Yamaha DTXPLORER Basic Set Assembly Manual

Basic Set Assembly Manual

This manual describes the standard assembly of the DTXPLORER Basic Set. After assembling the parts and connecting the cords as shown in Figure 1, the

unit is ready to be turned on.

* To assemble the unit, make sure you have the following three packages:

- RS40 (Rack System)

- DTLK9 (Pad Set)

- DTXPL (Trigger Module)

* Prepare beforehand a Phillips screwdriver, required in “ Mounting the

pads and the trigger module on the rack system”.

Before assembling the unit, lay a drum mat (sold separately).

Before assembling the unit, lay a drum mat on the  oor. Alternately, to prevent damaging your  oor, lay the cardboard box of the included packages, etc. on the  oor before assembling the two parts shown in the circles in Figure 1.

Figure 1: Unit Standard Assembly

DTXPL (Drum Trigger Module)

TP65 (Drum Pad)

AC Adaptor

HH65 (Hi-Hat Controller)

PCY65 (Single-zone Cymbal Pad)

RS40 (Rack System)

KP65 (Kick Pad)

FP6110A (Foot Pedal)

If this symbol is ignored and the equipment is used

CAUTION

Watch your fingers when adjusting clamps. They may become pinched, resulting in injury.

Make sure you hold onto the plug, not the cable, when connecting or disconnecting the cable. Also, never place any heavy or sharp objects on the cable. Applying excessive force to the cable may result in damage to the cable, such as the wires being severed, etc.

Do not step on or place heavy objects on the product. It may result in damage.

Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. may injure your fingers.

Do not put your hands or feet under the foot pedal or foot switch. They may be pinched, resulting in injury.

Do not use or keep the product in places with extremely high temperature (places in direct sunlight, close to a heater, in a closed car, etc.) or high humidity (bathroom, outside on a rainy day, etc.). Doing so may result in deformation, discoloration, damage or deterioration.

When cleaning the product, do not use benzine, thinner or alcohol as it may result in discoloration or deformation. Please wipe with a soft cloth or a damp cloth that has been wrung out thoroughly. If the product is soiled or sticky, use a neutral detergent on a cloth then wipe with a damp cloth that has been wrung out thoroughly to remove any remaining detergent. Also pay close attention so as not to let the water and detergent come into contact with the cushions used in the product; doing so may result in deterioration.

Do not attach acoustic drums to the electronic drum rack. Clamps may be damaged and drums may drop, causing injury.

improperly, there is a danger or injury to persons handling the equipment, and material damage could occur.

Checking the contents of RS40

Open the RS40 (Rack System) package and con rm the contents.

Figure 2: RS40 (Rack System)

RS40 (1) Fastening Screw (2) *1

Cable Band (10) *2

Assembly Manual (1) *3

- RS40

2 See Figure 3. Set up the rack system, with the YAMAHA logo label (a) on pipe facing the

opposite side from you. Support the rack system with your right hand, and loosen the two knobs (b) and (c) on your left.

Figure 4: Rack Assembly-2

3 See Figure 4. Move the leg on your left (pipe ) in a clockwise direction until it is about 90

degrees from pipe and  x the position of pipe

with the YAMAHA logo. Tighten the two knobs loosened in step 2

4 See Figure 3 again. Loosen the knob (d) on your right. 5 See Figure 4 again. Move the leg on your right (pipe ) in a counterclockwise direction

until it is parallel with pipe

* In the following steps, loosen the knobs  rst, decide the position of the pipe, and then

tighten the knobs. Be careful not to tighten the knobs excessively. For better performance, make minor adjustments for each part of the unit with the knobs after the assembly is completed.

. Tighten the knob loosened and  x the position of pipe .

6 Loosen the two knobs (e) aligned at the base of pipe , and move pipe slightly

outward in a counterclockwise direction. Tighten the two knobs loosened and  x the position of pipe

7 Loosen the two knobs ((f) on the middle left) aligned at the base of pipe . Move pipe

slightly outward in a clockwise direction. Tighten the two knobs loosened and  x the

position of pipe

8 Loosen the two knobs ((g) on the upper left) aligned at the base of pipe , and move pipe

outward in a clockwise direction until it is about 45 degrees from pipe . Tighten the

two knobs loosened and  x the position of pipe

9 Check that the entire rack system is stable. Hold the upper area of the vertical pipe and

, and shake them. If the rack system is unstable, retighten the knobs tightened in steps 2

to 5.

Figure 5: Rack Assembly-3

Checking the contents of the Pad Set and the

Trigger Module

Open the DTPK9 (Pad Set) and Trigger Module package and con rm the contents.

