YAMAHA YZF-R1P User Manual
OWNER’S MANUAL
YZF-R1P
YZF-R1PC
5PW-28199-10LIT-11626-15-47
EAU03438
EAU00002
1-
INTRODUCTION
Congratulations on your purchase of the Yamaha YZF-R1 / YZF-R1C. This model is
the result of Yamaha’s vast experience in the production of fine sporting, touring, and
pacesetting racing machines. It represents the high degree of craftsmanship and
reliability that have made Yamaha a leader in these fields.
This manual will give you an understanding of the operation, inspection, and basic
maintenance of this motorcycle. If you have any questions concerning the operation
or maintenance of your motorcycle, please consult a Yamaha dealer.
The design and manufacture of this Yamaha motorcycle fully comply with the emissions standards for clean air applicable at the date of manufacture. Yamaha has met
these standards without reducing the performance or economy of operation of the
motorcycle. To maintain these high standards, it is important that you and your
Yamaha dealer pay close attention to the recommended maintenance schedules and
operating instructions contained within this manual.
1-
IMPORTANT MANUAL INFORMATION
Particularly important information is distinguished in this manual by the following notations:
The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS
INVOLVED!
EAU00003
WARNING
CAUTION:
NOTE:
Failure to follow WARNING instructions could result in severe injury or death to the
motorcycle operator, a bystander or a person inspecting or repairing the motorcycle.
A CAUTION indicates special precautions that must be taken to avoid damage to the
motorcycle.
A NOTE provides key information to make procedures easier or clearer.
NOTE:
_
This manual should be considered a permanent part of this motorcycle and should remain
●
with it even if the motorcycle is subsequently sold.
Yamaha continually seeks advancements in product design and quality. Therefore, while
●
this manual contains the most current product information available at the time of printing,
there may be minor discrepancies between your motorcycle and this manual. If you have
any questions concerning this manual, please consult your Yamaha dealer.
_
IMPORTANT MANUAL INFORMATION
EW000000
WARNING
_
PLEASE READ THIS MANUAL AND THE “YOU AND YOUR MOTORCYCLE: RIDING
TIPS” BOOKLET CAREFULLY AND COMPLETELY BEFORE OPERATING THIS MOTORCYCLE. DO NOT ATTEMPT TO OPERATE THIS MOTORCYCLE UNTIL YOU HAVE ATTAINED ADEQUATE KNOWLEDGE OF ITS CONTROLS AND OPERATING FEATURES
AND UNTIL YOU HAVE BEEN TRAINED IN SAFE AND PROPER RIDING TECHNIQUES.
REGULAR INSPECTIONS AND CAREFUL MAINTENANCE, ALONG WITH GOOD RIDING
SKILLS, WILL ENSURE THAT YOU SAFELY ENJOY THE CAPABILITIES AND THE RELIABILITY OF THIS MOTORCYCLE.
_
IMPORTANT MANUAL INFORMATION
AFFIX DEALER
LABEL HERE
YZF-R1P/YZF-R1PC
OWNER’S MANUAL
©2001 by Yamaha Motor Corporation, U.S.A.
1st edition, November 2001
All rights reserved.
Any reprinting or unauthorized use
without the written permission of
Yamaha Motor Corporation, U.S.A.
is expressly prohibited.
Printed in Japan.
P/N LIT-11626-15-47
EAU04247
EAU00009
TABLE OF CONTENTS
1 SAFETY INFORMATION
2 DESCRIPTION
3 INSTRUMENT AND CONTROL FUNCTIONS
4 PRE-OPERATION CHECKS
5 OPERATION AND IMPORTANT RIDING POINTS
6 PERIODIC MAINTENANCE AND MINOR REPAIR
7 MOTORCYCLE CARE AND STORAGE
8 SPECIFICATIONS
9 CONSUMER INFORMATION
INDEX
1
2
3
4
5
6
7
8
9
SAFETY INFORMATION
Safe riding .......................................................................................... 1-1
Protective apparel .............................................................................. 1-3
Modifications ...................................................................................... 1-3
Loading and accessories ................................................................... 1-3
Gasoline and exhaust gas.................................................................. 1-5
Location of important labels .............................................................. 1-7
1
1-
SAFETY INFORMATION
EAU04193
MOTORCYCLES ARE SINGLE TRACK VEHICLES. THEIR SAFE USE AND OPERATION ARE DEPENDENT UPON THE USE OF PROPER RIDING TECHNIQUES AS WELL AS THE EXPERTISE OF
THE OPERATOR. EVERY OPERATOR SHOULD KNOW THE FOLLOWING REQUIREMENTS BE-
1
FORE RIDING THIS MOTORCYCLE.
