Yamaha FZR User Manual
2010 WaveRunner
FZR
OWNER’S/OPERATOR’S MANUAL
Read this manual carefully
before operating this watercraft.
F2R-F8199-71-E0
Read this manual carefully before operating this watercraft. This manual
should stay with the WaveRunner if it is sold.
Important manual information
EJU37551
Declaration of Conformity for Personal Watercraft (PWC)
with the requirements of Directive 94/25/EC
as amended by Directive 2003/44/EC
Name of PWC manufacturer:
YAMAHA MOTOR CO., LTD.
Address: 2500 Shingai
Town: Post Code: 438-8501Iwata, Shizuoka
Country: Japan
Name of Authorized Representative (if applicable):
YAMAHA MOTOR EUROPE N.V.
Address: Koolhovenlaan 101
Town: Schiphol-Rijk Post Code: 1119 NC
Revision No:
Country: The Netherlands
Name of Notified Body for noise emission assessment: Luxcontrol SA
Address: 1, avenue des Terres Rouges BP 349
Town:Esch-sur-Alzette Post Code: L-4004
Country: Luxembourg ID Number:0882
Name of Notified Body for exhaust emission assessment: Luxcontrol SA
Address: 1, avenue des Terres Rouges BP 349
Town: Esch-sur-Alzette Post Code: L-4004
Country: Luxembourg ID Number: 0882
ECtype-examination Certificate number (if applicable): LC*2003/44*10026
Important manual information
Conformity assessment modules used:
for construction: A
for noise emissions: Aa G H
for exhaust emissions: B+E B+D B+C B+F G H
Other Community Directives applied:
Directive 89/336/EEC relating to electromagnetic compatibility (EMC),
using the following standards, for emission CISPR12:2001, for generic
immunity EN61000-6-2:2001
DESCRIPTION OF CRAFT
Craft model Identification Number, starting from
U S Y A M 0 1G9A10 0–1
Model name / Commercial name :
-
GX1800-J / FZR
IDENTIFICATION OF ENGINE(S) COVERED
BY THIS DECLARATION OF CONFORMITY
Combustion cycle:
Unique engine identification number(s)
or engine family code(s)
6AN LC*2003/44*10026
ESSENTIAL
REQUIREMENTS
I.A design and construction
I.B exhaust emissions
I.C noise emissions
Aa B+C B+D B+E B+F G H
Design Category:
C D
2 stroke 4 stroke
EC Type–examination certificate
(for exhaust)
standards
other
normative
document/
method
technical
file
Please specify in more detail
(* = mandatory standard)
EN ISO 13590
* *EN ISO 8178-1:1996
* *EN ISO 14509
This declaration of conformity is issued under the sole responsibility of the PWC
manufacturer. I declare on behalf of the PWC manufacturer that the craft model and
engine(s) mentioned above comply with all applicable essential requirements in the way
specified and are in conformity with the type for which above mentioned EC typeexamination certificate(s) has(have) been issued.
Name / title: S. Hayakawa / President of YAMAHA MOTOR EUROPE N.V.
(identification of the person empowered to sign on behalf
of the PWC manufacturer or his authorized representative)
Signature:
(or an equivalent marking)
Date and place of issue: 1st / August / 2009, Schiphol-Rijk, The Netherlands
Important manual information
EJU30192
To the owner/operator
Thank you for choosing a Yamaha watercraft.
This owner’s/operator’s manual contains information you will need for proper operation,
maintenance, and care. If you have any questions about the operation or maintenance of
your watercraft, please consult a Yamaha
dealer.
This manual is not a course on boating safety
or seamanship. If this is your first watercraft,
or if you are changing to a type of watercraft
you are not familiar with, for your own comfort
and safety, please ensure that you obtain
proper training or practice before operating
the watercraft by yourself. In addition, a
Yamaha dealer or boating organization will be
pleased to recommend local sea schools, or
competent instructors.
In this manual, information of particular importance is distinguished in the following ways:
This is the safety alert symbol. It is used
to alert you to potential personal injury hazards. Obey all safety messages that follow
this symbol to avoid possible injury or death.
EWJ00071
WARNING
A WARNING indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
ECJ00091
NOTICE
A NOTICE indicates special precautions
that must be taken to avoid damage to the
watercraft or other property.
EJU40410
Because Yamaha has a policy of continuing
product improvement, this product may not be
exactly as described in this owner’s/operator’s manual. Specifications are subject to
change without notice.
