York DM150 User Manual
036-21044-003-A-0304
TECHNICAL
TECHNICAL
GUIDE 50Hz
GUIDE 50Hz
TM
SINGLE PACKAGE AIR CONDITIONERS AND
SINGLE PACKAGE GAS/ELECTRIC UNITS
DM090, 120, 150
7-1/2, 10, 12-1/2 NOMINAL TONS
9.0 - 10.0 EER
380/415-3-50
®
DESCRIPTION
YORK® Predator® units are convertible single packages with a
common footprint cabinet and common roof curb for all 7-1/2
through 12-1/2 ton models. All units have two compressors with
independent refrigeration circuits. The units were designed for
light commercial applications and can be easily installed on a roof
curb, slab, roof jack, or frame.
All Predator® units are self-contained and assembled on rigid full
perimeter base rails allowing for 3-way forklift access and over
head rigging. Every unit is completely charged, wired, piped, and
tested at the factory to provide a quick and easy field installation.
All units are convertible between side and down airflow. A single
economizer design is used on side and down discharge applica
tions, as well as all tonnage sizes.
Predator® units are available in the following configurations: cooling only, cooling with electric heat, and cooling with gas heat.
Electric heaters are available as factory-installed options or as
field-installed accessories.
-
-
FOR DISTRIBUTION USE ONLY - NOT TO BE USED AT POINT OF RETAIL SALE
TABLE OF CONTENTS
036-21044-003-A-0304
DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
FACTORY INSTALLED OPTIONS . . . . . . . . . . . . . . 5
FIELD INSTALLED ACCESSORIES . . . . . . . . . . . . 6
NOMENCLATURE . . . . . . . . . . . . . . . . . . . . . . . . . . 8
LIST OF FIGURES
Fig. # Pg. #
1 PREDATOR® COMPONENT LOCATION . . . . . . . . . . . 3
2 UNIT 4 POINT LOAD . . . . . . . . . . . . . . . . . . . . . . . . . . 31
3 UNIT CENTER OF GRAVITY . . . . . . . . . . . . . . . . . . .31
4 UNIT 6 POINT LOAD . . . . . . . . . . . . . . . . . . . . . . . . . . 31
5 UNIT DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
6 PREDATOR® ROOF CURB DIMENSIONS . . . . . . . . . 33
7 SUNLINE™ TO PREDATOR® TRANSITION
ROOF CURB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
8 BOTTOM DUCT OPENINGS (FROM ABOVE) . . . . . . 34
9 REAR DUCT DIMENSIONS . . . . . . . . . . . . . . . . . . . . . 34
10 COOLING UNIT WITH GAS HEAT WIRING
DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
11 COOLING UNIT WITH/WITHOUT ELECTRIC HEAT
WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
LIST OF TABLES
Tbl. # Pg. #
1 PHYSICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2 CAPACITY RATINGS IMPERIAL . . . . . . . . . . . . . . . . . 13
3 CAPACITY RATINGS METRIC . . . . . . . . . . . . . . . . . . 13
4 COOLING CAPACITY 7-1/2 TON UNIT - IMPERIAL . . 14
5 COOLING CAPACITY 26.4 KW UNIT - METRIC . . . . . 15
6 COOLING CAPACITY 10 TON UNIT - IMPERIAL . . . . 16
7 COOLING CAPACITY 35.1 KW UNIT - METRIC . . . . . 17
8 COOLING CAPACITY 12-1/2 TON UNIT - IMPERIAL . 18
9 COOLING CAPACITY 43.9 KW UNIT - METRIC . . . . . 19
10 ELECTRICAL DATA 7-1/2 TON . . . . . . . . . . . . . . . . . . 20
11 ELECTRICAL DATA 10 TON . . . . . . . . . . . . . . . . . . . . 20
12 ELECTRICAL DATA 12-1/2 TON . . . . . . . . . . . . . . . . 20
13 BLOWER PERFORMANCE 7-1/2 TON STANDARD
MOTOR - SIDE DUCT (IMPERIAL) . . . . . . . . . . . . . . . 21
14 BLOWER PERFORMANCE 7-1/2 TON STANDARD
MOTOR - SIDE DUCT (METRIC) . . . . . . . . . . . . . . . .21
15 BLOWER PERFORMANCE 7-1/2 TON OPTIONAL
MOTOR - SIDE DUCT (IMPERIAL) . . . . . . . . . . . . . . 21
Tbl. # Pg. #
16 BLOWER PERFORMANCE 7-1/2 TON OPTIONAL
MOTOR - SIDE DUCT (METRIC) . . . . . . . . . . . . . . . . 22
17 BLOWER PERFORMANCE 10 TON STANDARD
