Yamaha RX-V595ARDS User Manual
RX-V595aRDS
Natural Sound AV Receiver
Ampli-Tuner audio-vidéo
B G
OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
BRUKSANVISNING
MANUALE DI ISTRUZIONI
MANUAL DE INSTRUCCIONES
GEBRUIKSAANWIJZING
SUPPLIED ACCESSORIES
ACCESSOIRES FOURNIS
MITGELIEFERTE ZUBEHÖRTEILE
MEDFÖLJANDE TILLBEHÖR
ACCESSORI IN DOTAZIONE
ACCESORIOS INCLUIDOS
BIJGELEVERDE ACCESSOIRES
• After unpacking, check that the following parts are included.
• Après le déballage, vérifier que les pièces suivantes sont incluses.
• Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind.
• Kontrollera efter uppackningen att följande delar finns med.
Verificare che tutte le parti seguenti siano contenute nell’imballaggio dell’apparecchio.
•
• Desembalar el aparato y verificar que los siguientes accesorios están en la caja.
• Controleer na het uitpakken of de volgende onderdelen voorhanden zijn.
• Indoor FM Antenna
• Antenne FM intérieure
• UKW-Innenantenne
• Inomhus-FM-antenn
• Antenna FM interna
• Antena FM interior
• FM-binnenantenne
• AM Loop Antenna
• Cadre-antenne AM
• MW-Rahmenantenne
• AM-ramantenn
• Antenna AM ad anello
• Antena de cuadro de AM
• AM-raamantenne
• 75-ohm/300-ohm antenna adapter (U.K. model only)
• Adaptateur d’antenne 75 ohms/300 ohms
(Modèle Royaume-Uni seulement)
• 75-Ohm/300-Ohm Antennenstecker
(nur Großbritannien-Modell)
• 75 ohm/300 ohm antennadapter
(gäller endast modellen för Storbritannien)
• Adattatore per antenna da 75/300 ohm
(Soltanto il modello per la Gran Bretagna)
• Adaptador de antena de 75-ohmios/300-ohmios
(Sólo el modelo para el Reino Unido)
• 75 ohm/300 ohm antenneadapter
(Alleen modellen voor Verenigd Koninkrijk)
• Remote control
Before using the remote control, install the supplied
batteries. See page 49 for battery installation.
• Télécommande
Avant d’utiliser la télécommande, mettre les piles fournies en
place. Pour la mise en place des piles, voir page 101.
• Fernbedienung
Legen Sie vor Gebrauch der Fernbedienung die
mitgelieferten Batterien ein. Angaben zum Einlegen der
Batterien finden Sie auf Seite 155.
• Fjärrkontroll
Sätt i de medföljande batterierna innan du använder
fjärrkontrollen. Se sidan 207 om hur man sätter i dem.
• Telecomando
Prima di usare il telecomando, installare le batterie in
dotazione. Per l’installazione delle batterie vedere a
pagina 259.
• Control remoto
Antes de utilizar el transmisor de control remoto, instálele
las pilas suministradas. Para instalar las pilas, consulte la
página 311.
• Afstandsbediening
Alvorens u de afstandsbediening gaat gebruiken, moet u de
bijgeleverde batterijen plaatsen. Zie blz. 363 voor het
plaatsen van de batterijen.
