Yamaha RX10RTW User Manual

OWNER’S MANUAL
SNOWMOBILE
LIT-12628-02-61
RX10RTW
8GT-28199-10
E_8gt.book Page 1 Tuesday, March 28, 2006 5:37 PM
A
ESU00286
1-
MACHINE IDENTIFICATION
Identification number records
A. FRAME NUMBER:
CZ-01E
B
B. ENGINE NUMBER (PRIMARY ID):
CZ-01E
C. KEY NUMBER:
C
CZ-01E
Record the frame number, engine number (Primary ID), and key number in the spaces provided for assistance when ordering spare parts from a Yamaha dealer.
1
The
frame number
is the seventeen-digit number stamped on the frame of the snowmobile. (See fig.È.)
2
The
engine number
is stamped in the location as
shown. (See fig. É.)
3
Key number
(See fig. Ê.)
Also, record and keep the ID numbers in a separate place in case the snowmobile is stolen.
E_8gt.book Page 1 Tuesday, March 28, 2006 5:37 PM
ESU00011
1-
INTRODUCTION
Congratulations on your purchase of a Yamaha snowmo­bile. This model is the result of Yamaha’s vast experience in the production of fine sporting and touring snowmo­biles. It represents the high degree of craftsmanship and reliability that have made Yamaha a leader in these fields. This manual will give you an understanding of the opera­tion, inspection, and basic maintenance of this snowmo­bile. If you have any questions concerning the operation or maintenance of your snowmobile, please consult a Yamaha dealer. To maintain the high quality and performance of this snowmobile, it is important that you and your Yamaha dealer pay close attention to the recommended mainte­nance schedules and operating instructions contained within this manual.
RX10RTW
OWNER’S MANUAL
©2006 by Yamaha Motor Corporation, U.S.A.
1st Edition, April 2006
All rights reserved.
Any reprinting or unauthorized use
without the written permission of
Yamaha Motor Corporation, U.S.A.
is expressly prohibited.
Printed in Japan
P/N LIT-12628-02-61
E_8gt.book Page 2 Tuesday, March 28, 2006 5:37 PM
@
PLEASE READ AND UNDERSTAND THIS MANUAL COMPLETELY BEFORE OPERATING THE SNOWMO­BILE.
@
NOTE:
@
@
Particularly important information is distinguished in this manual by the following notations.
WARNING
Yamaha continually seeks advancements in product design and quality. Therefore, while this manual con­tains the most current product information available at the time of printing, there may be minor discrepan­cies between your snowmobile and this manual. If there is any question concerning this manual, please consult a Yamaha dealer. This manual should be considered a permanent part of this snowmobile and should remain with the snow­mobile when resold.
The Safety Alert Symbol means ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!
WARNING
@
Failure to follow WARNING instructions could result in severe injury or death to the snowmobile operator, a bystander, or a person inspecting or repairing the snow­mobile.
CAUTION
@
:
A CAUTION indicates special precautions that must be taken to avoid damage to the snowmobile.
NOTE:
@
A NOTE provides key information to make procedures easier or clearer.
E_8gt.book Page 1 Tuesday, March 28, 2006 5:37 PM
ESU00003
CONTENTS
YAMAHA MOTOR CORPORATION, U.S.A. SNOWMOBILE LIMITED WARRANTY
.......................................1-1
YAMAHA EXTENDED SERVICE (Y.E.S.)
