Yamaha T9.9HP, F9.9HP User Manual
OWNER’S MANUAL
F9.9C
T9.9C
U.S.A.Edition
LIT-18626-05-49
EMU14490
E
TO THE OWNER
Thank you for choosing a Yamaha outboard
motor. This Owner’s manual contains information needed for proper operation, maintenance and care. A thorough understanding of these simple instructions will help you
obtain maximum enjoyment from your new
Yamaha. If you have any question about the
operation or maintenance of your outboard
motor, please consult a Yamaha dealer.
In this Owner’s Manual particularly important information is distinguished in the following ways.
Q The Safety Alert Symbol means
ATTENTION! BECOME ALERT!
YOUR SAFETY IS INVOLVED!
w
Failure to follow WARNING instructions
could result in severe injury or death to
the machine operator, a bystander, or a
person inspecting or repairing the outboard motor.
cC
A CAUTION indicates special precautions that must be taken to avoid damage to the outboard motor.
NOTE:
A NOTE provides key information to make
procedures easier or clearer.
* Yamaha continually seeks advancements
in product design and quality. Therefore,
while this manual contains the most current product information available at the
time of printing, there may be minor discrepancies between your machine and
this manual. If there is any question concerning this manual, please consult your
Yamaha dealer.
NOTE:
The F9.9MH, T9.9ER, and their standard
accessories are used as a base for the
explanations and illustrations in this manual. Therefore, some items may not apply to
every model.
EMU14460
F9.9C, T9.9C
OWNER'S MANUAL
©2003 by Yamaha Motor Corporation, USA
1st Edition, April 2003
All rights reserved.
Any reprinting or unauthorized use
without the written permission of
Yamaha Motor Corporation, USA
is expressly prohibited.
Printed in Japan
P/N LIT-18626-05-49
EMU00030
E
CONTENTS
GENERAL INFORMATION
BASIC COMPONENTS
OPERATION
MAINTENANCE
1
2
3
4
TROUBLE RECOVERY
INDEX
READ THIS OWNER’S MANUAL CAREFULLY
BEFORE OPERATING YOUR OUTBOARD MOTOR.
5
6
E
EMU00040
Chapter 1
GENERAL
INFORMATION
IDENTIFICATION NUMBERS RECORD 1-1
Outboard motor serial number..............1-1
Key number ..........................................1-1
EMISSION CONTROL INFORMATION ..1-2
Star labels.............................................1-3
SAFETY INFORMATION ........................1-4
IMPORTANT LABELS............................1-6
BASIC BOATING RULES ......................1-7
FUELING INSTRUCTIONS ...................1-11
Gasoline..............................................1-12
ENGINE OIL..........................................1-13
1
2
3
BATTERY REQUIREMENT ..................1-14
PROPELLER SELECTION ...................1-15
START-IN-GEAR PROTECTION..........1-16
4
5
6
E
YAMAHA MOTOR CO., LTD.
MADE IN JAPAN
PAYS D'ORIGINE JAPON
1
401012
000319
123
YAMAHA
q
EMU00050
IDENTIFICATION NUMBERS
RECORD
EMU00070
OUTBOARD MOTOR SERIAL NUMBER
The outboard motor serial number is
stamped on the label attached to the port
side of the clamp-bracket.
Record your outboard motor serial number
in the spaces provided to assist you in
ordering spare parts from your Yamaha
dealer or for reference in case your outboard motor is stolen.
1 Outboard motor serial number
1-1
EMU00080
KEY NUMBER
If a main key switch is equipped with the
motor, the key identification number is
stamped on your key as shown in the illustration. Record this number in the space
provided for reference in case you need a
new key.
1 Key number
q
w
001537
E
EMU13850
EMISSION CONTROL
INFORMATION
EMU14440
NORTH AMERICAN MODELS
This engine conforms to U.S.
Environmental Protection Agency (EPA)
regulations for marine SI engines. See the
label affixed to your engine for details.
q
EMISSION CONTROL INFORMATION
ENGINE FAMILY :
THIS ENGINE CONFORMS TO 2001 U.S. EPA REGULATIONS FOR MARINE SI ENGINES.
THIS ENGINE CONFORMS TO 2001 CALIFORNIA EMISSION REGULATIONS FOR SI MARINE ENGINES.
