Page 1
RM Series Wireless Microphone System
Reference Manual
Microphone Access Point
RM-WAP-8
Wireless Microphone
RM-WOM RM-WDR RM-WGL RM-WGS
Microphone Charger
RM-WCH-8
CONTENTS
INTRODUCTION....................................................................................................................................................................1
Information............................................................................................................................................................................................... 1
SETUP ...................................................................................................................................................................................2
CONTROLS AND CONNECTORS......................................................................................................................................12
RM-WAP-8............................................................................................................................................................................................. 12
RM-WOM RM-WDR .............................................................................................................................................................................. 14
RM-WGL RM-WGS ............................................................................................................................................................................... 16
RM-WCH-8 ............................................................................................................................................................................................ 17
WEB GUI..............................................................................................................................................................................19
Structure of RM-WAP Device Manager................................................................................................................................................. 19
Functions of RM-WAP Device Manager................................................................................................................................................ 21
MAIN SPECIFICATIONS .....................................................................................................................................................39
RM-WAP-8............................................................................................................................................................................................. 39
RM-WOM RM-WDR RM-WGL RM-WGS.............................................................................................................................................. 40
RM-WCH-8 ............................................................................................................................................................................................ 42
INTRODUCTION
Thank you for purchasing products of the Yamaha RM series wireless microphone system. This document provides detailed information
on the product functions and specifications as well as the Web GUI. For correct and safe use of the products, be sure to first read this
manual carefully together with the Owner’s Manual (included with each product).
Information
• The illustrations and images shown in this manual are for instructional purposes only.
• The company names and product names in this manual are trademarks or registered trademarks of their respective companies.
• We are continuously improving the software for our products. The latest version can be downloaded from the Yamaha website.
• This document is based on the latest specifications at the time of publication. The latest version can be downloaded from the Yamaha
website.
• Reproduction of this manual in whole or in part without permission is prohibited.
• In this manual, the microphone access point is referred to as “access point”, the wireless microphone is referred to as “microphone”,
and the microphone charger is referred to as “charger”.
RM Series Wireless Microphone System Reference Manual
1
Page 2
SETUP
In order to use the products, setup is required. Set up the products using the Web GUI “RM-WAP Device Manager”.
Prepare the following.
• Computer
• LAN cable
• PoE powered network switch
• RM-WAP
• RM-WCH (required for using the AUTO SETUP function)
• Microphones (RM-WOM, RM-WDR, RM-WGL or RM-WGS)
Starting RM-WAP Device Manager
1. Download the application “RM Device Finder” from the Yamaha website (U.S.A. and Canada:
https://uc.yamaha.com/support/, Other countries: https://download.yamaha.com/), and then start it.
2. Using a LAN cable, connect the computer to the network switch where the access point is connected.
3. Select a network in the [Select Network Interface Card] window, and then click [OK].
4. Double-click this unit in the [Detected Devices] window. Alternatively, select this unit, and then click the
[Browse] button.
The password settings window of RM-WAP Device Manager appears.
RM Series Wireless Microphone System Reference Manual
2
Page 3
5. Specify a password in the password settings window, and then click the [SET PASSWORD] button.
6. Type the password into the login window, and then click the [LOGIN] button.
The [HOME] window appears.
RM Series Wireless Microphone System Reference Manual
3
Page 4
SITE SURVEY
Before installing the products, use the SITE SURVEY function in RM-WAP Device Manager to measure the signal in the area.
With the SITE SURVEY function, you can check the number of microphones that can be used in the measured area.
The SITE SURVEY function is available via [TOOLS][SITE SURVEY] (Page 33).
IMPORTANT: If radio frequency interference occurs, there may be no sound from the microphones or the microphone connection
may be unexpectedly cut. We recommend thoroughly examining the environment before installation.
AUTO SETUP
After products have been installed, their settings can be specified.
With the AUTO SETUP function, product settings can be specified using the wizard.
IMPORTANT: • For details on mounting the access point to the wall or ceiling, read the RM-WAP Owner’s Manual.
• RM-WCH is required in order to use the AUTO SETUP function. Even in an environment where the AUTO SETUP
function cannot be used, RM-WAP Device Manager can be used to manually specify settings. (Page 19)
1. Click the [AUTO SETUP] button.
The wizard starts up.
RM Series Wireless Microphone System Reference Manual
4
Page 5
2. Follow the wizard’s instructions to continue the setup.
[1 Site Survey]
Check the contents of the window, and then click the [CONTINUE] button.
The window shows the number of microphones that can be used in the installation environment. It also shows the signal strength in the
installation environment and the channel usage status.