MOTOR - SIDE DUCT (IMPERIAL) . . . . . . . . . . . . . . . 22
18 BLOWER PERFORMANCE 10 TON STANDARD
MOTOR - SIDE DUCT (METRIC) . . . . . . . . . . . . . . . . 22
19 BLOWER PERFORMANCE 10 TON OPTIONAL
MOTOR - SIDE DUCT (IMPERIAL) . . . . . . . . . . . . . . 23
20 BLOWER PERFORMANCE 10 TON OPTIONAL
MOTOR - SIDE DUCT (METRIC) . . . . . . . . . . . . . . . . 23
21 BLOWER PERFORMANCE 12-1/2 TON - SIDE
DUCT (IMPERIAL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
22 BLOWER PERFORMANCE 12-1/2 TON - SIDE
DUCT (METRIC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
23 BLOWER PERFORMANCE 7-1/2 TON STANDARD
MOTOR - DOWNSHOT (IMPERIAL) . . . . . . . . . . . . . . 25
24 BLOWER PERFORMANCE 7-1/2 TON STANDARD
MOTOR - DOWNSHOT (METRIC) . . . . . . . . . . . . . . . 25
25 BLOWER PERFORMANCE 7-1/2 TON OPTIONAL
MOTOR - DOWNSHOT (IMPERIAL) . . . . . . . . . . . . . . 25
26 BLOWER PERFORMANCE 7-1/2 TON OPTIONAL
MOTOR - DOWNSHOT (METRIC) . . . . . . . . . . . . . . . 26
27 BLOWER PERFORMANCE 10 TON STANDARD
MOTOR - DOWNSHOT (IMPERIAL) . . . . . . . . . . . . . . 26
28 BLOWER PERFORMANCE 10 TON STANDARD
MOTOR - DOWNSHOT (METRIC) . . . . . . . . . . . . . . . 26
29 BLOWER PERFORMANCE 10 TON OPTIONAL
MOTOR - DOWNSHOT (IMPERIAL) . . . . . . . . . . . . . . 27
30 BLOWER PERFORMANCE 10 TON OPTIONAL
MOTOR - DOWNSHOT (METRIC) . . . . . . . . . . . . . . . 27
31 BLOWER PERFORMANCE 12-1/2 TON - DOWNSHOT
(IMPERIAL) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
32 BLOWER PERFORMANCE 12-1/2 TON - DOWNSHOT
(METRIC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
33 ADDITIONAL STATIC RESISTANCE (IMPERIAL) . . . 29
34 ADDITIONAL STATIC RESISTANCE (METRIC) . . . . 30
35 ELECTRIC HEAT MINIMUM SUPPLY AIR
- IMPERIAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
36 ELECTRIC HEAT MINIMUM SUPPLY AIR
- METRIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
37 INDOOR BLOWER SPECIFICATIONS . . . . . . . . . . . . 31
38 4 POINT LOAD WEIGHT . . . . . . . . . . . . . . . . . . . . . . . 31
39 6 POINT LOAD WEIGHT . . . . . . . . . . . . . . . . . . . . . . . 31
40 UNIT WEIGHT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
41 UNIT CLEARANCES . . . . . . . . . . . . . . . . . . . . . . . . . 32
2 Unitary Products
036-21044-003-A-0304
Terminal Block
for Hi-Voltage
Connection
Second model
nameplate inside
hinged access
panel
Dual stage
cooling for
maximum
comfort
Compressor
#2 Access
(High-Eff
Compressor
w/ crankcase
heater)
Base Rails w/ Forklift Slots (3 Sides) &
Lifting Holes
Roof curbs in eight- and
fourteen-inch heights.
Roof curbs for transitioning
from York Sunline™ footprint to the DM Series footprint are also available
(field-installed accessory)
3FJMIF@FQV
Screw Connector for T-stat
Wiring and Network Connection
™ Control Board w/
To ol - le s s
door latch
Side entry power
and control wiring
knockouts
Disconnect Location
(Optional Disconnect Switch)
Slide-Out Drain
Pan w/ Steel 3/4”
NPT Connection
Compressor #1 Access (High-Eff
Compressor w/ crankcase heater)
Filter Access
(2” Filters)
Filter-Drier (Solid Core)
Condenser
Section
Slide-out motor
and blower
assembly for
easy adjustment
and service
Belt-Drive
Blower Motor
Power Ventor Motor
20-gauge aluminized
steel tubular heat
exchanger for long life
(stainless steel option)
Two-stage gas heat-
ing to maintain
warm, comfortable
temperature
Intelligent control board for
safe and efficient operation
FIGURE 1 - PREDATOR® COMPONENT LOCATION
FEATURES
• Standard Efficiency– All standard efficiency units have
a minimum EER of 9.0 (2.64 CoP). Gas/electric units
have electronic spark ignition and power vented combustion with steady state efficiencies of 80%.