...............................................1-4
LOCATION OF THE IMPORTANT LABELS
SAFETY INFORMATION
DESCRIPTION
CONTROL FUNCTIONS
.......................2-1
...................3-1
...................................4-1
....................5-1
Main switch......................................5-1
Throttle lever....................................5-1
Engine overheating prevention
system .............................................5-2
Throttle override system
(T.O.R.S.) ........................................5-2
Speedometer unit ............................5-4
High beam indicator light .................5-5
Fuel meter and grip/thumb warmer
level indicator...................................5-6
Fuel level warning indicator .............5-7
Oil level warning indicator................5-7
Low coolant temperature indicator
light ..................................................5-7
Coolant temperature warning
indicator ...........................................5-8
Self-diagnostic system.....................5-8
Engine stop switch...........................5-9
Brake lever ......................................5-9
Parking brake lever........................5-10
Headlight beam switch ..................5-10
Auxiliary DC jack ...........................5-10
Shroud and covers ........................5-11
Drive guard ....................................5-12
V-belt holders ................................5-12
Storage compartment....................5-12
PRE-OPERATION CHECKS
..............6-1
Fuel .................................................6-1
Engine oil.........................................6-2
Engine oil level ................................6-3
Coolant ............................................6-4
Throttle lever ...................................6-5
Throttle override system
(T.O.R.S.) ........................................6-5
Brake ...............................................6-6
Brake fluid leakage..........................6-7
V-belt ...............................................6-7
Drive guard......................................6-7
Drive track .......................................6-8
Slide runners ...................................6-8
Skis and ski runners ........................6-9
Steering system...............................6-9
Lights...............................................6-9
Air filter ..........................................6-10
Fittings and fasteners ....................6-11
Tool kit and recommended
equipment......................................6-11
OPERATION
......................................7-1
Starting the engine ..........................7-1
Break-in ...........................................7-2
Riding your snowmobile ..................7-3
Getting to know your snowmobile ...7-3 Learning to ride your snowmobile ...7-3
To start out and accelerate..............7-3
Braking ............................................7-3
Turning ............................................7-4
Riding uphill.....................................7-4
Riding downhill ................................7-5
Traversing a slope...........................7-5
Ice or icy surface .............................7-5
Hard-packed snow ..........................7-6
Operation on surfaces other than
snow or ice ......................................7-6
Maximizing drive track life ...............7-7
Driving .............................................7-8
E_8gt.book Page 2 Tuesday, March 28, 2006 5:37 PM
Stopping the engine.........................7-8
Transporting ....................................7-9
PERIODIC MAINTENANCE ...............8-1
Periodic maintenance chart for the
emission control system ..................8-1
General maintenance and
lubrication chart ...............................8-2
Tool kit .............................................8-5
Removing and installing the
shroud and covers ...........................8-5
Checking the spark plugs ................8-7
Adjusting the engine idling speed ....8-9
Adjusting the throttle cable ............8-10
Adjusting the high-altitude
settings ..........................................8-11
Adjusting the valve clearance........8-11
Changing the engine oil.................8-12
Cooling system ..............................8-14
Replacing the V-belt ......................8-16
Checking the drive chain housing oil level and the drive
chain tension .................................8-19
Checking the brake pads...............8-20
Checking the parking brake
pads...............................................8-20
Checking the brake fluid level........8-21
Changing the brake fluid................8-22
Suspension....................................8-22
Adjusting the drive track ................8-28
Aligning the skis.............................8-30
Lubrication .....................................8-31
Replacing a headlight bulb ............8-32
Adjusting the headlight beams ......8-33
Battery ...........................................8-33
Replacing a fuse............................8-34
Electric...........................................11-3
WIRING DIAGRAM ..........................12-1
TROUBLESHOOTING .......................9-1
STORAGE ........................................10-1
SPECIFICATIONS............................11-1
Dimensions....................................11-1
Engine ...........................................11-1
Chassis..........................................11-2
E_8gt.book Page 1 Tuesday, March 28, 2006 5:37 PM
ESU05070
1-
YAMAHA MOTOR CORPORATION, U.S.A.
SNOWMOBILE LIMITED WARRANTY
CW-07E
Yamaha Motor Corporation, U.S.A. hereby warrants that new Yamaha snowmobiles purchased from an autho­rized Yamaha snowmobile dealer in the continental United States will be free from defects in material and workman­ship for the period of time stated herein, subject to certain stated limitations.
WARRANTY PERIOD:
1. All Yamaha snowmobiles shall be warranted for a term of one (1) year from the date of purchase, plus a special early-season extension (if applicable).
2. All Yamaha snowmobile clutch components are war­ranted against abnormal wear for one (1) year from the date of purchase, plus a special early-season extension (if applicable).
DURING THE PERIOD OF WARRANTY any au-
thorized Yamaha snowmobile dealer will, free of charge, repair or replace, at Yamahas option, any part adjudged defective by Yamaha due to faulty workmanship or material from the factory. Parts used in warranty repairs will be warranted for the balance of the snowmobile’s warranty period. All parts replaced under warranty be­come the property of Yamaha Motor Corporation, U.S.A.
GENERAL EXCLUSIONS from this warranty shall
include any failures to the machine caused by:
1. Competition, racing, or non-Yamaha authorized rental use.
2. Operation on surfaces other than snow or ice.
3. Installation of parts or accessories that are not qual­itatively equivalent to genuine Yamaha parts.
4. Abnormal strain, neglect, or abuse.
5. Lack of proper maintenance.
6. Accident or collision damage.
7. Modification to original parts.
2. Give notice to an authorized Yamaha snowmobile dealer of any and all apparent defects within ten (10) days after discovery, and make the machine avail­able at that time for inspection and repairs at such dealers place of business. You may locate your nearest authorized Yamaha dealer through your local telephone directory.