RM Series Wireless Microphone System Reference Manual
5
Page 6
NOTE: • You can also click the title of the next window (in this case, [2 General Settings]) to display the next window.
• Once the window has been displayed, the circled number in the window title is replaced with . Clicking a window
title where the circled number has been replaced with displays that window again.
RM Series Wireless Microphone System Reference Manual
6
Page 7
[2 General Settings]
1 [AP Name]
Allows you to select whether to specify the name of the access point automatically or manually.
2 [Locale]
Allows you to specify the time zone.
3 [Time Settings]
• Allows you to specify the date and time.
• Allows you to select whether to use NTP.
Check the access point settings, and then click the [CONTINUE] button.
1 3
2
NOTE: The access point settings can be changed if necessary.
RM Series Wireless Microphone System Reference Manual
7
Page 8
[3 Chargers Pairing]
PAIR button
1 Insert the charger power plug into an electrical outlet.
The charger starts up.
2 Long-press the PAIR button (on the bottom panel of the charger) for at least two seconds.
The access point and charger are paired. When pairing is finished, the charger name appears in the window.
NOTE: Pairing means that the products register each other with the information required for a DECT connection. The access
point and charger are paired, and a DECT connection is established at the same time.
3 Click the [CONTINUE] button.
RM Series Wireless Microphone System Reference Manual
8
Page 9
[4 Firmware Update]
1 If appears to the left of the charger name, click the [UPDATE ALL] button.
The charger firmware is updated. When the update is finished, changes to .
NOTE: If appeared from the beginning, step 1 does not need to be performed.
2 Place the microphone(s) on the charger.
The microphone firmware is updated. During the update, the Mic indicators (on the top panel of the microphone) flashes white
quickly. When the update is finished, the indicators go off.
IMPORTANT: Do not remove the microphone(s) from the charger until setup is finished.
NOTE: The microphones are updated one at a time.
3 Click the [CONTINUE] button.
RM Series Wireless Microphone System Reference Manual
9
Page 10
[5 Microphones Pairing]
The name(s) of the microphone(s) appear faintly in the window.
1 Long-press the ACTIVATE button (on the top panel of the charger) for at least two seconds.
The access point and microphone(s) are paired. When pairing is finished, the name(s) of the microphone(s) change from appearing
faintly to appearing in black.
NOTE: All microphones placed on the charger can be paired with a single long press.
2 Click the [CONTINUE] button.
RM Series Wireless Microphone System Reference Manual
10
Page 11
[6 Audio Routing]
Check the Dante channel to which each microphone is assigned, and then click the [CONTINUE] button.
NOTE: You can change the channel assignment by dragging the microphone name to the row of the desired Dante channel.
[7 Summary]
Check the microphone settings, and then click the [FINISH] button.
This completes the setup. When a microphone is removed from the charger, a DECT connection between the access point and
microphone will be established.
RM Series Wireless Microphone System Reference Manual
11
Page 12
CONTROLS AND CONNECTORS
1 2 3
RM-WAP-8
[Front panel]
1 Power indicator
Condition Power indicator Unit status
LAN cable plugged into Dante/PoE port Lit green Operating
– Flashes red quickly System error occurring
2 Status indicator
Condition Status indicator Unit status
Making DECT connection Lit blue DECT connection has been established
Pairing using Web GUI Flashes blue quickly Waiting for pairing/Pairing
Pairing using Web GUI
Pairing using Web GUI
Identify icon in Web GUI clicked Flashes white Responding (to Identify function)
Updating firmware Flashes white quickly Firmware being updated
Updating firmware
Updating firmware
– Flashes red Transmission error occurring
– Flashes red quickly System error occurring
3 Reset button
Condition Status indicator Unit status
Reset button long-pressed for 4 seconds to
less than 8 seconds, then released
Reset button long-pressed for 8 seconds to
less than 12 seconds, then released
(After flashing blue quickly)
Flashes blue twice
(After flashing blue quickly)
Flashes red twice
(After flashing white quickly)
Flashes white twice
(After flashing white quickly)
Flashes red twice
Flashes blue twice per second
(during long-pressing/resetting)
Flashes blue three times per second
(during long-pressing/resetting)
Paired successfully
Pairing failed
Firmware updated successfully
Firmware update failed
Network-related settings
Waiting for resetting/Resetting
(Automatically restarts after reset)
All settings
Waiting for resetting/Resetting
(Automatically restarts after reset)
NOTE: Use a fine-tipped object to press the Reset button.
