Yamaha RX-V573, RX-V473 User Manual
AV Receiver/Receptor AV
RLH
English
Español
Easy Setup Guide
Guía de configuración sencilla
1 Preparation
AV Receiver
Easy Setup Guide
English
This document explains how to set up a 5.1- or 7.1-channel system (RX-V573
only) and play back surround sound from a BD/DVD on the unit.
Accessories
Check that the following accessories are supplied with the product.
Remote control Batteries
AM antenna FM antenna YPAO microphone
CD-ROM
(Owner’s Manual)
• The illustrations of the main unit and remote control used in this guide are of the RX-V573 (U.S.A.
model), unless otherwise specified.
(AAA, R03, UM-4) (x2)
Insert the batteries the right way round.
*The supplied FM antenna
varies depending on the
region of purchase.
Safety Brochure Easy Setup Guide
To reduce the impact on natural resources, the Owner’s Manual for this product is
supplied on CD-ROM. For more information about this product, refer to the
Owner’s Manual on the supplied CD-ROM.
PDF versions of this guide and “Owner’s Manual” can be downloaded from the
following website.
http://download.yamaha.com/
Cables required for connections
The following cables (not supplied) are required to build the system described in this
document.
• Speaker cables (depending on the number of speakers)
• HDMI cable (x2)
• Audio pin cable (x1)
• Digital optical cable (x1)
(not required if your TV supports ARC [Audio Return Channel])
En 1
2 Placing speakers
Set up the speakers in the room using the following diagram as a reference.
For information on other speaker systems, refer to “Owner’s Manual”.
5.1-channel system
45
12
39
10° to 30°10° to 30°
7.1-channel system
(RX-V573 only)
1
39
45
10° to 30° 10° to 30°
67
30 cm (1 ft) or more
1 Front speaker (L)
2 Front speaker (R)
3 Center speaker
4 Surround speaker (L)
5 Surround speaker (R)
6 Surround back speaker (L)
7 Surround back speaker (R)
9 Subwoofer
2
2 En2 En
3 Connecting speakers/subwoofer
FRONT
FRONT
FRONT CENTER SURROUND
B
Y
SUBWOOFER
SPEAKERS
FRONT CENTER SURROUND
B
Y
SUBWOOFER
SPEAKERS
• (U.S.A. and Canada models only)
Under its default settings, the unit is configured for 8-ohm
speakers. When connecting 6-ohm speakers, set the unit’s
speaker impedance to “6 Ω MIN”. For details, see “Setting the
speaker impedance” in “Owner’s Manual”.
• (Except for U.S.A. and Canada models)
Use speakers with an impedance of at least 6 Ω.
• Use a subwoofer equipped with built-in amplifier.
• Before connecting the speakers, remove the unit’s power cable
from the AC wall outlet and turn off the subwoofer.
• Ensure that the core wires of the speaker cable do not touch
each other or come into contact with the unit’s metal areas. This
may damage the unit or the speakers. If the speaker cables
short circuit, “Check SP Wires” will appear on the front display
when the unit is turned on.
■ Connecting speaker cables
Speaker cables have two wires. One is for connecting the
negative (–) terminals of the unit and the speaker, and the
other is for the positive (+) terminals. If the wires are
colored to prevent confusion, connect the black wire to
the negative and the other wire to the positive terminals.
a Remove approximately 10
mm (3/8”) of insulation
+ (red)
from the ends of the
speaker cable and twist
the bare wires of the cable
firmly together.
– (black)
b Loosen the speaker terminal.
c Insert the bare wires of the cable into the gap on the side
(upper right or bottom left) of the terminal.
d Tighten the terminal.
b
c
d
aa
Connect the front speakers (1/2)
1
2
to the FRONT (//\) terminals.
The unit (rear)
12
9
45
3
Connect the center speaker (3) to the
CENTER terminal.