WARRANTY TRANSFER: To transfer any remain-
ing warranty from the original purchaser to any subse­quent purchaser, it is imperative that the machine be inspected and registered for warranty by an authorized Yamaha snowmobile dealer. In order for this warranty to remain in effect, this inspection and registration must take place within ten (10) days after ownership transfer. An inspection and registration fee will be charged for this service.
EMISSION CONTROL SYSTEM WARRANTY
Yamaha Motor Corporation, USA also warrants to the ultimate purchaser and each subsequent purchaser of each 2006 and later model Yamaha snowmobile cov­ered by this warranty that the vehicle is designed, built, and equipped so as to conform at the time of sale with all U.S. emissions standards applicable at the time of manufacture and that it is free from defects in materials and workmanship which would cause it not to meet these standards within the period listed immediately below. Failures other than those resulting from defects in material or workmanship which arise solely as a result of owner abuse and/or lack of proper mainte­nance are not covered by this warranty.
All Models
Thirty (30) months from the original purchase date
SPECIFIC EXCLUSIONS
include parts replaced due to normal wear or routine maintenance including oil, spark plugs, clutch drive belts, slide runners, and track.
THE CUSTOMERS RESPONSIBILITY
warranty shall be to:
1. Operate and maintain the snowmobile as specified in the appropriate Owners Manual.
from this warranty shall
under this
1-1
E_8gt.book Page 2 Tuesday, March 28, 2006 5:37 PM
CW-08E
YAMAHA MOTOR CORPORATION, U.S.A. MAKES NO OTHER WARRANTY OF ANY KIND, EXPRESSED OR IMPLIED. ALL IMPLIED WAR­RANTIES OF MERCHANTABILITY AND FIT­NESS FOR A PARTICULAR PURPOSE WHICH EXCEED THE OBLIGATIONS AND TIME LIM­ITS STATED IN THIS WARRANTY ARE HEREBY DISCLAIMED BY YAMAHA MOTOR CORPO­RATION, U.S.A. AND EXCLUDED FROM THIS WARRANTY.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU. ALSO EXCLUDED FROM THIS WARRANTY ARE ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES INCLUDING LOSS OF USE. SOME STATES DO NOT AL­LOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAM­AGES, SO THE ABOVE EXCLUSION MAY NOT APPLY TO YOU.
THIS WARRANTY GIVES YOU SPECIFIC LE­GAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
WARRANTY QUESTIONS AND ANSWERS
Q. What costs are my responsibility during the warranty
period?
A. The customers responsibility includes all costs of
normal maintenance services, non-warranty repairs, accident and collision damages, as well as oil, spark plugs, clutch drive belts, and slide runners.
Q. What are some examples of “abnormal” strain, ne-
glect, or abuse?
A. These terms are general and overlap each other in
areas. Specific examples include: Running the ma­chine out of oil, hitting an object submerged under snow, operation on surfaces other than snow or ice, operating the machine with a broken or damaged part which causes another part to fail, and so on. If you have any specific questions on operation or maintenance, please contact your dealer for advice.
Q. May I perform any or all of the recommended main-
tenance shown in the Owners Manual instead of having the dealer do them?
A. Yes, if you are a qualified snowmobile mechanic and
follow the procedures specified in the Owners and Service Manual. We do recommend, however, that items requiring special tools or equipment be done by a Yamaha snowmobile dealer.
SPECIAL EARLY-SEASON WARRANTY EX­TENSION
A special warranty extension is available for all new Yamaha snowmobiles purchased between June 1 and December 1.
All new Yamaha snowmobiles purchased between June 1 and December 1 will have the warranty extended to November 30 of the following year.
YAMAHA MOTOR CORPORATION, U.S.A.
Post Office Box 6555
Cypress, California 90630
Q. Under what conditions is the clutch not covered by
warranty?
A. Clutches as well as clutch components wear with
use. Normal wear is not covered under warranty such service is the customers responsibility. Abnormal wear is, however, covered for one (1) year from the date of purchase. Your Yamaha snowmobile dealer possesses criteria as to what constitutes abnormal wear.
Q. Will the warranty be void or canceled if I do not
operate or maintain my new Yamaha exactly as specified in the Owners Manual?
A. No. The warranty on a new Yamaha cannot be
voided or canceled. However, if a particular failure is caused by operation or maintenance other than as shown in the Owners Manual, that failure may not be covered under warranty.
1-2
E_8gt.book Page 3 Tuesday, March 28, 2006 5:37 PM
CW-09E
Q. What responsibility does my dealer have under this
warranty?