RM Series Wireless Microphone System Reference Manual
12
Page 13
[Bottom panel]
1
1 Network port indicators (Dante/PoE port)
Network port indicator Unit status
Left indicator lit green Link up
Left indicator flashes green Transferring data
Left indicator unlit Link down
Right indicator lit green Operating on word clock of peripheral device (leader)
Right indicator flashes green Acting as word-clock leader
Right indicator flashes orange Word clock unlocked
NOTICE: • When disconnecting the LAN cable from the Dante/PoE port, wait at least five seconds before reconnecting the
cable. Otherwise, damage or malfunctions may result.
• With a Dante network, do not use the EEE function* of the network switch. Although mutual power consumption
settings are automatically adjusted between switches that support the EEE function, some switches do not perform
that properly. As a result, the switch’s EEE function may be enabled inappropriately in the Dante network, possibly
degrading clock synchronization performance and interrupting audio. Therefore, please note the following.
- When using managed switches, turn off the EEE function on all ports used for Dante. Do not use a switch that does
not allow the EEE function to be turned off.
- When using unmanaged switches, do not use switches that support the EEE function. In such switches, the EEE
function cannot be turned off.
* EEE (Energy-Efficient Ethernet) function: Technology that reduces the power consumption of Ethernet devices
during periods of low network traffic; also known as Green Ethernet or IEEE802.3az.
RM Series Wireless Microphone System Reference Manual
13
Page 14
RM-WOM RM-WDR
1
2
3
1
3
2
RM-WOM RM-WDR
[Top panel/side panel]
1 Mic buttons/indicators
Condition Mic indicator Unit status
Mic button touched Lit green Microphone on
Mic button touched
Identify icon in Web GUI clicked Flashes white Responding (to Identify function)
Updating firmware Flashes white quickly Firmware being updated
Updating firmware
Updating firmware
– Flashes red Transmission error occurring
– Flashes red quickly System error occurring
– Flashes red slowly Out of range for DECT connection
Lit red
(Flashes every 2 seconds)
(After flashing white quickly)
Flashes white twice
(After flashing white quickly)
Flashes red twice
Microphone off
Firmware updated successfully
Firmware update failed
RM Series Wireless Microphone System Reference Manual
14
Page 15
2 Battery button
3 Battery indicator
Condition Battery indicator Unit status
Charging the unit Lit green
Charging the unit Lit orange
Charging the unit Lit red
Charging the unit Unlit Charging finished
Battery button pressed Lit green for two seconds Remaining operating time of 15 hours or more
Battery button pressed Lit orange for two seconds
Battery button pressed Lit red for two seconds Remaining operating time of less than 3 hours
(Continuing to use the unit without charging) Flashes red Remaining operating time of less than 1 hour
Battery button long-pressed for 2 to 3
seconds
IMPORTANT: The microphone is pre-installed with an RM-WBT battery. In order to maintain battery capacity, charge the
microphone (battery) once every six months.
NOTE: • Power consumption can be reduced by putting the microphone in standby mode.
• Putting the microphone in standby mode cuts the DECT connection with the access point. When the standby mode
is exited (by long-pressing the Battery button again for 2 to 3 seconds), the connection is re-established.
Flashes orange slowly Enters standby mode
Charging (available operating time of 15 hours or more)
Charging (available operating time of 3 hours to less
than 15 hours)
Charging (available operating time of less than 3 hours)
Remaining operating time of 3 hours to less than 15
hours
[Bottom panel]
1
1 PAIR button
Condition Mic indicator Unit status
PAIR button long-pressed for at least 2 seconds Flashes blue quickly Waiting for pairing/Pairing
PAIR button long-pressed for at least 2 seconds
PAIR button long-pressed for at least 2 seconds
(After flashing blue quickly)
Flashes blue twice
(After flashing blue quickly)
Flashes red twice
Paired successfully
Pairing failed
RM Series Wireless Microphone System Reference Manual
15
Page 16
RM-WGL RM-WGS
1 1
3
4 4
3
2
2
RM-WGL RM-WGS
[Top panel/side panel]
1 Mic buttons/indicators
Mic button touched continuously
In Toggle mode: Mic button released Lit red Microphone off
In Push to talk mode:
Mic button touched continuously
In Push to talk mode: Mic button released
NOTE: Push to talk is a communication method that allows you to talk only while a button is pressed. Multiple devices cannot
All other Mic button/indicator functions are the same as described for RM-WOM and RM-WDR.
be used to talk at the same time. For details on switching to Toggle mode or Push to talk mode, refer to page 26.
2 Ring indicator
Flashes together with the Mic indicators.
3 Battery button
4 Battery indicator
Functions in the same way as the Battery button/indicator of the RM-WOM and RM-WDR.