• Service Friendly – The Predator® incorporates a num-
ber of enhancements which improve serviceability.
The motor and blower slide out of the unit as a common
assembly. This facilitates greater access to all the indoor
airflow components, thus simplifying maintenance and
adjustment.
Service time is reduced through the use of hinged, toolless panels. Such panels provide access to frequently
inspected components and areas, including the control
box, compressors, filters, indoor motor & blower, and the
heating section. The panels are screwed in place at the
factory to prevent access by children or other unautho
rized persons. It is recommended that the panels be
secured with screws once service is complete.
Service windows have been placed in both condenser
section walls. Rotation of the cover allows easy access
to the condenser coils for cleaning or inspection.
Both the unit control board and ignition control board utilize flash codes to aid in diagnosis of unit malfunctions.
Unique alarm codes quickly identify the source of the
unit alarm.
All units use the same standard filter size. This standardization removes any confusion on which filter sizes
are needed for replacement.
The non-corrosive drain pan slides out of the unit to permit easy cleaning. The drain pan is accessed by removing the drain pan cover plate on the rear of the unit.
Once the plate is removed, the drain pan slides out
through the rear of the unit.
All Predator® units have a second model nameplate
located inside the control access door. This is to prevent
-
deterioration of the nameplate through weathering.
• Environmentally Aware – For improved Indoor Air
Quality, foil faced insulation is used exclusively through
out the units.
-
Unitary Products 3
036-21044-003-A-0304
• Balanced Heating – The Predator® offers “Ultimate
Heating Comfort” with a balance between 1
stage gas heating. The 1
st
stage of a gas heat Predator®
st
and 2nd
unit provides 60% of the heating capacity. Balanced
heating allows the unit to better maintain desired temper
atures.
• Convertible Airflow Design – The side duct openings
are covered when they leave the factory. If a side sup
ply/return is desired, the installer simply removes the two
side duct covers from the outside of the unit and installs
them over the down shot openings. No panel cutting is
required. Convertible airflow design allows maximum
field flexibility and minimum inventory.
• System Protection - Suction line freezestats are sup-
plied on all units to protect against loss of charge and coil
frosting when the economizer operates at low outdoor air
temperatures while the compressors are running. Every
unit has solid-core liquid line filter-driers and high and
low-pressure switches. Internal compressor protection is
standard on all compressors. Crankcase heaters are
standard on reciprocating compressors. Scroll compres
sors do not require crankcase heaters. Phase Monitors
are standard on units with scroll compressors. This
accessory monitors the incoming power to the unit and
protects the unit from phase loss and reversed phase
rotation.
• Advanced Controls - 3FJMIF@FQV™ control boards have
standardized a number of features previously available
only as options or by utilizing additional controls.
• Low Ambient - An integrated low-ambient control
allows all units to operate in the cooling mode down
to 0°F (-17.8°C) outdoor ambient without additional
assistance. Optionally, the control board can be
programmed to lockout the compressors when the
outdoor air temperature is low or when free cooling
is available.
• Anti-Short Cycle Protection - To aid compressor
life, an anti-short cycle delay is incorporated into the
standard controls. Compressor reliability is further
ensured by programmable minimum run times. For
testing, the anti-short cycle delay can be temporarily
overridden with the push of a button.
• Fan Delays - Fan on and fan off delays are fully pro-
grammable. Furthermore, the heating and cooling
fan delay times are independent of one another. All
units are programmed with default values based
upon their configuration of cooling and heat.
• Safety Monitoring - The control board monitors the
high and low-pressure switches, the freezestats, the
gas valve, if applicable, and the temperature limit
switch on gas and electric heat units. The unit con
trol board will alarm on ignition failures, compressor
lockouts and repeated limit switch trips.
• Nuisance Trip Protection and Strikes - To prevent
nuisance trouble calls, the control board uses a
“three times, you’re out” philosophy. The high and
low-pressure switches and the freezestats must trip
-
three times within two hours before the unit control
board will lock out the associated compressor.
-
• On Board Diagnostics - Each alarm will energize a
trouble light on the thermostat, if so equipped, and
flash an alarm code on the control board LED. Each
high and low-pressure switch alarm as well as each
freezestat alarm has its own flash code. The control
board saves the five most recent alarms in memory,
and these alarms can be reviewed at any time.
Alarms and programmed values are retained
through the loss of power.
• Reliable – From the beginning – All units undergo com-
puter automated testing before they leave the factory.
Units are tested for refrigerant charge and pressure, unit
amperage, and 100% functionality. For the long term –
All Predator
®
units are painted with a long lasting, powder paint that stands up over the life of the unit. The paint
used has been proven by a 750 hour salt spray test.
• Flexible Placement – All models and configurations
share the same cabinet/footprint and thus the same roof
curb. You have the flexibility to set one curb and choose
the correct tonnage size and heating option after the
internal loads have been determined.