HE OR SHE SHOULD:
1. OBTAIN THOROUGH INSTRUCTIONS FROM A COMPETENT SOURCE ON ALL ASPECTS OF
MOTORCYCLE OPERATION.
2. OBSERVE THE WARNINGS AND MAINTENANCE REQUIREMENTS IN THE OWNER’S
MANUAL.
3. OBTAIN QUALIFIED TRAINING IN SAFE AND PROPER RIDING TECHNIQUES.
4. OBTAIN PROFESSIONAL TECHNICAL SERVICE AS INDICATED BY THE OWNER’S MANUAL
AND/OR WHEN MADE NECESSARY BY MECHANICAL CONDITIONS.
Safe riding
1. Always make pre-operation checks. Careful checks may help prevent an accident.
2. This motorcycle is designed to carry the operator and a passenger.
3. The failure of motorists to detect and recognize motorcycles in traffic is the predominating cause of
automobile/motorcycle accidents. Many accidents have been caused by an automobile driver who
did not see the motorcycle. Making yourself conspicuous appears to be very effective in reducing the
chance of this type of accident.
Therefore:
a. Wear a brightly colored jacket.
b. Use extra caution when you are approaching and passing through intersections, since intersec-
tions are the most likely places for motorcycle accidents to occur.
c. Ride where other motorists can see you. Avoid riding in another motorist’s blind spot.
1-1
SAFETY INFORMATION
4. Many accidents involve inexperienced operators. In fact, many operators who have been involved in
accidents do not even have a current motorcycle license.
a. Make sure that you are qualified and that you only lend your motorcycle to other qualified opera-
tors.
b. Know your skills and limits. Staying within your limits may help you to avoid an accident.
c. We recommend that you practice riding your motorcycle where there is no traffic until you have
become thoroughly familiar with the motorcycle and all of its controls.
5. Many accidents have been caused by error of the motorcycle operator. A typical error made by the
operator is veering wide on a turn due to EXCESSIVE SPEED or undercornering (insufficient lean
angle for the speed).
a. Always obey the speed limit and never travel faster than warranted by road and traffic conditions.
b. Always signal before turning or changing lanes. Make sure that other motorists can see you.
6. The posture of the operator and passenger is important for proper control.
a. The operator should keep both hands on the handlebar and both feet on the operator footrests
during operation to maintain control of the motorcycle.
b. The passenger should always hold onto the operator, the seat strap or grab bar, if equipped, with
both hands and keep both feet on the passenger footrests.
c. Never carry a passenger unless he or she can firmly place both feet on the passenger footrests.
7. Never ride under the influence of alcohol or other drugs.
8. This motorcycle is designed for on-road use only. It is not suitable for off-road use.
1
1-2
SAFETY INFORMATION
Protective apparel
The majority of fatalities from motorcycle accidents are the result of head injuries. The use of a safety
1
helmet is the single most critical factor in the prevention or reduction of head injuries.
1. Always wear an approved helmet.
2. Wear a face shield or goggles. Wind in your unprotected eyes could contribute to an impairment of vision that could delay seeing a hazard.
3. The use of a jacket, heavy boots, trousers, gloves, etc., is effective in preventing or reducing abrasions or lacerations.
4. Never wear loose-fitting clothes, otherwise they could catch on the control levers, footrests, or wheels
and cause injury or an accident.
5. Never touch the engine or exhaust system during or after operation. They become very hot and can
cause burns. Always wear protective clothing that covers your legs, ankles, and feet.
6. A passenger should also observe the above precautions.
Modifications
Modifications made to this motorcycle not approved by Yamaha, or the removal of original equipment,
may render the motorcycle unsafe for use and may cause severe personal injury. Modifications may also
make your motorcycle illegal to use.
Loading and accessories
Adding accessories or cargo to your motorcycle can adversely affect stability and handling if the weight
distribution of the motorcycle is changed. To avoid the possibility of an accident, use extreme caution
when adding cargo or accessories to your motorcycle. Use extra care when riding a motorcycle that has
added cargo or accessories. Here are some general guidelines to follow if loading cargo or adding accessories to your motorcycle:
1-3
SAFETY INFORMATION
Loading
The total weight of the operator, passenger, accessories and cargo must not exceed the maximum load
limit of YZF-R1: 202 kg (445 lb)/YZF-R1C: 201 kg (443 lb). When loading within this weight limit, keep
the following in mind:
1. Cargo and accessory weight should be kept as low and close to the motorcycle as possible. Make
sure to distribute the weight as evenly as possible on both sides of the motorcycle to minimize imbalance or instability.