Condition Mic indicator Unit status
In Toggle mode:
(Flashes every 2 seconds)
Lit green Microphone on
Lit green Microphone on while the button is touched
Lit red
Microphone off
RM Series Wireless Microphone System Reference Manual
16
Page 17
[Bottom panel]
5
1
5 PAIR button
Functions in the same way as the PAIR button of the RM-WOM and
RM-WDR.
RM-WCH-8
[Top panel]
1 ACTIVATE button/indicator
Condition ACTIVATE indicator Unit status
Power plug inserted into electrical outlet Lit green Operating
ACTIVATE button long-pressed for at least
2 seconds
ACTIVATE button long-pressed for at least
2 seconds
ACTIVATE button long-pressed for at least
2 seconds
Identify icon in Web GUI clicked Flashes white Responding (to Identify function)
Updating firmware Flashes white quickly Firmware being updated
Updating firmware
Updating firmware
– Flashes red Transmission error occurring
– Flashes red quickly System error occurring
Flashes blue quickly
(After flashing blue quickly)
Flashes blue twice
(After flashing blue quickly)
Flashes red twice
(After flashing white quickly)
Flashes white twice
(After flashing white quickly)
Flashes red twice
Waiting for pairing/Pairing of access point and
Access point and microphone(s) paired
Pairing of access point and microphone(s) failed
Firmware updated successfully
Firmware update failed
microphone(s)
successfully
RM Series Wireless Microphone System Reference Manual
17
Page 18
[Bottom panel]
1
1 PAIR button
Condition ACTIVATE indicator Unit status
PAIR button long-pressed for at least 2 seconds Flashes blue quickly Waiting for pairing/Pairing
PAIR button long-pressed for at least 2 seconds
PAIR button long-pressed for at least 2 seconds
(After flashing blue quickly)
Flashes blue twice
(After flashing blue quickly)
Flashes red twice
Paired successfully
Pairing failed
RM Series Wireless Microphone System Reference Manual
18
Page 19
WEB GUI
[HOME]
[Microphone Charger Status]
[Clock Synchronization Status]
[LED Indication Status]
[System Status]
[Microphone Status]
[SETTINGS] [Password Settings]
[Security Settings]
[Deployment Server Settings]
[Syslog Settings]
[ADMIN]
[REGION]
[Time Settings]
[Locale]
[Daylight Saving Settings]
[NETWORK]
[AP Name Settings]
[IP Address Settings]
[AUDIO]
[Dante Channels Setup]
[DECT Audio]
[DECT]
[DECT]
[DECT Synchronization]
[TOOLS]
[UPDATE]
[SITE SURVEY]
[Firmware Update]
[Upload New Firmware]
[CONFIGURATION]
[Export Configuration]
[LOGS]
[Reset Defaults]
[Logs]
[Import Configuration]
[CHARGER] [Chargers]
[MICROPHONE] [Microphones]
Page 21
Page 21
Page 21
Page 21
Page 23
Page 22
Page 23
Page 23
Page 23
Page 29
Page 29
Page 24
Page 30
Page 25
Page 31
Page 31
Page 32
Page 30
Page 32
Page 35
Page 37
Page 35
Page 37
Page 38
Page 37
Page 32
Page 33
Use the Web GUI “RM-WAP Device Manager” to check/change the settings of the units.
Structure of RM-WAP Device Manager
Refer to the page listed to the right for details on each item available in the various windows.
RM Series Wireless Microphone System Reference Manual
19
Page 20
The following icons/buttons are used in RM-WAP Device Manager.
(Information icon)
: Move the pointer over this icon to see more information about the item.
(Reload button): Click to update the window contents.
(Identify button)
: Click to cause the indicator of the corresponding device to flash.
(Link button): Click to go to another window for the item.
IMPORTANT: Be sure to click the [SUBMIT] button after changing settings in RM-WAP Device Manager. The [SUBMIT] button
always appears in the upper-right corner of the window.
RM Series Wireless Microphone System Reference Manual
20
Page 21
Functions of RM-WAP Device Manager
1
2
3
4
[HOME]
1 [System Status]
Allows you to check basic information about the access point.
2 [LED Indication Status]
Allows you to check the status of the Indicator of the access point.
3 [Clock Synchronization Status]
• Allows you to check the status of the Dante word clock.
“Leader” or “Follower” appears. If there is an abnormality in the word clock, this appears in orange.
• Allows you to check the status of the DECT frame synchronization.
“Leader” or “Follower” appears. When multiple access points are set up in the same group, one will be the “Leader” and the others
will be “Follower”. The access point group settings can be specified via [SETTINGS][DECT][DECT Synchronization].