Figure 6: Pad Set DTLK9

TP65 (Drum Pad) (5) Clamp Bolt (5)

HH65 (Hi-Hat Controller) (1)

PCY65 (Cymbal Pad) (2)

KP65 (Kick Pad) (1)

FP6110A (Foot Pedal) (1)

Drum Key (1)

9-channel snake cable (1)

Instruction Manual (4)

- TP65/65S

- PCY65/65S

- HH65

- KP65

PRECAUTIONS

Before using, please read this assembly manual, and use this product in a safe and proper manner. Particularly in the case of children and young users, parents or an instructor should teach the children the proper manner in which to use the device.

If this symbol is ignored and the equipment is used

WARNING

Do not let small children assemble or set up this product by themselves, or they may be injured. Always assemble this product with adult supervision.

Be careful with the edges of the cymbal holders and the tom holders. The sharp holder ends may result in injury.

Be careful with the edges of the spurs attached to the base. The sharp spur ends may result in injury.

If this product is used with the rack system or a cymbal stand, make sure all bolts are tightened firmly. Also, when adjusting the height or angle, do not suddenly loosen the bolts. Loose bolts may result in the rack overturning or parts dropping, causing injury.

Always set the product on a flat and solid surface. Placement on a sloping, unstable surface or on steps may result in the product being unstable and subject to overturning.

When setting the product, please pay close attention to the handling and setting of cables. Carelessly placed cables may cause the user and others to trip and fall.

Do not alter the product. Doing so may result in injury or damage/deterioration to the product.

improperly, fatal injury to persons or serious damage could occur.

*1 Use fastening screws to attach the trigger module in “ Mounting the pads and the trigger module on the rack

system”. *2 Use cable bands to bind cables to pipes in “ *3 Not this manual.

Connecting to a power source”. (Spare bands are included.)

Assembling the Rack System

1 Take out the rack system from the package and remove all the cushioning. Remove the

bubble wrap on the pipes while assembling the rack system.

The pipe ends may injure your  ngers.

Figure 3: Rack Assembly-1

10 See Figure 5. Loosen the knobs of the cymbal holders and on the right and left

(shown with to the height illustrated. Tighten the knobs loosened and  x the positions of the cymbal holders.

on the opposite side of pipe ) and pull up the cymbal holders vertically

11 Loosen the two knobs (h) aligned along the pipe with the Trigger Module attachment part

. Adjust the Trigger Module attachment part diagonally to your side when set. Hold the Trigger Module attachment part turn it gradually. Tighten the two knobs loosened and  x the position of the Trigger Module attachment part

so the operating panel will face upward

 rmly and

Figure 7: Trigger Module

DTXPL (1) AC Adaptor (1)

Do not sit or step on the rack. The rack may overturn or be damaged, resulting in injury.

* YAMAHA logo printed on pipe is facing the opposite side.

Continued on the next page (on the back side)

Mounting the pads and the trigger module on the

rack system

Mount the pads and the trigger module on the rack system. Then position the kick pad and the hi-hat.

Mounting the TP65 (Drum pads) on the rack system

Figure 8: Pads Assembly-1 Figure 9: TP65

2 Attach the PCY65 (Cymbal pad) (@4) to the cymbal holder (@1) as shown in Figure 14. Attach

the felt washer ( Turn the wing nut until you are certain that the cymbal pad is attached. The cymbal pad is designed to shake when you hit the surface, even when the wing nut is tightened securely.

@3) and the wing nut (@2) removed in step 1, and tighten it.

Mounting the DTXPL (Trigger module)

Figure 15: Pads Assembly-4 Figure 16: Module stand-1

Attaching the FP6110A (Foot pedal) to KP65 (Kick pad)

Figure 21: FP6110A and KP65 Figure 22: T-handlet bolt

Figure 28: Diagram of standard connection

Clamp bolt

TP65 (Rear side)

1 See Figure 9.

Attach the clamp bolts (

Figure 10: Pads Assembly-2

) on TP65s (!2). Tighten the clamp bolts  ve to six turns each.

2 See Figure 10.

Loosen the knob (shown with holder inward as shown in the close-up illustration (m). Then tighten the knob and attach the tom holder

 rmly at a position where it points slightly downward.

Figure 11: Tom Holder and Drum Pad

) of the tom holder on the middle left. Move the tom

Tom holder

Clamp bolt

3 Attach the TP65 (Drum pad) to the tom holder as shown in Figure 11. Tighten the clamp

bolt and attach the drum pad TP65  rmly.