A. Each Yamaha snowmobile dealer is expected to:
1. Completely set up every new machine before sale.
2. Explain the operation, maintenance, and warranty requirements to your satisfaction at the time of sale, and upon your request at any later date.
3. In addition, each Yamaha snowmobile dealer is held responsible for his setup, service and warranty repair work.
Q. Whom should I contact if I have further questions
about this warranty?
A. Your Yamaha snowmobile dealer has the informa-
tion and experience necessary to answer almost any questions about this warranty. If the dealer is not able to do so, he is expected to contact Yamaha Motor Corporation, U.S.A., for clarification or assistance.
CUSTOMER SERVICE
When contacting Yamaha Motor Corpora­tion, U.S.A. be sure to include the model, serial number, names, dates, and receipts.
CHANGE OF ADDRESS
The federal government requires each manufacturer of a motor vehicle to maintain a complete, up-to-date list of all first purchasers against the possibility of a safety-related defect and recall. This list is compiled from the purchase registrations sent to Yamaha Motor Corporation, U.S.A. by the selling dealer at the time of your purchase.
If you should move after you have purchased your new snowmobile, please advise us of your new address by sending a postcard listing your snowmobile model name, engine serial number, dealer number (or dealers name) as it is shown on your warranty registration identification, your name and new mailing address. Mail to:
If your machine requires warranty service, you must take it to any authorized Yamaha snowmobile dealer within the continental United States. Be sure to bring your warranty identification card or other valid proof of the original date of purchase. If a question or problem arises regarding warranty, first contact the owner of the dealer­ship. Since all warranty matters are handled at the dealer level, this person is in the best position to help you. If you are still not satisfied and require additional assistance, please write:
YAMAHA MOTOR CORPORATION, U.S.A.
CUSTOMER RELATIONS
DEPARTMENT
P.O. Box 6555
Cypress, California 90630
YAMAHA MOTOR CORPORATION, U.S.A.
WARRANTY DEPARTMENT
P.O. Box 6555
Cypress, California 90630
This will ensure that Yamaha Motor Corporation, U.S.A. has an up-to-date registration record in accordance with federal law.
1-3
E_8gt.book Page 4 Tuesday, March 28, 2006 5:37 PM
ESU04280

YAMAHA EXTENDED SERVICE (Y.E.S.)

CW-06E
1-4
E_8gt.book Page 1 Tuesday, March 28, 2006 5:37 PM
ESU04050
2-
LOCATION OF THE IMPORTANT
Please read the following labels carefully before operat­ing this snowmobile.
NOTE:
@
Maintain or replace safety and instruction labels, as nec­essary.
@
1
LABELS
2
3
8EK-77761-E0
4AA-22259-60
2-1
E_8gt.book Page 2 Tuesday, March 28, 2006 5:37 PM
NOTE:
@
The following suspension adjustment charts are included with the Owners Manual.
@
2-2
E_8gt.book Page 1 Tuesday, March 28, 2006 5:37 PM
ESU00008
When you ride your snowmobile, you must know and use the following for your safety. Severe injury or death may result if you ignore any of the following.
Before operating
1. Read the Owner’s Manual and all labels before oper-
2. This snowmobile was not manufactured for use on
3. This snowmobile is designed to carry the OPERA-
3-

SAFETY INFORMATION

ating this snowmobile. Become familiar with all of the operating controls and their function. Consult a Yamaha dealer about any control or function you do not understand.
public streets, roads, or highways. Such use is pro­hibited by law, and you could collide with another vehicle.
TOR ONLY. Passengers are prohibited. Carrying a passenger can cause loss of control.
4. Do not operate the snowmobile after drinking alcohol or taking drugs. Your ability to operate the snowmo­bile is reduced by the influence of alcohol or drugs.
5. For safety and proper care of the snowmobile, always perform the pre-operation checks on pages 6-1–6-11 before starting the engine. Check the throttle, brake, and steering for proper operation every time before starting the engine. Make sure that the throttle lever moves freely and it returns to the home position when it is released.
6. Apply the parking brake before starting the engine. Never drive the snowmobile with the parking brake applied. This may overheat the brake disc and reduce braking ability.
3-1
E_8gt.book Page 2 Tuesday, March 28, 2006 5:37 PM
7. Do not allow anyone to stand behind the snowmobile
8. Handle fuel with care; it is HIGHLY FLAMMABLE.
9. If you swallow some gasoline, inhale a lot of gasoline
when starting, inspecting, or adjusting the snowmo­bile. A broken track, track fittings, or debris thrown by the track could be dangerous to the operator or bystanders.
