Yamaha RXV-595-RDS Service manual

AV RECEIVER

RX-V595/R-V905/

RX-V595RDS

SERVICE MANUAL

IMPORTANT NOTICE

This manual has been provided for the use of authorized YAMAHA Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already known and understood by the users, and have therefore not been restated.

WARNING: Failure to follow appropriate service and safety procedures when servicing this product

IMPORTANT: The presentation or sale of this manual to any individual of firm does not constitute

The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributor's Service Division.

WARNING: Static discharges can destroy expensive components. Discharge any static electricity

IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before

may result in personal injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons, we advise all YAMAHA product owners that any service required should be performed by an authorized YAMAHA Retailer or the appointed service representative.

authorization, certification or recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.

your body may have accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).

you apply power to the unit.

n CONTENTS

TO SERVICE PERSONNEL ........................................... 1

REMOTE CONTROL PANELS ....................................... 1

FRONT PANELS ............................................................. 2

REAR PANELS ........................................................... 3~4

SPECIFICATIONS ....................................................... 5~6

INTERNAL VIEW ............................................................ 7

DISASSEMBLY PROCEDURES .................................... 7

SELF DIAGNOSIS FUNCTION ................................ 8~19

FACTORY PRESET ...................................................... 20

AMP ADJUSTMENT ..................................................... 21

This Service Manual uses recycled paper.

100654

TUNER ADJUSTMENT ........................................... 22~25

IC DATA .................................................................. 26~35

DISPLAY DATA ........................................................... 36

BLOCK DIAGRAM .................................................. 37~39

PRINTED CIRCUIT BOARD ................................... 40~55

SCHEMATIC DIAGRAM ......................................... 56~63

PARTS LIST ............................................................ 64~79

PRINTED CIRCUIT BOARD ................................... 80~81

REMOTE CONTROL TRANSMITTER ......................... 82

RX-V595/R-V905/RX-V595RDS

■ TO SERVICE PERSONNEL

1. Critical Components information. Components having special characteristics are marked and must be replaced with parts having specifications equal to those originally installed.

2. Leakage Current Measurement (For 120V Model only). When service has been completed, it is imperative that you verify that all exposed conductive surfaces are properly insulated from supply circuits. Meter impedance should be equivalent to 1500 ohm shunted by 0.15µF.

•

Leakage current must not exceed 0.5mA.

•

Be sure to test for leakage with the AC plug in both polarities.

•

WALL

OUTLET

EQUIPMENT

UNDER TEST

INSULATING

TABLE

AC LEAKAGE

TESTER OR

EQUIVALENT

"CAUTION"

"F804: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE,REPLACE ONLY WITH SAME TYPE 8.0A, 250V FUSE."

CAUTION

A V

F804: REPLACE WITH SAME TYPE 8.0A, 250V FUSE.

ATTENTION

F804: UTILISER UN FUSIBLE DE RECHANGE DE MEME TYPE DE 8.0A, 250V FUSE.

WARNING: CHEMICAL CONTENT NOTICE!

The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (where applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm.

DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHATSOEVER!

Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor!

If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food.

■ REMOTE CONTROL PANELS

▼ U,C,R,T and L models ▼ A,B and G models

■ FRONT PANELS

▼ RX-V595 (U, C, R, T, A and L models)

▼ R-V905 (U, C, R, T and A models)

RX-V595/R-V905/RX-V595RDS

▼ RX-V595RDS (B and G models)

RX-V595/R-V905/RX-V595RDS

■ REAR PANELS

▼ RX-V595/R-V905 U model

▼ RX-V595/R-V905 C model

▼ RX-V595/R-V905 R model

▼ RX-V595/R-V905 T model

▼ RX-V595/R-V905 A model

▼RX-V595RDS B model

RX-V595/R-V905/RX-V595RDS

▼RX-V595RDS G model

▼ RX-V595 L model

RX-V595/R-V905/RX-V595RDS

■ SPECIFICATIONS

■AUDIO SECTION

Minimum RMS Output Power Per Channel

(Power Amp. Section)

U, C models

MAIN L/R, REAR L/R

20Hz to 20kHz, 0.04% THD, 8Ω 70W+70W 1kHz, 0.07% THD, 8Ω 85W+85W

CENTER

20Hz to 20kHz, 0.04% THD, 8Ω 70W 1kHz, 0.07% THD, 8Ω 85W

R,T,A,B,G,L models

MAIN L/R, REAR L/R

20Hz to 20kHz, 0.04% THD, 8Ω 65W+65W 1kHz, 0.07% THD, 8Ω 80W+80W

CENTER

20Hz to 20kHz, 0.04% THD, 8Ω 65W 1kHz, 0.07% THD, 8Ω 80W

Maximum Power (EIAJ)

R, T models only

MAIN L/R, REAR L/R

1kHz, 10% THD, 8Ω 105W+105W

CENTER, 1kHz, 10% THD, 8Ω 105W

Dynamic Power Per Channel (IHF)

MAIN L/R

U, C models

8/6/4/2Ω

100W+100W/120W+120W/145W+145W/170W+170W

R,T,A,B,G,L models

8/6/4/2Ω

90W+90W/110W+110W/135W+135W/160W+160W

DIN Standard Output Power Per Channel

G model only

MAIN L/R, 1kHz, 0.7% THD, 4Ω 110W+110W

Dynamic Headroom(8Ω)