2. Shifting weights can create a sudden imbalance. Make sure that accessories and cargo are securely
attached to the motorcycle before riding. Check accessory mounts and cargo restraints frequently.
3. Never attach any large or heavy items to the handlebar, front fork, or front fender. These items, including such cargo as sleeping bags, duffel bags, or tents, can create unstable handling or a slow
steering response.
Accessories
Genuine Yamaha accessories have been specifically designed for use on this motorcycle. Since
Yamaha cannot test all other accessories that may be available, you must personally be responsible for
the proper selection, installation and use of non-Yamaha accessories. Use extreme caution when selecting and installing any accessories.
Keep the following guidelines in mind, as well as those provided under “Loading” when mounting accessories.
1. Never install accessories or carry cargo that would impair the performance of your motorcycle. Carefully inspect the accessory before using it to make sure that it does not in any way reduce ground
clearance or cornering clearance, limit suspension travel, steering travel or control operation, or obscure lights or reflectors.
1
1-4
SAFETY INFORMATION
a. Accessories fitted to the handlebar or the front fork area can create instability due to improper
weight distribution or aerodynamic changes. If accessories are added to the handlebar or front
fork area, they must be as lightweight as possible and should be kept to a minimum.
1
b. Bulky or large accessories may seriously affect the stability of the motorcycle due to aerodynamic
effects. Wind may attempt to lift the motorcycle, or the motorcycle may become unstable in cross
winds. These accessories may also cause instability when passing or being passed by large vehicles.
c. Certain accessories can displace the operator from his or her normal riding position. This improp-
er position limits the freedom of movement of the operator and may limit control ability, therefore,
such accessories are not recommended.
2. Use caution when adding electrical accessories. If electrical accessories exceed the capacity of the
motorcycle’s electrical system an electric failure could result, which could cause a dangerous loss of
lights or engine power.
Gasoline and exhaust gas
1. GASOLINE IS HIGHLY FLAMMABLE:
a. Always turn the engine off when refueling.
b. Take care not to spill any gasoline on the engine or exhaust system when refueling.
c. Never refuel while smoking or in the vicinity of an open flame.
2. Never start the engine or let it run for any length of time in a closed area. The exhaust fumes are poisonous and may cause loss of consciousness and death within a short time. Always operate your
motorcycle in an area that has adequate ventilation.
3. Always turn the engine off before leaving the motorcycle unattended and remove the key from the
main switch. When parking the motorcycle, note the following:
1-5
SAFETY INFORMATION
a. The engine and exhaust system may be hot, therefore, park the motorcycle in a place where pe-
destrians or children are not likely to touch these hot areas.
b. Do not park the motorcycle on a slope or soft ground, otherwise it may fall over.
c. Do not park the motorcycle near a flammable source, (e.g., a kerosene heater, or near an open
flame), otherwise it could catch fire.
4. When transporting the motorcycle in another vehicle, make sure that it is kept upright. If the motorcycle should lean over, gasoline may leak out of the fuel tank.
5. If you should swallow any gasoline, inhale a lot of gasoline vapor, or allow gasoline to get into your
eyes, see your doctor immediately. If any gasoline spills on your skin or clothing, immediately wash
the affected area with soap and water and change your clothes.
1
1-6
SAFETY INFORMATION
Location of important labels
Please read the following important labels carefully before operating this motorcycle.
1
EAU02977
1-7
SAFETY INFORMATION
1 California only6
CAUTION
Cleaning with alkaline or
acid cleaner, gasoline or
solvent will damage
windshield.
Use neutral detergent.
