Zebra LS3408-FZ Reference Guide

LS3408
Product Reference Guide
LS3408
Product Reference Guide
72E-67133-06
Revision B
March 2015
ii LS3408 Product Reference Guide
without permission in writing from Zebra. This includes electronic or mechanical means, such as photocopying, recording, or information storage and retrieval systems. The material in this ma nual is subject to change without notice.
The software is provided strictly on an “as i s” basis. All sof twar e, including firmware, furnished to the user is on a licensed basis. Zebra grants to the user a non-transferable and non-exclusive license to use each software or firmware program delivered hereunder (licensed program) . Except as n oted below, such license may not be assigned, sublicensed, or otherwise tran sfe rr e d by th e user without prior written consent of Zebra. No right to copy a licensed program in whole or in part is granted, exce pt as permitted unde r copyright law. The user shall not modify , merge, or incorporate any for m or portion of a licensed program with other pro gram material, create a derivative work from a licensed program , or us e a li censed program in a network without written permission from Zebra. The user agrees to maintain Zebra’s copyright notice on the licensed programs delivered hereunder , and to include the same on any authorized copies it makes, in whole or in part. The user agrees not to decompile, disassemble, decode, or reverse engineer any licensed program delivered to the user or any portion thereof.
Zebra reserves the right to make changes to any software or product to improve reliability, function, or design. Zebra does not assume any product liability arising out of, or in connection with, the application or use of any
product, circuit, or application described herein. No license is granted, either expressly or by implication, estoppel, or otherwise under any Zebra Technologies
Corporation, intellectual property rights. An implied license only exists for equipment, circuits, and subsystems contained in Zebra products.
Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of Symbol Technologies, Inc., a Zebra Technologies company. All other trademarks are the property of their respective owners.
Zebra Technologies Corporation Lincolnshire, IL U.S.A.
http://www.zebra.com

Warranty

For the complete Zebra hardware product warranty statement, go to:
http://www.zebra.com/warranty

Revision History

Changes to the original manual are listed below:
Change Date Description
-01 Rev A 2/2004 Initial release.
iii
-02 Rev A 10/2007 Rebranding; add new UPC/EAN Supplemen Supplementals option, and Bookland ISBN format.
-03 Rev A 10/2008 Add custom defaults option, add parameter scanning option, remove IBM XT bar co
de and keyboard from Keyboard Wedge section, add French Belgian country codes, change UCC/EAN-128 code type to GS1-128, add specific string search and new move cursor options in ADF chapter.
-04 Rev A 10/2012 Update URLs; remove patents; update ambient light tolerance.
-05 Rev A 12/2014 Zebra Rebran din g
-06 Rev A 1/2015 Added UCC Coupon Extended Code.
-06 Rev B 3/2015 Zebra Rebranding
tal options, User-Programmable
iv LS3408 Product Reference Guide
Table of Contents
Warranty........................................................................................................................ ii
Revision History............................................................................................................. iii
About This Guide
Introduction.................................................................................................................... xiii
Chapter Descriptions..................................................................................................... xiii
Service Information........................................................................................................ xv
Chapter 1: Getting Started
Introduction ................................................................................................................... 1-1
Unpacking the Scanner ................................................................................................ 1-2
Setting Up the Scanner ................................................................................................. 1-3
Installing the Interface Cable .................................................................................. 1-3
Connecting Power (if required) ............................................................................... 1-4
Connecting a Synapse Cable Interface .................................................................. 1-5
Removing the Interface Cable ................................................................................ 1-5
Configuring the Scanner ......................................................................................... 1-5
Chapter 2: Scanning
Introduction ................................................................................................................... 2-1
Beeper Definitions ........................................................................................................ 2-2
LED Definitions ............................................................................................................. 2-3
Scanning in Hand-Held Mode ....................................................................................... 2-3
Aiming ..................................................................................................................... 2-4
Scanning in Presentation Mode .................................................................................... 2-5
Decode Zone ................................................................................................................ 2-6
Chapter 3: Maintenance and Technical Specifications
Introduction ................................................................................................................... 3-1
Maintenance ................................................................................................................. 3-1
vi LS3408 Product Reference Guide
Troubleshooting ............................................................................................................ 3-2
Technical Specifications ............................................................................................... 3-4
Scanner Signal Descriptions ......................................................................................... 3-6
Chapter 4: User Preferences
Introduction ................................................................................................................... 4-1
Scanning Sequence Examples ..................................................................................... 4-1
Errors While Scanning .................................................................................................. 4-2
User Preferences Default Parameters .......................................................................... 4-2
User Preferences .......................................................................................................... 4-3
Set Default Parameter ............................................................................................ 4-3
Parameter Scanning ............................................................................................... 4-4
Beeper Tone ........................................................................................................... 4-4
Beeper Volume ....................................................................................................... 4-5
Power Mode ............................................................................................................ 4-5
Laser On Time ........................................................................................................ 4-6
Beep After Good Decode ........................................................................................ 4-6
Trigger Mode ........................................................................................................... 4-7
Aim Duration ........................................................................................................... 4-8
Chapter 5: Keyboard Wedge Interface
Introduction ................................................................................................................... 5-1
Connecting a Keyboard Wedge Interface ..................................................................... 5-2
Keyboard Wedge Default Parameters .......................................................................... 5-3
Keyboard Wedge Host Types ....................................................................................... 5-4
Keyboard Wedge Host Types ................................................................................. 5-4
Keyboard Wedge Country Types (Country Codes) ................................................ 5-5
Ignore Unknown Characters ................................................................................... 5-7
Keystroke Delay ...................................................................................................... 5-7
Intra-Keystroke Delay ............................................................................................. 5-8
Alternate Numeric Keypad Emulation ..................................................................... 5-8
Caps Lock On ......................................................................................................... 5-8
Caps Lock Override ................................................................................................ 5-9
Convert Wedge Data .............................................................................................. 5-9
Function Key Mapping ............................................................................................ 5-10
FN1 Substitution ..................................................................................................... 5-10
Send Make and Break ............................................................................................ 5-10
Keyboard Maps ....................................................................................................... 5-11
ASCII Character Set ..................................................................................................... 5-13
Chapter 6: RS-232 Interface
Introduction ................................................................................................................... 6-1
Connecting an RS-232 Interface .................................................................................. 6-2
RS-232 Default Parameters .......................................................................................... 6-3
RS-232 Host Parameters .............................................................................................. 6-4
RS-232 Host Types ................................................................................................. 6-6
Baud Rate ............................................................................................................... 6-7
Parity ....................................................................................................................... 6-8
Check Receive Errors ............................................................................................. 6-9
Stop Bit Select ........................................................................................................ 6-10
Data Bits ................................................................................................................. 6-10
Hardware Handshaking .......................................................................................... 6-11
Software Handshaking ............................................................................................ 6-13
Host Serial Response Time-out .............................................................................. 6-15
RTS Line State ........................................................................................................ 6-16
Beep on <BEL> ....................................................................................................... 6-16
Intercharacter Delay ................................................................................................ 6-17
Nixdorf Mode A/B and OPOS/JPOS Beep/LED Options ........................................ 6-18
Ignore Unknown Characters ................................................................................... 6-18
ASCII / Character Set ................................................................................................... 6-19
Chapter 7: USB Interface
Introduction ................................................................................................................... 7-1
Connecting a USB Interface ......................................................................................... 7-2
USB Default Parameters .............................................................................................. 7-3
USB Host Parameters .................................................................................................. 7-4
USB Device Type .................................................................................................... 7-4
USB Country Keyboard Types (Country Codes) .................................................... 7-5
USB Keystroke Delay ............................................................................................. 7-7
USB CAPS Lock Override ...................................................................................... 7-8
USB Ignore Unknown Characters ........................................................................... 7-8
Emulate Keypad ...................................................................................................... 7-9
USB Keyboard FN 1 Substitution ............................................................................ 7-9
Function Key Mapping ............................................................................................ 7-10
Simulated Caps Lock .............................................................................................. 7-10
Convert Case .......................................................................................................... 7-11
ASCII Character Set ..................................................................................................... 7-12
Table of Contents vii
Chapter 8: IBM 468X/469X Interface
Introduction ................................................................................................................... 8-1
Connecting to an IBM 468X/469X Host ........................................................................ 8-2
IBM Default Parameters ............................................................................................... 8-3
IBM 468X/469X Host Parameters ................................................................................. 8-4
Port Address ........................................................................................................... 8-4
Convert Unknown to Code 39 ................................................................................. 8-4
Chapter 9: Wand Emulation Interface
Introduction ................................................................................................................... 9-1
Connecting a Wand Emulation Interface ...................................................................... 9-2
Wand Emulation Default Parameters ........................................................................... 9-3
Wand Emulation Host Parameters ............................................................................... 9-4
Wand Emulation Host Types .................................................................................. 9-4
Leading Margin (Quiet Zone) .................................................................................. 9-5
Polarity .................................................................................................................... 9-5
viii LS3408 Product Reference Guide
Ignore Unknown Characters ................................................................................... 9-6
Convert All Bar Codes to Code 39 .......................................................................... 9-7
Convert Code 39 to Full ASCII ............................................................................... 9-8
Chapter 10: Scanner Emulation Interface
Introduction ................................................................................................................... 10-1
Connecting Using Scanner Emulation .......................................................................... 10-2
Scanner Emulation Default Parameters ....................................................................... 10-3
Scanner Emulation Host ............................................................................................... 10-4
Scanner Emulation Host Parameters ........................................................................... 10-4
Beep Style ............................................................................................................... 10-4
Parameter Pass-Through ........................................................................................ 10-5
Convert Newer Code Types .................................................................................... 10-6
Module Width .......................................................................................................... 10-6
Convert All Bar Codes to Code 39 .......................................................................... 10-7
Code 39 Full ASCII Conversion .............................................................................. 10-7
Transmission Timeout ............................................................................................. 10-8
Ignore Unknown Characters ................................................................................... 10-9
Leading Margin ....................................................................................................... 10-10
Check For Decode LED .......................................................................................... 10-11
Chapter 11: 123Scan
Introduction ................................................................................................................... 11-1
Communication with 123Scan ...................................................................................... 11-1
123Scan Parameter ...................................................................................................... 11-2
Chapter 12: Symbologies
Introduction ................................................................................................................... 12-1
Scanning Sequence Examples ..................................................................................... 12-1
Errors While Scanning .................................................................................................. 12-1
Symbology Default Parameters .................................................................................... 12-2
UPC/EAN ...................................................................................................................... 12-5
Enable/Disable UPC-A ............................................................................................ 12-5
Enable/Disable UPC-E ............................................................................................ 12-5
Enable/Disable UPC-E1 .......................................................................................... 12-6
Enable/Disable EAN-13 .......................................................................................... 12-6
Enable/Disable EAN-8 ............................................................................................ 12-7
Enable/Disable Bookland EAN ............................................................................... 12-7
Decode UPC/EAN/JAN Supplementals .................................................................. 12-8
User-Programmable Supplementals ....................................................................... 12-11
UPC/EAN/JAN Supplemental Redundancy ............................................................ 12-11
Transmit UPC-A/UPC-E/UPC-E1 Check Digit ........................................................ 12-12
UPC-A Preamble .................................................................................................... 12-13
UPC-E Preamble .................................................................................................... 12-14
UPC-E1 Preamble .................................................................................................. 12-15
Convert UPC-E to UPC-A ....................................................................................... 12-16
Convert UPC-E1 to UPC-A ..................................................................................... 12-16
Table of Contents ix
EAN-8/JAN-8 Extend .............................................................................................. 12-17
Bookland ISBN Format ........................................................................................... 12-17
Code 128 ...................................................................................................................... 12-18
Enable/Disable Code 128 ....................................................................................... 12-18
Enable/Disable GS1-128 (formerly UCC/EAN-128) ................................................ 12-18
Enable/Disable ISBT 128 ........................................................................................ 12-19
Code 39 ........................................................................................................................ 12-20
Enable/Disable Code 39 ......................................................................................... 12-20
Enable/Disable Trioptic Code 39 ............................................................................ 12-20
Convert Code 39 to Code 32 .................................................................................. 12-21
Code 32 Prefix ........................................................................................................ 12-21
Set Lengths for Code 39 ......................................................................................... 12-22
Code 39 Check Digit Verification ............................................................................ 12-23
Transmit Code 39 Check Digit ................................................................................ 12-23
Code 39 Full ASCII Conversion .............................................................................. 12-24
Code 93 ........................................................................................................................ 12-25
Enable/Disable Code 93 ......................................................................................... 12-25
Set Lengths for Code 93 ......................................................................................... 12-25
Code 11 ........................................................................................................................ 12-27
Code 11 .................................................................................................................. 12-27
Set Lengths for Code 11 ......................................................................................... 12-27
Code 11 Check Digit Verification ............................................................................ 12-29
Transmit Code 11 Check Digits .............................................................................. 12-30
Interleaved 2 of 5 (I 2 of 5) ............................................................................................ 12-31
Enable/Disable Interleaved 2 of 5 ........................................................................... 12-31
Set Lengths for Interleaved 2 of 5 ........................................................................... 12-31
I 2 of 5 Check Digit Verification ............................................................................... 12-33
Transmit I 2 of 5 Check Digit ................................................................................... 12-33
Convert I 2 of 5 to EAN-13 ...................................................................................... 12-34
Discrete 2 of 5 (D 2 of 5) ............................................................................................... 12-35
Enable/Disable Discrete 2 of 5 ................................................................................ 12-35
Set Lengths for Discrete 2 of 5 ............................................................................... 12-35
Codabar (NW - 7) ......................................................................................................... 12-37
Enable/Disable Codabar ......................................................................................... 12-37
Set Lengths for Codabar ......................................................................................... 12-37
CLSI Editing ............................................................................................................ 12-39
NOTIS Editing ......................................................................................................... 12-39
MSI ............................................................................................................................... 12-40
Enable/Disable MSI ................................................................................................ 12-40
Set Lengths for MSI ................................................................................................ 12-40
MSI Check Digits .................................................................................................... 12-42
Transmit MSI Check Digit(s) ................................................................................... 12-42
MSI Check Digit Algorithm ...................................................................................... 12-43
GS1 DataBar (formerly Reduced Space Symbology) ................................................... 12-44
GS1 DataBar ........................................................................................................... 12-44
GS1 DataBar Limited .............................................................................................. 12-44
Convert GS1 DataBar to UPC/EAN ........................................................................ 12-45
Redundancy Level ........................................................................................................ 12-46
Redundancy Level 1 ............................................................................................... 12-46
Redundancy Level 2 ............................................................................................... 12-46
x LS3408 Product Reference Guide
Redundancy Level 3 ............................................................................................... 12-47
Redundancy Level 4 ............................................................................................... 12-47
Security Level ............................................................................................................... 12-48
Security Level 0 ...................................................................................................... 12-48
Security Level 1 ...................................................................................................... 12-48
Security Level 2 ...................................................................................................... 12-49
Security Level 3 ...................................................................................................... 12-49
Bi-directional Redundancy ............................................................................................ 12-49
Chapter 13: Miscellaneous Scanner Options
Introduction ................................................................................................................... 13-1
Scanning Sequence Examples ..................................................................................... 13-1
Errors While Scanning .................................................................................................. 13-1
Miscellaneous Default Parameters ............................................................................... 13-2
Miscellaneous Scanner Parameters ............................................................................. 13-3
Transmit Code ID Character ................................................................................... 13-3
Scan Angle .............................................................................................................. 13-4
Prefix/Suffix Values ................................................................................................. 13-4
Scan Data Transmission Format ............................................................................ 13-5
FN1 Substitution Values ......................................................................................... 13-7
Transmit “No Read” Message ................................................................................. 13-7
Synapse Interface ................................................................................................... 13-8
Chapter 14: Advanced Data Formatting
Introduction ................................................................................................................... 14-1
Rules: Criteria Linked to Actions ................................................................................... 14-1
Using ADF Bar Codes .................................................................................................. 14-2
ADF Bar Code Menu Example ..................................................................................... 14-2
Rule 1: The Code 128 Scanning Rule .................................................................... 14-3
Rule 2: The UPC Scanning Rule ............................................................................ 14-3
Alternate Rule Sets ................................................................................................. 14-3
Rules Hierarchy (in Bar Codes) .............................................................................. 14-5
Default Rules .......................................................................................................... 14-5
Special Commands ....................................................................................................... 14-6
Pause Duration ....................................................................................................... 14-6
Begin New Rule ...................................................................................................... 14-6
Save Rule ............................................................................................................... 14-6
Erase ....................................................................................................................... 14-7
Quit Entering Rules ................................................................................................. 14-7
Disable Rule Set ..................................................................................................... 14-8
Criteria .......................................................................................................................... 14-9
Code Types ............................................................................................................. 14-9
Code Lengths .......................................................................................................... 14-13
Message Containing A Specific Data String ........................................................... 14-18
Actions .......................................................................................................................... 14-23
Send Data ............................................................................................................... 14-23
Setup Field(s) .......................................................................................................... 14-27
Modify Data ............................................................................................................. 14-34
Pad Data with Spaces ............................................................................................. 14-35
Pad Data with Zeros ............................................................................................... 14-40
Beeps ...................................................................................................................... 14-45
Send Keystroke (Control Characters and Keyboard Characters) ........................... 14-46
Send Right Control Key .......................................................................................... 14-86
Send Graphic User Interface (GUI) Characters ...................................................... 14-87
Turn On/Off Rule Sets ............................................................................................ 14-93
Alphanumeric Keyboard ............................................................................................... 14-95
Appendix A: Standard Default Parameters
Appendix B: Programming Reference
Symbol Code Identifiers ................................................................................................ B-1
AIM Code Identifiers ..................................................................................................... B-2
Appendix C: Sample Bar Codes
UPC-A ........................................................................................................................... C-1
UPC-E ........................................................................................................................... C-1
UPC-E1 ......................................................................................................................... C-1
EAN-13 ......................................................................................................................... C-2
EAN-8 ........................................................................................................................... C-2
Code 39 ........................................................................................................................ C-2
Trioptic Code 39 ........................................................................................................... C-3
Code 93 ........................................................................................................................ C-3
Code 11 ........................................................................................................................ C-3
Codabar ........................................................................................................................ C-4
MSI ............................................................................................................................... C-4
Interleaved 2 of 5 .......................................................................................................... C-4
Table of Contents xi
Appendix D: Numeric Bar Codes
0, 1, 2 ............................................................................................................................ D-1
3, 4, 5, 6 ........................................................................................................................ D-2
7, 8, 9 ............................................................................................................................ D-3
Cancel ........................................................................................................................... D-3
Glossary
Index
Tell Us What You Think... 5
xii LS3408 Product Reference Guide