This manual should be considered a permanent part of this watercraft and should remain
with it even if the watercraft is subsequently
sold.
EJU30232
WaveRunner FZR
OWNER’S/OPERATOR’S MANUAL
©2009 by Yamaha Motor Co., Ltd.
1st Edition, July 2009
All rights reserved.
Any reprinting or unauthorized use
without the written permission of
Yamaha Motor Co., Ltd.
is expressly prohibited.
Printed in U.S.A.
TIP:
A TIP provides key information to make procedures easier or clearer.
Table of contents
General and important labels........... 1
Identification numbers .................... 1
Primary Identification (PRI-ID)
number ........................................... 1
Craft Identification Number (CIN) ...... 1
Engine serial number ........................ 1
Model information ........................... 2
Builder’s plate .................................... 2
Important labels .............................. 3
Warning labels ................................... 4
Other labels ....................................... 8
Safety information........................... 10
Limitations on who may operate
the watercraft ............................ 10
Cruising limitations ....................... 11
Operation requirements ............... 12
Recommended equipment ........... 14
Hazard information ....................... 15
Watercraft characteristics ............. 15
Safe boating rules ........................ 17
Enjoy your watercraft
responsibly ................................ 17
Description....................................... 19
Watercraft glossary ...................... 19
Location of main components ...... 20
Control function operation ............. 24
Watercraft control functions ......... 24
Remote control transmitter .............. 24
Yamaha Security System ................ 25
Engine stop switch .......................... 26
Engine shut-off switch ..................... 26
Start switch ...................................... 26
Throttle lever ................................... 27
Steering system ............................... 27
Telescopic steering system ............. 28
Cooling water pilot outlets ............... 28
Water separator ............................... 29
Watercraft operation ....................... 30
Watercraft operation functions ..... 30
Reverse system ............................... 30
Quick Shift Trim System
(Q.S.T.S.) ..................................... 31
Watercraft operation modes ......... 32
Low RPM Mode ............................... 32
Instrument operation ...................... 34
Dual analog meter unit ................. 34
Speedometer ................................... 34
Tachometer ..................................... 34
Information display .......................... 35
Equipment operation ...................... 39
Equipment .................................... 39
Seats ............................................... 39
Reboarding grip ............................... 40
Reboarding step .............................. 40
Bow eye ........................................... 41
Stern eyes ....................................... 41
Storage compartments .................... 41
Fire extinguisher holder and
cover ............................................ 44
Operation and handling
requirements ................................... 46
Fuel requirements ........................ 46
Fuel ................................................. 46
Engine oil requirements ............... 48
Engine oil ......................................... 48
Draining the bilge water ............... 49
Draining the bilge water on land ...... 49
Draining the bilge water on water .... 50
Transporting on a trailer ............... 51
First-time operation ........................ 52
Engine break-in ............................ 52
Pre-operation checks ..................... 53
Pre-operation checklist .................... 53
Pre-operation check points .......... 55
Pre-launch checks ........................... 55
Table of contents
Post-launch checks ......................... 62
Operation ......................................... 63
Operating your watercraft ............. 63
Getting to know your watercraft ....... 63
Learning to operate your
watercraft ..................................... 63
Riding position ................................. 64
Launching the watercraft ................. 64
Starting the engine on water ........... 64
Stopping the engine ........................ 65
Leaving the watercraft ..................... 65
Operating the watercraft .................. 65
Turning the watercraft ..................... 66
Stopping the watercraft ................... 67
Operating the watercraft in
reverse ......................................... 68
Boarding the watercraft ................... 68
Starting off ....................................... 71
Capsized watercraft ......................... 72
Beaching and docking the
watercraft ..................................... 73
Operating in weeded areas ............. 73
After removing the watercraft from
the water ...................................... 74
Specifications.................................. 85
Specifications................................ 85
Trouble recovery............................. 86
Troubleshooting ........................... 86
Troubleshooting chart ...................... 86
Emergency procedures ................ 89
Cleaning the jet intake and
impeller ........................................ 89
Jumping the battery ......................... 90
Replacing the fuses ......................... 90
Towing the watercraft ...................... 92
Submerged watercraft ..................... 92
Care and storage ............................. 75
Post-operation care ...................... 75
Flushing the cooling water
passages ...................................... 75
Cleaning the watercraft ................... 76
Battery care ..................................... 76
Long-term storage ........................ 79
Cleaning .......................................... 79
Lubrication ....................................... 79
Rustproofing .................................... 79
Maintenance..................................... 81
Maintenance ................................. 81
Tool kit ............................................. 81
Removing and installing the engine
cover ............................................ 81
Periodic maintenance chart ............. 83
Engine oil and oil filter ..................... 84
General and important labels
EJU36450
Identification numbers
Record the Primary Identification (PRI-ID)
number, Craft Identification Number (CIN),
and engine serial number in the spaces provided for assistance when ordering spare
parts from a Yamaha dealer. Also record and
keep these ID numbers in a separate place in
case your watercraft is stolen.