Never add fuel when the engine is running or hot.
Allow the engine to cool for several minutes after running. Use an approved fuel container.
Fill the fuel tank outdoors with extreme care.
Never remove the fuel cap indoors. Never fill the fuel tank indoors. Never refuel while smoking or in the vicinity of an
open flame. Make sure that the fuel tank cap is closed securely
after refueling. Wipe up any spilled fuel immedi­ately.
vapor, or get some gasoline into your eyes, see your doctor immediately. If any gasoline spills on your skin or clothing, immediately wash your skin with soap and water, and change your clothes.
10. Wear protective clothing. Wear an approved helmet, and a face shield or goggles. Also, wear a good qual­ity snowmobile suit, boots, and a pair of gloves or mit­tens that will permit use of your thumbs and fingers for operation of the controls.
Operation
1. Do not run the engine indoors, except when starting the engine to transport the snowmobile in or out of the building. Open the outside doors; exhaust fumes are dangerous.
2. Be careful where you ride. There may be obstacles hidden beneath the snow. Stay on established trails to minimize your exposure to hazards. Ride slowly and cautiously when you ride off of established trails. Hitting a rock or stump, or running into wires could cause an accident and injury.
3-2
E_8gt.book Page 3 Tuesday, March 28, 2006 5:37 PM
3. This snowmobile is not designed for use on surfaces
4. Avoid operating on glare ice, or on snow which has a
5. Always ride with other snowmobilers when going on a
6. Many surfaces such as ice and hard-packed snow
other than snow or ice. Use on dirt, sand, grass, rocks, or bare pavement may cause loss of control and may damage the snowmobile.
lot of dirt or sand mixed in. Operation under such conditions will damage or result in rapid wear of ski runners, drive track, slide runners, and drive sprock­ets.
ride. You may need help if you run out of fuel, have an accident, or damage your snowmobile.
require much longer stopping distances. Be alert, plan ahead and begin decelerating early. The best braking method on most surfaces is to release the throttle and apply the brake gentlynot suddenly.
Maintenance and storage
1. Do not leave the snowmobile on its left side for an extended period of time. Fuel may leak out from the fuel breather hose.
2. Modifications made to the snowmobile not approved by Yamaha, or the removal of original equipment may render your snowmobile unsafe for use that may cause severe personal injury. Modifications may also make the snowmobile illegal to use.
3. Never store the snowmobile with fuel in the fuel tank inside a building where ignition sources are present such as hot water and space heaters, an open flame, sparks, clothes dryers, and the like. Allow the engine to cool off before storing the snowmobile in an enclosed space.
4. Always refer to the “STORAGE section if the snow- mobile is to be stored for an extended period.
5. Maintain or replace safety and instruction labels, as necessary.
3-3
E_8gt.book Page 1 Tuesday, March 28, 2006 5:37 PM
ESU00012
4-

DESCRIPTION

Windshield
1
Steering handlebar
2
Seat
3
Frame
4
Storage compartment
5
Slide rail suspension
6
Drive track
7
Skis
8
Headlights
9
Shroud
0
4-1
E_8gt.book Page 2 Tuesday, March 28, 2006 5:37 PM
Tail/brake lights
A
Snow flap
B
Brake lever
C
Parking brake lever
D
Grip warmer adjustment switch
E
Headlight beam switch
F
Engine stop switch
G
Thumb warmer adjustment switch
H
Throttle lever
I
Main switch
J
Auxiliary DC jack
K
Tachometer
L
Mode button (not applicable)
M
Reset button
N
Select button
O
Fuel meter and grip/thumb warmer level
P
indicator Fuel meter indicator
Q
Self-diagnosis warning indicator
R
Rear suspension indicator
S
(not applicable) Coolant temperature warning indicator
T
Grip warmer indicator
U
Fuel level warning indicator
V
Thumb warmer indicator
W
Oil level warning indicator
X
Clock
Y
Low coolant temperature indicator light
Z
High beam indicator light
[
Warning light
\
Speedometer
]
Odometer/tripmeter/barometer
_
4-2
E_8gt.book Page 1 Tuesday, March 28, 2006 5:37 PM
ESU00013
ESU00362
Main switch
The main switch controls the following items.
1
The ignition circuit is switched off. The key can be removed only in this position.
2
The ignition circuit is switched on.
3
The starting circuit is switched on. The starter motor starts.
5-

CONTROL FUNCTIONS

OFF
ON
START”
CAUTION
@
:
Release the switch immediately after the engine starts.
@
NOTE:
@
The headlights, meter lights, and taillights come on after the engine starts.