About This Guide

Introduction

The LS3408 Product Reference Guide provides general instructions for setting up, operating, maintaining, and
troubleshooting the scanner. The LS3408 includes the following variations of the scanner:
LS3408-FZ20005: 1-D scanni ng
LS3408-ER20005: extended range 1-D scanning.

Chapter Descriptions

Chapter 1, Getting Started provides a product overview and unpacking instructions.
Chapter 2, Scanning describes part s of the scanne r , b eeper and LED definitions, and h ow to use the scanner
in hand-held and hands-free modes.
Chapter 3, Maintenance and Technical Specifications provides information on how to care for the scanner,
troubleshooting, and technical specifications.
Chapter 4, User Preferences provides programming bar codes for selecting user preference features for the
scanner.
Chapter 5, Keyboard Wedge Interface provides information for setting up the sc an ne r fo r Keyb o ar d Wedge
operation.
Chapter 6, RS-232 Interface provides information for setting up the scanner for RS-232 operation.
Chapter 7, USB Interface provides information for setting up the scanner for USB operation.
Chapter 8, IBM 468X/469X Interface provides information for setting up the scanner with IBM 468X/469X
POS systems.
Chapter 9, Wand Emulation Interface pr ovides information for setting up the scanner fo r Wand Emulation
operation.
Chapter 10, Scanner Emulation Interface provides information for setting up the scanner for Scanner
Emulation operation.
xiv LS3408 Product Reference Guide
*Baud Rate 9600
Feature/Option
* Indicates Default
Chapter 11, 123Scan (PC based scanner configuration tool) provides the bar code to scan to communicate
with the 123Scan program.
Chapter 12, Symbologies describes all symbology features and provides programming bar codes for
selecting these features for the scanner.
Chapter 13, Miscellaneous Scanner Option s includes frequently used features to customize how data
transmits to the host device.
Chapter 14, Advanced Data Formatting (ADF) describes how to customize scanned data befo re transmitting
to the host.
Appendix A, Standard Defaul t Parameters provides a table of all host devices and miscellaneous scanner
defaults.
Appendix B, Programming Reference provides a table of AIM code identifiers, ASCII character conversions,
and keyboard maps.
Appendix C, Sample Bar Codes includes sample bar codes of various code types.
Appendix D, Numeric Bar Codes includes the numeric bar codes to scan for parameters requiring specific
numeric values.
Notational Conventions
The following conventions are used in this document:
Italics are used to highlight chapters and sections in this and related documents
Bullets (•) indicate:
tion items
ac
list
s of alternatives
list
s of required steps that are not necessarily sequential.
Sequential lists (e.g., those that describe step-by-s te p pr oc ed ur e s) ap pe a r as nu m be re d lists.
Throughout the programming bar code menus, asterisks (*) are used to denote default parameter settings.
Related Publications
The LS/DS3408 Quick Start Guide (p/n 72-67131-xx) provides general information to help you get started with the
scanner. It includes basic setup and operation instructions.
For the latest versions of the L
http://www.zebra.com/support.
S/DS3408 Quick Start Guide and the LS3408 Product Re ference Guide go to:

Service Information

If you have a problem using the equipment, contact your facility's technical or systems support. If there is a
problem with the equipment, they will contact the Zebra Global Customer Support Center at:
http://www.zebra.com/support.
When contacting Zebra support, please have the following information available:
Serial number of the unit
Model number or product name
Software type and version number
Zebra responds to calls by e-mail, telephone or fax within the time limits set forth in service agreements. If your
problem cannot be solved by Zebra support, you may need to return your equipment for servicing and will be given
specific directions. Zebra is not responsible for any damages incurred during shipment if the approved shipping
container is not used. Shipping the units improperly can possibly void the warranty.
If you purchased your business product from a Zebra business partner, please contact that business partner for
support.
About This Guide xv
xvi LS3408 Product Reference Guide
Chapter 1 Getting Started

Introduction

The scanner combines excellent scanning performance and advanced ergonomics to provide the best value in a
lightweight laser scanner . Whether using it as a ha nd-held scanner or in pr esentation (hands-fr ee) mode in a stand,
the scanner ensures comfort and ease of use for extended periods of time.
Figure 1-1
LS3408 Scanner
1 - 2 LS3408 Product Reference Guide
This scanner supports:
Standard RS-232 connection to a host.
Keyboard Wedge connection to a host, which interpret s scanned da t a as keystr okes. This interface supp ort s the following international keyboards (for the Windows
French Canadian, Spanish, Italian, Swedish, UK English, Japanese, and Brazilian-Portuguese.
Wand Emulation connection to a mobile computer, a controller, or host which collects the data as wand data and decodes it.
Scanner Emulation connection to a mobile computer or a controller which collects the data and interprets it for the host.
Connection to IBM® 468X/469X hosts.
USB connection to a host. The scanner autodetects a USB host and defaults to the HID keyboard interface type. Scan programming bar codes to select other USB inte rface types. Th is inter f ace suppo rts the following
international keyboards (for the Windows Canadian, Spanish, Italian, Swedish, UK English, Japanese, and Brazilian-Portuguese.
Synapse capability which enables connection to a wide variety of host systems using a Synapse and Synapse adapter cable. The scanner autodetects Synapse.
TM
environment): North America, German, French,
environment): North America, German, French, French
Configuration via 123Scan.

Unpacking the Scanner

Remove the scanner from its packing and inspect it for damage. If the scanner was damaged in transit, contact
Zebra Global Customer Support Center at:
shipping container and should be used if the equipment ever needs to be returned for servicing.
http://www.zebra.com/support. KEEP THE PACKING. It is the approved

Setting Up the Scanner

Installing the Interface Cable

1. Loosen the two screws on the cable clamp at the bottom of the scanner and gently pull the clamp away from
the bottom of the scanner.
Getting Started 1 - 3
Figure 1-2
2. Open the clamp and plug the interface cable modular connector into the cable interface port on the bottom of
the scanner handle.
Figure 1-3
3. Gently tug the cable to ensure the connector is properly secured.
Removing the Cable Clamp
Inserting the Interface Cable
1 - 4 LS3408 Product Reference Guide
4. Close the clamp, push it back into place and tighten the screws on the clamp to secure the cable into the
bottom of the scanner.
Figure 1-4
5. Connect the other end of the interface cable to the host (see the specific host chapter for information on host
Closing the Cable Clamp
connections).
NOTE Different hosts require different cables. The connectors illustrated in each host chapter are examples only.
The connectors may be different than those illustrated, but the steps to connect the scanner are the same.

Connecting Power (if required)

If the host does not provide power to the scanner, connect external power to power the scanner:
1. Connect the interface cable to the bottom of the scanner, as described in Installing the Interface Cable on page
1-3.
2. Connect the other end of the interface cable to the host (refer to the host manual to locate the correct port).
3. Plug the power supply into the power jack on the interface cable. Plug the other end of the power supp ly into
an AC outlet.
Getting Started 1 - 5
Synapse adapter cable
To scanner
Synapse Smart Cable
To host

Connecting a Synapse Cable Interface

NOTE Refer to the Synapse Interface Guide provided with the Synapse cable for detailed setup instructions.
Synapse Smart Cables enable interfacing to a variety of hosts. The appropriate Synapse cable has the built-in
intelligence to detect that host.
Figure 1-5
1. Plug the Synapse adapter cable into the bottom of the scanner, as described in Installing the Interface Cable
Synapse Cable Connection
on page 1-3.
2. Align the ‘S’ on the Synapse adapter cable with the ‘S’ on the Synapse Smart Cable and plug the cable in.
3. Connect the other end of the Synapse Smart Cable to the host.

Removing the Interface Cable

1. Loosen the two screws on the cable clamp at the bottom of the scanner and gently pull the clamp away from
the bottom of the scanner.
2. Open the clamp and unplug the interface cable modular connector from the cable interface port on the bottom
of the scanner handle. Carefully slide out the cable.
3. Follow the steps for Installing the Interface Cable on page 1-3 to connect a new cable.

Configuring the Scanner

Use the bar codes in this manual or the 123Scan configuration program to configure the scanner. See Chapter 4,
User Preferences and each host chapter for information about programming the scanner using bar code menus.
See Chapter 11, 123Scan to configure the scanner using this config
includes a help file.
uration program. The 123Scan program
1 - 6 LS3408 Product Reference Guide
Chapter 2 Scanning
Scan Trigger
Scan Window
LED
Indicators
Tether Plate

Introduction

This chapter provides beeper and LED definitions, techniqu es involved in scanning bar codes, general instructions
and tips about scanning, and decode zone diagrams.
Figure 2-1
Parts
2 - 2 LS3408 Product Reference Guide

Beeper Definitions

The scanner emits different beeper sequences and patterns to indicate its status. Table 2-1 defines beep
sequences that occur during both normal scanning and while programming the scanner.
Table 2-1
Standard Use
Short low/short medium/short high beep sequence
1 short high beep A bar code symbol was decoded (if decode beeper is enabled). 4 long low beeps A transmission error was detected in a scanned symbol. The data is
5 long low beeps Conversion or format error. Short high/short high/short high/long low
beep
Parameter Menu Scanning
Long low/long high beep sequence Incorrect programming sequence or
Short high/short low beep sequence Keyboard parameter selected. Enter value using bar code keypad. Short high/short low/short high/short low
beep
Standard Beeper Definitions
Beeper Sequence Indication
Power up.
nored.
ig
RS-232 receive error.
sequence
Scanner remains in program mode.
Successful program exit with change in the parameter setting.
sequence
Cancel
bar code scanned.
Short low/short high/short low/short high
sequence
beep
USB only
4 short high beeps Scanner did not complete initialization. Wai t several seconds and scan
Short low/short medium/short high beep
uence after scanning a USB Device
seq Type.
Short low/short medium/short high beep
uence occurs more than once.
seq
RS-232 only
1 short high beep A <BEL> character is received and Beep on <BEL> is enabled.
Out of host parameter storage spa ce. Scan
page 4-3
again. Communication with the bus must be established before the scanner
can operate at the highest power level.
The USB bus may put the scanner in a state where power to the scanner is cycled on and off more than once. This is normal and usually happens when the PC cold boots.
.
Set Default Parameter on

LED Definitions

RIGHT
012345
WRONG
012345
In addition to beeper sequences, the scanner uses the two-color LED to indicate its status. Table 2-2 defines LED
colors that display during
Scanning 2 - 3
scanning.
Table 2-2
Off The scanner is on and ready to scan, or no power is applied to the scanner. Green A bar code was successfully decoded. Red A data transmission error occurred.
Standard LED Definitions
LED Indication

Scanning in Hand-Held Mode

Install and program the scanner (see Setting Up the Scanner on page 1-3). For assistance, contact the local
supplier or Zebra Global Customer Support Center at: http://www.zebra
1. Connect the scanner to the host (see the appropriate host chapter).
2. Aim the scanner at the bar code.
3. Press the scan trigger.
.com/support.
Figure 2-2
4. Ensure the scan line crosses every bar and space of the symbol.
5. Upon successful decode, the scanner beeps, and the LED turns green. For more information on beeper and
LED definitions, see Table 2-1 and Table 2-2.
Scanning in Hand-Held Mode
2 - 4 LS3408 Product Reference Guide
65°
65°

Aiming

Do not hold the scanner directly over the bar code. Laser light reflecting directly back into the scanner from the bar
code is known as specular reflection. This specular reflection can make decoding difficult.
Tilt the scanner up to 65° forward or b
shows what tolerances to work within.
ack to achieve a successful decode (Figure 2-3). Simple practice quickly
Figure 2-3
Optimum Scan Angles

Scanning in Presentation Mode

Scanner “Cup”
Adjust height of IntelliStand
Adjust angle of scanner “cup”
The optional IntelliSta nd adds greater flexibility to scanning operation. When you insert the scanner into the stand’ s
“cup,” the scanner’s built-in sensor places the scanner in presentation (hands-free) mode. When you remove the
scanner from the stand, it operates in its normal hand-held mode.
Scanning 2 - 5
Figure 2-4
Inserting the Scanner in the IntelliStand
To operate the scanner in the IntelliStand:
1. Connect the scanner to the host (see the appropriate host chapter for information on host connections).
2. Insert the scanner into the IntelliStand by placing the front of the scanner into the stand’s “cup” (see Figure
2-4).
3. To scan a bar code, present the bar code and ensure the scan line crosses e very bar and spa ce of the symbol.
4. Upon successful decode, the scanner beeps and the LED turns green. For more information on beeper and
LED definitions, see Table 2-1 and Table 2-2.
2 - 6 LS3408 Product Reference Guide
2.5"
7.25"
5 mil
2.0" 15.75"
7.5 mil
1.0" 24"
13 mil
100% UPC
0"*
39.5"
26.5"
20 mil (80%MRD) 20 mil (31%MRD)
40 mil
55 mil
2.0"*
4.0"*
67.0"
84.0"
0 1020304050607080 0 25.4 50.8 76.2 101.6 127.0 152.4 177.8 203.2
90
228.6
30
20
10
00
10
20
30
76.2
50.8
25.4
25.4
50.8
76.2
LS 3408 FZ
Note: Typical performance at 68˚F (20˚C) on high quality Code 39 and UPC symbols.
*Minimum distance determined by symbol length and scan angle
Depth of Field
W
i d t h
o f
F
i e
l d
in. cm
in. cm

Decode Zone

Figure 2-5
LS3408-FZ Decode Zone
15" 180"
55 mil
365"
70 mil reflective
*
540"
100 mil reflective
0 60 120 180 240 300 360 420 480 540 600 0 152.4 304.8 457.2 609.6 762.0 914.4 1066.8 1219.2 1371.6 1524.0
0
24
48
72
72
48
24
0
61.0
121.9
182.9
182.9
121.9
61.0
LS 3408 ER
Depth of Field
in. cm
W
i d t h
o f
F
i e
l d
in. cm
Note: Typical performance at 73.4˚F (23˚C) on high quality Code 39 symbols.
*Near range determined by degree of reflectivity and width of bar code.
0.25" 20"
7.5 mil
2" 32"
10 mil
3" 69"
15 mil
3" 94"
20 mil
0 1020304050607080 90 100 0 25.4 50.8 76.2 101.6 127.0 152.4 177.8 203.2 228.6 254.0
0
4
8
12
12
8
4
0
10.2
20.3
30.5
30.5
20.3
10.2
LS 3408 ER
Depth of Field
in. cm
W
i
d
t
h
o
f
F
i
e
l
d
in. cm
Note: Typical performance at 73.4˚F (23˚C) on high quality Code 39 symbols.
Scanning 2 - 7
Figure 2-6
LS3408-ER Decode Zone
2 - 8 LS3408 Product Reference Guide
Chapter 3 Maintenance and Technical Specifications

Introduction

This chapter provides suggested scanner maintenance, troubleshooting, technical specifications, and signal descriptions (pinouts).

