SFP module.

1 Insert the transceiver into the slot with the exposed section of PCB board facing down.

2 Press the transceiver firmly until it clicks into place.

3 The Switch automatically detects the installed transceiver. Check the LEDs to verify that it is

functioning properly.

4 Close the transceiver’s latch (latch styles vary).

5 Connect the fiber optic cables to the transceiver.

Figure 6 Transceiver Installation Example

Figure 7 Connecting the Fiber Optic Cables

2.2.3.2 Transceiver Removal

Use the following steps to remove a SFP module.

1 Remove the fiber optic cables from the transceiver.

2 Open the transceiver’s latch (latch styles vary).

3 Pull the transceiver out of the slot.

Figure 8 Removing the Fiber Optic Cables

GS1100 Series User’s Guide

Page 11

Chapter 2 Hardware Description and Connection

Figure 9 Opening the Transceiver’s Latch Example

Figure 10 Transceiver Removal Example

2.2.4 Front Panel Connections

You can use unshielded twisted pair (UTP) or shielded twisted-pair (STP) Ethernet cables for RJ-45 ports. The following table describes the types of network cable used for the different connection speeds. .

Table 2 Network Cable Types

SPEED NETWORK CABLE TYPE

10 Mbps Category 3, 4 or 5 UTP/STP 100 Mbps Category 5 UTP/STP 1000 Mbps Category 5e, 6 UTP/STP

You can use either crossover or straight-through cables for all the ports.

2.2.5 Front Panel LEDs

The LED Indicators give real-time information about the status of the Switch. The following table provides descriptions of the LEDs.

GS1100 Series User’s Guide

Page 12

Chapter 2 Hardware Description and Connection

GS1100-8HP

GS1100-16

GS1100-24

GS1100-24E

GS1100-10HP

Figure 11 Front Panel LEDs

The following table describes the LEDs.

Table 3 The Front Panel LED Descriptions: GS1100-8HP

LED COLOR STATUS DESCRIPTION

PWR Green On The Switch is on and receiving power.

Off The Switch is not receiving power.

PoE MAX Red On Power supplied to the PoE port(s) reachs the power budget limit or

exceeds the total PoE power budget on the Switch.

Off Power supplied to the PoE port(s) is below the power budget limit.

GS1100 Series User’s Guide

Page 13

Chapter 2 Hardware Description and Connection

Table 3 The Front Panel LED Descriptions: GS1100-8HP

LED COLOR STATUS DESCRIPTION

PoE Amber On Power is supplied to the PoE port.

Off Power is not supplied to the PoE port.

1G Green On The port is connected to an Ethernet network at 1000M speed.

Blinking The port is receiving or transmitting data at 1000M speed. Off The port is not connected to an Ethernet network.

10/100 Amber On The port is connected to an Ethernet network at 10M or 100M speed.

Blinking The port is receiving or transmitting data at 10M or 100M speed. Off The port is not connected to an Ethernet network.

Table 4 The Front Panel LED Descriptions: GS1100-16/24/24E

LED COLOR STATUS DESCRIPTION

PWR Green On The Switch is on and receiving power.

Off The Switch is not receiving power.

LINK/ ACT

Green On The p ort is connected to an Ethernet network.

Blinking The port is receivi ng or transmitting data. Off The port is not connected to an Ethernet network.

Table 5 The Front Panel LED Descriptions: GS1100-10HP

LED COLOR STATUS DESCRIPTION

PWR Green On The Switch is on and receiving power.

Off The Switch is not receiving power.

PoE MAX Amber On Power supplied to the PoE port(s) has reached ninety-five percent of the

power budget limit or has exceeded the total PoE power budget on the Switch.

Off Power supplied to the PoE port(s) is below the power budget limit. PoE 10/100/1000Base-T Ports Link/ACT

(Left)

PoE Mode (Right)

SFP Green On The port is connected to an Ethernet network at 1 Gbps.

Green On The p ort is connected to an Ethernet network at 1 Gbps.

Blinking The port is receiv ing or transmitting data at 1 Gbps.

Off The port is not connected to an Ethernet network.

Amber On The port is connected to an Ethernet network at 10/100 Mbps.

Blinking The port is receiving or transmitting data at 10/100 Mbps.

Off The port is not connected to an Ethernet network.

Green On Power supplied to the PoE port(s) complies with the IEEE 802.3at.

