Natural Sound Stereo Receiver/Natural Sound Compact Disc Player
Récepteur Stéréo/Lecteur Compact Disque
RL
OWNER’S MANUAL
MODE D’EMPLOI
SAFETY INSTRUCTIONS
6A A unit and cart combination should be
CAUTION
RISK OF ELECTRIC SHOCK
DO␣ NOT OPEN
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
• Explanation of Graphical Symbols
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert you to the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient
magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert you to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS UNIT TO RAIN
OR MOISTURE.
IMPORTANT!
Please record the serial number of this unit in the space
below.
Model:
Serial No.:
The serial number is located on the rear of the unit.
Retain this Owner’s Manual in a safe place for future
reference.
1Read Instructions – All the safety and operating
instructions should be read before the unit is operated.
2Retain Instructions – The safety and operating
instructions should be retained for future reference.
3Heed Warnings – All warnings on the unit and in the
operating instructions should be adhered to.
4Follow Instructions – All operating and other
instructions should be followed.
5Water and Moisture – The unit should not be used near
water – for example, near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a
swimming pool, etc.
6Carts and Stands – The unit should be used only with a
cart or stand that is recommended by the manufacturer.
moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the unit and cart combination
to overturn.
7Wall or Ceiling Mounting – The unit should be mounted
to a wall or ceiling only as recommended by the
manufacturer.
8Ventilation – The unit should be situated so that its
location or position does not interfere with its proper
ventilation. For example, the unit should not be situated
on a bed, sofa, rug, or similar surface, that may block
the ventilation openings; or placed in a built-in
installation, such as a bookcase or cabinet that may
impede the flow of air through the ventilation openings.
9Heat – The unit should be situated away from heat
sources such as radiators, stoves, or other appliances
that produce heat.
10 Power Sources – The unit should be connected to a
power supply only of the type described in the operating
instructions or as marked on the unit.
11 Power-Cord Protection – Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying
particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the unit.
12 Cleaning – The unit should be cleaned only as
recommended by the manufacturer.
13 Nonuse Periods – The power cord of the unit should be
unplugged from the outlet when left unused for a long
period of time.
14 Object and Liquid Entry – Care should be taken so that
objects do not fall into and liquids are not spilled into
the inside of the unit.
15 Damage Requiring Service – The unit should be
serviced by qualified service personnel when:
A. The power-supply cord or the plug has been
B. Objects have fallen, or liquid has been spilled into
C. The unit has been exposed to rain; or
D. The unit does not appear to operate normally or
E. The unit has been dropped, or the cabinet damaged.
16 Servicing – The user should not attempt to service the
unit beyond those means described in the operating
instructions. All other servicing should be referred to
qualified service personnel.
17 Power Lines – An outdoor antenna should be located
away from power lines.
18 Grounding or Polarization – Precautions should be
taken so that the grounding or polarization is not
defeated.
damaged; or
the unit; or
exhibits a marked change in performance; or
2
19 For U.S. customers only:
Outdoor Antenna Grounding – If an outside antenna is
connected to this unit, be sure the antenna system is
grounded so as to provide some protection against
voltage surges and built-up static charges. article 810 of
the National Electrical Code, ANSI/NFPA 70, provides
information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire
to an antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding
electrode.
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in
particular, specifies that the cable ground shall be
connected to the grounding systerm of the building, as
close to the point of cable entry as practical.
FCC INFORMATION (for US customers only)
EXAMPLE OF ANTENNA GROUNDING
MAST
GROUND
CLAMP
ELECTRIC
SERVICE
EQUIPMENT
NEC
– NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN
WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810–20)
GROUNDING CONDUCTORS
(NEC SECTION 810–21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250. PART H)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS
UNIT!
This product, when installed as indicated in the
instructions contained in this manual, meets FCC
requirements. Modifications not expressly approved by
Yamaha may void your authority, granted by the FCC, to
use the product.