Maintenance

Cleaning the scan window is the only maintenance required. A dirty window can affect scanning accuracy.
Do not allow any abrasive material to touch the window.
Remove any dirt particles with a damp cloth.
Wipe the window using a tissue moistened with ammonia/water.
Do not spray water or other cleaning liquids directly onto the window.
3 - 2 LS3408 Product Reference Guide

Troubleshooting

Table 3-1
Scanner emits short low/short medium/short high beep sequence.
Nothing happens when scan trigger is pressed.
Troubleshooting
Problem Possible Causes Possible Solutions
Scanner is powering up. Normal when scanner is plugged in.
No power to the scanner. Check the system power . Ens ure the power
supply is connected if the configuration requires a power supply.
Power supply is not plugged in.
Incorrect host interface cable is used.
Interface/power cables are loose.
Scanner is disabled. For Simple Serial Interface (SSI), Synapse,
If using RS-232 Nixdorf B mode, CTS is not asserted.
Ensure that correct host interface cable is used.
Ensure all cable connections are secure.
or IBM 468x mode, enable the scanner via the host interface. Otherwise, see the technical person in charge of scanning.
Assert CTS line.
Scanner emits short low/short medium/short high beep sequence more than once.
Laser comes on, but scanner does not decode the bar code.
Scanner emits 4 short high beep s while attempting to scan.
The USB bus may put the scanner in a state where power to the scanner is cycled on and off more than once.
Scanner is not programmed for the correct bar code type.
Bar code symbol is unreadable. Check the symbol to ensure it is not
Bar code is out of range from the scanner.
Scanner has not completed USB initialization.
Normal during host reset.
Ensure the scanner is programmed to read the type of bar code being scanned.
defaced. Try scanning test bar codes of the same bar code type. See
Sample Bar Codes
Move scanner closer to or further from bar code.
Wait several seconds and scan again.
Appendix C,
for test bar codes.
Maintenance and Technical Specifications 3 - 3
Table 3-1
Bar code is decoded, but data is not transmitted to the host.
Scanned data is incorrectly displayed on the host.
Troubleshooting (Continued)
Problem Possible Causes Possible Solutions
Scanner is not programmed for the correct host type.
Interface cable is loose. Ensure all cable connections are secure. If 4 long low beeps are heard, a
transmission error was detected.
If 5 long low beeps are heard, a conversion or format error was detected.
Scanner is not programmed to work with the host.
Scan the appropriate host parameter bar codes.
Ensure the scanner's communication parameters match the host's setting.
Ensure the scanner's conversion parameters are properly configured.
Ensure proper host is selected. For RS-232, ensure the scanner's
communication parameters match the host's settings.
For a Keyboard Wedge configuration, ensure the system is programmed for the correct keyboard type, and the CAPS LOCK key is off.
Scanner emits short high/short high/short high/long low beep sequence when it is not in use.
Scanner emits long low/long high beep sequence while it is being programming.
Scanner emits short low/short high/short low/short high beep sequence while it is being programming.
Scanner emits a short low/short medium/short high beep sequence after changing USB host type.
Scanner emits 1 short high beep when it is not in use.
Ensure editing options (e.g., UPC-E to UPC-A conversion) are properly programmed.
RS-232 receive error. Normal during host reset. Otherwise, ensure
the scanner's RS-232 parity setting matches the host setting.
Input error or scanned.
Out of ADF parameter storage space.
Out of Synapse parameter storage space.
The USB bus re-establishes power to the scanner.
In RS-232 mode, a <BEL> character is received and Beep on <BEL> option is enabled.
Cancel
bar code
Ensure the correct numeric bar codes, that are within range for the parameter that is being programmed, are being scanned.
Erase all rules and re-program with shorter rules.
Scan
Set Synapse Defaults
the appropriate Synapse Interface Guide for cables no longer in use and re-program the scanner for the current host interface.
Normal when the USB host type is changed.
Normal when Beep on <BEL> is enabled and the scanner is in RS-232 mode.
bar code from
3 - 4 LS3408 Product Reference Guide
NOTE If after performing these checks the symbol still does not decode, contact the distributor or the Zebra
Global Customer Support Center at: http://www.zebra.com/support.

Technical Specifications

Table 3-2
Power Requirements 4.5 - 14VDC Stand-By Current 50mA (max) Power Source Depending on host:
Decode Capability UPC/EAN, Bookland EA N, UPC/EAN wit h supplement als , Code 128, GS1-12 8, ISBT
Beeper Operation User-selectable: Enable, Disable Beeper Volume User-selectable: Three levels Beeper Tone User-selectable: Three tones Scan Repetition Rate 36 scans/second Yaw Tolerance ± 50° from nominal ± 60° from nominal
Technical Specifications
Item
128, Code 39, Trioptic Code 39, Code 93, Code 11, Interleaved 2 of 5, Discrete 2 of 5, Codabar (NW-7), MSI, GS1 DataBar.
Description
LS3408-FZ LS3408-ER
host powered external power supply
Pitch Tolerance ± 65° from nominal ± 65° from nominal Roll Tolerance ± 20° from nominal ± 10° from nominal Print Contrast Minimum 25% minimum reflectance differential, measured at 650 nm. Ambient Light Tolerance Tolerant to typical artificial indoor and natural outdoor (direct sunlight) lighting
onditions. Fluorescent, Incandescent, Mercury Vapor, Sodium Vapor, LED: 450 Ft
c Candles (4,844 Lux) Sunlight: 8000 Ft Candles (86,111 Lux)
Note: LED lighting with high AC ripple content can impact scanning performance. Durability 6.5 ft (2.0 m) drops to concrete Operating Temperature -22° to 122° F (-30° to 50° C) Storage Temperature -40° to 158° F (-40° to 70° C) Humidity 5% to 95% (non-condensing) Weight (without cable) 12.35 oz. (350 g) 12.56 oz. (356 g)
Maintenance and Technical Specifications 3 - 5
Table 3-2
Dimensions: Height Width Depth
Laser 650nm laser diode Laser Classifications IEC 825-1 Class 2 ESD 20 kV area discharge
Minimum Element Width 5 mil (0.127 mm) 7.5 mi l (0.191 mm) Interfaces Supported Keyboard Wedge, RS-232, USB, IBM 468X/469X, Wand Emulation, Scanner
Electrical Safety Certified Pending to UL1950, CSA C22.2 No.950. EN60950/IC950 Input Transient Protection IEC 1000-4-(2,3,4,5,6,11) EMI FCC Part 15 Class B, ICES-003 Class B European Union EMC Directive, Australian
Technical Specifications (Continued)
Description
Item
LS3408-FZ LS3408-ER
7.34 in. (18.65 cm)
4.82 in. (12.25 cm)
2.93 in. (7.43 cm)
8 kV contact discharge
Emulation, Synapse
SMA, Taiwan EMC, Japan VCCI/MITI/Dentori
3 - 6 LS3408 Product Reference Guide
Cable interface port
Interface cable
modular connector
Bottom of scanner
PIN 1PIN 10

Scanner Signal Descriptions

Figure 3-1
Scanner Cable Pinouts
Maintenance and Technical Specifications 3 - 7
The signal descriptions in Table 3-3 apply to the connector on the scanner and are for reference only.
Table 3-3
Pin IBM Synapse RS-232
1 Reserved SynClock Reserved Reserved Reserved Jump to Pin 6 DBP 2 Power Power Power Power Power Power Power 3 Ground Ground Ground Ground Ground Ground Ground 4 IBM_A(+) Reserved TxD KeyClock DBP Reserved SOS 5 Reserved Reserved RxD TermData CTS D + Decode 6 IBM_B(-) SynData RTS KeyData RTS Jump to Pin 1 Trigger 7 Reserved Reserved CTS TermClock Reserved D - Enable 8 Reserved Reserved Reserved Reserved Reserved Reserved Reserved 9 Reserved Reserved Reserved Reserved Reserved Reserved Reserved 10 Reserved Reserved Reserved Reserved Reserved Reserved Reserved
Scanner Signal Pin-outs
Keyboard
Wedge
Wand USB
Scanner
Emulation
3 - 8 LS3408 Product Reference Guide
Chapter 4 User Preferences
*High Frequency
Feature/Option
* Indicates Default

Introduction

You can program the scanner to perform various functions, or activate different features. This chapter describes each user preference feature and provides programming bar codes for selecting these features for the scanner.
The scanner ships with the settings shown in the User Preferences Default Table on page 4-2 (also see Appendix
A, Standard Default Parameters for all host device and miscellaneous scanner defaults). If the default values suit
the requirements, programming is not necessary. Set feature values by scanning single bar codes or short ba
non-volatile memory and are preserved even when you power down the scanner. If not using a Synapse or USB cable, after hearing the power-up
for specific host information). You only need to do this once, upon the first power-up when connecting to a new host.
To return all features to their default values, see the Set Default Parameter on page 4-3. Throughout the programming bar code menus
, asterisks (*) indicate default values.

Scanning Sequence Examples

In most cases, you must only scan one bar code to set a parameter value. For exampl e, to set the beeper tone to high, scan the High Frequency (beeper tone) bar code under Beeper Tone on page 4-4. The scanner issues a fast warble beep and the LED turns green, signifying a suc c essful parameter entry.
Other parameters, such as specifying Laser On T several bar codes. See Laser On Time on page 4-6 and Scan Data Transmission Format on page 13-5 for descriptions of this procedure.
r code sequences. The settings are stored in
beeps, select a host type (see each host chapter
ime or setting Data Transmission Formats, require scanning
4 - 2 LS3408 Product Reference Guide

Errors While Scanning

Unless otherwise specified, to correct an error during a scanning sequence, just re-scan the correct parameter.