U, C models only 1.55dB

IEC Power

G model only

MAIN L/R, 1kHz, 0.04% THD, 8Ω 75W+75W

Power Band Width

MAIN L/R, 0.1% THD, 35W, 8Ω 10Hz to 50kHz

Damping Factor (SPEAKER A)

MAIN L/R, 20Hz to 20kHz, 8Ω 60

Input Sensitivity/Input Impedance

PHONO (MM) 2.5mV/47kΩ CD etc. 150mV/47kΩ MAIN L/R (EXTERNAL DECODER) 150mV/47kΩ CENTER 150mV/40kΩ SURROUND L/R 150mV/40kΩ SUB WOOFER 150mV/40kΩ

Maximum Input Signal Level (1kHz)

PHONO (MM), 0.1% THD 110mV CD etc. (EFFECT ON), 0.5% THD 2.2V

Output Level/Output Impedance

REC OUT 150mV/1.2kΩ SUB WOOFER (MAIN SP : SMALL) 2.1V/1.2KΩ

B,G models only

PRE OUT 4V/1.2KΩ

Headphone Jack Rated Output/Impedance

CD etc., Input=1kHz, 150mV, RL=8Ω 0.5V/390Ω

Frequency Response(20Hz to 20kHz)

CD etc., MAIN 0±0.5dB

RIAA Equalization Deviation

PHONO (MM) 0±0.5dB

Total Harmonic Distortion(20Hz to 20kHz)

PHONO (MM) to REC OUT (1V) 0.02% CD etc.(EFFECT OFF) to MAIN SP OUT(35W/8Ω)

0.025%

Signal-to-Noise Ratio(IHF-A-Network)

PHONO (MM), Input 5mV shorted, REC OUT

U, C, R, T models 86dB A, B, G, L models 81dB

CD etc,(EFFECT OFF), Input 150mV shorted, SP OUT

96dB

Residual Noise(IHF-A-Network)

MAIN L/R, SP OUT 150µV

Channel Separation(Vol. –30dB, EFFECT OFF)

PHONO, Input shorted, 1kHz/10kHz 60dB/55dB CD etc, Input 5.1kΩ terminated, 1kHz/10kHz

60dB/45dB

Tone Control Characteristics

BASS : Boost/Cut ±10dB(50Hz)

: Turnover Frequency 350Hz

TREBLE : Boost/Cut ±10dB(20kHz)

: Turnover Frequency 3.5kHz

Filter Characteristics

MAIN, REAR SP SMALL : H.P.F. fc=90Hz, 12dB/oct. SUB WOOFER : L.P.F. fc=90Hz, 18dB/oct.

■FM SECTION Tuning Range

U, C models 87.50 to 107.9MHz R, T models (Frequency Step: 100kHz)

87.50 to 108.0MHz

(Frequency Step: 50kHz)

87.50 to 108.0MHz

A, B, G, L models 87.50 to 108.00MHz

50dB Quieting Sensitivity (IHF)

U, C, R, T models only

Mono, 1kHz, 100% mod 1.6µV(15.3dBf) Stereo, 1kHz, 100% mod 23µV(38.5dBf)

Usable Sensitivity (DIN)

A, B, G, L models only

DIN, Mono(S/N 26dB) 0.9µV DIN, Stereo(S/N 46dB) 28µV

Alternate Channel Selectivity

U, C, R, T models (±400kHz) 75dB A, B, G, L models (±300kHz)

Selectivity(two signals, 40kHz Dev.) 55dB

Signal-to-Noise Ratio

U, C, R, T models (IHF)

Mono/Stereo 81dB/75dB

A, B, G, L models (DIN-Weighted, 40kHz Dev.)

Mono/Stereo 75dB/69dB

Harmonic Distortion (1kHz)

Mono/Stereo 0.1%/0.2%

Stereo Separation (1kHz) 48dB Frequency Response (20Hz to 15kHz) 0±1dB Output Level (1kHz)

U, C, R, T models (100% mod.) 550mV A, B, G, L models (40kHz Dev.) 550mV

Antenna Input 75Ω unbalanced

RX-V595/R-V905/RX-V595RDS

■AM SECTION Tuning Range

U, C models 530 to 1710kHz R, T models (Frequency Step : 10kHz) 530 to 1710kHz

(Frequency Step : 9kHz) 531 to 1611kHz

A, B, G, L models 531 to 1611kHz

Usable Sensitivity 300µV/m Signal-to-Noise Ratio 52dB Output Level (1kHz, 30% mod.) 150mV Antenna Loop antenna

■VIDEO SECTION Video Signal Type

U, C models NTSC R model NTSC/PAL T, A, B, G, L models PAL

Video Signal Level 1Vp-p/75Ω S-Video Signal Level

B, G models only Y:1Vp-p/75Ω,C:0.286Vp-p/75Ω

Maximum Input Level 1.5Vp-p Signal-to-Noise Ratio 50dB Monitor Out Frequency Response(–3dB) 5Hz~10MHz

■GENERAL Power Supply

U, C, models AC120V, 60Hz R model AC110/120/220/240V, 50/60Hz T model AC220V, 50Hz A model AC240V, 50Hz B, G, L models AC230V, 50Hz