2. IMPORTANT: When connecting this product to
accessories and/or another product use only high quality
shielded cables. Cable/s supplied with this product
MUST be used. Follow all installation instructions.
Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply
with the requirements listed in FCC Regulations, Part 15
for Class “B” digital devices. Compliance with these
requirements provides a reasonable level of assurance
that your use of this product in a residential environment
will not result in harmful interference with other
electronic devices.
This equipment generates/uses radio frequencies and, if
not installed and used according to the instructions found
in the users manual, may cause interference harmful to
the operation of other electronic devices.
We Want You Listening For A Lifetime
Compliance with FCC regulations does not guarantee that
interference will not occur in all installations. If this product
is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try
to eliminate the problem by using one of the following
measures:
Relocate either this product or the device that is being
affected by the interference.
Utilize power outlets that are on different branch (circuit
breaker or fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead,
change the lead-in to coaxial type cable.
If these corrective measures do not produce satisfactory
results, please contact the local retailer authorized to
distribute this type of product. If you can not locate the
appropriate retailer, please contact Yamaha Electronics
Corp., U.S.A. 6660 Orangethorpe Ave, Buena Park, CA
90620.
The above statements apply ONLY to those products
distributed by Yamaha Corporation of America or its
subsidiaries.
YAMAHA and the Electronic Industries Association’s Consumer Electronics Group want you to get the most out of your
equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or
distortion – and, most importantly, without affecting your sensitive hearing. Since hearing damage from loud sounds is
often undetectable until it is too late, YAMAHA and the Electronic Industries Association’s Consumer
Electronics Group recommend you to avoid prolonged exposure from excessive volume levels.
3
SUPPLIED ACCESSORIES• After unpacking, check that the following parts are contained.
ACCESSOIRES FOURNIS• Après le déballage, vérifier que les pièces suivantes sont incluses.
<RX-E100>
• Remote control
• Télécommande
SLEEP
TIME
A
REP
B
RNDM
D
PEAK
MODESTART
VOLUME
TAPE
MDCD
AUX
TUNER
PRESET
MD REC
TAPE
DISP
C
PROG
E
TAPE
TAPE REC
• AM loop antenna
• Antenne cadre AM
• Indoor FM antenna
• Antenne intérieure FM
• Batteries (size AAA, UM-4, R03)
• Piles (format AAA, UM-4, R03)
MODESTART
<CDX-E100>
• RCA Pin Cable
• Câble de raccordement RCA
4
DUBBING
• System Control Cable
• Câble de commande du système
ENGLISH
INTRODUCTION
Thank you for purchasing this YAMAHA product. We hope it will give you many years of trouble-free enjoyment. For the
best performance, read this manual carefully. It will guide you in operating your YAMAHA product.
FEATURES
<RX-E100>
• Minimum RMS Output Power per Channel
40 W + 40 W (6Ω, 20 - 20,000Hz, 0.1% THD)
• Full Operation System Remote Control
• 40-Station FM/AM Preset Tuning
• SUBWOOFER Output Terminal
The receiver (RX-E100) and CD player (CDX-E100) are the main units of the YAMAHA E100 series. You could upgrade
the system by adding the cassette deck (KX-E100) and MD recorder (MDX-E100)*.
*MD recorder (MDX-E100) may not be available for some areas.
•To assure the finest performance, please read this
manual carefully. Keep it in a safe place for future
reference.
•Install your unit in a well ventilated, cool, dry, clean
place – away from windows, heat sources, vibration,
dust, moisture, or cold. To avoid humming sounds,
locate the unit away from other electrical appliances,
motors, and transformers. To prevent fire or electrical
shock, do not expose to rain and water.
•(U.K. and Europe models only)
Be sure to allow at least 10 cm of ventilation space at
the top, on left, right, and back sides of RX-E100.
•Do not operate the unit upside-down. It may overheat,
possibly causing damage.
•Never open the cabinet. If something drops into the set,
contact your dealer.