4 [Microphone Charger Status]
Allows you to check the name of the charger.
RM Series Wireless Microphone System Reference Manual
21
Page 22
5 [Microphone Status]
5
Allows you to check the statuses of the microphones.
- [IPEI]:
Identification number of the DECT module
- [Link Quality]:
Shows the strength of the radio wave as one of four levels indicated by the number of bars.
- [Audio]:
Click the icon to turn on/off the microphone.
- [Battery Status]:
Shows the battery charge as a percentage.
Indicates the remaining charge of the battery by a color.
Red: 3% to 10%, 1 to 3 hours
Yellow: 10% to 50%, 3 to 15 hours
Green: 50% or more, 15 hours or more
- [Disconnect Time]:
Shows the time at which the microphone and access point were disconnected.
- [Connect Time]:
Shows the time at which the microphone and access point were connected.
- [FW Update Status]:
Shows the firmware update status.
If the firmware must be updated, appears.
Update the firmware via [TOOLS][UPDATE][Firmware Update].
RM Series Wireless Microphone System Reference Manual
22
Page 23
[SETTINGS]
[ADMIN]
1
3
1 [Password Settings]
Allows you to check/change the password for logging in to RM-WAP Device Manager.
2
4
2 [Security Settings]
Allows you to select whether to enable remote control. For details on remote control, refer to the RM Series Remote Control Protocol
Specifications.
IMPORTANT:
Remote control must be enabled for the access point to link to the RM-CR signal processor.
3 [Deployment Server Settings]
By using a deployment server, the device configuration file can be automatically acquired and applied to the device.
- [Enable Deployment Server]:
Allows you to select whether to use a deployment server.
- [Enable Automatic Server Discovery]:
Allows you to select whether to use the automatic discovery feature of the deployment server.
- [Primary Server], [Secondery Server]:
Specify the IP address of the deployment server when [Enable Automatic Server Discovery] is off.
- [Provisioning Internval]:
Allows you specify the deployment server provisioning interval.
4 [Syslog Settings]
Allows you to select whether to use a syslog server.
RM Series Wireless Microphone System Reference Manual
23
Page 24
[CHARGER]
1
1 [Chargers]
• Allows you to pair the access point and charger. Click the [PAIR NEW] button to put the access point in pairing standby mode, and
then long-press the PAIR button (on the bottom panel of the charger) for at least two seconds. When pairing is finished, the
charger name appears in the window.
• Allows you to check/change the name of the charger.
• Allows you to cancel pairing by clicking (trash can).
RM Series Wireless Microphone System Reference Manual
24
Page 25
[MICROPHONE]
1
1 [Microphones]
• Allows you to pair the access point and microphones. Click the [PAIR NEW] button in the window to put the access point in pairing
standby mode, and then long-press the PAIR button (on the bottom panel of the microphone) for at least two seconds. When
pairing is finished, the microphone name appears in the window.
• Shows the microphone settings as icons.
- [Start Mode]:
- [Start Mute Mode]:
- [Mic Button Behavior]:
- [Alarm when out of area]:
- [Fader Level]:
• Allows you to expand the settings window by clicking a row containing the name of a microphone.
: Starts up in Start Up mode.
: Starts up in Standby mode.
: Starts up with the microphone turned off.
: Starts up with the microphone turned on.
: The Mic button operates in Toggle mode.
: The Mic button operates in Push to talk mode.
: The Mic button is deactivated.
: The alarm when out of range for DECT connection is on.
: The alarm when out of range for DECT connection is off.
Shows the microphone fader level. The setting range is between –128 dB and +12 dB.
RM Series Wireless Microphone System Reference Manual
25
Page 26
• Allows you to check/change microphone settings.
- [Michrophone Name]:
Allows you to check/change the name of the microphone.
- [Group]:
Allows you to group the microphones. Grouping microphones synchronizes them when turning one on/off.
- [Start Mode]:
Allows you to select whether the microphone enters Standby mode when it is started up.
- [Start Mute Mode]:
Allows you to select whether the mic is on or off when the microphone is started up.
- [Mic Button Behavior]:
Allows you to set the operation of the Mic button to one of the following.
-[TOGGLE]:
Turn on/off the microphone by touching the Mic button.
- [PUSH TO TALK]:
The microphone is on while the Mic button is touched. Multiple devices cannot be used to talk at the same time.
- [DISABLE]:
The Mic button is deactivated.
- [Alarm when out of area]:
Allows you to select whether the Mic indicator flashes to indicate that the microphone is out of range for a DECT connection.
- [Fader Level]:
Allows you specify the microphone fader level. The setting range is between –128 dB and +12 dB.