Power Consumption

U model 280W C model 310W/410W R, T models 310W R, A, B, G, L models 300W

Maximum Power Consumption

R model only

5CH Simultaneous output, 10% THD 650W

AC Outlet

U, C, R, T, G, L models, Switched x 2 100W max(Total) A, B models, Switched x 1 100W max

Dimensions(W x H x D) 435 x 151 x 391mm

(17/1/8" x 5-15/16" x 15-3/8")

Weight 12.5kg(27Ibs. 9 oz) Accessories AM loop antenna x 1

Indoor FM antenna x 1

Remote Control Transmitter x 1

Battery (siza "AA", "R06") x 2

●DIMENSIONS

21.5

349.5(13-3/4")

130(5-3/32")

435(17-1/8")

Units: mm (inch)

WARNING

Do not change the IMPEDANCE SELECTOR switch setting while the power to this unit is on, otherwise this unit may be damaged.

IMPEDANCE SELECTOR

(7/8")

391(15-3/8")

(13/16")

151(5-15/16")

(27/32")

* Specifications subject to change without notice.

U ......... U. S. A. model A .........Australian model

C ......... Canadian model B .........British model

R ......... General model G .........European model

T.......... China model L ..........Singapore model

Manufactured under license from Dolby Laboratories Licensing Corporation."DOLBY" , "AC-3", "Pro Logic", and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. Copyright 1992 Dolby Laboratories, inc. All rights reserved.

RX-V595/R-V905/RX-V595RDS

■ INTERNAL VIEW

12 345 6 7 8 9 0 A B C

#14

1 POWER TRANSFORMER 2 P.C.B. MAIN (3) 3 P.C.B. OPERATION (7)

(R, T models only)

4 P.C.B. OPERATION (3) 5 P.C.B. MAIN (4) 6 P.C.B. MAIN (8) 7 P.C.B. OPERATION (6) 8 P.C.B. MAIN (2) 9 P.C.B. MAIN (1) 0 P.C.B. INPUT (2) A P.C.B. INPUT (1) B P.C.B. INPUT (3) C P.C.B. TUNER D P.C.B. MAIN (5) E P.C.B. OPERATION (5) F P.C.B. OPERATION (4) G P.C.B. MAIN (7) H P.C.B. OPERATION (1) I P.C.B. MAIN (6) J P.C.B. INPUT (4) K P.C.B. OPERATION (2) L P.C.B. DSP

EFGHIJKLD

■ DISASSEMBLY PROCEDURES

(Remove parts in disassembly order as numbered.)

1. Removal of Top Cover

Remove 4 screws (1) and 4 screws (2) in Fig. 1.

2. Removal of Front Panel

a. Remove 5 knobs. b. Remove 6 screws (3) in Fig. 1.

#13

Top Cover

Knob

Front Panel

Fig.1

RX-V595/R-V905/RX-V595RDS

■ SELF DIAGNOSIS FUNCTION

1. PURPOSE AND OPERATION

The RX-V595/R-V905/RX-V595RDS has a Self Diagnosis Function to locate a faulty part, if any, by inspecting and taking measurements.

There are 11 main items in the diagnostic menu and some of them have sub-menu items as listed below.

No.

3 4

MAIN MENU

ANALOG THROUGH

DSP THROUGH

AC–3/DTS THROUGH PRO LOGIC

SPEAKERS SET

EFFECT OFF /DISPLAY CHECK

MANUAL TEST

FACTORY PRESET

AD DATA CHECK

STATUS

VERSION CHECK /DSP CPU SUM /EXIT

SUB MENU

1. MAIN BYPASS

2. DSP 0dB

1. YSS908–SRAM

2. YSS908

3. DSP FULL BIT

1. STATUS (BINARY FORM)

1. CENTER LARGE

2. EFFECT OFF

1. MAIN : SMALL 0dB

2. MAIN : LARGE 0dB

3. MAIN : LARGE –10dB

4. LFE/BASS : MAIN CENTER : NONE

5. LFE/BASS : MAIN

6. LFE/BASS : SWFR

7. CENTER : NONE

8. CENTER : SMALL REAR : SMALL

9. FRONT MIX

1. EFFECT OFF

2. VFD DISP OFF

3. VFD DISP ALL

4. CHECKED PATTERN

5. RELEASE DATE

1. ALL

2. MAIN L

3. CENTER

4. MAIN R

5. REAR R

6. REAR L

7. LFE

1. INHIBIT(Inhibit Memory Init)

2. RESERVED (Init. Memory)

1. – – –

2. KEY

3. TUNING SIGNAL

4. DC PROTECTION

5. PS PROTECTION

1. DSP CPU STATUS

2. CHANNEL STATUS

3. VERSION INFORMATION

4. CHECK SUM

5. BSI0 (AC3/DTS)

6. BSI1

7. BSI2

8. BSI3

9. BSI4

10. BSI5

1. MAIN MC CHECK SUM

2. SUB MC CHECK SUM

3. MAIN M.C. VERSION

4. SUB M.C. VERSION

5. PORT INFORMATION

6. EXIT

REMOTE CONTROL CODE (KEY) 7A–88 ("1" (DSP mode))

– – – 7A–89 ("2" (DSP mode))

– – – – – –

– – – 7A–8A ("3" (DSP mode))

– – – 7A–8B ("4" (DSP mode))

7A–8C ("5" (DSP mode)) 7A–8D ("6" (DSP mode)) 7A–8E ("7" (DSP mode))

7A–8F ("8" (DSP mode)) 7A–90 ("9" (DSP mode)) 7A–91 ("0" (DSP mode)) – – –

7A–12 ("ENTER" (DSP mode)) – – –

– – – – – – – – – – – –

– – – – – – – – – – – – – – – – – – – – –

– – – – – –

– – – – – – – – –

– – – – – – – – – – – – – – – – – – – – – – – – – – – – – –

– – –

– – – – – – – – –

RX-V595/R-V905/RX-V595RDS

2. BEGINNING AND CANCELLATION

(1) STARTING UP THE FUNCTION AND THE DISPLAY

After starting up, menu No. 1 is selected.