User Preferences Default Parameters

Table 4-1 lists the defaults for user prefe rences parameters. To change any option, scan the appropriate bar
code(s) provided in the User Preferences section beginning on page 4-3.
NOTE See Appendix A, Standard Default Parameters for all user preferences, hosts, symbologies, and
miscellaneous default parameters.
Table 4-1
User Preferences
Set Default Parameter Restore Defaults Parameter Scanning Enable Beeper Tone High Beeper Volume High Power Mode Continuous On Laser On Time 3.0 sec Beep After Good Decode Enable Trigger Mode Level Aim Duration 0.0 sec
User Preferences Default Table
Parameter Default
Page
Number
4-3 4-4 4-4 4-5 4-5 4-6 4-6 4-7 4-8

User Preferences

Set Default Parameter

You can reset the LS3408 to two types of defaults: factory defaults or custom defaults. Scan the appropriate bar code below to reset the scanner to its default settings and/or set its current settings as custom defaults.
Restore Defaults - Scan this bar code to reset all default parameters as follows.
If yo
If you
Set Factory Defaults - Scan this bar code to restore the factory default values listed in Table A-1. This
deletes any custom defaults set.
Write to Custom Defaults - Scan this bar code to set the curren t scanner settings as custom default s. Once
set, you can recover custom default settings by scanning Restore Defaults.
u previously set custom defaults by scanning Write to Custom Defa ults, scan Restore Defaults to
retrieve and restore the scanner’s custom default settings.
did not set custom defaults, scan Restore Defaults to restore the factory default values listed in
Table A-1.
User Preferences 4 - 3
*Restore Defaults
Set Factory Defaults
Write to Custom Defaults
4 - 4 LS3408 Product Reference Guide

Parameter Scanning

To disable the decoding of parameter bar codes, including the Set Defaults parameter bar codes, scan the Disable Parameter Scanning bar code below. To enable decoding of parameter bar codes, scan Enable Parameter Scanning.
*Enable Parameter Scanning
Disable Parameter Scanning

Beeper Tone

To select a decode beep frequency (tone), scan the Low Frequency, Medium Frequency, or High Frequency bar code.
Low Frequency
Medium Frequency
*High Frequency

Beeper Volume

To select a beeper volume, scan the Low Volume, Medium Volume, or High Volume bar code.
Low Volume
Medium Volume
User Preferences 4 - 5
*High Volume

Power Mode

This parameter determines whether or not the scanner ente rs re duced po wer mo de a fter a decode attempt. When in reduced power mode, the scanner draws less current from its power source.
*Continuous On
Reduced Power Mode
4 - 6 LS3408 Product Reference Guide

Laser On Time

This parameter sets the maximum time that decode processing continues during a scan attempt. Select a 0.1 second increments from 0.5 to 9.9 seconds. The default Laser On Time is 3.0 seconds.
To set a Laser On Time, scan the bar code below. Next, scan two numeric bar codes in Appendix D, Numeric Bar
Codes that correspond to the desired on time. Enter a leading zero for single digit numbers. For example, to set a
Laser On Time of 0.5 se conds, scan th e bar code be low, then scan the 0 a change the selection, scan Cancel on page D-3.

Beep After Good Decode

Scan a bar code below to select whether or not the scanner beeps af ter a good decode. If you select Do Not Beep After Good Decode, the beeper still operates during parameter menu scanning and indicates error conditions.
nd 5 bar codes. In case of an error, or to
Laser On Time
*Beep After Good Decode
(Enable)
Do Not Beep After Good Decode
(Disable)
User Preferences 4 - 7

Trigger Mode

Set the trigger mode using the bar codes below.
Level Trigger
Upon a trigger pull, an aiming dot appears for a programmable du ration of time. After this time, the aim ing dot turns into a standard laser scanning beam for a full decode sessio n. The laser scanning beam st ays on until the laser-on timeout occurs, a decode occurs, or you release the trigger. If you release the trigger before the aiming duration expires, the laser shuts off an d no decode occurs.
*Level
Two Stage - Option 1
Upon a trigger pull, an aiming dot appears. This aiming dot remains while the trigger is pulled. Releasing the trigger turns the aiming dot into a standard laser scanning beam for a full decode session. The laser scanning beam st ays on until the laser-on timeout occurs or a decode occurs. If you pull the trigger again while in a decode session, the scanner beam returns to an aiming dot.
Two Stage - Option 1
Two Stage - Option 2
Upon a trigger pull, an aiming dot appears. Releasing the trigger turns off the aiming dot. Pulling the trigger twice in rapid succession turns on the standard laser scanning beam for a full decode session. The laser scanning beam stays on until the laser-on timeout occurs, a decode occurs, or you release the trigger.
Two Stage - Option 2
4 - 8 LS3408 Product Reference Guide

Aim Duration

When the scanner is in Level trigger mode (default mode), Aim Duration sets the amount of time the aiming dot displays before turning into a scanning beam. This parameter has no affect when the scanner is in either of the Two Stage trigger modes. See Trigger Mode on page 4-7 for a description of each of th
e trigger modes.
The aim duration is programmable in 0.1 second increments, fr
0.0 seconds. When set to 0.0 seconds, no aiming pattern ap pe a rs be fo re a decod e sessio n . To set an aim duration, scan the bar code below. Then scan two numeric bar codes in Appendix D, Numeric Bar
Codes that correspond to the desired aim duration. Enter a lead
example, to set an aim duration of 0.5 seconds, scan the bar code below, followed by the 0 an case of an error, or to change the selection, scan the Cancel bar code on page D-3.
Aim Duration
om 0.0 to 9.9 seconds. The default Aim Duration is
ing zero for durations less than 1.0 seconds. For
d 5 bar codes. In
Chapter 5 Keyboard Wedge Interface
*North American
Feature/Option
* Indicates Default

Introduction

This chapter provides Keyboard Wedge interface infor m at ion for setting up the scanner. Use this interface type to connect the scanner between the keyboard and host computer. The scanner translates the bar code data into keystrokes. The host computer accepts the keystrokes as if they originate from the keyboard.
This mode of operation adds bar code reading func mode the keyboard keystrokes are simply passed through.
Throughout the programming bar code menus, aste risks (
tionality to a system designed for manual keyboard input. In this
*) indicate default values.
5 - 2 LS3408 Product Reference Guide
Y-cable
Male DIN Host Connector
Female DIN Keyboard ConnectorKeyboard Connector

Connecting a Keyboard Wedge Interface

Figure 5-1
Keyboard Wedge Interface Connection with Y-cable
To connect the keyboard wedge interface Y-cable:
NOTE Interface cables vary depending on configuration. The connectors illustrated in Figure 5-1 are examples
only. The connectors may be different than those illustra same.
1. Turn off the host and unplug the keyboard connector.
2. Attach the modular connector of the Y-cable to the cable interface port on the scanner. (See Installing the
ted, but the steps to connect the scanner are the
Interface Cable on page 1-3.)
3. Connect the round male DIN host connector of the Y-cable to the keyboard port on the host.
4. Connect the round female DIN keyboard connector of the Y-cable to the keyboard connector.
5. If required, attach the optional power supply to the connector in the middle of the Y-cable.
6. Ensure that all connections are secure.
7. Turn on the host system.
8. Select the Keyboard Wedge host type by scanning the appropriate bar code from the Keyboard Wedge Host
Types section onpage 5-4.
9. To modify any other parameter options, scan the appropriate bar codes in this chapter.

Keyboard Wedge Default Parameters

Table 5-1 lists the defaults for Keyboard Wedge host parameters. To change any option, scan the appropriate bar
code(s) provided in the Keyboard Wedge Host Parameters section beginning on page 5-4.
NOTE See Appendix A, Standard Default Parameters for all user preferences, hosts, symbologies, and
miscellaneous default parameters.
Keyboard Wedge Interface 5 - 3
Table 5-1
Keyboard Wedge Host Parameters
Keyboard Wedge Host Type IBM PC/AT& IBM PC Compatibles Keyboard Wedge Country Types
(Country Codes) Ignore Unknown Characters Enable Keystroke Delay 0 msec (No Delay) Intra-Keystroke Delay Disable Alternate Numeric Keypad Emulation Disable Caps Lock On Disable Caps Lock Override Disable Convert Wedge Data Do Not Convert Wedge Data Function Key Mapping Disable FN1 Substitution Disable
Keyboard Wedge Host Default Table
Parameter Default
North American
Page
Number
5-4 5-5
5-7 5-7 5-8 5-8 5-8 5-9 5-9 5-10 5-10
Send Make and Break Send Make and Break Scan Codes
5-10
5 - 4 LS3408 Product Reference Guide

Keyboard Wedge Host Types

Keyboard Wedge Host Types

Scan a bar codes below to select the keyboard wedge host.
*IBM PC/AT & IBM PC Compatibles
IBM PS/2 (Model 30)
IBM AT NOTEBOOK
NCR 7052
Keyboard Wedge Interface 5 - 5

Keyboard Wedge Country Types (Country Codes)

Scan the bar code corresponding to the keyboard type. If your keyboard type does not appear, see Alternate
Numeric Keypad Emulation on page 5-8.
*North American
German Windows
French Windows
French Canadian Windows 95/98
French Canadian Windows XP/2000
French Belgian Windows
5 - 6 LS3408 Product Reference Guide
Keyboard Wedge Country Types (Country Codes) (continued)
Spanish Windows
Italian Windows
Swedish Windows
UK English Windows
Japanese Windows
Brazilian-Portuguese Windows
Keyboard Wedge Interface 5 - 7

Ignore Unknown Characters

Unknown characters are characters the host does not recognize. Select Send Bar Codes With Unknown Characters to send all bar code data except for unknown characters. The scanner sounds no error beeps.
Select Do N character. The scanner sounds an error beep.
ot Send Bar Codes With Unknown Characters to send bar code data up to the first unknown
*Send Bar Codes with Unknown Characters
(Enable)
Do Not Send Bar Codes with Unknown Characters
(Disable)

Keystroke Delay

This is the delay in milliseconds between emulated keystrokes. Scan a bar code below to increase the delay when hosts require slower data transmission.
*0 msec (No Delay)
20 msec (Medium Delay)
40 msec (Long Delay)
5 - 8 LS3408 Product Reference Guide

Intra-Keystroke Delay

Enable this to insert an additional delay between each emulated key depression and release. This sets the Keystroke Delay parameter to a minimum of 5 msec as well.

Alternate Numeric Keypad Emulation

Enable Intra-Keystroke Delay
*Disable Intra-Keystroke Delay
This allows emulation of most other country keyboard types not listed in Keyboard W ed ge Co untry Types (Country
Codes) on page 5-5 in a Microsoft
®
operating system environment.
Enable Alternate Numeric Keypad
*Disable Alternate Numeric Keypad

Caps Lock On

When enabled, the scanner emulates keystrokes as if the Caps Lock key is always pressed.
Enable Caps Lock On
*Disable Caps Lock On
Keyboard Wedge Interface 5 - 9

Caps Lock Override

When enabled, on A T or AT Notebook hosts, the keyboard ignores the st ate of the Cap s Lock key. Therefore, an ‘A’ in the bar code is sent as an ‘A’ no matter what the state of the keyboard’s Caps Lock key.
Enable Caps Lock Override
*Disable Caps Lock Override
NOTE If both Caps Lock On and Caps Lock Override are enabled, Caps Lock Override takes precedence.