@
ESU00022
Throttle lever
Once the engine is running cleanly, squeezing a the throt­tle lever 1 will increase the engine speed and cause engagement of the drive system. Regulate the speed of the snowmobile by varying the throttle position. Because the throttle is spring-loaded, the snowmobile will deceler­ate, and the engine will return to idle when it is released b.
WARNING
@
Check the throttle, brake, and steering for proper operation before starting the engine.
@
5-1
E_8gt.book Page 2 Tuesday, March 28, 2006 5:37 PM
ESU00361
Engine overheating prevention system
This model is equipped with an engine overheating pre­vention system to prevent overheating when the engine is idling. When the engine has been idling for at least 3 minutes and the coolant temperature has risen above 100 °C (212 °F), the engine automatically shuts off to prevent overheating.
NOTE:
The engine can be started after it shuts off.
ESU04701
Throttle override system (T.O.R.S.)
If the throttle bodies or throttle cable malfunctions during operation, the T.O.R.S. will operate when the throttle lever is released. The T.O.R.S. is designed to interrupt the fuel injection and keep the engine speed between 2,800 and 3,000 r/min if the throttle valves fail to return to the idle position when the throttle lever is released.
WARNING
@
If the T.O.R.S. is activated, make sure that the cause of the malfunction has been corrected and that the engine can be operated without a prob­lem before restarting the engine.
Be sure to use the specified spark plug and spark plug cap. Otherwise, the T.O.R.S. will not work properly.
@
5-2
E_8gt.book Page 3 Tuesday, March 28, 2006 5:37 PM
A
CA-19E
Item
Mode
A
Idling/
starting
B C
Running Trouble
Throttle switch Off On Off Throttle position
sensor
Engine Run Run
B
Idling/starting
È
Running
É
Tr o u b l e
Ê
Throttle position sensor (throttle valve position)
1
Throttle switch
2
Throttle cable
3
On
C
a
Off
b
Open
c
Closed
d
NOTE:
@
When the T.O.R.S. is activated, the warning light
Closed Open Open
T.O.R.S. will operate
4
and self-diagnosis warning indicator 5 will flash and the two-digit code “84” 6 will flash in the clock dis­play. The T.O.R.S. monitors the condition of the throttle
position sensor, speedometer assembly, and speed sensor, and will operate if any of the monitored items is disconnected or malfunctioning.
@
5-3
E_8gt.book Page 4 Tuesday, March 28, 2006 5:37 PM
ESU04711
Speedometer unit
The speedometer unit is equipped with the following:
After the engine is started, the tachometer 1 makes one sweep, and the low coolant temperature indicator light2, the warning light 3, and all segments of the meter display 4 turn on and off once. The grip warmer level is initially displayed for 5 seconds, then the display switches to the fuel meter.
a digital speedometer (which shows the riding speed) an odometer (which shows the total distance trav­eled) two tripmeters (which show the distance traveled since they were last set to zero) a barometer (which shows the ambient barometric pressure) a clock warning indicators (which show self-diagnosis, cool­ant temperature, fuel level, and oil level warnings) a fuel meter (which shows the fuel remaining in the fuel tank) a grip/thumb warmer level indicator (which shows the grip warmer level or the thumb warmer level) a display brightness control function
Odometer, tripmeter, and barometer modes
Pushing the “SELECT” button 1 switches the display between the odometer mode “ODO”, tripmeter modes TRIP A and TRIP B, and barometer mode BARO. To reset a tripmeter, push the “RESET” button for at least 1 second while the tripmeter is displayed.
NOTE:
@
To switch the speedometer, odometer, and tripmeter
displays between kilometers and miles, select the odometer mode “ODO”, and then push the “SELECT” button for at least 10 seconds while the snowmobile is stopped. To switch the barometer display between hectopascal
hPa and inches of mercury inHg, select the barometer mode “BARO”, and then push the SELECT button for at least 3 seconds while the snowmobile is stopped.
@
5-4
E_8gt.book Page 5 Tuesday, March 28, 2006 5:37 PM
Clock To set the clock
1. Push the “SELECT” button 1 and “RESET” button
2. Push the “RESET” button to change the hour setting,
3. Push the “RESET” button to change the minute set-
NOTE:
@
The clock must be set again when the battery is discon­nected.
@
Display brightness control
This function allows you to adjust the brightness of the meter display to suit the outdoor lighting conditions.
To adjust the display brightness
1. Turn the main switch to “OFF”.
2. Push and hold down the “SELECT” button 1.
3. Turn the main switch to “ON”, and then, after 5 sec-
4. Push the “RESET” button 2 to select the desired dis-
NOTE:
@
If the main switch is turned to “OFF” or the engine is started before completing the procedure, the setting is not applied.