A. How to start diagnostic program

Using the front panel keys of the main unit.

Hold down the "INPUT MODE" and "FM/AM" keys simultaneously, and press the "STANDBY/ON" key; submenu No. 1 of diagnosis main menu No. 1 will start.

TUNING

FRONT PANEL

MEMORY EDIT

B. Settings for start-up of diagnostic program

The settings used when starting the diagnostic program are as follows.

EFFECT LEVEL :

CHANNEL CENTER R SUR L SUR SWFR LEVEL (dB) 0 0 0 0

MUTING : OFF

INPUT (VIDEO) : DVD/LD (DVD/LD)

CENTER SPEAKER : LARGE

REAR SPEAKER : LARGE

MAIN SPEAKER : LARGE

LFE/BASS OUT : SWFR

C. Start-up display

The information of the protection function appears on the front panel display of the main unit.

MODE

FM/AM

"FM/AM" key "INPUT MODE" key

DOWN UP

TUNING

INPUT MODE

RX-V595/R-V905/RX-V595RDS

● FL display at start-up of diagnostic program

When the diagnostic program has started, the history (*2) of the protection function (*1) is displayed. If the protection function has been activated in the past, the type and voltage value are displayed. After a few seconds the diagnosis function menu will appear.

(*1) If a faulty condition is detected such as excessive current, a bad power supply or excessive amplifier DC offset, the Power will be switched OFF automatically.

(*2) The protection records will be cleared when "RESERVED" is selected in diagnosis menu No. 8 and FACTORY

PRESET is engaged.

● History of protection function

Each case of the history of the protection function is displayed as shown below.

1 DVD/LD NO PROTECT

1 DVD/LD I PROTECT

1 DVD/LD PS : 21%

1 DVD/LD DC : 19%

Appears when the protection function has not been activated.

Appears when the current protection function has been activated. When power is turned on in an abnormal status, the power relay will come on, protection will operate immediately, and power will turn off.

Appears when the power protection function has been activated. For the % value, the voltage at that point is shown by 5V/100%. When power is turned on in an abnormal status, power will turn off after half a second.

Appears when the power amp DC protection function has been activated. For the % value, the voltage at that point is shown by 5V/100%. When power is turned on in an abnormal status, power will turn off after two seconds.

(2) RELEASING METHOD

The diagnosis function can be released by any of the following procedures. Take care with the setting of backup memory initialization menu (diagnosis No. 8) when releasing the diagnosis function:

1. Select diagnosis menu No. 11/submenu No. 6 "EXIT".

2. Press the "STANDBY/ON" key on the main unit or "STANDBY" key on the remote control to turn power off.

RX-V595/R-V905/RX-V595RDS

3. OPERATION AND DISPLAY WHEN STARTING DIAGNOSIS FUNCTION

(1) Selection of diagnostic menu

The diagnostic menu and the sub-menu can be selected by using the front panel keys of the main unit or the remote control unit.

● Selection by using the front panel keys

The main menu can be changed cyclically by using the "TUNING UP/DOWN" keys, and the submenu, by using the "PROGRAM / " keys. The "UP" or " " key will increase the main or submenu number.

FRONT PANEL

DOWN UP

TUNING

INPUT MODE

TIME/

LEVEL

Reverse Forward Reverse Forward

SET

Main menu Sub menu

EFFECT

PROGRAM

● Selection by using the remote control unit

The remote control codes in the menu list (on page 8) correspond to the DSP program, test and effect keys. See the figure on the right.

(2) Other functions available while diagnosis function is active

Listed below are the other functions available while the diagnosis function is active. ¥ Selecting input source (Tape monitor/Ext. decoder)

¥ Adjusting effect level (Center, Rear, Sub-woofer) ¥ Adjusting master volume ¥ Muting on/off ¥ Power on/off

(3) Diagnosis default status

When not otherwise specified, default settings and values in each menu are as follows: ¥ All SPEAKERS : LARGE

¥ ALL electronic VRs : 0dB ¥ DYNAMIC RANGE : MAX ¥ LFE LEVEL : 0dB (—10dB DOLBY DIGITAL LFE) ¥ CENTER DELAY : 0ms

4. CONTENTS OF DIAGNOSIS FUNCTION

This section describes the contents of the self diagnosis function in detail.

No.1 ANALOG THROUGH

The input is fixed to analog (A/D). There are two submenus.

1. MAIN BYPASS

The MAIN L/R signals bypass the analog circuits to be output. For CENTER/SUBWOOFER, FRONT L/R and REAR L/R, the MAIN L/R signals via the DSP are output without

being processed (through). (Remote control code 7A-88)

: This shows that the device is not operating.