REFER TO THE OWNERS MANUAL FOR MAINTENANCE SPECIFICATIONS AND ADJUSTMENTS.
g/kw-hr
FELs :
SPARK PLUG :
DISPLACEMENT :
ADVERTISED POWER :
IDLE SPEED :
SPARK PLUG GAP (mm) :
3
cm
FUEL : GASOLINE
VALVE LASH (mm) :
kw
rpm IN NEUTRAL
IN EX
Approval label of Emission control certificate
EM
This label is attached to the bottom cowling.
1 Emission control information label
New Technology ; (4-stroke/HPDI) EM
Manufactured date label
This label is attached to the clamp bracket.
w
2 Manufactured date label
Manufactured:
1-2
E
000852
q
EMU13890
STAR LABELS
Your outboard motor is labeled with a
California Air Resources Board (CARB) star
label. See below for a description of your
particular label.
1 Star label
One Star - Low Emission
The one-star label identifies engines that
meet the Air Resources Board’s 2001
exhaust emission standards. Engines meeting these standards have 75% lower emissions than conventional carbureted twostroke engines. These engines are
equivalent to the U.S. EPA’s 2006 standards for marine engines.
Two Stars - Very Low Emission
The two-star label identifies engines that
meet the Air Resources Board’s 2004
exhaust emission standards. Engines meeting these standards have 20% lower emissions than One Star-Low-Emission engines.
1-3
Three Stars - Ultra Low Emission
The three-star label identifies engines that
meet the Air Resources Board’s 2008
exhaust emission standards. Engines meeting these standards have 65% lower emissions than One Star-Low-Emission engines.
E
EMU09170
QSAFETY INFORMATION
8 Before mounting or operating the out-
board motor, read this entire manual.
Reading it should give you an understanding of the motor and its operation.
8 Before operating the boat, read any
owner’s or operator’s manuals supplied
with it and all labels. Be sure you understand each item before operating.
8 Do not overpower the boat with this out-
board motor. Overpowering the boat
could result in loss of control. The rated
power of the outboard should be equal to
or less than the rated horsepower capacity of the boat. If the rated horsepower
capacity of the boat is unknown, consult
the dealer or boat manufacturer.
8 Do not modify the outboard. Modifications
could make the motor unfit or unsafe to
use.
8 Never operate after drinking alcohol or
taking drugs. About 50% of all boating
fatalities involve intoxication.
8 Have an approved personal flotation
device (PFD) on board for every occupant. It is a good idea to wear a PFD
whenever boating. At a minimum, children
and non-swimmers should always wear
PFDs, and everyone should wear PFDs
when there are potentially hazardous
boating conditions.
8 Gasoline is highly flammable, and its
vapors are flammable and explosive.
Handle and store gasoline carefully. Make
sure there are no gas fumes or leaking
fuel before starting the engine.
8 This product emits exhaust gases which
contain carbon monoxide, a colorless,
odorless gas which may cause brain
damage or death when inhaled.
Symptoms include nausea, dizziness,
and drowsiness. Keep cockpit and cabin
areas well ventilated. Avoid blocking
exhaust outlets.
8 Check throttle, shift, and steering for
proper operation before starting the
engine.
8 Attach the engine stop switch lanyard to a
secure place on your clothing, or your
arm or leg while operating. If you accidentally leave the helm, the lanyard will pull
from the switch, stopping the engine.
8 Know the marine laws and regulations
where you will be boating - and obey
them. Refer to the “RULES OF THE
ROAD” section for basic boating rules.
8 Stay informed about the weather. Check
weather forecasts before boating. Avoid
boating in hazardous weather.
8 Tell someone where you are going: leave
a Float Plan with a responsible person.
Be sure to cancel the Float Plan when
you return.
8 Use common sense and good judgment
when boating. Know your abilities, and be
sure you understand how your boat handles under the different boating conditions
you may encounter. Operate within your
limits, and the limits of your boat. Always
operate at safe speeds, and keep a careful watch for obstacles and other traffic.
8 Always watch carefully for swimmers dur-
ing the engine operation.
8 Stay away from swimming areas.
8 When a swimmer is in the water near you
shift into neutral and shut off the engine.