To further simplify planning and installation, Predator
cabinets are designed to fit your roof. With the optional
roof curb, the unit ductwork is designed to fit around 24”
(610 mm) on-center joists or between 48” (1219 mm) oncenter joists.
The drain pan can be rotated to drain to either the front
or the rear of the unit. Additionally, the drain pan can be
piped to drain through the roof curb. As it is sometimes
difficult to have a level installation, the drain pan features
a generous slope to ensure proper drainage.
• Full Perimeter Base Rails – The permanently attached
base rails provide a solid foundation for the entire unit
and protect the unit during shipment. The rails offer forklift access from 3 sides, and rigging holes are available
so that an overhead crane can be used to place the units
on a roof.
• Easy Installation – Gas and electric utility knockouts are
supplied in the unit underside as well as the side of the
unit. A clearly identified location is provided to mount a
field supplied electrical disconnect switch. Utility con
nections can be made quickly and with a minimum
amount of field labor.
All units are shipped with 2” (51 mm) filters installed.
®
-
4 Unitary Products
036-21044-003-A-0304
• Wide Range of Indoor Airflows – All indoor fan motors
are belt-drive type providing maximum flexibility to han
dle most airflow requirements. For high static applications, factory installed alternate indoor fan motors are
available. With the optional indoor fan motor, all units
can supply nominal airflow at a minimum of 1.5” (375 Pa)
ESP.
FACTORY INSTALLED OPTIONS
YORK® offers several equipment options factory installed, for
the Predator
• Downflow Economizer - (With barometric relief) - The
economizer is provided with a single enthalpy input. The
economizer is 2% low leakage type, and is shipped
installed and wired. The installer needs only to assemble
and mount the outdoor air hood (Provided). The econo
mizer has spring return, fully modulating damper actuators and is capable of introducing up to 100% outdoor air.
As the outdoor air intake dampers open, the return air
dampers close. The changeover from mechanical refrig
eration to economizer operation is regulated by the standard single enthalpy input. There is an optional input
dual dry bulb available. To meet regulated air standards,
the economizer control accepts an optional CO
demand ventilation. With single enthalpy input, the economizer control monitors outdoor air. The dual enthalpy kit
provides a second input used to monitor the return air.
With a dual input kit installed, the economizer control
compares the values of the two enthalpy or temperature
inputs and positions the dampers to provide the maxi
mum efficiency possible.
• Horizontal Economizer - (Without barometric relief) -
All features as the downflow economizer exist except
you must order the barometric relief separately. You
must order a 1EH0408 if you are installing a power
exhaust. You can order a 1RD0411 Barometric Relief
for horizontal flow economizers only.
• BAS Ready Economizer -(With barometric relief) -
The economizer is provided with a Belimo actuator that
requires a 0-10V DC input from an external source (i.e.,
field installed building automation system controller).
Power exhaust options are available. The economizer is
2% low leakage type with spring return and fully modu
lating dampers capable of introducing up to 100% outside air. Also include 2” (51 mm) pleated filters.
• Power Exhaust (Downflow only) - This accessory
installs in the unit with a down flow economizer.
• Motorized Outdoor Air Damper - The motorized out-
door air damper includes a slide-in/plug-in damper
assembly with an outdoor air hood and filters. The out
door air dampers open to the preset position when the
indoor fan motor is energized. The damper has a range
of 0% to 100% outdoor air entry. Factory installed option
or field installed accessory.
®
line.
input for
2
-
-
-
-
-
• Alternate Indoor Blower Motor - For applications with
-
high static restrictions, units are offered with optional
indoor motors that provide higher static output and/or
higher airflow, depending upon the installer’s needs.
• Aluminized Steel Gas Heat Exchanger - For applica-
tions in non-corrosive environments.
• Stainless Steel Gas Heat Exchanger - For applications
in corrosive environments, this option provides a full
stainless steel heat exchanger assembly.
• Electric Heaters - The electric heaters range from 9kW
to 54kW and are available in all the voltage options of the
base units. All heaters are dual staged. All heaters are
intended for single point power supply.
• Disconnect Switch - For gas heat units and cooling
units with electric heat, a HACR breaker sized to the unit
is provided. For cooling only units, a switch sized to the
largest electric heat available for the particular unit is
provided. Factory installed option only.
• Smoke Detectors - The smoke detectors stop operation
of the unit by interrupting power to the control board if
smoke is detected within the air compartment. Available
for both the supply and/or return air.
• Phase Monitors - Designed to prevent unit damage.
The phase monitor will shut the unit down in an out-of
phase condition. (Standard on units with Scroll Com-
pressors.)