The unit (rear)
12
9
45
3
Using a banana plug
(U.S.A., Canada, China,
Australia and General
Banana plug
models only)
a Tighten the speaker
terminal.
b Insert a banana plug into the end of the terminal.
a
b
En 3
Connect the surround speakers (4/
FRONT CENTER SURROUND
B
Y
SUBWOOFER
SPEAKERS
FRONT CENTER SURROUND
B
Y
SUBWOOFER
SPEAKERS
FRONT CENTER SURROUND
SINGLE
SURROUND BACK/BI AMP
/ZONE B
B
Y
SUBWOOFER
SPEAKERS
3
5) to the SURROUND (//\)
terminals.
Connect the subwoofer (9) to the
4
SUBWOOFER jack.
For 7.1-channel system (RX-V573 only)
Connect the surround back speakers (6/
7) to the SURROUND BACK (//\)
terminals.
The unit (rear)
The unit (rear)
Audio pin cable
12
9
45
3
9
45
12
3
The unit (rear)
1
9
2
3
45
67
4 En
4 Connecting external devices
jack
O
P
P
Y
COMPONENT
HDMI
R
B
VIDEO
OPTICAL COAXIAL COAXIAL OPTICAL
AV 1
TV
b
HDMI HDMI
ARC
AV
HDMI 1
(
OUT
BD/DVD
HDMI 1
(
)
OUT
HDMI
BD/DVD
ARC
AM
OPTICAL
(TV)
VIDEO
AV 4
(
)
TV
2
AV 5
AV 3
AV 4
HDMI in HDMI out
HDMIOPTICAL
HDMI
HDMI 1 jack
)
HDMI 2
ANTENNA
AV 6
HDMI 4
HDMI 3
FM
COMPONENT
VIDEO
R
P
P
B
Y
MONITOR OUT
AV
SUBWOOFER
OUT
AUDIO
The unit (rear)
HDMI
HDMI
a
NETWORK
FRONT CENTER SURROUND
Audio out
(optical)
O
c
AV 4 (OPTICAL) jack
HDMI OUT
SPEAKERS
BD/DVD player
VOLTAGE
SELECTOR
SURROUND BACK/BI AMP
/ZONE B
SINGLE
VOLTAGE SELECTOR
(General model only)
-
110V
120V
-
220V
240V
d
To an AC wall
outlet
Before connecting the power cable (General model only)
Make sure you set the switch position of
VOLTAGE SELECTOR according to your local voltage.
Voltages are AC 110-120/220-240 V, 50/60 Hz.
Connect external devices to the unit.
1
a Connect a BD/DVD player to the unit with an HDMI
cable.
If the BD/DVD player is currently connected to the
TV directly with an HDMI cable, disconnect the
cable from the TV and connect it to this unit.
b Connect a TV to the unit with the other HDMI cable.
c Connect a TV to the unit with a digital optical cable.
This connection is required to play back TV audio
on the unit. This connection is not required if your
TV supports ARC (Audio Return Channel).
d Connect the power cable to an AC wall outlet.
• For information on how to connect radio antennas or other
external devices, see “PREPARATIONS” in “Owner’s Manual”.
Turn on the unit, the TV and the BD/DVD
2
player.
Use the TV remote control to change the
3
TV input to video from the unit.
The connections are complete. Proceed to the next
page to optimize the speaker settings.
Turn on the unit
YPAO MIC
PHONES
SILENT
CINEMA
MEMORY
PRESET
INFO
BD
DVD
CONTROL
TONE
INPUT
FM AM
SCENE
TV
NET
PROGRAM
STRAIGHT
TUNING
RADIO
AUX USB
VIDEO
VIDEO
iPod/iPhone/iPad
AUDIO
5V 2.1A
VOLUME
DIRECT
• By connecting a TV to the unit with an HDMI cable, you can
configure the unit’s settings with the menu displayed on the TV. In
addition, you can select the on-screen menu language from English
(default), French, German, Spanish, Russian and Chinese. For
details, refer to “Owner’s Manual”. In this guide, illustrations of
English menu screens are used as examples.
The unit (front)
En 5
Loading...