Off Power supplied to the PoE port(s) is not exported.

Amber On Power supplied to the PoE port(s) complies with the IEEE 802.3af.

Off Power supplied to the PoE port(s) is not exported.

Blinking The port is receiv ing or transmitting data at 1 Gbps.

Off The port is not connected to an Ethernet network.

Amber On The port is connected to an Ethernet network at 100 Mbps.

Blinking The port is receiv ing or transmitting data at 100 Mbps.

Off The port is not connected to an Ethernet network.

GS1100 Series User’s Guide

Page 14

Chapter 2 Hardware Description and Connection

2.3 Hardware Installation

See the following table for a comparison of the hardware installation methods of each GS1100 model:

Table 6 GS1100 Series Installation Comparison Table

MODEL FEATURE GS1100-8HP GS1100-16 GS1100-24 GS1100-24E GS1100-10HP

Desktop Device Wall-mountable Rack-mountable

Note: Ask an authorized technician to attach the Switch to the rack/wall.

For GS1100-8HP, GS1100-16, GS110-24E and GS1100-10HP, you can place the Switch directly on top of your desk or have it wall-mounted. For GS1100-16, GS1100-24 and GS110-24E, the size is suitable for rack-mounting and y ou can refer to Sect ion 2.3. 2 on p ag e 15 for instruction. Take note of the following:

• The Switch should have a minimum 25 mm space around it for ventilation.

• The Switch should be placed in a desk that has a level surface and that is able to support the weight of the Switch.

To start using it, simply connect the power cables and turn on the Switch.

2.3.1 Wall Mounting

Do the following to attach your Switch to a wall.

See Table 7 on page 14 for how far apart to place the screws.

Table 7 Distance between the centers of the holes for wall mounting

MODEL DISTANCE

GS1100-8HP 120 mm GS1100-16 148 mm GS1100-24E 207 mm GS1100-10HP 176mm

1 Screw the two screws provided with your Switch into the wall (see the figure in step 2). Use screws

with 6 mm ~ 8 mm (0.24" ~ 0.31") wide heads. Do not screw the screws all the way in to the wall; leave a small gap between the head of the screw and the wall.

The gap must be big enough for the screw heads to slide into the screw slots and the connection cables to run down the back of the Switch.

Note: Make sure the screws are securely fixed to the wall and strong enough to hold the

weight of the Switch with the connection cables.

2 Align the holes on the back of the Switch with the screws on the wall. Hang the Switch on the

screws.

GS1100 Series User’s Guide

Page 15

Chapter 2 Hardware Description and Connection

The Switch should be wall-mounted horizontally. The Switch's side panels with ventilation slots should not be facing up or down as this position is less safe.

2.3.2 Rack Mounting

The Switch can be mounted on an EIA standard size, 19-inch rack or in a wiring closet with other equipment. Follow the steps below to mount your Switch on a standard EIA rack using a rackmounting kit.

Rack-mounted Installation Requirements

• Two mounting brackets.

• Eight M3 flat head screws and a #2 Philips screwdriver.

• Four M5 flat head screws and a #2 Philips screwdriver.

Failure to use the proper screws may damage the unit.

Precautions

• Make sure the rack will safely support the combined weight of all the equipment it contains.

• Make sure the position of the Switch does not make the rack unstable or top-heavy. Take all necessary precautions to anchor the rack securely before installing the unit.

Attaching the Mounting Brackets to the Switch

1 Position a mounting bracket on one side of the Switch, lining up the four screw holes on the br acket

with the screw holes on the side of the Switch.

GS1100 Series User’s Guide

Page 16

Chapter 2 Hardware Description and Connection

Figure 12 Attaching the Mounting Brackets (GS1100-16 and GS1100-24E)

Figure 13 Attaching the Mounting Brackets (GS1100-24)

2 Using a #2 Philips screwdriver, install the M3 flat head screws through the mounting bracket holes

into the Switch.

3 Repeat steps 1 and 2 to install the second mounting bracket on the other side of the Switch.

4 You may now mount the Switch on a rack. Proceed to the next section.

2.3.3 Mounting the Switch on a Rack

1 Position a mounting bracket (that is already attached to the Switch) on one side of the rack, lining

up the two screw holes on the bracket with the screw holes on the side of the rack.