- [High Pass Filter]:
Allows you to select the High Pass filter setting. Select one of the following: NONE, 110 Hz, 140 Hz, 175 Hz, 225 Hz.
- [Low Pass Filter]:
Allows you to select the Low Pass filter setting. Select one of the following: NONE, 4 kHz, 8 kHz, 12 kHz.
RM Series Wireless Microphone System Reference Manual
26
Page 27
- [Low Latency]
When Low Latency is on, processing of the following Advanced Audio Settings can be bypassed to reduce audio delay.
Input Gain, Adaptive Echo Canceller, Noise Reduction, Dereverberation, AGC and PEQ
When used in combination with RM-CR, turn off Low Latency.
- [Input Gain]
Allows you to select the microphone input gain.
With RM-WOM, select one of the following: OFF (0 dB), LOW (3 dB), MEDIUM (6 dB), HIGH (9 dB).
With RM-WDR, select one of the following: OFF (0 dB), LOW (4 dB), MEDIUM (8 dB), HIGH (12 dB).
With RM-WGS, select one of the following: OFF (0 dB), LOW (6 dB), MEDIUM (12 dB), HIGH (18 dB).
With RM-WGL, select one of the following: OFF (0 dB), LOW (6 dB), MEDIUM (12 dB), HIGH (18 dB).
- [Adaptive Echo Canceller]
Allows you to suppress echo generation. Select one of the following: OFF, GENTLE, MEDIUM, STRONG.
- [Noise Reduction]
Allows you to suppress ambient noise from the mix. Select one of the following: OFF, GENTLE, MEDIUM, STRONG.
- [Dereverberation]
Allows you to suppress reverberation. Select one of the following: OFF, GENTLE, MEDIUM, STRONG.
- [AGC Type]
AGC (Auto Gain Control) automatically adjusts the volume of the microphone. For the AGC type, select one of the following: OFF,
SOFT, HARD.
- [AGC Speed]
For the AGC speed, select one of the following: OFF, SLOW, FAST.
RM Series Wireless Microphone System Reference Manual
27
Page 28
- [Enable PEQ]
Allows you to select whether to enable PEQ (Parametric EQ). This is effective when used in combination with a processor other
than RM-CR.
- [Band], [Type], [Q], [Freq.], [Gain], [Bypass]
Allows you to specify PEQ settings for each of the six bands.
For [Type] under “Band A” or “Band F”, select one of the following: PEQ, L.SHELF-6dB/Oct, L.SHELF-12dB/Oct, H.SHELF-6dB/
Oct, H.SHELF-12dB/Oct, HPF, LPF.
• Allows you to cancel pairing by clicking (trash can).
RM Series Wireless Microphone System Reference Manual
28
Page 29
[AUDIO]
1
2
1 [Dante Channels Setup]
• Allows you to check the Dante channel assigned to each microphone.
• Allows you to change the channel assignment by dragging the microphone name to the row of the desired Dante channel.
2 [DECT Audio]
Allows you to set the access point to High Density mode or High Quality mode. High Quality mode has better audio quality than High
Density mode, but the maximum number of microphones that can be used may be limited.
RM Series Wireless Microphone System Reference Manual
29
Page 30
[DECT]
1
2
1 [DECT]
• Allows you to select the signal strength.
2 [DECT Synchronization]
Allows you to select whether to synchronize the DECT frame across multiple access points. When multiple access points are used,
turn on [Enable DECT Synchronization], and then put all devices to be synchronized into the same group under [Synchronization
group].
RM Series Wireless Microphone System Reference Manual
30
Page 31
[NETWORK]
1 2
1 [IP Address Settings]
Allows you to select whether to use DHCP. When set to use DHCP, the IP address is specified in Auto IP mode if there is no DHCP
server.
If settings have been incorrectly specified, press the Reset button on the front of the RM-WAP to reset the network-related settings.
2 [AP Name Settings]
Allows you to select whether to specify the name of the access point automatically or manually. For [UNIT ID], enter single-byte
hexadecimal characters.
RM Series Wireless Microphone System Reference Manual
31
Page 32
[REGION]
1 2
3
1 [Time Settings]
• Allows you to specify the date and time.
• Allows you to select whether to use NTP.
2 [Locale]
Allows you to specify the time zone.
3 [Daylight Saving Settings]
Allows you to select whether to use daylight saving time with the access point.
RM Series Wireless Microphone System Reference Manual
32
Page 33
[TOOLS]
[SITE SURVEY]
• Allows the access point to measure the signal strength in the installation environment and the channel usage status by clicking the
[START SURVEY] button.