1-4
8 Be informed about boating safety.
Additional publications and information
can be obtained from many organizations, including the following:
United States Coast Guard
Consumer Affairs Staff (G-BC)
Office of Boating, Public, and Consumer
Affairs
U.S. Coast Guard Headquarters
Washington, D.C. 20593-0001
Boating Safety Hotline: 1-800-368-5647
National Marine Manufacturers
Association (NMMA)
401 N. Michigan Ave.
Chicago, Il 60611
Marine Retailers Association of America
155 N. Michigan Ave.
Chicago, Il 60601
E
1-5
E
w
q
e
q
This engine is equipped with a neutral starting device.
The engine will not start unless the shift control is
in neutral position.
w
WARNING
001519
6E0-83627-41
EMU00140
IMPORTANT LABELS
WARNING LABELS
7Be sure shift control is in neutral
before starting engine. (except 2HP)
7Do not touch or remove electrical parts
when starting or during operation.
7Keep hands,hair,and clothes away from flywheel
and other rotating parts while engine is running.
6A1-83625-41
e
WARNING
Transport and store the engine only as shown.
Otherwise, engine damage could result from
leaking oil.
CAUTION
6G8-13444-41
CAUTION LABELS
1-6
E
EMU00150
BASIC BOATING RULES
(Rules of the road)
Just as there are rules which apply when
you are driving on streets and high ways,
there are waterway rules which apply when
you are driving your boat. These rules are
used internationally, and are also enforced
by the United States Coast Guard and local
agencies. You should be aware of these
rules, and follow them whenever you
encounter another vessel on the water.
Several sets of rules prevail according to
geographic location, but are all basically the
same as the International Rules of the
Road. The rules presented here in your
Owner’s Manual are condensed, and have
been provided for your convenience only.
Consult your local U.S. Coast Guard
Auxiliary or Department of Motor Vehicles
for a complete set of rules governing the
waters in which you will be using your boat.
STEERING AND SAILING RULES
AND SOUND SIGNALS
Whenever two vessels on the water meet
one another, one vessel has the right-ofway; it is called the “stand-on” vessel. The
vessel which does not have the right-of-way
is called the “give-way” or “burdened” vessel. These rules determine which vessel
has the right-of-way, and what each vessel
should do.
Stand-on vessel
The vessel with the right-of-way has the
duty to continue its course and speed,
except to avoid an immediate collision.
When you maintain your direction and
speed, the other vessel will be able to
determine how best to avoid you.
Give-way vessel
The vessel which does not have the rightof-way has the duty to take positive and
timely action to stay out of the way of the
Stand-On vessel. Normally, you should not
cross in front of the vessel with the right-ofway. You should slow down or change
directions briefly and pass behind the other
vessel. You should always move in such a
way that the operator of the other vessel
can see what you are doing.
“The general prudential rule”
This rule is called Rule 2 in the International
Rules and says,
‘In obeying and construing these rules due
regard shall be had to all dangers of navigation and collision, and to any special circumstances, which may render a departure
from the above rules necessary in order to
avoid immediate danger.’
In other words, follow the standard rules
except when a collision will occur unless
both vessels try to avoid each other. If that
is the case, both vessels become “GiveWay” vessels.
1-7
E
102045
RULES WHEN ENCOUNTERING
VESSELS
There are three main situations which you
may encounter with other vessels which
could lead to a collision unless the Steering
Rules are followed:
Meeting (you are approaching another vessel head-on)
Crossing (you are traveling across the
other vessel’s path)
Overtaking (you are passing or being
passed by another vessel)
In the following illustration, your boat is in
the center. You should give the right-of-way
to any vessels shown in white area (you are
the Give-Way vessel). Any vessels in the
shaded area must yield to you (they are the
Give-Way vessels). Both you and the meeting vessel must alter course to avoid each
other.
one another if you continue on your set
course and speed.
102044
Crossing
When two power driven vessels are crossing each other’s path close enough to run
the risk of collision, the vessel which has
the other on the starboard (right) side must
keep out of the way of the other. If the other
vessel is on your right, you must keep out of
its way; you are the Give-Way vessel. If the
other vessel is on your port (left) side,
remember that you should maintain course
and direction, provided the other vessel
gives you the right-of-way as it should.