Convert Wedge Data

Enable this to convert all bar code data to the selected case.
Convert Wedge Data to Upper Case
Convert Wedge Data to Lower Case
*Do Not Convert Wedge Data
5 - 10 LS3408 Product Reference Guide

Function Key Mapping

ASCII values under 32 are normally sent as control key sequences (see Table 5-2 on page 5-13). Enable this parameter to send the keys in bold in place of the standard key mapping. Table entries that do not have a bold
ntry remain the same whether or not you enable this parameter.
e

FN1 Substitution

Enable Function Key Mapping
*Disable Function Key Mapping
Enable this to replace any FN1 characters in an EAN128 bar code with a user-selected keystroke. See FN1
Substitution Values on page 13-7.
Enable FN1 Substitution
*Disable FN1 Substitution

Send Make and Break

Enable this to prevent sending the scan codes for releasing a key.
*Send Make and Break Scan Codes
Send Make Scan Code Only
Keyboard Wedge Interface 5 - 11
7013
7014 5001 5002 5003 5004 5005 5006 5007 5008 5009 5010
7013
5011
7010 7007
7006 7001
5012
7008
7009
7011
7012
7003
7002 7004 7005
7017 7016
7015
7018
5001
5002
5003
5004
5005
5006
5007
5008
5009
5010
7009
7008
7013
7012
7004
7011
7003
7002
7014
5007
5008
5010
5002
5003
5004
5005 5006
1046
1045
5014
1043
5013
5015
5016
5018
5019
5001
5017
7013
5011
(7013 if double key)
(1048 if double key)
1048
5012
5009

Keyboard Maps

Use the following keyboard maps for reference for prefix/suffix keystroke parameters. To program the prefix/suffix values, see the bar codes on page 13-4.
Figure 5-2
Figure 5-3
IBM PS2 Type Keyboard
IBM PC/AT
Figure 5-4
NCR 7052 32-KEY
5007
5008
5010
5002
5003
5004
5005 5006
1046
1045
5014
1043
5013
5015
5016
5018
5019
1086
1087
1088
1089
1090
5001
1066
1072
1073
1079 1080
1065
1070
1076
1077
1083 1084
1071
1078
1085
1069
5017
7013
5011
1082
1075
1068
1067
(1043 if double key)
(1048 if double key)
1048
5012
5009
1074
1081
5 - 12 LS3408 Product Reference Guide
Figure 5-5
NCR 7052 58-KEY

ASCII Character Set

NOTE Code 39 Full ASCII interprets the bar code special character ($ + % /) preceding a Code 39 character and
assigns an ASCII character value to the pair. For example, if you enable Code 39 Full ASCII and scan a
+B, it transmits as b, %J as ?, and %V as @. Scanning ABC%I outputs the keystroke equivalent of ABC >.
Keyboard Wedge Interface 5 - 13
Table 5-2
Keyboard Wedge ASCII Character Set
ASCII Value
Full ASCII Code 39
Encode Character
1001 $A CTRL A 1002 $B CTRL B 1003 $C CTRL C 1004 $D CTRL D 1005 $E CTRL E 1006 $F CTRL F 1007 $G CTRL G 1008 $H
1009 $I
CTRL H/
CTRL I/ 1010 $J CTRL J 1011 $K CTRL K 1012 $L CTRL L
Keystroke
BACKSPACE
1
HORIZONTAL TAB
1
1013 $M
CTRL M/ 1014 $N CTRL N 1015 $O CTRL O 1016 $P CTRL P 1017 $Q CTRL Q 1018 $R CTRL R 1019 $S CTRL S 1020 $T CTRL T 1021 $U
1
The keystroke in bold is sent only if you enable
page 5-10
. Otherwise, the unbolded keystroke is sent.
CTRL U
Function Key Mapping on
ENTER
1
5 - 14 LS3408 Product Reference Guide
Table 5-2
Keyboard Wedge ASCII Character Set (Continued)
ASCII Value
Full ASCII Code 39
Encode Character
1022 $V CTRL V 1023 $W CTRL W 1024 $X CTRL X 1025 $Y CTRL Y 1026 $Z CTRL Z 1027 %A
CTRL [ / 1028 %B CTRL \ 1029 %C CTRL ] 1030 %D CTRL 6 1031 %E CTRL ­1032 Space Space 1033 /A !
Keystroke
1
ESC
1034 /B “ 1035 /C # 1036 /D $ 1037 /E % 1038 /F & 1039 /G ‘ 1040 /H ( 1041 /I ) 1042 /J * 1043 /K + 1044 /L , 1045 - ­1046 . . 1047 /O / 1048 0 0 1049 1 1
1
The keystroke in bold is sent only if you enable
page 5-10
. Otherwise, the unbolded keystroke is sent.
Function Key Mapping on
Keyboard Wedge Interface 5 - 15
Table 5-2
Keyboard Wedge ASCII Character Set (Continued)
ASCII Value
Full ASCII Code 39
Encode Character
1050 2 2 1051 3 3 1052 4 4 1053 5 5 1054 6 6 1055 7 7 1056 8 8 1057 9 9 1058 /Z : 1059 %F ; 1060 %G < 1061 %H = 1062 %I >
Keystroke
1063 %J ? 1064 %V @ 1065 A A 1066 B B 1067 C C 1068 D D 1069 E E 1070 F F 1071 G G 1072 H H 1073 I I 1074 J J 1075 K K 1076 L L 1077 M M
1
The keystroke in bold is sent only if you enable
page 5-10
. Otherwise, the unbolded keystroke is sent.
Function Key Mapping on
5 - 16 LS3408 Product Reference Guide
Table 5-2
Keyboard Wedge ASCII Character Set (Continued)
ASCII Value
Full ASCII Code 39
Encode Character
1078 N N 1079 O O 1080 P P 1081 Q Q 1082 R R 1083 S S 1084 T T 1085 U U 1086 V V 1087 W W 1088 X X 1089 Y Y 1090 Z Z
Keystroke
1091 %K [ 1092 %L \ 1093 %M ] 1094 %N ^ 1095 %O _ 1096 %W ‘ 1097 +A a 1098 +B b 1099 +C c 1100 +D d 1101 +E e 1102 +F f 1103 +G g 1104 +H h 1105 +I i
1
The keystroke in bold is sent only if you enable
page 5-10
. Otherwise, the unbolded keystroke is sent.
Function Key Mapping on
Keyboard Wedge Interface 5 - 17
Table 5-2
Keyboard Wedge ASCII Character Set (Continued)
ASCII Value
Full ASCII Code 39
Encode Character
1106 +J j 1107 +K k 1108 +L l 1109 +M m 1110 +N n 1111 +O o 1112 +P p 1113 +Q q 1114 +R r 1115 +S s 1116 +T t 1117 +U u 1118 +V v
Keystroke
1119 +W w 1120 +X x 1121 +Y y 1122 +Z z 1123 %P { 1124 %Q | 1125 %R } 1126 %S ~
1
The keystroke in bold is sent only if you enable
page 5-10
Table 5-3
. Otherwise, the unbolded keystroke is sent.
Keyboard Wedge ALT Key Character Set
ALT Keys Keystroke
2065 ALT A 2066 ALT B 2067 ALT C
Function Key Mapping on
2068 ALT D 2069 ALT E
5 - 18 LS3408 Product Reference Guide
Table 5-3
2070 ALT F 2071 ALT G 2072 ALT H 2073 ALT I 2074 ALT J 2075 ALT K 2076 ALT L 2077 ALT M 2078 ALT N 2079 ALT O 2080 ALT P 2081 ALT Q 2082 ALT R
Keyboard Wedge ALT Key Character Set (Continued)
ALT Keys Keystroke
2083 ALT S 2084 ALT T 2085 ALT U 2086 ALT V 2087 ALT W 2088 ALT X 2089 ALT Y 2090 ALT Z
Table 5-4
3000 Right Control Key 3048 GUI 0 3049 GUI 1 3050 GUI 2 3051 GUI 3
Keyboard Wedge GIU Key Character Set
GUI Keys Keystrokes
3052 GUI 4 3053 GUI 5
Keyboard Wedge Interface 5 - 19
Table 5-4
3054 GUI 6 3055 GUI 7 3056 GUI 8 3057 GUI 9 3065 GUI A 3066 GUI B 3067 GUI C 3068 GUI D 3069 GUI E 3070 GUI F 3071 GUI G 3072 GUI H 3073 GUI I
Keyboard Wedge GIU Key Character Set (Continued)
GUI Keys Keystrokes
3074 GUI J 3075 GUI K 3076 GUI L 3077 GUI M 3078 GUI N 3079 GUI O 3080 GUI P 3081 GUI Q 3082 GUI R 3083 GUI S 3084 GUI T 3085 GUI U 3086 GUI V 3087 GUI W 3088 GUI X 3089 GUI Y 3090 GUI Z
5 - 20 LS3408 Product Reference Guide
Table 5-5
5001 F1 5002 F2 5003 F3 5004 F4 5005 F5 5006 F6 5007 F7 5008 F8 5009 F9 5010 F10 5011 F11 5012 F12 5013 F13
Keyboard Wedge F Key Character Set
F Keys Keystroke
5014 F14 5015 F15 5016 F16 5017 F17 5018 F18 5019 F19 5020 F20 5021 F21 5022 F22 5023 F23 5024 F24
Keyboard Wedge Interface 5 - 21
Table 5-6
6042 * 6043 + 6044 undefined 6045 ­6046 . 6047 / 6048 0 6049 1 6050 2 6051 3 6052 4 6053 5 6054 6
Keyboard Wedge Numeric Keypad Character Set
Numeric Keypad Keystroke
6055 7 6056 8 6057 9 6058 Enter 6059 Num Lock
5 - 22 LS3408 Product Reference Guide
Table 5-7
7001 Break 7002 Delete 7003 Pg Up 7004 End 7005 Pg Dn 7006 Pause 7007 Scroll Lock 7008 Backspace 7009 Tab 7010 Print Screen 7011 Insert 7012 Home 7013 Enter
Keyboard Wedge Extended Keypad Character Set
Extended Keypad Keystroke
7014 Escape 7015 Up Arrow 7016 Dn Arrow 7017 Left Arrow 7018 Right Arrow
Chapter 6 RS-232 Interface
*Baud Rate 9600
Feature/Option
* Indicates Default

Introduction

This chapter provides RS-232 host information for setting up the scanner. Use the RS-232 interfaced to attach the scanner to point-of-sale devices, host computers, or other devices with an available RS-232 port (i.e., com port).
If your host does not appear in Table 6-2, set the communicatio n par ameters t o match th e host dev ice. Refe r to the documentation for the host device.
NOTE This scanner uses TTL RS-232 signal levels, which interface with most system architectures. For system
architectures requiring RS-232C signal levels, Zebra offers different cables providing the TTL to RS-232C conversion. Contact
Throughout the programming bar code menus, aste risks (*) indicate default values.
the Zebra Global Customer Support Center for more information.
6 - 2 LS3408 Product Reference Guide
Serial Port Connector to Host
Interface cable
Power supply cable

Connecting an RS-232 Interface

The scanner connects directly to the host computer.
Figure 6-1
Attach the modular connector of the RS-232 interface cable to the cable interface port on the scanner. See
1.
RS-232 Direct Connection
NOTE Interface cables vary depending on configuration. The connectors illustrated in Figure 6-1 are examples
only. The connectors may be different than those illustra same.
ted, but the steps to connect the scanner are the
Installing the Interface Cable on page 1-3.
2. Connect the other end of the RS-232 interface cable to the serial port on the host.
3. Connect the power supply to the serial connector end of the RS-232 interface cable. Plug the power supply to
an appropriate outlet.
4. Ensure that all connections are secure.
5. Select the RS-232 host type by scanning the appropriate bar code from the RS-232 Host Types section on
page 6-6.
6. To modify any other parameter options, scan the appropriate bar codes in this chapter.