•Do not use force on switches, knobs or cords.
•Always set the VOLUME control to minimum before
starting playback of an audio source: increase the
volume gradually to an appropriate level after play has
started.
•When not planning to use this unit for long periods of
time (i.e., vacation, etc.), disconnect the AC power plug
from the wall outlet.
•Grounding or polarization – Precautions should be taken
so that the grounding or polarization of the unit is not
defeated.
•Do not clean the unit with chemical solvents; this might
damage the finish. Use a clean, dry cloth.
•Be sure to read the “Troubleshooting” section on
common operating errors before concluding that your
unit is faulty.
•Do not place another component on top of this unit, as
damage or discoloration on the surface of the unit may
result.
•To prevent damage by lightning, disconnect the power
cord from the wall outlet during an electrical storm.
•When disconnecting the power cord from the wall
outlet, grasp the plug; do not pull the cord.
•Do not plug the AC power plug to the wall outlet before
you finish all connections.
•The voltage to be used must be the same as that
specified on this unit. Using this unit with a higher
voltage than that which is specified is dangerous and
may result in a fire or other type of accident causing
damage. YAMAHA will not be held responsible for any
damage resulting from use of this unit with a voltage
other than that which is specified.
•When listening to the receiver at a high volume level for
a long time, the temperature inside the unit rises. To
prevent overheating and possible damage to this unit,
the internal fan starts running.
•Sudden temperature changes and storage or operation in
an extremely humid environment may cause
condensation inside the cabinet.
The unit is not disconnected from the AC power source
as long as it is connected to the wall outlet, even if this
unit itself is turned off. This state is called the standby
mode. In this state, this unit is designed to consume a
very small quantity of power.
CAUTION FOR CARRYING THE UNIT
Before carrying the unit, first remove all discs from
the unit, press STANDBY/ON to turn the unit off,
then disconnect the AC power plug from the wall
outlet.
VOLTAGE SELECTOR (General model
only)
The voltage selector (on the rear panel of this unit)
must be correctly set to the voltage used locally
before making any connection to the AC power
supply.
FREQUENCY STEP switch <General
model only>
Because the interstation frequency spacing differs
in different areas, set the FREQUENCY STEP
switch (located on the rear panel) according to the
frequency spacing in your area.
Before setting this switch, disconnect the AC power
plug of this unit from the AC outlet.
CAUTION
Use of controls or adjustments or performance of
procedures other than those specified herein may
result in hazardous radiation exposure.
As the laser beam used in this compact disc player is
harmful to the eyes, do not attempt to disassemble the
cabinet. Refer servicing to qualified personel only.
For Canadian Customers
To prevent electric shock, match wide blade of plug to
wide slot and fully insert.
Thes Class B digital apparatus complies with
CANADIAN ICES-003
E-2
GETTING STARTED
The remote control
This remote control controls a whole system: not only
RX-E100 but also CDX-E100. Moreover, a cassette deck
(KX-E100) and MD recorder (MDX-E100) that level up
your system can be operated by it. Operating buttons for
each unit are explained on the pages below:
• Use only AAA, UM-4, R03 batteries for replacement.
• Be sure the polarities are correct. (See the illustration inside
the battery compartment.)
• Remove the batteries if the remote control will not be used for
an extended period of time.
• If batteries leak, dispose of them immediately. Avoid touching
the leaked material or letting it come in contact with clothing,
etc. Clean the battery compartment thoroughly before
installing new batteries.
Remote control operation range
NATURAL SOUND STEREO RECEIVER RX-E100
DISPLAY
STANDBY/ON PHONES
Remote control
sensor
MEMORY AUTO/MAN'L
TIME ADJ TIMER
HOURMIN
BASS TREBLE BALANCE
+-+-
VOLUME
PRESET/TUNINGPRESET/BAND
RL
MAXMIN
INPUT
English
2Insert 4 batteries into the battery compartment.
3Replace the battery compartment cover.