• Batteries (size AA, R6, UM-3)
• Piles (taille AA, R6, UM-3)
• Batterien (Größe AA, R6, UM-3)
• Batterier (storlek AA, R6, UM-3)
• Batterie (formato AA, R6, UM-3)
• Pilas (tamaño AA, R6, UM-3)
• Batterijen (maat AA, R6, UM-3)
2
FEATURES
English
5-Channel Power Amplification
Mininum RMS Output
(0.04% THD, 20 Hz – 20 kHz)
Main: 65 W + 65 W (8 Ω)
Center: 65 W (8 Ω)
Rear: 65 W + 65 W (8 Ω)
Multi-mode Digital Sound Field Processing
● Digital Sound Field Processor (DSP)
● Dolby Digital Decoder
● Dolby Pro Logic Decoder
● DTS Decoder
● CINEMA DSP: Theater-like Sound
Experience by the Combination of
YAMAHA DSP Technology and Dolby
Digital, Dolby Pro Logic or DTS
● Automatic Input Balance Control for
Dolby Pro Logic decoding
● Test Tone Generator for Easier Speaker
Balance Adjustment
● Speaker Output Mode Selection
Sophisticated FM/AM Tuner
● 40-Station Random Access Preset Tuning
● Automatic Preset Tuning
● Preset Station Shifting Capability
(Preset Editing)
● 6-Channel External Decoder Input for
Other Future Formats
● Video Signal Input/Output Capability
(Including S Video Connections)
● SLEEP Timer
● Universal Remote Control with Preset
Manufacturer Codes
CONTENTS
SUPPLIED ACCESSORIES........................................... 2
FEA TURES .................................................................... 3
CAUTION ....................................................................... 4
●Introduction
FEATURES OF THE SOUND EFFECTS....................... 5
CONTROLS AND THEIR FUNCTIONS ......................... 8
●Preparation
SPEAKER SETUP ....................................................... 11
CONNECTIONS........................................................... 12
ADJUSTMENTS BEFORE USING THIS UNIT............ 19
●Basic Operation
BASIC OPERATION .................................................... 24
TUNING .......................................................................28
RECEIVING RDS STATIONS ......................................33
SETTING THE SLEEP TIMER..................................... 36
●Information about DSP
SOUND FIELD PROGRAM .........................................37
●Advanced Information
ADJUSTMENTS IN THE “SET MENU” MODE ............ 42
●Remote control
REMOTE CONTROL ...................................................44
SETUP CODES ........................................................... 50
TROUBLESHOOTING ................................................. 51
SPECIFICA TIONS .......................................................54
LIST OF MANUFACTURERS’ CODES ...................... 369
3
CAUTION: READ THIS BEFORE OPERATING YOUR UNIT.
1. To assure the finest performance, please read this manual
carefully. Keep it in a safe place for future reference.
2. Install this unit in a cool, dry, clean place – away from
windows, heat sources, sources of excessive vibration,
dust, moisture and cold. Avoid sources of humming
(transformers, motors). To prevent fire or electrical shock,
do not expose the unit to rain or water.
3. Never open the cabinet. If something drops into the set,
contact your dealer.
4. Do not use force on switches, controls or connection wires.
When moving the unit, first disconnect the power plug and
the wires connected to other equipment. Never pull the
wires themselves.
5. The openings on the cover assure proper ventilation of the
unit. If these openings are obstructed, the temperature
inside the unit will rise rapidly. Therefore, avoid placing
objects against these openings, and install the unit in a
well-ventilated area to prevent fire and damage.
Be sure to allow a space of at least 20 cm behind, 20 cm
on both sides and 30 cm above the top panel of the unit to
prevent fire and damage.
6. The voltage used must be the same as that specified on
this unit. Using this unit with a higher voltage than
specified is dangerous and may result in fire or other
accidents. YAMAHA will not be held responsible for any
damage resulting from the use of this unit with a voltage
other than that specified.
7. Digital signals generated by this unit may interfere with
other equipment such as tuners, receivers and TVs. Move
this unit farther away from such equipment if interference is
observed.
8. Always set the VOLUME control to “
audio source play. Increase the volume gradually to an
appropriate level after playback has been started.
9. Do not attempt to clean the unit with chemical solvents; this
might damage the finish. Use a clean, dry cloth.
10. Be sure to read the “TROUBLESHOOTING” section
regarding common operating errors before concluding that
the unit is faulty.
11. When not planning to use this unit for a long period of time
(e.g., a vacation), disconnect the AC power plug from the
wall outlet.
12. To prevent lightning damage, disconnect the AC power
plug and disconnect the antenna cable when there is an
electrical storm.
13. Grounding or polarization – Precautions should be taken so
that the grounding or polarization of the unit is not
defeated.
14. AC outlet
Do not connect audio equipment to the AC outlet on the
rear panel if that equipment requires more power than the
outlet is rated to provide.
” before starting the
This unit is not disconnected from the AC power source as
long as it is connected to the wall outlet, even if this unit
itself is turned off. This state is called the standby mode. In
this state, this unit is designed to consume a very small
quantity of power.
For U.K. customers
If the socket outlets in the home are not suitable for the plug
supplied with this appliance, it should be cut off and an
appropriate 3 pin plug fitted. For details, refer to the instructions
described below.
Note: The plug severed from the mains lead must be
destroyed, as a plug with bared flexible cord is hazardous if
engaged in a live socket outlet.