• Coil Guard - Customers can purchase a coil guard kit to
protect the condenser coil from damage. Additionally,
this kit stops animals and foreign objects from entering
the space between the inner condenser coil and the
main cabinet. This is not a hail guard kit.
• Dirty Filter Switch - This kit includes a differential pres-
sure switch that energizes the fault light on the unit thermostat, indicating that there is an abnormally high
pressure drop across the filters. Factory installed option
or field installed accessory.
• Technicoat Condenser Coils - The condenser coils are
coated with a phenolic coating for protection against cor
rosion due to harsh environments.
• Technicoat Evaporator Coil - The evaporator coils are
coated with a phenolic coating for protection against cor
rosion due to harsh environments.
• Novar® BAS Control - The Novar® ETC-3 building
automation system controller is factory installed. Incudes
supply air sensor, return air sensor, dirty filter indicator
switch, and air proving switch.
• Johnson Controls BAS Control - The Johnson Control
YK-UNT-1126 building automation system controller is
factory installed. Includes supply air sensor, return air
sensor, dirty filter indicator switch, and air proving switch.
-
-
Unitary Products 5
036-21044-003-A-0304
• CPC BAS Control - The Computer Process Controls
Model 810-3060 ARTC Advanced Rooftop building auto
mation system controller is factory installed. Includes
supply air sensor, return air sensor, dirty filter indicator
switch, and air proving switch.
• Honeywell BAS Control - The Honeywell W7750C
building automation system controller is factory installed.
Includes air supply sensor, return air sensor, dirty filter
indicator switch, and air proving switch.
FIELD INSTALLED ACCESSORIES
YORK® offers several equipment accessories for field installation, for the Predator
• Downflow Economizer - (With barometric relief) - The
economizer is provided with a single enthalpy input. The
economizer is 2% low leakage type. The economizer has
spring return, fully modulating damper actuators and is
capable of introducing up to 100% outdoor air. As the
outdoor air intake dampers open, the return air dampers
close. The changeover from mechanical refrigeration to
economizer operation is regulated by the standard single
enthalpy input. There is an optional input dual dry bulb
available. To meet regulated air standards, the econo
mizer control accepts an optional CO
ventilation. With single enthalpy input, the economizer
control monitors outdoor air. The dual enthalpy kit provides a second input used to monitor the return air. With
a dual input kit installed, the economizer control com
pares the values of the two enthalpy or temperature
inputs and positions the dampers to provide the maxi
mum efficiency possible
• Horizontal Economizer - (Without barometric relief) -
All features as the downflow economizer exist except
you must order the barometric relief separately. You
must order a 1EH0408 if you are installing a power
exhaust. You can order a 1RD0411 Barometric Relief
for horizontal flow economizer.
• Dual Enthalpy Control, Accessory - This kit contains
the required components to convert a single enthalpy
economizer to dual enthalpy.
• Barometric Relief Damper - Zero to 100% capacity
barometric relief dampers for use with horizontal flow, or
field installed slab economizers.
• Power Exhaust - This accessory installs in the unit with
a down flow economizer. Power exhaust plugs into the
connector in the unit bulkhead. You must purchase
1EH0408 barometric relief/power exhaust hood when
applying to a horizontal flow application.
• Manual Outdoor Air Damper - Like the motorized out-
door air damper, each manual outdoor air damper
includes a slide-in damper assembly with an outdoor air
hood and filters. Customers have a choice of dampers
with ranges of 0% to 100% or 0% to 35% outdoor air
entry.
®
line.
input for demand
2
-
-
-
• Motorized Outdoor Air Damper - The motorized out-
-
door air damper includes a slide-in/plug-in damper
assembly with an outdoor air hood and filters. The out
door air dampers open to the preset position when the
indoor fan motor is energized. The damper has a range
of 0% to 100% outdoor air entry. Factory installed option
or field installed accessory.
• Smoke Detectors - The smoke detectors stop operation
of the unit by interrupting power to the control board if
smoke is detected within the air compartment.
• CO2 Sensor - Senses CO2 levels and automatically
overrides the economizer when levels rise above the
preset limits.
• Dirty Filter Switch - This kit includes a differential pres-
sure switch that energizes the fault light on the unit thermostat, indicating that there is an abnormally high
pressure drop across the filters.
• Coil Guard - Field installed decorative wire coil guard.
• Hail Guard - This kit includes a sloped hood which
installs over the outside condenser coil and prevents
damage to the coil fins from hail strikes. Field installed
accessory only.
• Flue Exhaust Extension Kit - In locations with wind or
weather conditions which may interfere with proper
exhausting of furnace combustion products, this kit can
be installed to prevent the flue exhaust from entering
nearby fresh air intakes.
• -60°F Gas Heat Kit - For installations which require gas
heat units to perform in low ambient temperatures, a gas
section heating kit is available. This kit provides electric
heat in the gas heat controls section to ensure the gas
valve and controls will continue to function properly at
extremely low temperatures.