5LV-2835Y-00
2
PREMIUM UNLEADED GASOLINE ONLY
91 Min. Pump Octane (R+M) 2
5PW-2415E-10
3
4
1
7
5
1-8
SAFETY INFORMATION
8
1
9
10
1-9
DESCRIPTION
Left view ............................................................................................. 2-1
Right view........................................................................................... 2-2
Controls and instruments ................................................................... 2-3
2
2-
DESCRIPTION
Left view
2
1. Fuse box (page 6-40)
2. Front fork compression damping force adjusting screw (page 3-19)
3. Front fork rebound damping force adjusting screw (page 3-19)
4. Front fork spring preload adjusting bolt (page 3-18)
5. Front brake fluid reservoir (page 6-31)
6. Shock absorber assembly spring preload adjusting ring (page 3-20)
7. Shock absorber assembly compression damping force adjusting screw (page 3-21)
8. Owner’s tool kit (page 6-1)
9. Shock absorber assembly rebound damping force adjusting screw (page 3-21)
10. Engine oil drain bolt (page 6-14)
11. Engine oil filter cartridge (page 6-15)
EAU00026
2-1
Right view
DESCRIPTION
2
12. Luggage strap holders (page 3-23)
13. Helmet holders (page 3-17)
14. Main fuse (page 6-40)
15. Electronic fuel injection fuse (page 6-40)
16. Battery (page 6-39)
17. Rear brake fluid reservoir (page 6-32)
18. Air filter element (page 6-21)
19. Radiator cap (page 6-18)
20. Coolant reservoir (page 6-18)
21. Engine oil level check window (page 6-14)
22. Engine oil filler cap (page 6-14)
2-2
DESCRIPTION
Controls and instruments
2
1. Clutch lever (page 3-12)
2. Left handlebar switches (page 3-11)
3. Multi-function display (page 3-6)
4. Main switch/steering lock (page 3-1)
5. Tachometer (page 3-11)
6. Right handlebar switches (page 3-12)
7. Throttle grip (page 6-23)
8. Brake lever (page 3-13)
2-3
INSTRUMENT AND CONTROL FUNCTIONS
Main switch/steering lock ..................................... 3-1
Indicator and warning lights ................................ 3-2
Multi-function display ...........................................3-6
Tachometer ........................................................3-11
Handlebar switches ...........................................3-11
Clutch lever ........................................................3-12
Shift pedal ..........................................................3-12
Brake lever ......................................................... 3-13
Brake pedal ........................................................3-13
Fuel tank cap .....................................................3-13
Fuel .................................................................... 3-14
Catalytic converter ............................................ 3-15
Seats ................................................................. 3-15
Helmet holders .................................................. 3-17
Storage compartment ....................................... 3-17
Adjusting the front fork ...................................... 3-18
Adjusting the shock absorber assembly ............ 3-20
Luggage strap holders ...................................... 3-23
EXUP system .................................................... 3-23
Sidestand .......................................................... 3-23
Ignition circuit cut-off system ............................. 3-24
3
3-
INSTRUMENT AND CONTROL FUNCTIONS
ON
All electrical circuits are supplied with
power, and the meter lighting, taillight,
license plate light, auxiliary lights and
position lights come on, and the engine
can be started. The key cannot be re-
3
EAU00029
Main switch/steering lock
The main switch/steering lock controls
the ignition and lighting systems, and is
moved.
NOTE:
_
The headlights come on automatically
when the engine is started and stay on
until the key is turned to “OFF”, even if
the engine stalls.
_
used to lock the steering. The various
positions are described below.
OFF
All electrical systems are off. The key
can be removed.
EAU00027
EAU04565
EAU00040
LOCK
The steering is locked, and all electrical
systems are off. The key can be removed.
EAU00038
To lock the steering
1. Turn the handlebars all the way to
the left.
2. Push the key in from the “OFF” position, and then turn it to “LOCK”
while still pushing it.
3. Remove the key.
3-1
To unlock the steering
Push the key in, and then turn it to
“OFF” while still pushing it.
1. Push.
2. Turn.
EW000016
WARNING
_
Never turn the key to “OFF” or
“LOCK” while the motorcycle is
moving, otherwise the electrical
systems will be switched off, which
may result in loss of control or an
accident. Make sure that the motorcycle is stopped before turning the
key to “OFF” or “LOCK”.
_
INSTRUMENT AND CONTROL FUNCTIONS
Fuel level warning light “ ”
This warning light comes on when the
fuel level drops below approximately
3.3 L (0.73 lmp gal, 0.87 US gal). When
this occurs, refuel as soon as possible.
The electrical circuit of the warning light
can be checked according to the following procedure.
1. Right turn signal indicator light “ ”
2. Fuel level warning light “ ”
3. Oil level warning light “ ”
4. Neutral indicator light “ ”
5. Engine trouble warning light “ ”
6. High beam indicator light “ ”
7. Left turn signal indicator light “ ”
EAU03034
Indicator and warning lights
EAU04121
Turn signal indicator lights “ ”
and “ ”
The corresponding indicator light flashes when the turn signal switch is
pushed to the left or right.
1. Turn the key to “ON”.
2. If the warning light does not come
on for a few seconds, then go off,
have a Yamaha dealer check the
electrical circuit.