GS1100 Series User’s Guide

Page 17

Chapter 2 Hardware Description and Connection

Figure 14 Mounting the Switch on a Rack (GS1100-16 and GS1100-24E)

Figure 15 Mounting the Switch on a Rack (GS1100-24)

2 Using a #2 Philips screwdriver, install the M5 flat head screws through the mounting bracket holes

into the rack.

3 Repeat steps 1 and 2 to attach the second mounting bracket on the other side of the rack.

GS1100 Series User’s Guide

Page 18

CHAPTER 3

This section describes common problems you may encounter with the Switch and possible solutions.

Troubleshoot the Switch using the LEDs to detect problems.

The PWR LED on the front panel does not light up.

• Check the connections from your Switch to the power source. Make sure you are using the supplied power cord and that you are using an appropriate power source. Refer to the product specifications.

• Make sure the power source is turned on and that the Switch is receiving sufficient power.

• If these steps fail to correct the problem, contact your local distributor for assistance.

Troubleshooting

The LNK/ACT, 1G or 10/100 LED does not light up when a device is connected.

• Verify that the attached device(s) is turned on and properly connected to your Switch.

• Make sure the network adapters are working on the attached devices.

• Verify that proper network cable type is used and its length does not exceed 100 meters. For more information on network cable types, see Section 3.1 on page 19.

The PoE LED is off and/or power is not being supplied to my PoE-enabled device. (F or GS1100-8HP and GS1100-10HP)

• Check to see that the power adaptor is securely connected to the GS1100-8HP (or GS110010HP) and an appropriate power source. Make sure the power source is on and functioning properly.

• Check that the Ethernet cables are connected properly and that you are using the correct type of Ethernet cable. Contact your local distributor if the problem persists.

GS1100 Series User’s Guide

Page 19

Chapter 3 Troubleshooting

3.1 Improper Network Cabling and Topology

Improper network cabling or topology setup is a common cause of poor network performance or even network failure.

Figure 16 Troubleshooting Improper Network Cabling and Topology

PROBLEM CORRECTIVE ACTION

Faulty cables Using faulty network cables may affect data rates and have an impact on your network

Non-standard network cables

Cabling Length If you use longer cables than are needed, transmission quality may be affected.

Too many hubs between the computers in the network

A loop in the data path

performance. Replace with new standard network cables. Non-standard cables may increase the number of network collisions and cause other

network problems that affect your network performance. Refer to Sectio n 2.2.4 on page 11 for more information on network cable types.

The network cables should not be longer than the limit of 100 meters. Too many hubs (or repeaters) between the connected computers in the network may

increase the number of network collision or other network problems. Remove unnecessary hubs from the network.

A data path loop forms when there is more than one path or route between two networked computers. This results in broadcast storms that will severely affect your network performance. Make sure there are no loops in your network topology.

GS1100 Series User’s Guide

Page 20

any language, or transmitted in any form or by any means, electron ic, mecha nical, magneti c, optic al, chemic al, photoc opying, ma nual, or otherwise, without the prior written permission of ZyXEL Communications Corporation.

Disclaimer

ZyXEL does not assume any liability arising out of the application or use of any products, or software described herein. Neither does it convey any license under its patent rights nor the patent rights of others. ZyXEL further reserves the right to make changes in any products described herein without notice. This publication is subject to change without notice.

Regulatory Notice and Statement (Class A)

Model List: GS1100-8HP, GS1100-24

United States of America

APPENDIX A

Legal Information

Federal Communications Commission (FCC) EMC Statement

• This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference. (2) This device must accept any interference re ceived, including interference that may cause undesired operations.

• Changes or modifications not expressly app roved by th e party resp onsible for co mpliance co uld void th e user’s authority to op erate the equipment.

• This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not i nstalled and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Canada

The following information applies if you use the product within Canada area

Industry Canada ICES statement

CAN ICES-3 (A)/NMB-3(A)

European Union

The following information applies if you use the product within the European Union.

CE EMC statement

GS1100 Series User’s Guide

Page 21

Appendix A Legal Information

This is Class A Product. In dome stic envir onment this p roduct may c ause rad io interfer ence in which case the user may be requir ed to take adequate measures.