• Gas Heat High Altitude Kit - This kit converts a gas
heat unit to operate at high altitudes, 2,000 to 6,000 feet.
Conversion kits are available for natural gas and pro
pane.
• Gas Heat Propane Conversion Kit - This kit converts a
gas-fired heater from natural gas to propane. It contains
the main burner orifices and gas valve replacement
springs.
• Gas Piping Kit - Contains pipe nipples, fittings and gas
cock required for gas supply connection with external
shut off.
• Electric Heaters - The electric heaters range from 9 kW
to 54kW and are available in all the voltage options of the
base units. All heaters are dual staged. Cooling units
include an adapter panel for easy installation of the elec
tric heaters. Necessary hardware and connectors are
included with the heaters. All heaters are intended for
single point power supply.
-
-
-
6 Unitary Products
036-21044-003-A-0304
• Low Limit / Compressor Lockout Kit
1. Compressor Lockout (CLO): To prevent mechani-
cal (compressorized) operation of the unit during
cold outdoor conditions where there is a risk of
returning liquid refrigerant back to the compressors.
2. Low Limit Control (LLC): To prevent the supply air
from dropping below a specified setpoint by utilizing
the units first stage heating means when there is a
demand for cooling during cold outside conditions.
• Metal Frame Filter Kit - Metal frame with polyester filter
medium.
• Permanent Filters - Permanent filters are available.
• Roof Curbs - The roof curbs have insulated decks and
are shipped disassembled The roof curbs are available
in 8” (203 mm) and 14” (356 mm) heights. For applications with security concerns, burglar bars are available
for the duct openings of the roof curbs.
• Roof Curb Transition - Single Piece Adapter (10” (254
mm) High) - Roof curbs for transitioning from Sunline™
units to Predator® Magnum. Fits 7.5 to 12.5 Sunline™
roof curbs only.
• Burglar Bars - Mount in the supply and return openings
to prevent entry into the duct work.
• Thermostat - The units are designed to operate with 24-
volt electronic and electro-mechanical thermostats. All
units (with or without an economizer) operate with twostage heat/two-stage cool or two-stage cooling only ther
mostats, depending upon unit configuration.
-
Unitary Products 7
NOMENCLATURE
7½ - 12½ Ton Predator Model Number Nomenclature
036-21044-003-A-0304
D M N10
Product Category
D = Air Cond., Single Package
Product Identifier
M = R-22 Standard Efficiency
Nominal Cooling Capacity - MBH
090 = 7-½ Ton
120 = 10 Ton
150 = 12-½ Ton
Heat Type & Nominal Heat Capacity
C00 = Cooling Only. Suitable for field installed electric heat
Gas Heat Options
N10 = 100 MBH Output Aluminized Steel
N15 = 150 MBH Output Aluminized Steel
S10 = 100 MBH Output Stainless Steel
S15 = 150 MBH Output Stainless Steel
Electric Heat Options
E09 = 9 kW Electric Heat
E18 = 18 kW Electric Heat
E24 = 24 kW Electric Heat
E36 = 36 kW Electric Heat
E54 = 54 kW Electric Heat
A7A
Voltage
7 = 380/415-3-50
AA 3090
Installation Options
A = No Options Installed
B = Option 1
C = Option 2
D = Options 1 & 2
E = Option 3
F = Option 4
G = Options 1 & 3
H = Options 1 & 4
J = Options 1, 2 & 3
K = Options 1, 2 & 4
L = Options 1, 3 & 4
M = Options 1, 2, 3 & 4
N = Options 2 & 3
P = Options 2 & 4
Q = Options 2, 3 & 4
R = Options 3 & 4
1 = Disconnect
2 = Non-Pwr’d Conv Outlet
3 = Smoke Detector S. A.
4 = Smoke Detector R. A.