Special Instructions for U.K. Model
IMPORTANT
THE WIRES IN MAINS LEAD ARE COLOURED IN
ACCORDANCE WITH THE FOLLOWING CODE:
Blue: NEUTRAL
Brown: LIVE
As the colours of the wires in the mains lead of this
apparatus may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the
terminal which is marked with the letter N or coloured
BLACK. The wire which is coloured BROWN must be
connected to the terminal which is marked with the letter L or
coloured RED.
Making sure that neither core is connected to the earth
terminal of the three pin plug.
4
Introduction
English
FEATURES OF THE SOUND EFFECTS
Welcome to the exciting world of digital home entertainment.
This unit is one of the most complete and advanced AV
receivers available. Some of the more advanced features may
not be familiar to you, but they are easy to use. State-of-the-art
technologies such as Dolby Digital and Digital Theater Systems
(DTS) may be new to your home, but you have probably
experienced the amazing realism they bring to feature films in
theaters around the world.
Digital Sound Field Processing
What is it that makes live music so good? Today’s advanced
sound reproduction technology lets you get extremely close to
the sound of a live performance, but the chances are that you’ll
still notice something missing — the acoustic environment of
the live concert hall. Extensive research into the exact nature
of the sonic reflections that create the ambience of a large hall
has made it possible for YAMAHA engineers to bring you this
same sound to your listening room, so you’ll feel all the sound
of a live concert.
To make the listening experience even more enjoyable, this unit
includes a number of exclusive, digitally created listening
environments known as digital sound fields. Choosing a sound
field program is like transporting yourself to such venues as an
outdoor arena, a European church, or a cozy jazz club. Take
some time now to read more about these features and enjoy
the new experiences this unit brings to your home theater.
Furthermore, our technicians, armed with sophisticated
measuring equipment, have even made it possible to capture
the acoustics of a variety of actual concert halls, theaters, etc.
from around the world, to allow you to accurately re-create any
one of these live performance environments, all in your own
home.
Dolby Pro Logic
Dolby Surround has been used in movie theaters since the midseventies. It has also been available in home entertainment
systems since the late eighties and continues to be a popular
format for home theater systems. It uses four discrete channels
and five speakers to reproduce realistic and dynamic sound
effects: two main channels (left and right), a center channel for
dialog, and a rear channel for special sound effects. The rear
channel reproduces sound within a narrow frequency range.
Most video tapes and laser discs include Dolby Surround
encoding, as do many TV and cable broadcasts. The Dolby Pro
Logic decoder built into this unit employs a digital signal
processing system that stabilizes each channel for even more
accurate sound positioning than is available with standard
analog processors.
5
Dolby Digital
Dolby Digital is the next level of the Dolby Surround sound
system that was developed for 35 mm-film movies by
employing low bit-rate audio coding.
Dolby Digital is a digital surround sound system that provides
completely independent multi-channel audio to you. Dolby
Digital provides five full-range channels in what is sometimes
referred to as a “3/2” configuration: three front channels (left,
center and right), and two surround channels. A sixth bass-only
effect channel is also provided for output of LFE (low frequency
effect), or low bass effects that are independent of other
channels. (This is called the “LFE channel”.) This channel is
counted as 0.1, thus giving rise to the term 5.1 channels in
total.
Compared to Dolby Surround, which is referred to a “3/1”
system (left front, center, right front and just one surround
channel), Dolby Digital features two surround channels, called
stereo or split surrounds, each offering the same full-range
fidelity as the three front channels.
By using the built-in Dolby Digital decoder, you can experience
the dramatic realism and impact of Dolby Digital theater sound
in your home.
The wide dynamic range of sound reproduced by the five fullrange channels and precise sound orientation by digital sound
processing provides listeners with excitement and realism that
have never been experienced before.
Dolby Digital forms 5.1 channels as already mentioned, but it
can also form fewer channels, for example 2-channel stereo
and monaural. You may be able to find some 2-channel stereo
and/or monaural sources encoded with Dolby Digital in the
market.
Laser disc and DVD are home audio/video program sources
that could benefit from Dolby Digital. In the near future, Dolby
Digital will also be applied to DBS, CATV and HDTV. The
ongoing release of Dolby Digital theatrical films now underway
will provide an immediate source of Dolby Digital encoded
video software.
Manufactured under license from Dolby Laboratories. “Dolby”,
“Pro Logic” and the double-D symbol are trademarks of Dolby
Laboratories.
DTS Digital Surround
DTS (Digital Theater Systems) was developed to replace
analog soundtracks of movies with six discrete channels of
digital soundtracks, and it is now installed in many theaters
around the world. The DTS digital playback system changed
the way we experienced movies in theaters with six discrete
channels of superb digital audio.