EAU04303
3
3-2
INSTRUMENT AND CONTROL FUNCTIONS
3
1. Right turn signal indicator light “ ”
2. Fuel level warning light “ ”
3. Oil level warning light “ ”
4. Neutral indicator light “ ”
5. Engine trouble warning light “ ”
6. High beam indicator light “ ”
7. Left turn signal indicator light “ ”
Oil level warning light “ ”
This warning light comes on when the
engine oil level is low.
The electrical circuit of the warning light
can be checked according to the following procedure.
1. Turn the key to “ON”.
2. If the warning light does not come
on for a few seconds, then go off,
have a Yamaha dealer check the
electrical circuit.
EAU04301
NOTE:
_
Even if the oil level is sufficient, the
warning light may flicker when riding on
a slope or during sudden acceleration
or deceleration, but this is not a malfunction.
_
EAU00061
Neutral indicator light “ ”
This indicator light comes on when the
transmission is in the neutral position.
EAU04514
Engine trouble warning light “ ”
This warning light comes on or flashes
when an electrical circuit monitoring
the engine is defective. When this occurs, have a Yamaha dealer check the
self-diagnosis system.
NOTE:
_
This warning light comes on for a few
seconds, then goes off when the key is
turned to “ON”, but this does not indicate a malfunction.
_
EAU00063
High beam indicator light “ ”
This indicator light comes on when the
high beam of the headlight is switched
on.
3-3
1. Engine speed indicator light
2. Coolant temperature warning light “ ”
3. Coolant temperature display
EAU04559
Engine speed indicator light
The electrical circuit of the indicator
light can be checked according to the
following procedure.
1. Turn the key to “ON”.
2. If the indicator light does not come
on for a few seconds, then go off,
have a Yamaha dealer check the
electrical circuit. (See pages 3-8–
3-10 for a detailed explanation of
the function of this indicator light
and on how to set it.)
INSTRUMENT AND CONTROL FUNCTIONS
EAU04515*
Coolant temperature warning light
“”
This warning light comes on when the
engine overheats. When this occurs,
stop the engine immediately and allow
the engine to cool.
The electrical circuit of the warning light
can be checked according to the following procedure.
1. Turn the key to “ON”.
2. If the warning light does not come
on for a few seconds, then go off,
have a Yamaha dealer check the
electrical circuit.
CAUTION:
_
Do not operate the engine if it is
overheated.
_
EC000002
3
3-4
INSTRUMENT AND CONTROL FUNCTIONS
CB-25E
Coolant
temperature
0–39 °C
(0–103 °F)
Display Conditions What to do
Message “LO” is
displayed.
OK. Go ahead with riding.
3
40–116 °C
(104–242 °F)
117–139 °C
(243–283 °F)
Above 140 °C
(284 °F)
Temperature is
displayed.
Temperature flashes.
Warning light comes on.
Message “HI” flashes.
Warning light comes on.
OK. Go ahead with riding.
Stop the motorcycle and allow it to
idle until the coolant temperature
goes down.
If the temperature does not go
down, stop the engine. (See the
“Engine overheating” section on
page 6-51 for further instructions.)
Stop the engine and allow it to cool.
(See the “Engine overheating” section on page 6-51 for further instructions.)
3-5
INSTRUMENT AND CONTROL FUNCTIONS
1. Multi-function display
2. “SELECT” button
3. “RESET” button
EAU04566
Multi-function display
The multi-function display is equipped
with the following:
a speedometer (which shows the
●
riding speed)
an odometer (which shows the to-
●
tal distance traveled)
two tripmeters (which show the
●
distance traveled since they were
last set to zero)
a fuel reserve tripmeter (which
●
shows the distance traveled since
the fuel level warning light came
on)
a clock
●
a self-diagnosis device
●
a display brightness and engine
●
speed indicator light control mode
NOTE:
_
Be sure to turn the key to “ON” be-
●
fore using the “SELECT” and
“RESET” buttons.
To switch the speedometer and
●
odometer/tripmeter displays between kilometers and miles, press
the “SELECT” button and
“RESET” button together for at
least two seconds.
_
Odometer and tripmeter modes
Pushing the “SELECT” button switches
the display between the odometer
mode “ODO” and the tripmeter modes
“TRIP 1” and “TRIP 2” in the following
order:
ODO→ TRIP 1 → TRIP 2 → ODO
If the fuel level warning light comes on
(see page 3-2), the odometer display
will automatically change to the fuel reserve tripmeter mode “F-TRIP” and
start counting the distance traveled
from that point. In that case, pushing
the “SELECT” button switches the display between the various tripmeter and
odometer modes in the following order:
F-TRIP→ TRIP 1 → TRIP 2 → ODO
F-TRIP
→
3
3-6
Loading...