IMPORTANT: If radio frequency interference occurs, there may be no sound from the microphones or the microphone connection
may be unexpectedly cut. We recommend thoroughly examining the environment before installation.
• Allows you to check the measurement results and the number of microphones that can be used in the installation environment, by
clicking the [RSSI SCAN MODE] button. For highly accurate measurements, make sure that all nearby wireless microphones and
other DECT devices are operational. In addition, it is recommended to measure for several hours under typical usage conditions in
order to obtain accurate results. The values beside “High Density Audio Mode” and “High Quality Audio Mode” refer to the maximum
number of microphones that can be used in each mode.
RM Series Wireless Microphone System Reference Manual
33
Page 34
• Allows you to check for DECT masters in the installation environment as well as their signal strength by clicking the [SYSTEM LIST
MODE] button.
RM Series Wireless Microphone System Reference Manual
34
Page 35
[UPDATE]
Allows you to update the firmware of access points, wireless microphones and chargers from the [UPDATE] window.
IMPORTANT: • Be sure to click the [TURN ON FWU MODE] button before updating the firmware.
• Be sure to click the [TURN OFF FWU MODE] button after updating the firmware.
RM Series Wireless Microphone System Reference Manual
35
Page 36
1
2
1 [Firmware Update]
Allows you to update the firmware of the charger and microphones by clicking the [UPDATE ALL] button.
2 [Upload New Firmware]
• Allows you to update the firmware of the access point. Click , select the firmware, and then click the [UPLOAD & UPDATE AP]
button.
NOTE: Alternatively, you can drag the firmware directly to the underlined area. The firmware can also be updated from the
• Allows you to specify that the update will be performed automatically at the specified time.
deployment server.
RM Series Wireless Microphone System Reference Manual
36
Page 37
[CONFIGURATION]
1
3
2
1 [Export Configuration]
Allows you to export the settings by clicking the [EXPORT CONFIGURATION] button.
2 [Import Configuration]
Allows you to import settings. Click , select a settings file, and then click the [IMPORT CONFIGURATION] button.
NOTE: • Create the settings file to be imported by editing the one exported in 1.
• Alternatively, you can drag the settings file directly to the underlined area.
3 [Reset Defaults]
Allows you to reset the settings by clicking the [RESET DEFAULTS] button.
IMPORTANT: Be sure to check what is to be reset before doing it.
RM Series Wireless Microphone System Reference Manual
37
Page 38
[LOGS]
1
1 [Logs]
Allows you to download logs by clicking the [DOWNLOAD LOGS] button.
RM Series Wireless Microphone System Reference Manual
38
Page 39
MAIN SPECIFICATIONS
RM-WAP-8
General specifications
Dimensions W 171.2 mm × D 172.5 mm × H 42.8 mm
Weight 650 g (including mounting bracket)
Power requirements PoE (IEEE802.3af), 48 V DC
Maximum power consumption 48 V, 0.2 A
In operation
Storage
Indicators
Maximum number of connections to RM-CR 2
Accessories
Temperature 0 °C – 40 °C
Humidity 20% – 85% (no condensation)
Temperature −20 °C – 60 °C
Humidity 10% – 90% (no condensation)
• Power
• Status
• Network port
• Mounting bracket : 1
• Owner’s Manual (this document) : 1
Network specifications
• Dante audio/Dante control
Dante/PoE port
• External control
•PoE
• Cable requirements: CAT5e or higher, STP
Audio specifications
Sampling rate 48 kHz
Bit depth 24-bit
Audio input/output (Dante)
8 out
out1–out8: Mic input signals (maximum 8)
Wireless specifications
Supported standard 1.9 GHz DECT standard
• USA/Canada: 1920.0 MHz – 1930.0 MHz
Radio frequency
Maximum output power (EIRP)
Antenna (built-in) Supports space diversity
Use