DTS technology, through intense research and development
has made it possible to deliver similar encode/decode discrete
technology to home audio surround-sound entertainment.
DTS Digital Surround is an encode/decode system which
delivers six channels of master-quality, 20-bit audio; technically,
it is 5.1 channels, which means 5 full-range (left, center, right
and two surround) channels, plus a subwoofer (LFE) channel
(as “0.1”). It is compatible with the 5.1 speaker configurations
that are currently available for home theater systems.
The DTS Digital Surround algorithm is designed to encode the
six channels of 20-bit audio on to some laser discs, compact
discs and DVDs with considerably less data compression.
By using the DTS decoder built into this unit, you can
experience the dramatic realism and impact of the DTSinstalled theater’s high quality sound in your home.
Laser disc, compact disc and DVD are home audio formats by
which DTS can present its high-quality multi-channel audio. (In
addition to movies on laser discs, many exciting new multichannel music recordings will also become available in the
form of DTS-encoded compact discs.)
Manufactured under license from Digital Theater Systems, Inc.
US Pat. No. 5,451,942 and other world-wide patents issued
and pending. “DTS”, “DTS Digital Surround”, are trademarks of
Digital Theater Systems, Inc. Copyright 1996 Digital Theater
Systems, Inc. All Rights Reserved.
6
CINEMA DSP: Dolby Surround + DSP / DTS + DSP
English
The Dolby Surround sound and DTS systems show their full
ability in a large movie theater, because movie sounds are
originally designed to be reproduced in a large movie theater
that uses a multitude of speakers. Trying to create a sound
environment similar to that of a movie theater in your home is
difficult because of the room size, material inside the walls, the
number of speakers, and so on. In other words, your listening
room is very different from a movie theater.
Dolby Pro Logic + 2 Digital Sound Fields
Digital sound fields are created on the presence side and the
rear surround side of the Dolby Pro Logic-decoded sound
field, respectively. They create a wide acoustic environment
and emphasize the surround effect in the room, letting you
feel as much presence as if you were watching a movie in a
popular Dolby Stereo theater.
Refer to pages 37 to 38 for the DSP program.
However, YAMAHA DSP technology allows you to create nearly
the same sound experience as that of a large movie theater in
your home by compensating for the lack of presence and
dynamics in the listening room with original digital sound fields
combined with Dolby Surround or DTS Digital Surround
sounds.
CINEMA DSP
The YAMAHA “CINEMA DSP” logo indicates those programs
that are created by the combination of YAMAHA DSP
technology and Dolby Surround or DTS.
Dolby Digital or DTS + 3 Digital Sound Fields
Digital sound fields are created on the presence side and the
independent left and right surround sides of the Dolby Digitaldecoded or DTS-decoded sound field, respectively. They
create a wide acoustic environment and strong surround
effect in the room without losing high-channel separation. With
the wide dynamic range of Dolby Digital or DTS sound, this
sound field combination lets you feel as if you were watching
a movie in the newest Dolby Digital theater or DTS-installed
theater. This is the most ideal home theater sound at the
present time.
Refer to pages 37 to 38 for the DSP program.
7
CONTROLS AND THEIR FUNCTIONS
FRONT PANEL
NATURAL SOUND AV RECEIVER
STANDBY/ON
PHONES
A/B/C/D/E1 2
SPEAKERS
A
B
ON OFF
3
5
4
0
1
2
3
4
1
1
2
2
3
3
4
4
55
678
0
1
2
2
3
3
4
4
55
Refer to pages 44 to 49 for the remote control.
STANDBY/ON
1
Press this switch to turn on the power of this unit. Press it
again to set this unit in the standby mode.
Standby mode
In this state, this unit consumes a very small quantity of
power to receive infrared-signals from the remote control.
2 Remote control sensor
This receives signals from the remote control.
3 Display
This shows various information. (Refer to page 10 for details.)
4 MEMORY (MAN’L/AUTO FM)
Press this button to store the broadcasting stations.
When this button is pressed and held for more than three
seconds, automatic preset tuning begins.
5 EDIT
This button is used to exchange the assigment of two preset
stations with each other.
CINEMA DSP
MEMORY EDIT
MAN’L/AUTO FM AUTO/MAN’L MONO
BALANCETREBLEBASS
0
1
1
2
3
4
5 RL 5
6 TUNING MODE (AUTO/MAN’L MONO)
Press this button to switch the tuning mode to automatic or
manual. To select the automatic tuning mode, press this button
so that the “AUTO TUNING” indicator lights up on the display.