2. DSP 0dB

MAIN L/R, CENTER/SUBWOOFER/LFE, FRONT L/R and REAR L/R pass through the DSP without being processed.

: This shows that the device is not operating.

DIR2

CODEC.DA

AK4526

YM3436

CODEC.AD

AC3Dav(YSS908)

AK4526

DECODER

AK4320

1M SRAM

DSP

ANALOG IN

L/R L/R

FRONT R

REAR L REAR R

CENTER

SUBWOOFER

L/R

DIGITAL IN

FRONT L

MAIN R

MAIN L

DIR2

CODEC.DA

AK4526

YM3436

CODEC.AD

AC3Dav(YSS908)

AK4526

DECODER

AK4320

1M SRAM

DSP

ANALOG IN

L/R L/R

FRONT R

REAR L REAR R

CENTER

SUBWOOFER

L/R

DIGITAL IN

FRONT L

MAIN R

MAIN L

1 DVD/LD DSP 0DB

1 DVD/LD MAIN BYPAS

• INPUT : DVD/LD (Analog signal) (Lch and Rch, 1KHz, –20dBV)

• OUTPUT : SPEAKERS

MAIN L : 23.8 dBV REAR L : 23.7 dBV MAIN R : 23.8 dBV REAR R : 23.7 dBV CENTER: 23.7 dBV

• INPUT : DVD/LD (Analog signal) (Lch and Rch, 1KHz, –20dBV)

• OUTPUT : SPEAKERS

MAIN L : 23.7 dBV REAR L : 23.6 dBV MAIN R : 23.7 dBV REAR R : 23.6 dBV CENTER: 23.6 dBV

RX-V595/R-V905/RX-V595RDS

No.2 DSP THROUGH

The input is automatically discriminated by signal detection and switched with priorities AC3>PCM Audio>analog. There are the following three submenus.

1. YSS908-SRAM

2 DVD/LD YSS908SRAM

MAIN L/R are input to the DSP via AC3Dav, pass through SRAM, and are then output to all channels without being processed. (Remote control code 7A-89)

CODEC.AD

ANALOG IN

AC3Dav(YSS908)

L/R

AK4320

MAIN L

MAIN R

AK4526

DECODER

DIR2

DIGITAL IN

YM3436

2. YSS908

MAIN L/R are input to the DSP via AC3Dav, and then output to all channels without being processed.

2 DVD/LD YSS908

L/R

DSP

L/R L/R

1M SRAM

L/R

CODEC.DA

SUBWOOFER

AK4526

• INPUT : DVD/LD (Analog signal)

• OUTPUT : SPEAKERS

(Lch and Rch, 1KHz, –20dBV)

MAIN L : 23.7 dBV REAR L : 23.5 dBV MAIN R : 23.7 dBV REAR R : 23.5 dBV CENTER: 23.6 dBV

CENTER

REAR L REAR R

FRONT L FRONT R

CODEC.AD

ANALOG IN

AC3Dav(YSS908)

AK4320

L/R

AK4526

DECODER

DIR2

DIGITAL IN

L/R

DSP

L/R

CODEC.DA

AK4526

YM3436

• INPUT : DVD/LD (Analog signal)

: This shows that the device is not operating.

3. DSP FULL BIT

1M SRAM

2 DVD/LD DSP FULL

• OUTPUT : SPEAKERS

MAIN L/R are input to the DSP via AC3Dav, and then output to all channels without being processed. The head margin is abolished, and DSP outputs digital full-bit signals. Same as the above menu, except that the digital data is output to DA with full bits.

• INPUT : DVD/LD (Analog signal)

• OUTPUT : SPEAKERS

(Lch and Rch, 1KHz, –20dBV)

MAIN L : 23.8 dBV REAR L : 23.8 dBV MAIN R : 23.8 dBV REAR R : 23.8 dBV CENTER: 23.8 dBV

(Lch and Rch, 1KHz, –20dBV)

MAIN L : 13.8 dBV REAR L : 22.8 dBV MAIN R : 13.8 dBV REAR R : 22.8 dBV CENTER: 16.8 dBV

MAIN L MAIN R

FRONT L FRONT R

REAR L

REAR R

CENTER

SUBWOOFER

RX-V595/R-V905/RX-V595RDS

No.3 AC3 THROUGH

The input is digital signal only. AC3 (DOLBY DIGITAL) decoding operation is executed, according to the input source.

1. STATUS(BINARY FORM)

3 DVD/LD 3T00000001

AC3 (DOLBY DIGITAL) decoded signals are output to each channel via AC3Dav.

CODEC.AD

ANALOG IN

AC3Dav(YSS908)

AK4320

L/R

AK4526

DECODER

DSP

CODEC.DA

DIR2

DIGITAL IN

DOLBY DIGITAL

PRO LOGIC

C/LFEC/LFE

LS/RSLS/RS

AK4526

YM3436

: This shows that the device is not operating.

AC3 Status Info. : bit 7 6 5 4 3 2 1 0

(Invalid in DTS) 1 0 0 00000

IEC958 digital data bit IEC958 commercial-use device bit

IEC958 digital format error Demodulator muting (without RF signal)

1 for audio other than PCM linear audio 1 during red DTS lock 1 during DTS decode OK 1 during AC3 decode OK

1M SRAM

No.4 PRO LOGIC

The input is automatically discriminated by PCM>analog. AC3 (DOLBY DIGITAL) is prohibited. The submenu is switched between PRO LOGIC (AUTO BALANCE OFF) and EFFECT OFF.