EJU41350
Primary Identification (PRI-ID) number
The PRI-ID number is stamped on a plate attached inside the engine compartment. (See
page 39 for seat removal and installation procedures and page 44 for information on the
watertight storage compartment.)
MODEL:
GX1800-J (FZR)
1
EJU36550
Craft Identification Number (CIN)
The CIN is stamped on a plate attached to the
aft deck.
1
1 Craft Identification Number (CIN) location
EJU40470
Engine serial number
The engine serial number is stamped on a
plate attached to the engine unit. (See page
39 for seat removal and installation procedures and page 81 for engine cover removal
and installation procedures.)
1 Primary Identification (PRI-ID) number loca-
tion
PRI-I.D.
MODEL
YAMAHA MOTOR CO., LTD.
ASSEMBLED IN U.S.A. FROM AMERICAN AND JAPANESE
COMPONENTS.
ASSEMBLÉ AUX ÉTATS-UNIS DE PIÈCES AMÉRICANES ET
JAPONAISES.
F2R
F2R
1
1
1 Engine serial number location
General and important labels
EJU30320
Model information
EJU30331
Builder’s plate
Watercraft with this label conform to certain
portions of the European Parliament directive
relating to machinery.
Part of the information is given on the builder’s
plate affixed on the craft. A full explanation of
this information is given in the relevant sections of this manual.
1
1 Builder’s plate location
TIP:
The significant wave height is the mean
height of the highest one-third of the waves,
which approximately corresponds to the wave
height estimated by an experienced observer.
However, some waves will be double this
height.
Design category of this personal watercraft: C
Category C:
This watercraft is designed to operate in
winds up to Beaufort force 6 and the associated wave heights (significant wave heights up
to 2 m (6.56 ft); see the following TIP). Such
conditions may be encountered in exposed
inland waters, in estuaries, and in coastal waters in moderate weather conditions.
2
General and important labels
EJU30452
Important labels
Read the following labels before using this watercraft. If have any questions, consult a Yamaha
dealer.
16
1
7
8
13
12
15
6
5
3
2
14
4
10
11
9
3
General and important labels
EJU35912
Warning labels
If any of these labels are damaged or missing, contact a Yamaha dealer for replacements.
1
4
General and important labels
5
General and important labels
5
6
78
WARNING
WARNING
AVERTISSEMENT
(F2R-U41E1-00)
AVERTISSEMENT
(F2R-U41E1-00)
6
General and important labels
7
EJU36261
Other labels
12
13
14
General and important labels
(F2R-U41E1-00)
The following label indicates the correct direction to upright a capsized watercraft.
8
General and important labels
The following CE marking is located on the back of the remote control transmitter.
9
Safety information
EJU30682
The safe use and operation of this watercraft is dependent upon the use of proper
riding techniques, as well as upon the
common sense, good judgment, and expertise of the operator. Before using this
watercraft, make sure that its use is permitted under local laws, bylaws, and regulations, and always operate the watercraft
in full conformity with any requirements
and limitations imposed. Every operator
should know the following requirements
before riding the watercraft.
● Before operating the watercraft, read this
owner’s/operator’s manual, the Riding
Practice Guide, the Riding Instruction card,
and all labels on the watercraft. These materials should give you an understanding of
the watercraft and its operation.
● Never allow anyone to operate this water-
craft until they too have read this owner’s/operator’s manual, the Riding Practice
Guide, the Riding Instruction card, and all
labels.
EJU30720
Limitations on who may
operate the watercraft
● Yamaha recommends a minimum operator
age of 16 years old.
Adults must supervise use by minors.
Know your local operator age and training
requirements.
● This watercraft is designed to carry the op-
erator and 1 passenger. Never exceed the
maximum load limit or allow more than 2
persons to ride the watercraft at any time.
Maximum load:
160 kg (353 lb)
Load is the total weight of cargo, operator, and passenger.
● Do not operate the watercraft with a pas-
senger on board until you have considerable practice and experience riding alone.