Meeting
If you are meeting another power vessel
head on, and are close enough to run the
risk of collision, neither of you has the rightof-way! Both of you should alter course to
avoid an accident. You should keep the
other vessel on your port (left) side. This
rule doesn’t apply if both of you will clear
102046
Overtaking
If you are passing another vessel, you are
the “Give-Way” vessel. This means that the
other vessel is expected to maintain its
course and speed. You must stay out of its
1-8
E
way until you are clear of it. Likewise, if
another vessel is passing you, you should
maintain your speed and direction so that
the other vessel can steer itself around you.
OTHER SPECIAL SITUATIONS
There are three other rules you should be
aware of when driving your boat around
other vessels.
Narrow channels and bends
When navigating in narrow channels, you
should keep to the right when it is safe and
practical to do so. If the operator of a
power-driven vessel is preparing to go
around a bend that may obstruct the view of
other water vessels, the operator should
sound a prolonged blast on the whistle (4 to
6 seconds). If another vessel is around the
bend, it too should sound the whistle. Even
if no reply is heard, however, the vessel
should still proceed around the bend with
caution. If you navigate such waters with
your boat, you will need to carry a portable
air horn, available from local marine supply
stores.
Fishing vessel right-of-way
All vessels which are fishing with nets, lines
or trawls are considered to be “fishing vessels” under the International Rules. Vessels
with trolling lines are not considered fishing
vessels. Fishing vessels have the right-ofway regardless of position. Fishing vessels
cannot, however, impede the passage of
other vessels in narrow channels.
Sailing vessel right-of-way
Sailing vessels should normally be given
the right-of-way. The exceptions to this are:
1. When the sailing vessel is overtaking
the power-driven vessel, the power-driven vessel has the right-of-way.
2. Sailing vessels should keep clear of
any fishing vessel.
3. In a narrow channel, a sailing vessel
should not hamper the safe passage of
a power-driven vessel which can navigate only in such a channel.
Reading buoys and other markers
The waters of the United states are marked
for safe navigation by the lateral system of
buoyage. Simply put, buoys and markers
have an arrangement of shapes, colors,
numbers and lights to show which side of
the buoy a boater should pass on when
navigating in a particular direction. The
markings on these buoys are oriented from
the perspective of being entered from seaward (the boater is going towards the port).
This means that red buoys are passed on
the starboard (right) side when proceeding
from open water into port, and black buoys
are to port (left) side. When navigating out
of port, your position with respect to the
buoys should be reversed; red buoys
should be to port and black buoys to starboard.
Many bodies of water used by boaters are
entirely within the boundaries of a particular
state. The Uniform State Waterway Marking
System has been devised for these waters.
This system uses buoys and signs with distinctive shapes and colors to show regulatory or advisory information. These markers
are white with black letters and orange
boarders. They signify speed zones,
restricted areas, danger areas, and general
information.
1-9
Remember, markings may vary by geo-
1
1
A
1
1
Proceeding toward head
of navigation from seaward
CAN BUOY
Odd number. Leave to port.
OR
SECONDARY CHANNEL BUOYS
STARTS NEW NUMBERING SYSTEM
old new
C " 1
"
NUN BUOY
Even number. Leave to starboard
N
"
2
"
No change
BUOY
COLOR CODE
BLACK
RED
GREEN
"
A
"
"
2
"
"
1
"
"
3
"
"
4
"
"
5
"
"
7
"
N
"
2
"
"
6
"
C
"
1
"
RB
"
L
"
RG
"
L
"
or
SECONDARY CHANNEL
MAIN CHANNEL
old
new
2
2
2
A
L
L
Odd number. increasing toward head of naviga-
MAIN CHANNEL BUOYS
"
1
" "
3
" "
5
" "
7
"
tion.Leave to port (left) proceeding upstream.
LIGHTED BUOY (Port Hand)`
White Light
Green Light
old
new
old
new
old
new
LIGHTED BUOY (Starboard Hand)`
"
2
" "
4
" "
6
"
Even number,increasing toward head of navigation. Leave to starboard (right) proceeding upstream.
White Light Red Light
"
A
"
LIGHTED SAFE WATER BUOY
No number. Marks midchannel, pass on either
side. Letter has no lateral significance, used for
No number. Topmost band red
-
preferred
Top Mark
White Light
White Light
OR
OR
LIGHTED PREFERRED CHANNEL TO
RB
"
L
"
RG
"
L
"
PORT BUOY
identification and location purposes.
channel is to left of buoy. Letter has no lateral
significance, used for identification and location
purposes.