@
2
simultaneously until the hour digits start flashing.
and then push the “SELECT” button. The minute dig­its will start flashing.
ting, and then push the “SELECT” button. The clock starts when the “SELECT” button is released.
onds, release the “SELECT” button.
play brightness level 3, and then push the “SELECT” button. The normal display returns when the SELECT button is released.
ESU00363
High beam indicator light
The high beam indicator light 1 comes on when the high beams of the headlights are switched on. (See page 5-10 for headlight beam switch operation.)
5-5
E_8gt.book Page 6 Tuesday, March 28, 2006 5:37 PM
ESU03824
Fuel meter and grip/thumb warmer level indicator
The fuel meter and grip/thumb warmer level indicator have eight segments 1 which show the amount of fuel remaining in the fuel tank, the grip warmer level, or the thumb warmer level.
Fuel meter
As the fuel level decreases in the fuel tank, the segments disappear until the level goes down to the last segment E (Empty). When this occurs, the fuel level warning indicator 2 and the warning light 3 come on. If the fuel level warning indicator and the warning light come on, fill the fuel tank at the first opportunity.
NOTE:
@
The snowmobile must be stopped on a level surface to obtain an accurate fuel meter reading, since the reading changes according to the movement and inclination of the snowmobile.
@
Grip/thumb warmer level indicator
The grip warmer adjustment switch 1 and the thumb warmer adjustment switch 2 control the electrically heated handlebar grips and throttle lever respectively. To raise the temperature, press the respective switch to HI. To lower the temperature, press the switch to “LO.
NOTE:
@
The grip warmer indicator 3 comes on and the dis-
play switches to the grip warmer level when the grip warmer adjustment switch is pressed. The thumb warmer indicator 4 comes on and the
display switches to the thumb warmer level when the thumb warmer adjustment switch is pressed. The grip/thumb warmer level is displayed for 5 seconds
after releasing the grip/thumb warmer adjustment switch, then the display switches to the fuel meter. The top segment of the grip/thumb warmer level indi-
cator flashes once when the grip/thumb warmer adjustment reaches the maximum level. The bottom segment of the grip/thumb warmer level indicator flashes once when the grip/thumb warmer adjust­ment reaches the minimum level. When the engine is started, the grip/thumb warmer
levels are set to the levels saved when the engine was stopped.
@
5-6
E_8gt.book Page 7 Tuesday, March 28, 2006 5:37 PM
ESU04260
Fuel level warning indicator
The fuel level warning indicator indicates a malfunction­ing sensor, disconnected coupler, broken lead, or short circuit when detected by the self-diagnosis device of the snowmobile. The fuel level warning indicator 1, warning light 2, and all segments of the fuel meter 3 warn the rider of the above problems by flashing continuously. When this occurs, have a Yamaha dealer inspect the snowmobile as soon as possible.
ESU03770
Oil level warning indicator
The oil level warning indicator 1 and the warning light come on when the engine oil level is low. If the oil level warning indicator and the warning light come on, place the snowmobile on a level surface and allow it to idle for one minute. If the oil level warning indicator and the warning light go off, the engine oil level is sufficient, however it is getting low. Add engine oil as soon as possible. If the oil level warning indicator and the warning light do not go off, check the engine oil level in the oil tank (see page 6-3), and add engine oil if necessary.
2
ESU04840
Low coolant temperature indicator light
The low coolant temperature indicator light 1 comes on when the coolant temperature is low and informs the rider that the snowmobile must be warmed up. After the engine is started, warm it up until the indicator light goes off. The snowmobile can be operated normally after the indi­cator light goes off.
NOTE:
@
While the low coolant temperature indicator light is on, the engine control system prevents the engine speed from rising even if the throttle lever is pressed.
@
5-7
E_8gt.book Page 8 Tuesday, March 28, 2006 5:37 PM
ESU04180
Coolant temperature warning indicator
If the engine overheats, the coolant temperature warning indicator 1 and the warning light 2 come on. When this occurs, stop the engine immediately and allow the engine to cool down, and then check the coolant level in the coolant reservoir. (See page 6-4.)
CAUTION
@
:
Do not operate the engine if it overheats.
@
ESU04254
Self-diagnostic system
This model is equipped with a self-diagnostic system for various electrical circuits. If any of those circuits are defective, the warning light and the self-diagnosis warning indicator 2 will flash, and then an error code (e.g., 16 and 81) 3 will flash slowly in the tripmeter/odometer display.