Operating the watercraft with a passenger
requires more skill. Take the time to become accustomed to the handling characteristics of the watercraft before trying any
difficult maneuvers.
10
Safety information
EJU30761
Cruising limitations
● Scan constantly for people, objects, and
other watercraft. Be alert for conditions that
limit your visibility or block your vision of
others.
● Operate defensively at safe speeds and
keep a safe distance away from people, objects, and other watercraft.
● Do not follow directly behind watercraft or
other boats.
● Do not go near others to spray or splash
them with water.
● Avoid sharp turns or other maneuvers that
make it hard for others to avoid you or understand where you are going.
● Avoid areas with submerged objects or
shallow water.
● Take early action to avoid collisions. Re-
member, watercraft and other boats do not
have brakes.
● Do not release the throttle lever when trying
to steer away from objects—you need throttle to steer. Always check throttle and steering controls before starting the watercraft.
● Ride within your limits and avoid aggressive
maneuvers to reduce the risk of loss of control, ejection, and collision.
● This is a high performance boat—not a toy.
Sharp turns or jumping wakes or waves can
increase the risk of back/spinal injury (paralysis), facial injuries, and broken legs, an-
kles, and other bones. Do not jump wakes
or waves.
● Do not operate the watercraft in rough wa-
ter, bad weather, or when visibility is poor;
this may lead to an accident causing injury
or death. Be alert to the possibility of adverse weather. Take note of weather forecasts and the prevailing weather conditions
before setting out on your watercraft.
● As with any water sport, you should not op-
erate your watercraft without someone else
nearby. If you operate further than swimming distance from shore, you should be
accompanied by another boat or watercraft,
but make sure you stay a safe distance
away. It’s good, common sense.
● Never operate in water that is less than 60
cm (2 ft) deep from the bottom of the watercraft, otherwise you increase your chance
of hitting a submerged object, which could
result in injury.
60 cm (2 ft)
● This watercraft is not equipped with lighting
required for night operation. Do not operate
the watercraft after sunset or before dawn,
otherwise you increase the risk of colliding
11
Safety information
with another boat, which could result in severe injury or death.
● Follow navigation rules, and state/provin-
cial and local laws that apply to watercraft.
EJU30801
Operation requirements
● All riders must wear a personal flotation de-
vice (PFD) that is approved by the appropriate authorities and is suitable for personal
watercraft use.
● Wear protective clothing. Severe internal
injuries can occur if water is forced into
body cavities as a result of falling into the
water or being near the jet thrust nozzle.
Normal swimwear does not adequately protect against forceful water entry into the rectum or vagina. All riders must wear a
wetsuit bottom or clothing that provides
equivalent protection. Such clothing includes thick, tightly woven, sturdy and
snug-fitting apparel such as denim, but
does not include spandex or similar fabrics,
like those used in bicycle shorts.
1 Authority-approved PFD
2 Wetsuit bottom
● Eye protection is recommended to keep
wind, water, and glare from the sun out of
your eyes while you operate your watercraft. Restraining straps for eyewear are
made which are designed to float should
your eyewear fall in the water.
Footwear and gloves are recommended.
● You must decide whether to wear a helmet
while you ride for recreation. You should
know that a helmet could help protect you in
12
Safety information
certain kinds of accidents and that it could
injure you in others.
A helmet is designed to provide some head
protection. Although helmets cannot protect
against all foreseeable impacts, a helmet
might reduce your injuries in a collision with
a boat or other obstacle.
A helmet may have potential safety hazards, as well. Falling into the water could
risk the chance of the helmet catching water, commonly known as “bucketing”, and
the resulting strain on your neck could
cause choking, severe and permanent neck
injuries, or death. A helmet could also increase the risk of an accident if it reduces
your vision or hearing, or if it distracts you or
increases your fatigue.
How should you decide if a helmet’s potential safety benefits outweigh its potential
risks for you? Consider your particular
riding conditions. Consider factors such as
your riding environment and your riding
style and ability. Also consider the likelihood of traffic congestion, and the water
surface conditions.
If you decide to wear a helmet based upon
your riding circumstances, choose one
carefully. Look for a helmet designed for
personal watercraft use, if possible. If you
will be engaging in closed-course competition, follow the helmet requirements of the
sanctioning organization.
● Never operate the watercraft after consum-
ing alcohol or taking other drugs.
● For reasons of safety and proper care of the
watercraft, always perform the pre-operation checks listed on page 53 before operating the watercraft.