To select the manual tuning mode, press this button so that the
“AUTO TUNING” indicator goes off.
7 FM/AM
Press this button to switch the reception band between FM and
AM.
8 TUNING UP/DOWN
This button is used for tuning. Press the UP side to tune in to
higher frequencies, and press the DOWN side to tune in to
lower frequencies.
When this unit is in the PTY SEEK mode, press this button to
change the currently selected program type.
9 TAPE/MD MON / EXT. DECODER
Press this button to play a tape or an MD. The “TAPE/MD
MON” indicator lights up on the display.
When you press the button next, the “TAPE/MD MON” indicator
goes off, “EXT. DECDR” appears on the display and you can
play the signal connected to the EXTERNAL DECODER
INPUT terminals.
TUNING
MODE
RDS
MODE
PTY SEEK
MODE
FM/AM
EON
START
TAPE/MD MON
/EXT. DECODER
DOWN
TUNING
TIME/
SET
LEVEL
MENU
INPUT
VCR • V–AUX • TV/DBS • DVD/LD • CD • TUNER • PHONO
UP
INPUT MODE
EFFECT
PROGRAM
8 VIDEO VIDEO
VOLUME
18
12
20
22
40
80
VIDEO AUX
8
4
2
0
–dB
AUDIO R
L
0 INPUT
Turn this selector to select the input source (VCR, VIDEO AUX,
TV/DBS, DVD/LD, CD, TUNER, PHONO) that you want to
listen to or watch.
The name of the selected input source appears on the display.
8
English
q INPUT MODE
This button switches between the DVD/LD and TV/DBS input
signal modes.
w VOLUME
This control is used to raise or lower the volume level.
e PHONES jack
When you use headphones, connect the headphones to the
PHONES jack. You can listen to the sound to be output from
the main speakers through the headphones.
When using headphones only , set both SPEAKERS A and B to
the OFF position and switch off the digital sound field processor
(so that no DSP program name appears on the display) by
pressing EFFECT.
r SPEAKERS
Set A or B (or both A and B) to the ON position for the main
speaker system (connected to this unit) that you want to use.
Set the button(s) for the main speaker system you don’t want to
use to the OFF position.
t A/B/C/D/E
Press this button to select one of a group (A to E) of preset
stations.
y Preset station number selector
Each of these buttons selects a preset station number (1 to 8).
o RDS MODE
When an RDS station is received, pressing this button changes
the display mode into the PS mode, PTY mode, RT mode and/
or CT mode (if the station employs those RDS data services) in
turn.
p PTY SEEK MODE
When this button is pressed, the unit is set in the PTY SEEK
mode.
a PTY SEEK START
Press this button to begin searching for a station after the
desired program type has been selected in the PTY SEEK
mode.
s EON
Press this button to select the desired program type (NEWS,
INFO, AFFAIRS, SPORT) when you want to call a radio
program of that type automatically.
d TIME/LEVEL
Press this button to select the item in the TIME/LEVEL mode.
f +/–
These buttons are used to adjust the settings of the SET MENU
mode and the TIME/LEVEL mode. In the TIME/LEVEL mode,
press + to increase the delay time or speaker output level.
Press – to decrease the delay time or speaker output level.
u Tone controls
These controls are only effective for the sound from the main
speakers.
BASS
Use this control to increase or decrease the low-frequency
response. The “0” position produces a flat response.
TREBLE
Use this control to increase or decrease the high-frequency
response. The “0” position produces a flat response.
i BALANCE
This control is only effective for the sound from the main
speakers.
Turn the control to adjust the balance of the output volume to
the left and right speakers to compensate for sound imbalance
caused by the speaker location or listening room conditions.
g SET MENU
Press this button to select functions in the SET MENU mode.
h PROGRAM selector
Press
The name of the selected program appears on the display.
or to select a DSP program.
j EFFECT
Press this button once to switch the effect speakers (center and
rear) on or off. If you turn off the effect by using EFFECT, all
Dolby Digital and DTS audio signals are directed to the main
left and right channels. In that case, the left and right channel
signal levels may not match.
k VIDEO AUX terminals
Connect an auxiliary video or audio input source such as a
camcorder to these terminals. If the connected video unit has
an S video output terminal, connect it to the S VIDEO terminal
to obtain a high-resolution picture. The source connected to
these terminals can be selected by INPUT.
9
Loading...