Product Generation
3 = Third Generation
Additional Options
(See Next Page)
Options
Airflow
A = Standard Motor
B = Standard Motor/Economizer/Barometric Relief (Downflow only)
C = Standard Motor/Economizer/Power Exhaust (Downflow only)
D = Standard Motor/Motorized Damper (Downflow only)
E = Standard Motor/Horizontal Economizer (No Barometric Relief)
L = Standard Motor/BAS Ready Econ (NoBASController)/Barometric Relief w/2" Pleated Filters (Downflow only)
M = Standard Motor/BAS Ready Econ (NoBASController)/Power Exhaust w/2" Pleated Filters (Downflow only)
N = High Static Motor
P = High Static Motor/Economizer/Barometric Relief (Downflow only)
Q = High Static Motor/Economizer/Power Exhaust (Downflow only)
R = High Static Motor/Motorized Damper (Downflow only)
S = High Static Motor/Horizontal Eco nomizer (No Barometric Relief)
Y = High Static Motor/BAS Ready Econ (NoBASController)/Barometric Relief w/2" Pleated Filters (Downflow only)
Z = High Static Motor/BAS Ready Econ (NoBASController)/Power Exhaust w/2" Pleated Filters (Downflow only)
8 Unitary Products
036-21044-003-A-0304
NOMENCLATURE ADDITIONAL OPTIONS:ì
AA None
AB Phase Monitor
AC Coil Guard
AD Dirty Filter Switch
AE Phase Monitor & Coil Guard
AF Phase Monitor & Dirty Filter Switch
AG Coil Guard & Dirty Filter Switch
AH Phase Monitor, Coil Guard, & Dirty Filter Switch
CA CPC Controller with Dirty Filter Switch & Air Proving Switch
CB CPC Controller, DFS, APS & Phase Monitor
CC CPC Controller, DFS, APS & Coil Guard
CD CPC Controller, DFS, APS, Phase Monitor, & Coil Guard
CE CPC Controller, DFS, APS & Technicoat Cond. Coil
CF CPC Controller, DFS, APS, Technicoat Cond. Coil, & Phase Monitor
CG CPC Controller, DFS, APS, Technicoat Cond. Coil, & Coil Guard
CH CPC Controller, DFS, APS, Technicoat Cond. Coil, Phase Monitor, & Coil Guard
CJ CPC Controller, DFS, APS & Technicoat Evap. Coil
CK CPC Controller, DFS, APS, Technicoat Evap. Coil, & Phase Monitor
CL CPC Controller, DFS, APS, Technicoat Evap. Coil, & Coil Guard
CM CPC Controller, DFS, APS, Technicoat Evap. Coil, Phase Monitor, & Coil Guard
CN CPC Controller, DFS, APS & Technicoat Evap. & Cond Coils
CP CPC Controller, DFS, APS, Technicoat Evap. & Cond Coils, & Phase Monitor
CQ CPC Controller, DFS, APS, Technicoat Evap. & Cond Coils, & Coil Guard
CR CPC Controller, DFS, APS, Technicoat Cond Coils, Phase Monitor, & 2” Pleated Filters
CV CPC Controller, DFS, APS, & 2” Pleated Filters
CX CPC Controller, DFS, APS, Technicoat Evap. & Cond Coils, Phase Monitor, Coil Guard
HA Honeywell Excel 10 Controller with Dirty Filter Switch & Air Proving Switch
HB Honeywell Excel 10 Controller, DFS, APS & Phase Monitor
HC Honeywell Excel 10 Controller, DFS, APS & Coil Guard
HD Honeywell Excel 10 Controller, DFS, APS, Phase Monitor, & Coil Guard
HE Honeywell Excel 10 Controller, DFS, APS & Technicoat Cond. Coil
HF Honeywell Excel 10 Controller, DFS, APS, Technicoat Cond. Coil, & Phase Monitor
HG Honeywell Excel 10 Controller, DFS, APS, Technicoat Cond. Coil, & Coil Guard
HH Honeywell Excel 10 Controller, DFS, APS, Technicoat Cond. Coil, Phase Monitor, & Coil Guard
HJ Honeywell Excel 10 Controller, DFS, APS & Technicoat Evap. Coil
HK Honeywell Excel 10 Controller, DFS, APS, Technicoat Evap. Coil, & Phase Monitor
HL Honeywell Excel 10 Controller, DFS, APS, Technicoat Evap. Coil, & Coil Guard
HM Honeywell Excel 10 Controller, DFS, APS, Technicoat Evap. Coil, Phase Monitor, & Coil Guard
HN Honeywell Excel 10 Controller, DFS, APS & Technicoat Evap. & Cond Coils
Unitary Products 9
HP Honeywell Excel 10 Controller, DFS, APS, Technicoat Evap. & Cond Coils, & Phase Monitor
HQ Honeywell Excel 10 Controller, DFS, APS, Technicoat Evap. & Cond Coils, & Coil Guard
HR Honeywell Excel 10 Controller, DFS, APS, Technicoat Evap. & Cond Coils, Phase Monitor, & Coil Guard
JA Johnson UNT Controller with Dirty Filter Switch & Air Proving Switch