RS-232 Default Parameters

Table 6-1 lists the defaults for RS-232 host parameters. To change any option, scan the appropriate bar code(s)
provided in the Parameter Descriptions section beginning on page 6-4.
NOTE See Appendix A, Standard Default Parameters for all user preferences, hosts, symbologies, and
miscellaneous default parameters.
RS-232 Interface 6 - 3
Table 6-1
RS-232 Host Parameters
RS-232 Host Types Standard RS-232 Baud Rate 9600 Parity None Check Receive Errors Enable Stop Bit Select 1 Stop Bit Data Bits 8-Bit Hardware Handshaking None Software Handshaking None Host Serial Response Time-out Minimum: 2 sec RTS Line State Host: Low RTS Beep on <BEL> Disable Intercharacter Delay Minimum: 0 msec
RS-232 Host Default Table
Parameter Default
Page
Number
6-6 6-7 6-8 6-9 6-10 6-10 6-11 6-13 6-15 6-16 6-16 6-17
Nixdorf Beep/LED Options Normal Operation Ignore Unknown Characters Send Bar Code
6-18 6-18
6 - 4 LS3408 Product Reference Guide

RS-232 Host Parameters

Various RS-232 host types use their own parameter default settings. Selecting the host type sets the parameter defaults listed in Table 6-2.
Table 6-2
Parameter
Transmit Code IDNo Yes Yes Yes Yes Yes Yes Yes
Data Trans­mis
Suffix CR/LF
Baud Rate 9600 9600 9600 9600 9600 9600 9600 9600 Parity None Even Odd Odd Even None Odd None Hardware
andshaking
H
Software H
andshaking
Serial Res Time-out
Terminal Specific RS-232
Standard
RS-232
(Default)
Data as is Data/
sion Format
013)
(7
None RTS/CTS
None None None None Ack/Nak None None None
2 Sec. 9.9 Sec. 30.0 Sec. 30.0 Sec. 9.9 Sec. 9.9 Sec. 30.0
ponse
ICL
Suffix
CR (1013)
Option 3
Wincor-
Nixdorf
Mode A
Data/Suffix Data/
CR (1013) CR (1013) ETX
RTS/CTS
Option 3
Wincor-
Nixdorf
Mode B
Suffix
RTS/CTS Option 3
Olivetti Omron
Prefix/ Data/ Suffix
(1002)
None None RTS/CT
Data/
Suffix
CR (1013)
OPOS/
JPOS
Data/
Suffix
CR (1013)
S
Option 3
Sec.
Fujitsu
Data/ Suffix
CR (1013)
None
2 Sec.
Stop Bit Select One One One One One One One One ASCII Format 8-Bit 8-Bit 8-Bit 8-Bit 7-Bit 8-Bit 8-Bit 8-Bit Beep On <BEL> Disable Disable Disable Disable Disable Disable Disable Disable RTS Line State Low High Low Low = No
a to
dat send
Prefix None None
*In the Nixdorf Mode B or OPOS/JPOS, if CTS is low, scanning is disabled. When CTS is high, scanning is enabled. **If you scan Nixdorf Mode B or OPOS/JPOS without connecting the scanner to the proper host, it may appear unable to scan. If this happens, scan a different RS-232 host type within 5 seconds of cycling power to the scanner
.
None None STX
Low High Low =
No data to send
None None None
(1003)
Low
RS-232 Host Parameters (continued)
Selecting the ICL, Wincor-Nixdorf Mode A, Wincor-Nixdorf Mode B, Olivetti, Omron, OPOS/JPOS or Fujitsu host type enables the transmission of code ID characters listed in Table 6-3 below. These code ID characters are not programmable and are separate from the Transmit Code ID feature. Do not enable the Transmit Code ID feature
these terminals.
for
RS-232 Interface 6 - 5
Table 6-3
UPC-A A A A A A A A UPC-E E C C C E C E EAN-8/JAN-8 FF B B B FF B FF EAN-13/JAN-13 F A A A F A F Code 39 C <len> M M M <len> C <len> M None Codabar N <len> N N N <len> N <len> N None Code 128 L <len> K K K <len> L <len> K None I 2 of 5 I <len> I I I <len> I <len> I None Code 93 None L L L <len> None L None D 2 of 5 H <len> H H H <len> H <len> H None GS1-128 L <len> P P P <len> L <len> P None MSI None O O O <len> None O None
Terminal Specific Code ID Characters
Code Type ICL
Wincor-
Nixdorf
Mode A
Wincor-
Nixdorf Mode B
Olivetti Omron
OPOS/
JPOS
Fujitsu
Bookland EAN F A A A F A F Trioptic None None None None None None None Code 11 None None None None None None None IATA H<len> H H None None H None Code 32 None None None None
None None None
6 - 6 LS3408 Product Reference Guide

RS-232 Host Types

To select an RS-232 host type, scan one of the following bar codes.
*Standard RS-23 2
ICL RS-232
Wincor-Nixdorf RS-232 Mode A
Wincor-Nixdorf RS-232 Mode B
Olivetti ORS4500
Omron
OPOS/JPOS
Fujitsu RS-232
RS-232 Interface 6 - 7

Baud Rate

Baud rate is the number of bits of data transmitted per secon d. Set the scanner's baud rate to match the baud rate setting of the host, or data may not reach the host device or may reach it in distorted form.
Baud Rate 600
Baud Rate 1200
Baud Rate 2400
Baud Rate 4800
*Baud Rate 9600
Baud Rate 19,200
Baud Rate 38,400
6 - 8 LS3408 Product Reference Guide

Parity

A parity check bit is the most significant bit of each ASCII coded character. Select the parity type according to host device requirements.
Select Od odd number of 1 bits.
Select Even p an even number of 1 bits.
Select Ma
d parity to set the parity bit value to 0 or 1, based on dat a, to ensure that the code d character cont ains an
arity to set the parity bit value to 0 or 1, based on data, to ensure that the coded character contains
rk parity and the parity bit is always 1.
Odd
Even
Mark
Parity (continued)
Select Space pari ty and the parity bit is always 0.
RS-232 Interface 6 - 9
Space
Select None
when no parity bit is required.
*None

Check Receive Errors

Select whether or not to check the parity, framing, and overrun of received characters. The parity value of received characters is verified against the parity parameter selected above.
*Check For Received Errors (Enable)
Do Not Check For Received Errors (Disable)
6 - 10 LS3408 Product Reference Guide

Stop Bit Select

The stop bit(s) at the end of each transmitted character marks the end of transmission of one character and prepares the receiving device for the next character in the serial da ta stream. Select the number of stop bits (o ne or two) to match the number the receiving terminal is programmed to accommodate. Set the number of stop bits to match host device requirements.
*1 Stop Bit
2 Stop Bits

Data Bits

This parameter allows the scanner to interface with devices requiring a 7-bit or 8-bit ASCII protocol.
7-Bit
*8-Bit
RS-232 Interface 6 - 11

Hardware Handshaking

The data interface consists of an RS-232 port designed to operate either with or without the ha rdware handshaking lines, Request to Send (RTS) and Clear to Send (CTS).
Disable St andard R TS/CTS handsha king to transm it scan dat a as it be handshaking to transmit scan data according to the followin g se qu en ce :
The scanner reads the CTS line for activity. If CTS is de-asserted, the scanner waits up to the Host Serial Response Time-out for the host to de-assert the CTS line. If, after Host Serial Response Time-out (default), the CTS line is still asserted, the scanner sounds a transmit error and discards any scanned data.
When the CTS line is de-asserted, the scanner asserts the RTS line and waits up to the Host Serial Response Time-out for the host to assert CTS. When the host asserts CTS, the data transmits. If, after Host Serial Response Time-out (default), the CTS line is still de-asserted, the scanner sounds a transmit error, and discards the data.
When data transmission completes, the scanner de-asserts RTS 10 msec after sending the last character.
The host should respond by de-asserting CTS. The scanner checks for a de -asserted CTS upon the next transmission of data.
During data transmission, the CTS line should be asserted. If CTS is de-asserted for more than 50 ms between
racters, the scanner aborts transmission, sounds a transmission error, and discards the data.
cha If this communications sequence fails, the sca
be rescanned. If hardware handshaking and software handshaking are
NOTE The DTR signal is jumped to the active state.
nner issues an error indication. In this case, the dat a is lost and must
both enabled, hardware handshaking takes precedence.
comes available. Select St andar d R TS/CTS
None
Scan the bar code below if no hardware handshaking is desired.
*None
Standard RTS/CTS
Scan the bar code below to select Standard RTS/CTS hardware handshaking.
Standard RTS/CTS
6 - 12 LS3408 Product Reference Guide
Hardware Handshaking (continued)
RTS/CTS Option 1
When RTS/CTS Option 1 is selected, the scanner asserts RTS before transmitting and ignores the state of CTS. The scanner de-asserts RTS when the transmission completes.
RTS/CTS Option 2
When Option 2 is selected, RTS is always high or low (user-programmed logic level). However, the scanner waits for CTS to be asserted before transmitting data. If CTS is not asserted within Host Serial Response Time-out (default), the scanner issues an error indication and discards the data.
RTS/CTS Option 1
RTS/CTS Option 2
RTS/CTS Option 3
When Option 3 is selected, the scanner asserts RTS p rior to any dat a transmission, regardless of the st ate of CTS. The scanner waits up to Host Serial Response Time-out (default) for CTS to be asserted. If CTS is not asserted during this time, the scanner issues an error indication and discards the data. The scanner de-asserts RTS when transmission is complete.
RTS/CTS Option 3
RS-232 Interface 6 - 13