MAIN L

MAIN R

CENTER

SUBWOOFER

REAR L REAR R

1. CENTER LARGE

4 DVD/LD P. LGC C:L

The input is automatically detected whether it is PCM or analog. With analog, PCM audio or AC3 (DOLBY DIGITAL) 2/0 input, the L, R, C and S signals are PRO LOGIC decoded and output. With AC3 (DOLBY DIGITAL) other than 2/0, PRO LOGIC does not operate, and AC3 (DOLBY DIGITAL) playback is executed. (Remote control code 7A-8A)

CODEC.AD

ANALOG IN

AC3Dav(YSS908)

L/R

AK4320

MAIN L

MAIN R

AK4526

DECODER

DSP

CODEC.DA

DIR2

DIGITAL IN

YM3436

2. EFFECT OFF

MAIN L/R are bypassed and output.

4 DVD/LD EFFECT OFF

DOLBY DIGITAL

PRO LOGIC

1M SRAM

AK4526

• INPUT : DVD/LD (Analog signal) (Lch and Rch, or Lch only, 1KHz, –20dBV)

• OUTPUT : SPEAKERS (INPUT : Lch and Rch ) (INPUT : Lch only)

MAIN L : –15.4 dBV REAR L : 23.8 dBV MAIN R : –14.2 dBV REAR R : –25.0 dBV CENTER: 26.6 dBV CENTER : –12.5 dBV REAR L : –6.0 dBV REAR L : –6.0 dBV REAR R : –6.5 dBV REAR R : –6.2 dBV

CENTER

REAR L REAR R

RX-V595/R-V905/RX-V595RDS

No.5 SPEAKERS SET

The input is automatically discriminated by AC3>PCM>analog. There are the following 9 submenu items: The signal from the DSP block is normally in the effect off status for menu

items 1-4. For other menu items, the same signal as in 2. DSP THROUGH: YSS908 menu is output.

5 DVD/LD MAIN:S 0DB

5 DVD/LD B:MAIN C:N

5 DVD/LD C:NONE

5 DVD/LD MAIN:L 0DB

5 DVD/LD LFE/B:MAIN

5 DVD/LD C:S REAR:S

5 DVD/LD MAIN:L —10

5 DVD/LD LFE/B:SWFR

5 DVD/LD FRONT MIX

The analog switches in each submenu are set as follows:

SUB MENU REMOTE

CODE

1 MAIN:S 0DB 7A-8B LARGE LARGE SMALL 0dB SWFR MAIN L/R 2 MAIN:L 0DB 7A-8C LARGE LARGE LARGE 0dB SWFR MAIN L/R 3 MAIN:L -10 7A-8D LARGE LARGE LARGE -10dB SWFR MAIN L/R 4 B:MAIN C:N 7A-8E NONE LARGE LARGE 0dB MAIN MAIN L/R 5 LFE/B:MAIN 7A-8F LARGE LARGE LARGE 0dB MAIN LFE -> L/R 6 LFE/B:SWFR 7A-90 LARGE LARGE LARGE 0dB SWFR LFE -> SWFR 7 C:NONE 7A-91 NONE LARGE LARGE 0dB SWFR CENTER -> L/R 8 C:S REAR:S SMALL SMALL LARGE 0dB SWFR CENTER/REAR 9 FRONT MIX 7A-12 LARGE LARGE LARGE 0dB SWFR FRONT -> L/R

CENTER SP

REAR SP MAIN SP MAIN LFE/BASS OUTPUT

LEVEL

LARGE:Mode in which speakers with high bass-sound playback capability (large unit) are used. Sound in all signal widths

is output.

SMALL: Mode in which speakers with low bass-sound playback capability (small unit) are used. Signal of less than 90 Hz

is mixed with the channel specified by LFE/BASS.

NONE :Mode in which center speaker is not used. The center components with 3 dB subtracted are br anched into MAIN

L/R.

LFE/B : MAIN

:Mode in which subwoofer speaker is not used. The subwoofer components with 4.5 dB subtr acted are br anched

into MAIN L/R. But because of the phase difference, the MAIN L/R output is not simpleminded add level.

Purpose of the submenu as follows:

SUB MENU PURPOSE

1 MAIN:S 0DB Verification of the High and low pass filter responce and gain in the bass redirection mode. 2 MAIN:L 0DB Refference of the sub menu No. 1 and 2. 3 MAIN:L -10 Verification of the effect in the main level function. 4 B:MAIN C:N Verification of the effect the mixing circuit to the main channel. 5 LFE/B:MAIN Verification of the bass mix gain. 6 LFE/B:SWFR Verification of the LFE maximum output. 7 C:NONE Verification of the center mix gain. 8 C:S REAR:S Verification of the High and low pass filter responce and gain in the bass redirection mode. 9 FRONT MIX Verification of the front mix gain.

RX-V595/R-V905/RX-V595RDS

No.6 DISPLAY CHECK

Check program for FL display. The display status will change as follows with submenu operation. The signal is processed with EFFECT OFF.