JB Johnson UNT Controller, DFS, APS & Phase Monitor
JC Johnson UNT Controller, DFS, APS & Coil Guard
JD Johnson UNT Controller, DFS, APS, Phase Monitor, & Coil Guard
JE Johnson UNT Controller, DFS, APS & Technicoat Cond. Coil
JF Johnson UNT Controller, DFS, APS, Technicoat Cond. Coil, & Phase Monitor
JG Johnson UNT Controller, DFS, APS, Technicoat Cond. Coil, & Coil Guard
JH Johnson UNT Controller, DFS, APS, Technicoat Cond. Coil, Phase Monitor, & Coil Guard
JJ Johnson UNT Controller, DFS, APS & Technicoat Evap. Coil
JK Johnson UNT Controller, DFS, APS, Technicoat Evap. Coil, & Phase Monitor
JL Johnson UNT Controller, DFS, APS, Technicoat Evap. Coil, & Coil Guard
JM Johnson UNT Controller, DFS, APS, Technicoat Evap. Coil, Phase Monitor, & Coil Guard
JN Johnson UNT Controller, DFS, APS & Technicoat Evap. & Cond Coils
JP Johnson UNT Controller, DFS, APS, Technicoat Evap. & Cond Coils, & Phase Monitor
JQ Johnson UNT Controller, DFS, APS, Technicoat Evap. & Cond Coils, & Coil Guard
JR Johnson UNT Controller, DFS, APS, Technicoat Evap. & Cond Coils, Phase Monitor, & Coil Guard
NA Novar ETC-3 Controller with Dirty Filter Switch & Air Proving Switch
NB Novar ETC-3 Controller, DFS, APS & Phase Monitor
NC Novar ETC-3 Controller, DFS, APS & Coil Guard
ND Novar ETC-3 Controller, DFS, APS, Phase Monitor, & Coil Guard
NE Novar ETC-3 Controller, DFS, APS & Technicoat Cond. Coil
NF Novar ETC-3 Controller, DFS, APS, Technicoat Cond. Coil, & Phase Monitor
NG Novar ETC-3 Controller, DFS, APS, Technicoat Cond. Coil, & Coil Guard
NH Novar ETC-3 Controller, DFS, APS, Technicoat Cond. Coil, Phase Monitor, & Coil Guard
NJ Novar ETC-3 Controller, DFS, APS & Technicoat Evap. Coil
NK Novar ETC-3 Controller, DFS, APS, Technicoat Evap. Coil, & Phase Monitor
NL Novar ETC-3 Controller, DFS, APS, Technicoat Evap. Coil, & Coil Guard
NM Novar ETC-3 Controller, DFS, APS, Technicoat Evap. Coil, Phase Monitor, & Coil Guard
NN Novar ETC-3 Controller, DFS, APS & Technicoat Evap. & Cond Coils
NP Novar ETC-3 Controller, DFS, APS, Technicoat Evap. & Cond Coils, & Phase Monitor
NQ Novar ETC-3 Controller, DFS, APS, Technicoat Evap. & Cond Coils, & Coil Guard
NR Novar ETC-3 Controller, DFS, APS, Technicoat Evap. & Cond Coils, Phase Monitor, & Coil Guard
TA Technicoat Condenser Coil
TB Technicoat Condenser Coil & Phase Monitor
TC Technicoat Condenser Coil & Coil Guard
TD Technicoat Condenser Coil & Dirty Filter Switch
TE Technicoat Condenser Coil, Phase Monitor, & Coil Guard
TF Technicoat Condenser Coil, Phase Monitor, & Dirty Filter Switch
036-21044-003-A-0304
10 Unitary Products
036-21044-003-A-0304
TG Technicoat Condenser Coil, Coil Guard, & Dirty Filter Switch
TH Technicoat Condenser Coil, Phase Monitor, Coil Guard, & Dirty Filter Switch
TJ Technicoat Evaporator Coil
TK Technicoat Evaporator Coil & Phase Monitor
TL Technicoat Evaporator Coil & Coil Guard
TM Technicoat Evaporator Coil & Dirty Filter Switch
TN Technicoat Evaporator Coil, Phase Monitor, & Coil Guard
TP Technicoat Evaporator Coil, Phase Monitor, & Dirty Filter Switch
TQ Technicoat Evaporator Coil, Coil Guard, & Dirty Filter Switch
TR Technicoat Evaporator Coil, Phase Monitor, Coil Guard, & Dirty Filter Switch
TS Technicoat Evaporator & Condenser Coils
TT Technicoat Evaporator & Condenser Coils & Phase Monitor
TU Technicoat Evaporator & Condenser Coils & Coil Guard
TV Technicoat Evaporator & Condenser Coils & Dirty Filter Switch
TW Technicoat Evaporator & Condenser Coils, Phase Monitor, & Coil Guard
TX Technicoat Evaporator & Condenser Coils, Phase Monitor, & Dirty Filter Switch
TY Technicoat Evaporator & Condenser Coils, Coil Guard, & Dirty Filter Switch
TZ Technicoat Evaporator & Condenser Coils, Phase Monitor, Coil Guard, & Dirty Filter Switch
RC Coil Guard, Heavy Mil Clear Shipping Bag, Made in U.S.A. Flag Decal
Unitary Products 11
Loading...