List of National Codes

COUNTRY ISO 3166 2 LETTER CODE COUNTRY ISO 3166 2 LETTER CODE

Austria AT Malta MT Belgium BE Netherlands NL Cyprus CY Poland PL Czech Republic CR Portugal PT Denmark DK Slovakia SK Estonia EE Slovenia SI Finland FI Spain ES France FR Sweden SE Germany DE United Kingdom GB Greece GR Iceland IS Hungary HU Liechtenstein LI Ireland IE Norway NO Italy IT Switzerland CH Latvia LV Bulgaria BG Lithuania LT Romania RO Luxembourg LU Turkey TR

Notices

CLASS 1 LASER PRODUCT APPAREIL À LASER DE CLASS 1 PRODUCT COMPLIES WITH 21 CFR 1040.10 AND 1040.11. PRODUIT CONFORME SELON 21 CFR 1040.10 ET 1040.11.

Safety Warnings

• Do NOT use this product near water, for example, in a wet basement or near a swimming pool.

• Do NOT expose your device to dampness, dust or corrosive liquids.

• Do NOT store things on the device.

• Do NOT install, use, or service this device during a thunderstorm. There is a remote risk of electric shock from lightning.

• Connect ONLY suitable accessories to the device.

• Do NOT open the device or unit. Opening or removing covers can expose you to dangerous high voltage points or other risks. ONLY qualified service personnel should service or disassemble this device. Please contact your vendor for further information.

• Make sure to connect the cables to the correct ports.

• Place connecting cables carefully so that no one will step on them or stumble over them.

• Always disconnect all cables from this device before servicing or disassembling.

• Use ONLY an appropriate power adaptor or cord for your device. Connect it to the right supply voltage (for example, 110V AC in North America or 230V AC in Europe).

• Do NOT remove t he plug a nd con nect it to a powe r outle t by its elf; always att ach the plug to the power adap tor first be fore connecting it to a power outlet.

• Do NOT allow anything to rest on the power adaptor or cord and do NOT place the product where anyone can walk on the power adaptor or cord.

• Do NOT use the device if the power adaptor or cord is damaged as it might cause electrocution.

• If the power adaptor or cord is damaged, remove it from the device and the power source.

• Do NOT attempt to repair the power adaptor or cord. Contact your local vendor to order a new one.

• Do not use the device outside, and make sure all the connections are indoors. There is a remote risk of electric shock from lightning.

• CAUTION: RISK OF EXPLOSION IF BATTERY (on the motherboard) IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. Dispose them at the applicable collection point for the recycling of electrical and electronic equipment. For detailed information about recycling of this product, please contact your local city office, your household waste disposal service or the store where you purchased the product.

• Do NOT obstruct the device ventilation slots, as insufficient airflow may harm your device.

• Antenna Warning! This device meets ETSI and FCC certification requirements when using the included antenna(s). Only use the included antenna(s).

• If you wall mount your wall-mountable device, make sure that no electrical lines, gas or water pipes will be damaged.

The following warnings apply if product is disconnect device:

• A readily accessible disconnect device shall be incorporated external to the equipment; and/or

The socket-outlet shall be installed near the equipment and shall be easily accessible.

WEEE Directive

GS1100 Series User’s Guide

Page 22

Appendix A Le gal Information

Your product is marked with this symbol, which is known as the WEEE mark. WEEE stands for Waste Electronics and Electrical Equipment. It means that used electrical and electronic products should not be mixed with general waste. Used electrical and electronic equipment should be treated separately.

Die folgende Symbol bedeutet, dass Ihr Produkt und/oder seine Batterie gemäß den örtlichen Bestimmungen getrennt vom Hausmüll entsorgt werden muss. Wenden Sie sich an eine Recyclingstation, wenn dieses Produkt das Ende seiner Lebensdauer erreicht hat. Zum Zeitpunkt der Entsorgung wird die getrennte Sammlung von Produkt und/oder seiner Batterie daz u beitragen, natürliche Ressourcen zu sparen und die Umwelt und die menschliche Gesundheit zu schützen.

El símbolo de abajo indica que según las regulaciones locales, su producto y/o su batería deberán depositarse como basura separada de la doméstica. Cuando este producto alcance el final de su vida útil, llévelo a un punto limpio. Cuando llegue el momento de desechar el producto, la recogida por separado éste y/o su batería ayudará a salvar los recursos naturales y a proteger la salud humana y medioambiental.