● The operator and passenger should always
keep their feet on the floor of the footwell
when the watercraft is in motion. Lifting your
feet increases the chances of losing your
balance, or hitting objects outside the watercraft with your feet. Do not give a ride to
a child whose feet cannot reach the floor of
the footwell.
● The passenger should firmly hold on to the
operator.
● Never allow a passenger to ride in front of
the operator.
● Always consult your doctor on whether it is
safe for you to ride this watercraft if you are
pregnant or in poor health.
● Do not attempt to modify this watercraft.
Modifications to your watercraft may reduce
safety and reliability, and render the watercraft unsafe or illegal for use.
● Attach the engine shut-off cord (lanyard) to
your left wrist and keep it free from the handlebars so that the engine stops if you, the
operator, fall off. After riding, remove the
engine shut-off cord (lanyard) from the wa-
13
Safety information
tercraft to avoid accidental starting or unauthorized use by children or others.
● Scan carefully for swimmers and stay away
from swimming areas. Swimmers are hard
to see and you could accidentally hit someone in the water.
● Avoid being hit by another boat. You should
always take the responsibility to watch for
traffic; other boaters may not be watching
for you. If they do not see you, or if you maneuver more quickly than other boaters expect, you risk a collision.
● Maintain a safe distance from other boats
and watercraft, and also watch for ski ropes
or fishing lines. Obey the “Safe boating
rules” and be sure to check behind you before making a turn. (See “Safe boating
rules” on page 17.)
EJU30840
Recommended equipment
The following items should be carried on
board your watercraft:
● Sound-signaling device
You should carry a whistle or other soundsignaling device that can be used to signal
other boats.
● Visual distress signals
It is recommended that a pyrotechnic device, which is approved by the appropriate
authorities, be stored in a waterproof container on your watercraft. A mirror can also
be used as an emergency signal. Contact a
Yamaha dealer for more information.
● Watch
A watch is helpful so you will know how long
you have been operating the watercraft.
● Towline
A towline can be used to tow a disabled watercraft in an emergency.
14
Safety information
EJU36850
Hazard information
● Never start the engine or let it run for any
length of time in an enclosed area. Exhaust
fumes contain carbon monoxide, a colorless, odorless gas that may cause loss of
consciousness and death within a short
time. Always operate the watercraft in an
open area.
● Do not touch the hot muffler or engine dur-
ing or immediately after engine operation;
they can cause serious burns.
EJU30920
Watercraft characteristics
● Jet thrust turns the watercraft. Releasing
the throttle lever completely produces only
minimum thrust. If you are traveling at
speeds above trolling, you will have rapidly
decreasing ability to steer without throttle.
This model is equipped with the Yamaha
Engine Management System (YEMS) that
includes an off-throttle steering (OTS) system. It will activate at planing speeds should
you attempt to steer the watercraft after releasing the throttle lever. The OTS system
assists in turning by continuing to supply
some thrust while the watercraft is decelerating, but you can turn more sharply if you
apply throttle while turning the handlebars.
The OTS system does not function below
planing speeds or when the engine is off.
Once the engine slows down, the watercraft
will no longer turn in response to handlebar
input until you apply throttle again or you
reach trolling speed.
Practice turning in an open area without obstacles until you have a good feel for this
maneuver.
● This watercraft is water-jet propelled. The
jet pump is directly connected to the engine.
This means that jet thrust will produce some
movement whenever the engine is running.
There is no “neutral” position. You are in either “forward” or “reverse”, depending upon
the shift lever position.
● Do not use the reverse function to slow
down or stop the watercraft as it could
cause you to lose control, be ejected, or impact the handlebars.
This could increase the risk of back/spinal
injury (paralysis), facial injuries, and broken
legs, ankles, and other bones. You could
also damage the shift mechanism.
15
Safety information
● Reverse can be used to slow down or stop
during slow-speed maneuvering, such as
when docking. Once the engine is idling,
shift into reverse and gradually increase engine speed. Make sure that there are no obstacles or people behind you before shifting
into reverse.
● Keep away from the intake grate while the
engine is on. Items such as long hair, loose
clothing, or PFD straps can become entangled in moving parts, resulting in severe injury or drowning.
● Never insert any object into the jet thrust
nozzle while the engine is running. Severe
injury or death could result from coming in
contact with the rotating parts of the jet
pump.
2
any debris or weeds, which may have collected around the jet intake.