Red Light
Red or
White Light
OR
102052
graphic location. Always consult local boating authorities before driving your boat in
unfamiliar waters.
E
1-10
E
EMU00160
FUELING INSTRUCTIONS
w
GASOLINE AND ITS VAPORS ARE HIGHLY FLAMMABLE AND EXPLOSIVE!
8 Do not smoke when refueling, and
keep away from sparks, flames, or
other sources of ignition.
8 Stop engine before refueling.
8 Refuel in a well-ventilated area. Refuel
portable fuel tanks off the boat.
8 Take care not to spill gasoline. If gaso-
line spills, wipe it up immediately with
dry rags.
8 Do not overfill the fuel tank.
8 Tighten the filler cap securely after
refueling.
8 If you should swallow some gasoline
inhale a lot of gasoline vapor, or get
gasoline in your eyes, get immediate
medical attention.
8 If any gasoline spills onto your skin,
immediately wash with soap and
water. Change clothing if gasoline
spills on it.
8 Touch the fuel nozzle to the filler open-
ing or funnel to help prevent electrostatic sparks.
1-11
cC
Use only new clean gasoline which has
been stored in clean containers and is
not contaminated with water or foreign
matter.
E
EMU18040
GASOLINE
Recommended gasoline:
Regular unleaded gasoline with a
minimum octane rating of 86 (Pump
Octane Number) = (R+M)/2
If knocking or pinging occurs, use a different brand of gasoline or premium unleaded
fuel.
EMU00270
Gasohol
There are two types of gasohol: gasohol
containing ethanol and that containing
methanol. Gasohol containing ethanol can
be used if ethanol content does not exceed
10% and the fuel meets minimum octane
ratings. Gasohol containing methanol is not
recommended by Yamaha because it can
cause fuel system damage or engine performance problems.
1-12
E
EMU17690
ENGINE OIL
Recommended engine oil:
4-stroke motor oil with a combination of corresponding SAE and API as shown in the
chart.
SAE API
SE
SF
SG
SH
10W-30
10W-40
Engine oil quantity:
See Chapter 4, “Specifications.”
SJ
cC
All 4-stroke engines are shipped from
the factory without engine oil.
1-13
001162
E
EMU17750
BATTERY REQUIREMENT
cC
Do not use a battery that does not meet
the specified capacity. If a battery which
does not meet specifications is used, the
electric system could perform poorly or
be overloaded, causing electric system
damage.
For electric start models, choose a battery
which meets the following specifications.
EMU18590
Minimum cold cranking amps
(CCA/SAE):245 amps at -18°C (-0.4°F)
Minimum marine cranking amps
(MCA/ABYC):323 amps at 0°C (32°F)
Minimum reserve capacity (RC/SAE):
52 minutes
EMU17830¯
cC
A battery cannot be connected to models that do not have a rectifier or
Rectifier Regulator.
Models without a rectifier or Rectifier
Regulator: F9.9MH
8 If you wish to use a battery with the
above models, install an optional
Rectifier Regulator.
1-14
E
EMU13950
PROPELLER SELECTION
The performance of your outboard motor
will be critically affected by your choice of
propeller, as an incorrect choice could
adversely affect performance and could
also seriously damage the motor. Engine
speed depends on the propeller size and
boat load. If engine speed is too high or too
low for good engine performance, this will
have an adverse effect on the engine.
Yamaha outboard motors are fitted with propellers chosen to perform well over a range
of applications, but there may be uses
where a propeller with a different pitch
would be more appropriate. For a greater
operating load, a smaller-pitch propeller is
more suitable as it enables the correct
engine speed to be maintained. Conversely,
a larger-pitch propeller is more suitable for
a smaller operating load.
1-15
Yamaha dealers stock a range of propellers, and can advise you and install a
propeller on your outboard that is best suited to your application.
NOTE:
At full throttle and under a maximum boat
load, the engine’s rpm should be within the
upper half of the full throttle operating
range, as listed in “SPECIFICATIONS” on
page 4-1. Select a propeller which fulfills
this requirement.