WARNING
@
If the self-diagnosis warning indicator and warn­ing light flash continuously, and an error code is displayed during operation, there may be some problem with the electrical circuit, lead couplers, etc.
Stop the engine and allow it to cool off. Then, check that the wire harness couplers in the engine compartment are connected properly.
If the self-diagnosis warning indicator, warning light, and an error code flash after the engine has been restarted, note the error code, and then have a Yamaha dealer inspect the snowmobile as soon as possible.
@
1
5-8
E_8gt.book Page 9 Tuesday, March 28, 2006 5:37 PM
ESU00031
Engine stop switch
The engine stop switch 1 is used to stop the engine in an emergency. Simply push 2 the stop switch to stop the engine. To start the engine, pull 3 the stop switch and proceed with starting the engine. (See page 7-1 for more details.) During the first few rides, practice using the stop switch so that you can react quickly in an emergency.
ESU00033
Brake lever
The snowmobile is stopped by braking the entire drive system. Squeeze the brake lever towards the handlebar grip to stop the snowmobile.
1 2 3
Brake lever Brake lever end Handlebar end
NOTE:
@
When the brake lever is operated, the brake light will illu­minate.
@
CAUTION
@
:
Make sure that the brake lever end does not project out over the handlebar end. This will help prevent brake lever damage when the snowmobile is placed on its side for service.
@
The brake lever is equipped with a position adjuster. To adjust the brake lever position:
1. Loosen the locknut 1.
2. While lightly pushing the brake lever in direction a, finger tighten the adjusting bolt 2 to set the brake lever to the desired position.
3. Tighten the locknut securely after adjusting the brake lever.
5-9
E_8gt.book Page 10 Tuesday, March 28, 2006 5:37 PM
A
ESU00035
Parking brake lever
When parking the snowmobile or starting the engine, apply the parking brake by moving the brake lever 1 to the left. To release the parking brake, move the parking brake lever 1 to the right.
To apply the parking brake
B
È
To release the parking brake
É
WARNING
@
Always set the parking brake before attempting to start the engine.
Never run the snowmobile with the parking brake applied. This may overheat the brake disc and reduce braking ability.
@
ESU00039
Headlight beam switch
Push the headlight beam switch to change the headlight beam to high or low.
Headlight beam switch
1
Push
2
High beam
3
Low beam
4
ESU04301
Auxiliary DC jack
The auxiliary DC jack is located in the front panel and can be used for accessories.
NOTE:
@
The auxiliary DC jack cannot be used if the engine is not running.
@
1. Start the engine.
2. Open the auxiliary DC jack cap 1, and then insert the accessory power plug into the jack 2.
NOTE:
@
After using the auxiliary DC jack, be sure to remove the accessory power plug from the jack and close the auxil­iary DC jack cap.
@
5-10
E_8gt.book Page 11 Tuesday, March 28, 2006 5:37 PM
CAUTION
@
Do not use accessories requiring more than the
:
maximum rated capacity for the auxiliary DC jack. This may overload the circuit and cause the fuse to blow. (See pages 8-34–8-35 for the specified amperage.) Do not use an automotive cigarette lighter or
other accessory with a plug that gets hot because the jack can be damaged.
@
Maximum rated capacity:
DC 12 V, 2.5 A (30 W)
ESU04730
Shroud and covers
Securely fasten the shroud and covers before operating the snowmobile. (See pages 8-5–8-7 for removal and installation procedures.)
Shroud
1
Right side cover
2
Left side cover
3
To p co ve r
4
WARNING
@
Do not drive the snowmobile with the shroud or
covers unfastened or removed. Keep your body and clothing away from rotating
parts when servicing the snowmobile with the shroud or covers removed. Do not touch the hot muffler and engine during or
immediately after operation.
@
CAUTION
@
:
Make sure that all cables, leads, etc., are in place when installing the shroud and covers.
@
5-11
E_8gt.book Page 12 Tuesday, March 28, 2006 5:37 PM
ESU00521
Drive guard
The drive guard is designed to cover the V-belt clutch and V-belt in case parts break or come loose.
@
@
ESU00053
V-belt holders
Keep a spare V-belt for emergency use by placing it into the V-belt holders provided.
WARNING
Make sure that the drive guard is tightened securely before operating the snowmobile. Never run the engine with the V-belt or drive guard removed.
CAUTION
@
:
Make sure that the V-belt is installed securely in the holders.
@
ESU00680
Storage compartment
Open the storage compartment to store the service tools, spare parts, or other small items.
5-12
Loading...
+ 70 hidden pages