2
1
1 Clip
2 Engine shut-off switch
1
1 Intake grate
2 Jet thrust nozzle
● Stop the engine and remove the clip from
the engine shut-off switch before removing
16
Safety information
EJU30970
Safe boating rules
Your Yamaha watercraft is legally considered
a powerboat. Operation of the watercraft must
be in accordance with the rules and regulations governing the waterway on which it is
used.
EJU30991
Enjoy your watercraft
responsibly
You share the areas you enjoy when riding
your watercraft with others and with nature.
So your enjoyment includes a responsibility to
treat these other people, and the lands, waters, and wildlife with respect and courtesy.
Whenever and wherever you ride, think of
yourself as the guest of those around you. Remember, for example, that the sound of your
watercraft may be music to you, but it could be
just noise to others. And the exciting splash of
your wake can make waves others won’t enjoy.
Avoid riding close to shoreline homes and waterfowl nesting areas or other wildlife areas,
and keep a respectful distance from fishermen, other boats, swimmers, and populated
beaches. When travel in areas like these is
unavoidable, ride slowly and obey all laws.
Proper maintenance is necessary to ensure
that the exhaust emission and sound levels of
your watercraft will continue to be within regulated limits. You have the responsibility to
make sure that the recommended maintenance in this owner’s/operator’s manual is
carried out.
Remember, pollution can be harmful to the
environment. Do not refuel or add oil where a
spill could cause damage to nature. Remove
your watercraft from the water and move it
away from the shoreline before refueling. Dispose of water and any fuel and oil residue in
the engine compartment according to local
regulations. And keep your surroundings
pleasant for the people and wildlife that share
the waterways: don’t litter.
When you ride responsibly, with respect and
courtesy for others, you help ensure that our
17
waterways stay open for the enjoyment of a
variety of recreational opportunities.
Safety information
18
Description
EJU40302
Watercraft glossary
Trolling speed
“Trolling” is the lowest maneuvering speed. You are applying little or no throttle. The watercraft
is down in the water, and there is no wake.
Sub-planing speed
“Sub-planing” is a medium speed. The bow of the watercraft is slightly up from the water surface, but you are still traveling through the water. There is a wake.
Planing speed
“Planing” is a faster speed. The watercraft is more level and is skimming on top of the water.
There is a wake.
Bow
The front end of the watercraft.
Stern
The rear end of the watercraft.
Starboard
The right side of the watercraft when facing forward.
Port
The left side of the watercraft when facing forward.
Bilge water
Water that has collected in the engine compartment.
Yamaha Engine Management System (YEMS)
YEMS is an integrated, computerized management system that controls and adjusts ignition
timing, fuel injection, engine diagnostics, and the off-throttle steering (OTS) system.
19
EJU31011
Exterior
Description
Location of main components
3
1
4
2
5
6
7
1 Fuel filler cap (page 46)
2 Hood
3 Handlebars
4 Rear seat (page 39)
5 Front seat (page 39)
6 Footwell
7 Bow eye
8 Cooling water pilot outlet (page 28)
9 Gunwale
10 Sponson
10
9
8
20
Description
2
1
3
4
5
1 Boarding platform
2 Electric bilge pilot outlet
3 Reboarding grip (page 40)
4 Reboarding step (page 40)
5 Jet thrust nozzle
6 Reverse gate (page 30)
7 Ride plate
8 Stern drain plug (page 49)
9 Stern eye (page 41)
10 Speed sensor
11 Intake grate
9
6
7
8
10
11
21
Description
1234
5
67
1 Q.S.T.S. selector (page 31)
2 Q.S.T.S. selector lock lever (page 31)
3 Start switch (page 26)
4 Engine shut-off switch (page 26)
5 Clip (page 26)
6 Engine stop switch (page 26)
7 Engine shut-off cord (lanyard) (page 26)
8 Dual analog meter unit (page 34)
9 Rearview mirror
10 Glove compartment (page 42)
11 Remote control transmitter (page 24)
12 Beverage holder (page 44)
13 Shift lever (page 30)
14 Throttle lever (page 27)
10
98
14
11 12 13
22
Description
Engine compartment
2
1
7
3
5
6
4
8
1 Engine cover
2 Air filter case
3 Water separator (page 29)
4 Fuel tank
5 Battery (page 56)
6 Flushing hose connector
7 Electrical box
8 Spark plug/Spark plug cap/Ignition coil
9 Engine oil filler cap (page 48)
10 Dipstick
23
910
Loading...