6 DVD/LD DISP CHECK

Initial displayed. All segments are turned off All segments are turned on

6 DVD/LD 9807150942

Segments ON in a lattice.Release date displayed.

All segments are turned on and off to detect defects in the FL driver and FL display segments. Then the FL driver operation is checked by the dimmer control. Finally, all segments are turned on and off alternately (in lattice form), to check for a short-circuit between adjacent segments.

No.7 MANUAL TEST

The noise generator built into the DSP outputs test noise from the channel specified by the submenu.

7 DVD/LD TEST ALL

7 DVD/LD TEST MAINR

7 DVD/LD TEST MAINL

7 DVD/LD TEST REARR

7 DVD/LD TEST CNTR

7 DVD/LD TEST REARL

7 DVD/LD TEST LFE

No.8 FACTORY PRESET

The menu is used to reserve whether or not to set the back-up data for the effect level, delay time and so on to the factory preset state. The Signal is processed with EFFECT OFF.

8 DVD/LD PRESET INH

8 DVD/LD PRESET RES

Caution : Before setting to the PRESET DATA, write down the existing preset memory contents of the Tuner in a table as

shown below. (This is because setting to the PRESET DATA will cause the memory contents to be as factory set, i.e., all the preset memory by the user will be erased.)

Page P1 P2 P3 P4 P5 P6 P7 P8

A B C D E

1. INHIBIT: The back-up data is not initialized. To keep the data set by the user, check that this mode has been selected and cancel the self diagnosis function.

2. RESERVED: When the self diagnosis function is canceled, the backup data is initialized to the factory preset state. For the contents of the initialization, refer to page 20. The protection data is also reset.

RX-V595/R-V905/RX-V595RDS

No.9 AD DATA CHECK

The A/D conversion values of the main CPU which detects key scan, protection, etc. are displayed in % (100%: 5V). All signal processing before this menu is executed will be held. The keys on the main unit cannot be operated to detect the values of all keys in the K1/K2/K3/K4. Turning the rotary encoder (input selector on the main unit) will switch the submenu.

9 DVD/LD AD CHECK

9 DVD/LD 33999999

K1 K2 K3 K4

9 DVD/LD SI 0

9 DVD/LD DC 7

9 DVD/LD

PS 40

K1/K2/K3/K4: Panel key on main unit

See Table 1.

Turning the rotary encoder. SI: Tuner signal level

Turning the rotary encoder. DC: DC protection value

(normal value: 1-13)

Press the "PROGRAM "key. PS: Power voltage protection value

(normal value: 28-54)

Table 1

AD Value

0112336516784

TIME/

LEVEL

TAPE/MD MON

/EXT. DECODER

A/B/C/D/E

SET

TUNING

DOWN

–

TUNING

MEMORY

INPUT MODE

EDIT

EON

EFFECT

TUNING

MODE

PTY SEEK

MODE

PROGRAM

FM/AM

Cautions:

1.If K1/K2/K3/K4 are more than –4% from the reference values, normal operation will not be executed.

2.If DC and PS are outside the normal values, the protection function will operate and power will turn off.

PTY SEEK

START

PROGRAM

RDS

MODE

No.10 STATUS FROM DSP MICOM

The status data from the DSP microprocessor is sequentially displayed in a hexadecimal number. All signal processing before this menu is executed will be held.

1st 2nd 3rd 4th

10 DVD/LD 0 00000000

10 DVD/LD 1 00000000

10 DVD/LD 2 00000000

RX-V595/R-V905/RX-V595RDS

10 DVD/LD 3 00000000

10 DVD/LD 6 00000000

10 DVD/LD 9 00000000

[STATUS 0]

<1st Byte>

acmod: If it is 1000B or more with DTS 7.1 signal, the DSP block will be muted.

<2nd Byte>

[Note]

IEC958: Standard to identify the PCM bit stream signal. Digital format error refers to a digital signal with the sampling frequency undefined (neither 44.1k, 32k nor 48k). Since the operation of each device cannot be assured at fs outside specifications, the sub-microprocessor handles this status as the forced analog mode (ignored even if decoding is OK from the detection terminal level), and selects the signal from the analog input terminal. Since the sub-microprocessor transmits 000B (analog) for STATUS#0 bits 4-6 to the main microprocessor, the main microprocessor visually operates in the same way as with digital unlocking.

10 DVD/LD 4 00000000

10 DVD/LD 7 00000000

bit7 Mute request bit3 acmod bit6 fs bit2 bit5 000B:Analog 001B:32kHz bit4 bit0

bit7 1 during AC3 decode OK bit3 Demodulator muting (without RF signal) bit6 1 during DTS decode OK bit2 IEC958 digital format error bit5 1 during red DTS lock bit1 IEC958 commercial use device bit bit4

010B:44.1kHz 011B:48kHz Others:Don't care

1 for audio other than PCM linear audio

bit1

bit0 IEC958 digital data bit

0000B:1+1 0001B:1/0 0010B:2/0 0011B:3/0 0100B:2/1 0101B:3/1 0110B:2/2 0111B:3/2 1000B:7.1

10 DVD/LD 5 00000000

10 DVD/LD 8 00000000

Indicate

bit 7 6 5 4 3 2 1 0

Indicate bit

3210 7654

0 0000 1 0001 2 0010 3 0011 4 0100 5 0101 6 0110 7 0111 8 1000

9 1001 A 1010 B 1011 C 1100 D 1101

E 1110

F1111

<3rd Byte>

bit7 AC3 KARAOKE bit3 On-board write mode bit6 DIR2 LOCKN bit2 The number of digital inputs is 2 (equivalent to 595) bit5 DIR2 ERR bit1 DSP is AC3D2 (DTS present) bit4 AC3D MUTE bit0 RF DEM present