Software Handshaking

This parameter offers control of the data transmission process in addition to, or instead of, that offered by hardwa re handshaking. There are five options.
If software handshaking and hardware handshaking are
both enabled, hardware handshaking takes precedence.
None
Select this option to transmit data immediately. No response is expected from host.
*None
ACK/NAK
If you select this option, after transmitting data, the sca nner expects either an ACK or NAK response from the host. When it receives a NAK, the scanner transmits the same data again and waits for either an ACK or NAK. After three unsuccessful attempts to send dat a after r eceiving NAKs, the scanner issues an error indication and discards the data.
The scanner waits up to the programmable Host Serial Response T scanner does not get a response in this time, it issues an error indication and discards the data. There are no retries when a time-out occurs.
ime-out to receive an ACK or NAK. If the
ACK/NAK
ENQ
If you select this option, the scanner waits for an ENQ character from the host before transmitting data. If the scanner does not receive an ENQ within the Host Serial Response T ime-out, the scanne r issues an error indication and discards the data. The host must transmit an ENQ character at least every Host Serial Response Time-out to prevent transmission errors.
ENQ
6 - 14 LS3408 Product Reference Guide
Software Handshaking (continued)
ACK/NAK with ENQ
This combines the two previous options. For re-transmissions of data, due to a NAK from the host, an additional ENQ is not required.
XON/XOFF
An XOFF character turns the scanner transmission off unt il the scanne r receives an XON character. There are two situations for XON/XOFF:
The scanner receives an XOFF before it has dat a to send. When th e scann er has data to send, it waits up to Host Serial Response Time-out for an XON character before transmission. If it does not receive the XON within this time, the scanner issues an error indication and discards the data.
ACK/NAK with ENQ
The scanner receives an XOFF during a transmissi on. Data transmission then stops after sending the current byte. When the scanner receives an XON character, it sends the rest of the data message. The scanner waits up to 30 seconds for the XON.
XON/XOFF
RS-232 Interface 6 - 15

Host Serial Response Time-out

This parameter specifies how long the scanner waits for an ACK, NAK, or CTS before determining that a transmission error occurred. This only applies when in one of the ACK/NAK software handshaking modes, or RTS/CTS hardware handshaking mode.
NOTE This parameter does not apply to the Wincor-Nixdorf RS-232 Mode A/B and the OPOS/JPOS host types.
*Minimum: 2 sec
Low: 2.5 Sec
Medium: 5 Sec
High: 7.5 Sec
Maximum: 9.9 Sec
6 - 16 LS3408 Product Reference Guide

RTS Line State

This parameter sets the idle state of the Serial Host RTS line. Scan a bar code below to select Low RTS or High RTS line state.
*Host: Low RTS
Host: High RTS

Beep on <BEL>

If you enable this parameter, the scanner issues a beep when it detects a <BEL> character on the RS-232 serial line. <BEL> gains a user's attention to an illegal entry or other important event.
Beep On <BEL> Character
(Enable)
*Do Not Beep On <BEL> Character
(Disable)

Intercharacter Delay

This parameter specifies the intercharacter delay inserted between character transmissions.
*Minimum: 0 msec
Low: 25 msec
RS-232 Interface 6 - 17
Medium: 50 msec
High: 75 msec
Maximum: 99 msec
6 - 18 LS3408 Product Reference Guide

Nixdorf Mode A/B and OPOS/JPOS Beep/LED Options

If you selected Nixdorf Mode A, Nixdorf Mode B or OPOS/JPOS, this parameter indicates when the scanner beeps and turns on its LED after a decode.
NOTE The Beep/LED After CTS Pulse option is not valid when Nixdorf Mode A is selected.
*Normal Operation
(Beep/LED Immediately After Decode)
Beep/LED After Transmission
Beep/LED After CTS Pulse

Ignore Unknown Characters

Unknown characters are characters the host does not recognize. Select Send Bar Codes with Unknown Characters to send all bar code data except for unknown characters. The scanner sounds and no error beeps.
Select Do Not Send Bar Codes With Unknown Characters to send bar code data up to the first unknown character. The scanner sounds an error beep.
*Send Bar Code with Unknown Characters
Do Not Send Bar Codes with Unknown Characters

ASCII / Character Set

Assign the values in Table 6-4 as prefixes or suffixes for ASCII character data transmission.
RS-232 Interface 6 - 19
Table 6-4
1000 %U NUL 1001 $A SOH 1002 $B STX 1003 $C ETX 1004 $D EOT 1005 $E ENQ 1006 $F ACK 1007 $G BELL 1008 $H BCKSPC 1009 $I HORIZ TAB 1010 $J LF/NW LN 1011 $K VT 1012 $L FF
RS-232 Prefix/Suffix Values
Prefix/Suffix
Value
Full ASCII Code 39
Encode Character
ASCII Character
1013 $M CR/ENTER 1014 $N SO 1015 $O SI 1016 $P DLE 1017 $Q DC1/XON 1018 $R DC2 1019 $S DC3/XOFF 1020 $T DC4 1021 $U NAK 1022 $V SYN 1023 $W ETB 1024 $X CAN 1025 $Y EM 1026 $Z SUB
6 - 20 LS3408 Product Reference Guide
Table 6-4
1027 %A ESC 1028 %B FS 1029 %C GS 1030 %D RS 1031 %E US 1032 Space Space 1033 /A ! 1034 /B " 1035 /C # 1036 /D $ 1037 /E % 1038 /F & 1039 /G
RS-232 Prefix/Suffix Values (Continued)
Prefix/Suffix
Value
Full ASCII Code 39
Encode Character
ASCII Character
1040 /H ( 1041 /I ) 1042 /J * 1043 /K + 1044 /L , 1045 - ­1046 . . 1047 /O / 1048 0 0 1049 1 1 1050 2 2 1051 3 3 1052 4 4 1053 5 5 1054 6 6 1057 7 7 1056 8 8
RS-232 Interface 6 - 21
Table 6-4
1057 9 9 1058 /Z : 1059 %F ; 1060 %G < 1061 %H = 1062 %I > 1063 %J ? 1064 %V @ 1065 A A 1066 B B 1067 C C 1068 D D 1069 E E
RS-232 Prefix/Suffix Values (Continued)
Prefix/Suffix
Value
Full ASCII Code 39
Encode Character
ASCII Character
1070 F F 1071 G G 1072 H H 1073 I I 1074 J J 1075 K K 1076 L L 1077 M M 1078 N N 1079 O O 1080 P P 1081 Q Q 1082 R R 1083 S S 1084 T T 1085 U U 1086 V V
6 - 22 LS3408 Product Reference Guide
Table 6-4
1087 W W 1088 X X 1089 Y Y 1090 Z Z 1091 %K [ 1092 %L \ 1093 %M ] 1094 %N ^ 1095 %O _ 1096 %W ` 1097 +A a 1098 +B b 1099 +C c
RS-232 Prefix/Suffix Values (Continued)
Prefix/Suffix
Value
Full ASCII Code 39
Encode Character
ASCII Character
1100 +D d 1101 +E e 1102 +F f 1103 +G g 1104 +H h 1105 +I i 1106 +J j 1107 +K k 1108 +L l 1109 +M m 1110 +N n 1111 +O o 1112 +P p 1113 +Q q 1114 +R r 1115 +S s 1116 +T t
RS-232 Interface 6 - 23
Table 6-4
1117 +U u 1118 +V v 1119 +W w 1120 +X x 1121 +Y y 1122 +Z z 1123 %P { 1124 %Q | 1125 %R } 1126 %S ~ 1127 Undefined 7013 ENTER
RS-232 Prefix/Suffix Values (Continued)
Prefix/Suffix
Value
Full ASCII Code 39
Encode Character
ASCII Character
6 - 24 LS3408 Product Reference Guide
Chapter 7 USB Interface
*North American Standard USB Keyboard
Feature/Option
* Indicates Default

Introduction

This chapter provides information for setting up the scanner with a USB host. The scanner connects directly to a USB host, or a powered USB hub, which powers it. No additional power supply is required.
Throughout the programming bar code menus, aste risks (
*) indicate default values.
7 - 2 LS3408 Product Reference Guide
USB Series A Connector
Interface cable

Connecting a USB Interface

Figure 7-1
The scanner connects with USB capable hosts including:
The following operating systems support the scanner through USB:
The scanner also interfaces with other USB hosts whic To set up the scanner:
USB Connection
Desktop PCs and notebooks Apple™ iMacs, Power Mac G4s and G5s, iBooks (North America only), PowerBooks IBM SurePOS terminals Sun, IBM, and other network computers that support more than one keyboard.
Windows® 98, 2000, ME, XP Mac OS 8.5 and above IBM 4690 OS.
h support USB Human Interface Devices (HID).
NOTE Interface cables vary depending on configuration. The connectors illustrated in Figure 7-1 are examples
only. The connectors may be different than those illustra same.
ted, but the steps to connect the scanner are the
1.
Attach the modular connector of the USB interface cable to the cable interface port on the scanner. See
Installing the Interface Cable on page 1-3.
2. Plug the series A connector in the USB host or hub, or plug the Plus Power connector in an available port of
the IBM SurePOS terminal.
3. Ensure all connections are secure.
4. Select the USB device type by scanning the appropriate ba r cod e from USB Device Type on page 7-4.
5. On first installation when using Windows, the software displays a prompt to select or install the Human
Interface Device driver. To install this driver, provided by Windows, click Next through all the choices and click Finished on the last choice. The scanner powers up during this installation.
6. To modify any other parameter options, scan the appropriate bar codes in this chapter.
If there are any problems with the system, see Troubleshooting on page 3-2.

USB Default Parameters

Table 7-1 lists the defaults for USB host parameters. To change any option, scan the appropriate bar code(s)
provided in the Parameter Descriptions section beginning on page 7-4.
NOTE See Appendix A, Standard Default Parameters for all user preferences, hosts, symbologies, and
miscellaneous default parameters.
USB Interface 7 - 3
Table 7-1
USB Host Parameters
USB Device Type HID Keyboard Emulation USB Country Keyboard Types (Country Codes) North American USB Keystroke Delay No Delay (0 msec) USB CAPS Lock Override Disable USB Ignore Unknown Characters Enable Emulate Keypad Disable USB Keyboard FN1 Substitution Disable Function Key Mapping Disable Simulated Caps Lock Disable Convert Case No Case Conversion
USB Host Default Table
Parameter Default
Page
Number
7-4 7-5 7-7 7-8 7-8 7-9 7-9 7-10 7-10 7-11
7 - 4 LS3408 Product Reference Guide

USB Host Parameters

USB Device Type

Select the desired USB device type.
NOTE When changing USB Device Types, the scanner automatically resets and issues the standard startup
beep sequences.
*HID Keyboard Emulation
IBM Table Top USB
IBM Hand-Held USB
USB Interface 7 - 5

USB Country Keyboard Types (Country Codes)

Scan the bar code corresponding to the keyboard type. This setting applies only to the USB HID Keyboard Emulation device.
NOTE When changing USB Country Keyboard Types, the scanner automatically resets and issues the standard
startup beep sequences.
*North American Standard USB Keyboard
German Windows
French Windows
French Canadian Windows 95/98
French Canadian Windows 2000/XP
7 - 6 LS3408 Product Reference Guide
USB Country Keyboard Types (Country Codes) (continued)
French Belgian Windows
Spanish Windows
Italian Windows
Swedish Windows
UK English Windows
Loading...