If operating under conditions which allow
the engine’s rpm to rise above the maximum recommended range (such as light
boat loads), reduce the throttle setting to
maintain the rpm in the proper operating
range.
9-1/4 x 9-3/4 - J
602021
qwe
11-3/4 x 9-1/4 - R
wqe
602031
E
1 Propeller diameter (in inches)
2 Propeller pitch (in inches)
3 Type of propeller (propeller mark)
Refer to the section “CHECKING PROPELLER” for instructions on propeller
removal and installation.
EMU12090
START-IN-GEAR PROTECTION
Yamaha outboard motors or Yamaha
approved remote control units are equipped
with start-in-gear protection device(s). This
feature permits the engine to be started
only when it is Neutral. Always select
Neutral before starting the engine.
1-16
-MEMO-
E
E
EMU00370
Chapter 2
BASIC COMPONENTS
MAIN COMPONENTS.............................2-1
1
OPERATIONS OF CONTROLS AND
OTHER FUNCTIONS ..............................2-2
Fuel tank ...............................................2-2
Gear shift lever .....................................2-3
Engine stop lanyard switch ...................2-3
Recoil starter handle.............................2-4
Starter button ........................................2-4
Tiller handle ..........................................2-4
Remote control .....................................2-6
Steering friction adjusting screw ...........2-9
Trim angle adjusting rod .....................2-10
Shallow water lever.............................2-11
Tilt lock mechanism ............................2-12
Tilt support lever .................................2-12
Top cowling lock lever .........................2-12
2
3
4
5
6
q
w
e
r
!0
o
!2
!1
i
t
y
u
!5
!7
!8
@2
!3
@1
!4
!9
!6
!5
@0
@1
!9
@3
@4 @5
!8
EMU12060
MAIN COMPONENTS
E
1 Top cowling
2 Top cowling lock lever
3 Cooling water pilot hole
4 Oil drain bolt
5 Anti-cavitation plate
6 Anode
7 Propeller
8 Cooling water inlet
9 Shallow water lever
*
0 Trim angle adjusting rod
q Tilt support lever
w Clamp bracket
e Starter button
*
r Engine stop lanyard switch
t Gear shift lever
2-1
*
y Engine stop button
u Clamp screw
i Throttle control grip
o Tiller handle
p Recoil starter handle
a Oil pressure indicator
s Engine stop button/Engine stop lanyard switch
d Tilt lock lever
f Remote control box
g Oil pressure indicator panel
* May not be exactly as shown; also may not be
included as standard equipment on all
models.
E
q
w
r
902051
e
EMU00390
OPERATIONS OF CONTROLS
AND
OTHER FUNCTIONS
EMU14650
FUEL TANK
If your model included a portable fuel tank,
its parts and functions are as follows.
1 Fuel hose joint
2 Fuel meter (if equipped)
3 Fuel tank cap
4 Air vent screw (if equipped)
EMU00420
Fuel Hose Joint
This connector is provided for connecting or
disconnecting fuel hose.
EMU15310
Fuel Meter
This meter is on the fuel tank cap. It shows
the approximate amount of fuel remaining in
the tank.
EMU00450
Fuel Tank Cap
This cap is for filling fuel. To remove it, turn
it counterclockwise.
EMU00460
Air Vent Screw
This screw is on the fuel tank cap. To
loosen it, turn it counterclockwise.
2-2
310016
q
ew
w
q
001138
E
EMU00510
GEAR SHIFT LEVER (for Tiller control model)
Turning the gear-shift lever towards you
engages the clutch with the forward gear so
that the boat moves ahead. Turning the
lever away from you engages the reverse
gear so that the boat moves astern.
1 Neutral
2 Forward
3 Reverse
EMU09310
ENGINE STOP LANYARD SWITCH
(for Tiller control model)
The lock-plate 1 must be attached to the
engine stop lanyard switch for the engine to
run. The lanyard 2 should be attached to a
secure place on the operator’s clothing, or
arm or leg. Should the operator fall overboard or leave the helm, the lanyard will pull
out the lock plate, stopping ignition to the
engine. This will prevent the boat from running away under power.
w
8 Attach the lanyard to a secure place
on your clothing, your arm or leg while
operating.
8 Do not attach the lanyard to clothing
that could tear loose. Do not route the
lanyard in such a way that it could
become entangled, preventing it from
functioning.