Battery replacement
If you find that the remote control must be used closer to
the main unit than usual, the batteries are weak. Replace
batteries with new ones.
Within approximately
6 m (20 feet)
30°
30°
Notes
• There should be no large obstacles between the remote control
and the main unit.
• If the remote control sensor is directly illuminated by strong
lighting (especially an inverter type of fluorescent lamp, etc.),
it might cause the remote control not to work correctly. In this
case, reposition the main unit to avoid direct lighting.
E-3
GETTING STARTED
Connecting the speakers
Never plug the AC power cord to the wall outlet until all connections are completed.
Follow the steps as shown below to connect the system using the supplied cords and accessories.
Right speakerLeft speaker
FM antenna
3
75 Ω UNBAL
FREQUENCY
FM ANT GND AM ANT
STEP
ABE
L
TAPE
R
OUT ININ
L
MD
R
D
C
1 Connect the Speakers.
1 Unscrew the knob.
2 Remove approx. 5 mm (1/4”) of insulation from
each of the speaker wires and insert the bare wire
into the terminal.
3 Tighten the knob to secure the wire.
AM loop antenna
2
6 Ω MIN./SPEAKER
SPEAKERS
1
LR
SYSTEM
SUBWOOFER
CONNETOR
OUT
To wall outlet
4
CD
AUX
3 Connect the FM Antenna.
75 Ω UNBAL
FM ANT
Red: positive(+)
Black: negative(–)
1
2 Connect the AM Antenna.
Set up the AM loop antenna, then connect it.
GND AM ANT
E-4
2
4 Connect the AC power cord to a wall outlet.
• Use external FM/AM antennas if you need better reception.
3
Consult your dealer.
• The AM loop antenna should be placed apart from the main
unit. The antenna may be hung on a wall.
To Connect the Subwoofer (optional)
You can reinforce the bass frequencies by adding a
subwoofer (optional).
Connect the SUBWOOFER OUT terminal of the unit to
the INPUT terminal of the subwoofer.
GETTING STARTED
Connecting the system
Connecting RX-E100 and CDX-E100
1 Connect ‰ to ‰ using the RCA pin cable.
Insert the plugs into the jacks of the same colour.
2 Connect RX-E100 and CDX-E100 with the system control cable.
The other SYSTEM CONNECTOR of CDX-E100 is for connecting MDX-E100 or KX-E100.
3 Connect the AC power plug of CDX-E100 to AC OUTLET of RX-E100.
<CDX-E100>
3
L
R
ANALOG
DIGITAL
OPTICAL
OUT
E
OUT
SYSTEM
CONNECTOR
English
To RX-E100
RCA pin cable
1
FREQUENCY
STEP
L
TAPE
R
OUTININ
L
MD
R
D
75 Ω UNBAL
FM ANTGND AM ANT
ABE
CD
AUX
C
6 Ω MIN./SPEAKER
System control cable
LR
SPEAKERS
SUBWOOFER
OUT
SYSTEM
CONNETOR
<RX-E100>
2
To wall outlet
Adding KX-E100 and MDX-E100 to the above system (For details, refer to the owner's manual
supplied with the respective component.)
1 Connect Å and ı of RX-E100 to Å and ı of KX-E100.
2 Connect Ç and Î of RX-E100 to Ç and Î of MDX-E100.
3 Connect an external component to the AUX terminal of RX-E100.
4 Connect DIGITAL OPTICAL OUT of CDX-E100 to DIGITAL OPTICAL IN of MDX-E100.
Take off the covers of the optical fiber cable plug, the DIGITAL OPTICAL OUT jack, and the DIGITAL OPTICAL
IN jack before making digital connections. Be sure to replace the terminal’s cover when the terminal on the rear panel
is not being used, in order to protect from dust.
5 AC OUTLET (CDX-E100)
Connect the AC power plug of MDX-E100 or KX-E100 (Except for the UK model).
E-5
Loading...
+ 21 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.