Maximum coverage distance 50 m (depends on the usage environment)
Encryption method AES (256-bit)
• Europe/Northern Europe/UK/Australia/New Zealand:
1880.0 MHz – 1900.0 MHz
• Japan: 1893.5 MHz – 1906.1 MHz
• USA/Canada: 23.5 dBm
• Europe/Northern Europe/UK/Australia/New Zealand/Japan:
26.5 dBm
• Audio communication and control between access point and microphone
• Control between access point and charger
RM Series Wireless Microphone System Reference Manual
39
Page 40
RM-WOM RM-WDR RM-WGL RM-WGS
General specifications
RM-WOM
Dimensions
Weight
Power requirement
Maximum power consumption 5 V, 0.7 A
In operation
In charging
Storage
Indicators
Accessories
RM-WDR
RM-WGL W 89.0 mm × D 89.0 mm × H 308.4 mm
RM-WGS W 89.0 mm × D 89.0 mm × H 171.2 mm
RM-WOM 126 g
RM-WDR 130 g
RM-WGL 152 g
RM-WGS 140 g
Temperature 0°C – 40°C
Humidity 20% – 85% (no condensation)
Temperature 5 °C – 40 °C
Humidity 20% – 85% (no condensation)
Temperature −20 °C – 60 °C
Humidity 10% – 90% (no condensation)
RM-WOM
RM-WDR
RM-WGL
RM-WGS
RM-WOM
RM-WDR
RM-WGL
RM-WGS
W 89.0 mm × D 89.0 mm × H 26.0 mm
RM-WBT (lithium-ion battery)
Output: 3.60 V, 2350 mAh
•Mic
•Battery
•Mic
•Ring
•Battery
• RM-WBT (battery) :1
• Owner’s Manual (this document) :1
• Windscreen :1
• RM-WBT (battery) :1
• Owner’s Manual (this document) :1
RM Series Wireless Microphone System Reference Manual
40
Page 41
Audio specifications
Frequency response 160 Hz – 16 kHz (−10 dB)
Sampling rate 48 kHz
Bit depth 24-bit
30 – 35 ms nominal (no sound processing, High Quality mode) /
110 ms nominal (with sound processing, High Quality mode)
110 ms nominal (with sound processing, High Quality mode)
106.2 dB SPL
−19.3 dBA SPL
113.3 dBA
−12.2 dBFS/Pa
125.5 dBA
Latency
Maximum input level of
SPL (0 dBFS)
Self noise
SNR
(Ref. 94 dB SPL at 1 kHz)
Sensitivity
Dynamic range
RM-WGL
RM-WGS
RM-WDR
RM-WOM
RM-WOM 99.4 dB SPL
RM-WDR 100.2 dB SPL
RM-WGL
RM-WGS
RM-WOM −23.0 dBA SPL
RM-WDR −24.7 dBA SPL
RM-WGL
RM-WGS
RM-WOM 117.0 dBA
RM-WDR 118.7 dBA
RM-WGL
RM-WGS
RM-WOM −5.4 dBFS/Pa
RM-WDR −6.2 dBFS/Pa
RM-WGL
RM-WGS
RM-WOM 122.4 dBA
RM-WDR 124.9 dBA
RM-WGL
RM-WGS
Wireless specifications
Supported standard 1.9 GHz DECT standard
• USA/Canada: 1920.0 MHz – 1930.0 MHz
Radio frequency
Maximum output power (EIRP)
Antenna (built-in) Supports space diversity
Use Audio communication and control between access point and microphone
Maximum coverage distance 50 m (depends on the usage environment)
Encryption method AES (256-bit)
• Europe/Northern Europe/UK/Australia/New Zealand: 1880.0 MHz – 1900.0 MHz
• Japan: 1893.5 MHz – 1906.1 MHz
• USA/Canada: 23.5 dBm
• Europe/Northern Europe/UK/Australia/New Zealand/Japan: 26.5 dBm
RM Series Wireless Microphone System Reference Manual
41
Page 42
RM-WCH-8
General specifications
Dimensions W 304.0 mm × D 188.0 mm × H 41.5 mm
Weight 800 g
Power requirement
Maximum power consumption 16 V, 2.0 A
In operation
Storage
Indicator Activate
Accessories
Temperature 0°C – 40°C
Humidity 20% – 85% (no condensation)
Temperature −20 °C – 60 °C
Humidity 10% – 90% (no condensation)
P16V2.4A-R (AC adaptor)
Output: 16.0 V DC, 2.4 A
• P16V2.4A-R (AC adaptor) :1
•Power cord :1
• Owner’s Manual (this document) :1
Wireless specifications
Supported standard 1.9 GHz DECT standard
• USA/Canada: 1920.0 MHz – 1930.0 MHz
Radio frequency
Maximum output power (EIRP)
Antenna (built-in) Supports space diversity
Use Control between access point and charger
Maximum coverage distance 50 m (depends on the usage environment)
Encryption method AES (256-bit)
• Europe/Northern Europe/UK/Australia/New Zealand: 1880.0 MHz – 1900.0 MHz
• Japan: 1893.5 MHz – 1906.1 MHz
• USA/Canada: 23.5 dBm
• Europe/Northern Europe/UK/Australia/New Zealand/Japan: 26.5 dBm
or 3
RM Series Wireless Microphone System Reference Manual
42
Manual Development Group
© 2022 Yamaha Corporation
Published 02/2022
IP-A0
Loading...