8 Avoid accidentally pulling the lanyard
during normal operation. Loss of
engine power means the loss of most
steering control. Also, without engine
power, the boat could slow rapidly.
This could cause people and objects
in the boat to be thrown forward.
2-3
NOTE:
The engine cannot be started with the lockplate removed.
E
209015
q
w
t
r
001532
e
503024
EMU00590
RECOIL STARTER HANDLE (If
equipped)
Pull the handle gently until resistance is felt.
Then vigorously pull the handle straight out
to crank the engine to start it.
EMU00600
STARTER BUTTON (for Tiller control
model)
When you push the starter button, the electric starter motor cranks the engine to start
it.
306022
EMU09430¯
TILLER HANDLE (for Tiller control
model)
T9.9EH
Moving the tiller handle sideways to adjust
the steering direction. In addition, this handle contains the functions as follows.
1 Throttle control grip
2 Throttle indicator
3 Throttle friction adjusting knob/screw
4 Engine stop button
5 Gear shift lever
EMU00650
Throttle Control Grip
The throttle control grip is on the tiller handle. Turn the grip counterclockwise to
increase speed and clockwise to decrease
speed.
2-4
E
001531
q
EMU00670
Throttle Indicator
The fuel consumption curve on the throttle
indicator shows the relative amount of fuel
consumed for each throttle position.
Choose the setting that offers the best performance and fuel economy for the desired
operation.
1 Throttle indicator
EMU12930
Throttle friction adjusting screw/ knob
A friction device in the tiller handle provide
resistance to movement of the throttle grip.
This is adjustable for operator preference.
An adjusting screw/knob is located within
the tiller handle.
502013
Resistance Knob/Screw
Increase Turn clockwise
Decrease Turn counterclockwise
When constant speed is desired, tighten the
adjusting screw/bolt to maintain the desired
throttle setting.
w
Do not over tighten the friction adjusting
screw/ knob.
If there is too much resistance, it may be
difficult to move the throttle grip, which
could result in an accident.
EMU00720
Engine Stop Button
Pushing this button opens the ignition circuit
and stops the engine.
001533
2-5
507011
1
2
3
y
q
w
e
r
t
701012
E
EMU00740
Gear shift lever
Turning the gear-shift lever forward (bow
side) engages the clutch with the forward
gear so that the boat moves ahead. Turning
the lever backward (stern side) engages the
reverse gear so that the boat moves astern.
1 Neutral
2 Forward
3 Reverse
EMU00950
REMOTE CONTROL
Both the shifter and the throttle are actuated
by the remote control lever. In addition, this
control also has the electrical switches.
1 Remote control lever
2 Neutral interlock trigger
3 Neutral throttle lever
4 Main switch
5 Engine stop lanyard switch
6 Throttle friction adjusting screw
y
u
w
F
r
t
EMU00980
Remote Control Lever
Moving the lever forward from the Neutral
position engages Forward gear. Pulling the
lever back from Neutral engages Reverse.
The engine will continue to run at idle until
the lever is moved about 35¡ (a detent can
be felt). Moving the lever farther opens the
N
q
r
e
R
y
t
u
701031
throttle, and the engine will begin to accelerate.
1 Neutral
2 Forward
3 Reverse
4 Shift
5 Fully closed
6 Throttle
7 Fully open
2-6
E
701036
ON
STARTOFF
701021
EMU00990
Neutral Interlock Trigger
To shift out of Neutral, the neutral interlock
trigger of the remote control lever must first
be pulled up.
EMU01000
N
q
w
000324
Neutral Throttle Lever
To open the throttle without shifting into
either Forward or Reverse, place the
remote control lever in the Neutral position
and lift the neutral throttle lever.
NOTE:
The neutral throttle lever will operate only
when the remote control lever is in Neutral.
The remote control lever will operate only
when the neutral throttle lever is in the
closed position.
2-7
1 Fully open
2 Fully closed
EMU01010
Main switch
The main switch controls the ignition system; its operation is described below.
8 OFF
Electrical circuits switched off.
(The key can be removed.)
8 ON
Electrical circuits switched on.
(The key cannot be removed.)
8 START
Starter-motor will turn and start engine.
(When the key is released, it returns automatically to “ON”.)
Loading...