Le symbole ci-dessous signifie que selon les réglementations en vigueur votre produit et/ou sa batterie doivent être éliminés séparément des ordures ménagères. Lorsque ce produit atteint sa fin de vie, amenez-le à un centre de recyclage pour qu’il soit mis au rebut. La collecte séparée de votre produit et/ou de sa batterie permettra une meilleure protection de l'environnement et de la santé humaine.

Questo simbolo significa che secondo i regolamenti locali il prodotto e/o la sua batteria devono essere trattati separatamente dai rifiuti domestici. Quando questo prodotto raggiunge la fine della vita di servizio portatelo ad una stazione di riciclaggio. Questo trattamento separato del prodotto e/o della sua batteria aiuta a risparmiare risorse naturali e a proteggere l'ambiente.

Symbolen innebär att enligt lokal lagstiftning ska produkten och/eller dess batteri kastas separat från hushållsavfallet. När den här produkten når slutet av sin livslängd ska du ta den till en återvinningsstation. Separat insamling av din produkt och / eller dess batteri hjälper till att både spara naturresurser och se till att miljön når en hållbar utveckling.

GS1100 Series User’s Guide

Page 23

Environmental Product Declaration

Appendix A Legal Information

GS1100 Series User’s Guide

Page 24

Appendix A Le gal Information

台灣

以下訊息僅適用於產品銷售至台灣地區這是甲類的資訊產品，在居住的環境中使用時，可能會造成射頻干擾，在這種情況下，使用者會被要求採取某些適當的對策。

安全警告為了您的安全，請先閱讀以下警告及指示:

• 請勿將此產品接近水、火焰或放置在高溫的環境。

• 避免設備接觸

• 任何液體 - 切勿讓設備接觸水、雨水、高濕度、污水腐蝕性的液體或其他水份。

• 灰塵及污物 - 切勿接觸灰塵、污物、沙土、食物或其他不合適的材料。

• 切勿重摔或撞擊設備，並勿使用不正確的電源變壓器。若接上不正確的電源變壓器會有爆炸的風險。

• 請勿隨意更換產品內的電池。

• 如果更換不正確之電池型式，會有爆炸的風險，請依製造商說明書處理使用過之電池。

• 請將廢電池丟棄在適當的電器或電子設備回收處。

• 請勿將設備解體。

• 請勿阻礙設備的散熱孔，空氣對流不足將會造成設備損害。

• 請插在正確的電壓供給插座 ( 如:北美 / 台灣電壓 110V AC，歐洲是 230V AC)。

• 假若電源變壓器或電源變壓器的纜線損壞，請從插座拔除，若您還繼續插電使用，會有觸電死亡的風險。

• 請勿試圖修理電源變壓器或電源變壓器的纜線，若有毀損，請直接聯絡您購買的店家，購買一個新的電源變壓器。

• 請勿將此設備安裝於室外，此設備僅適合放置於室內。

• 請勿隨一般垃圾丟棄。

• 請參閱產品背貼上的設備額定功率。

• 請參考產品型錄或是彩盒上的作業溫度。

Regulatory Notice and Statement (Class B)

Model List: GS1100-10HP, GS1100-16, GS1100-24E

United States of America

Federal Communications Commission (FCC) EMC Statement

• This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference. (2) This device must accept any interference re ceived, including interference that may cause undesired operations.

• Changes or modifications not expressly app roved by th e party resp onsible for co mpliance co uld void th e user’s authority to op erate the equipment.

• This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

• If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment or devices

• Connect the equipment to an outlet other than the receiver’s

• Consult a dealer or an experienced radio/TV technician for assistance

Canada

The following information applies if you use the product within Canada area

Industry Canada ICES statement

CAN ICES-3 (B)/NMB-3(B)

List of National Codes

COUNTRY ISO 3166 2 LETTER CODE COUNTRY ISO 3166 2 LETTER CODE

Austria AT Malta MT Belgium BE Netherlands NL Cyprus CY Poland PL Czech Republic CR Portugal PT Denmark DK Slovakia SK

GS1100 Series User’s Guide

Page 25

COUNTRY ISO 3166 2 LETTER CODE COUNTRY ISO 3166 2 LETTER CODE

Estonia EE Slovenia SI Finland FI Spain ES France FR Sweden SE Germany DE United Kingdom GB Greece GR Iceland IS Hungary HU Liechtenstein LI Ireland IE Norway NO Italy IT Switzerland CH Latvia LV Bulgaria BG Lithuania LT Romania RO Luxembourg LU Turkey TR