<4th Byte> Always “00”

[STATUS 1] IEC958 channel status bits 00-31 available from DIR2

<1st-byte> bits 00-07 <2nd-byte> bits 08-15 <3rd-byte> bits 16-23 <4th-byte> bits 24-31

[STATUS 2] 4-byte ASCII code of sub CPU version data [STATUS 3] Displays the check sum of sub microprocessor program area with ASCII 4 bytes in a hexadecimal number. [STATUS 4] Displays the bit stream information contained in AC-3/DTS signal from the first byte. [STATUS 5-9] Displays the bit stream information contained in AC-3 signal from the first byte.

RX-V595/R-V905/RX-V595RDS

No.11 CPU VERSION/CHECK SUM/PORT INFO/EXIT DIAG

The check sum, version and port setting of main CPU/DSP CPU are displayed. The signal is EFFECT OFF. Operating the submenu will finish self-diagnosis, and ordinary operation mode will be restored. The suffix letter ("B" in the following) of version indication is for compatibility of communications between the main and DSP microprocessors. Combining microprocessors with different suffixes will make normal operation impossible.

11 DVD/LD M-SM:XXXXX

11 DVD/LD S-SM:XXXXX

11 DVD/LD M-VER:Z04B

11 DVD/LD S-VER:Z08B

11 DVD/LD P:00000000

Main microprocessor check sum

DSP microprocessor check sum

Main microprocessor version

DSP microprocessor version

One suffix letter is for compatibility of communications between the main and DSP microprocessors. * Use microprocessors with the same suffix.

bit76543210

00000000

EXIT

✽1

Tuner Mode V1 (Port 95) 0*11*21*3 Tuner Mode V2 (Port 96) 101

*1 AM:530–1710kHz/10kHz FM: 87.5–107.9MHz/200kHz (U, C models) *2 AM:531–1611kHz/9kHz FM: 87.5–108.0MHz/50kHz (A, G, L models) *3 AM: 530-1710kHz/10kHz FM:87.5-108.0 MHz/100kHz (R model)

✽2

Model Type RDS (Port 70) 0 RX-V595 0 DSP-A595 1 RX-V595RDS Model Type DSP-A(Port 83)

Hi=1, Low=0

010

Always absent (0) Always absent (0) Tuner Mode V1 (✽1) Tuner Mode V2 (✽1) Always absent (0) Always absent (0) Model Type RDS (✽2) Model Type DSP-A (✽2)

■ FACTORY PRESET

All the settings of the system are initialized on shipping. The settings are as follows.

●

INPUT (VIDEO)

DVD/LD (DVD/LD)

●

EFFECT LEVEL

EFFECT CHANNEL PRESET VALUE

CENTER 0 dB RIGHT SURROUND 0 dB LEFT SURROUND 0 dB SUB WOOFER 0 dB

●

DSP PROGRAM

INPUT DSP PROGRAM DELAY PRESET VALUE

CD PRO LOGIC 20ms TUNER ENHANCED 20ms TAPE/MD MOVIE THEATER 20ms DVD/LD MONO MOVIE 49ms TV/DBS TV SPORTS 9ms VCR DISCO 40ms PHONO ROCK CONCERT 16ms V-AUX CONCERT HALL 44ms

●

SET MENU

No. SET MENU PRESET VALUE

8. CENTER DELAY 0 ms

7. DYNAMIC RANGE MAX

6. LFE LEVEL 0 dB

1. CENTER SPEAKER LARGE

2. REAR SPEAKER LARGE

3. MAIN SPEAKER LARGE

4. LFE/BASS OUT SW (SUBWOOFER)

5. MAIN LEVEL NRML (NORMAL)

9. MEMORY GUARD OFF

10. INPUT MODE (TV/DBS) AUTO

●

PRESET STATIONS

STATION FM FACTORY PRESET DATA (MHz)

PAGE NO. U, C R, L, G, A, B

1 87.5 87.5 2 90.1 90.1 3 95.1 95.1

A/C/E 4 98.1 98.1

5 107.9 108.0 6 88.1 88.1 7 106.1 106.1 8 107.9 108.0

STATION AM FACTORY PRESET DATA (kHz)

PAGE NO. U, C, R R, L, G, A, B

1 630 630 2 1080 1080 3 1440 1440

B/D 4 530 531

5 1710 1611 6 900 900 7 1350 1350 8 1400 1404

RX-V595/R-V905/RX-V595RDS

+ 49 hidden pages

Yamaha RXV-595-RDS Service manual

Specifications and Main Features

Frequently Asked Questions

User Manual

n CONTENTS

■ TO SERVICE PERSONNEL

■ REMOTE CONTROL PANELS

■ FRONT PANELS

■ REAR PANELS

■ SPECIFICATIONS

●DIMENSIONS

■ INTERNAL VIEW

■ DISASSEMBLY PROCEDURES

■ SELF DIAGNOSIS FUNCTION

■ FACTORY PRESET