4 See Figure 10 again. Loosen the knob (shown with ) of the tom holder on the upper

left. Move the tom holder inward as shown in the close-up illustration (n). Then tighten the knob and attach the tom holder

 rmly at a position where it points slightly downward.

5 Attach the TP65 (Drum pad) to the tom holder . Tighten the clamp bolt and attach the

drum pad TP65  rmly.

6 Repeat step 4 and 5 in the same manner for tom holders and at the center of the rack

system and for tom holder holder.

on the right, and attach the TP65 (Drum pad) to each tom

Mounting the PCY65 (Cymbal pads) on the rack system

Figure 12: Pads Assembly-3 Figure 13: Cymbal holder-1

Cymbal holder

Wing nut

Felt washer

1 See Figure 13. Remove the wing nut (

holder (

Figure 14: Cymbal holder-2

) and one of the felt washers (@3) from the cymbal

Module stand

Clamp

1 See Figure 16. Loosen the knob of the clamp (@6) (shown with ) and remove the module

stand (

@5) from the clamp (@6).

Figure 17: Module stand-2

Fastening screw*

DTXPL (Rear side)

*  e fastening screws are included in the same plastic bag that includes the Assembly Manual of rack system

RS40.  e plastic bag is packaged between the space within the cardboards used for cushioning.

2 Tighten the fastening screws (@7) with a Phillips screwdriver, as shown in Figure 17, to

attach the module stand (

Figure 18: Module stand and clamp

@5) onto the rear side of the trigger module (@8).

DTXPL + Module stand

Clamp

Knob

3 Attach the module stand (@9) onto the clamp (#0). Tighten the knob (#1) and  x the

position.

Assembling the KP65 (Kick pad)

1 If a drum mat (sold separately) is not available, lay a cardboard on the  oor to prevent

scratching the surface.

Figure 19: KP65 Assembly

Body

Base

Wing bolt

Spring washer

Washer

2 Remove the wing bolt (#5), the spring washer (#6) and the washer (#7) from the body (#3),

and keep the four sets nearby in the order removed.

* If the wing bolt, the spring washer and/or the washer are separated from each other, set

them as illustrated in Figure 19-(a).

3 Set the base (#4) on the body (#3), and attach them using the wing bolt, the spring washer

and the washer removed in step 2.

Assembling the FP6110A (Foot pedal)

1 If a drum mat (sold separately) is not available, lay a cardboard on the  oor to prevent

scratching the surface.

Figure 20: FP6110A Assembly

FP6110A (Foot pedal)

KP65 (Kick pad)

T-handlet bolt

1 Turn the T-handlet bolt (%3) of the foot pedal (%1) in a counterclockwise direction and

loosen it.

Figure 23: Attaching FP6110A Figure 24: Adjustment

Hoop clamp

Convex part

Beater head

Pedal

2 Attach the convex part (%5) of the kick pad to the

hoop clamp (

%4).

3 Turn the T-handlet bolt (%3) in a clockwise direction

and tighten it.

4 Step on the pedal and check if the head of the beater

hits the center area of the kick pad. Adjust the length of the beater and/or position the pedal to the right or left if necessary.

Installing the HH65(Hi-hat controller) and KP65 (Kick pad)

Figure 25: Hi-Hat and KP65

1 If a drum mat (sold separately) is not available,

lay a cardboard on the  oor to prevent scratching the surface.

2 Place the HH65 (Hi-hat controller) (^2) under

the TP65 (Hi-hat cymbal) (

^1).

3 Place the KP65 (Kick pad) with FP6110A (Foot

pedal) (

^3) at the bottom center of the RS40

(rack system).

TP65 (Hi-hat cymbal)

HH65 (Hi-hat controller)

KP65 (Kick pad)+ FP6110A (Foot pedal)

Connecting the pads to the Trigger Module

Connect the output jacks of the pad and the input jacks of the trigger module with the 9-channel snake cable.

Figure 26: DTXPL (Rear panel)

Figure 27: 9-channel Snake Cable

* Each straight plug is labeled indicating the input jacks to which they are to be connected.

1 Insert the straight plugs (Figure 27-(a)) of the 9-channel snake cable into the input jacks on

the rear panel of the trigger module. For standard assembly, connect the straight plugs to the input jacks in accordance with the indication on each label.

2 Insert the L-shaped plugs (Figure 27-(b)) of the 9-channel snake cable into each

corresponding pad. It is recommended to connect the cables in order from numbers

o shown in Figure 28 (from the shortest cable to the longest cable).

Connecting to a power source

Connect the AC adaptor to the DTXPL.

Figure 29: Power switch (DTXPL rear panel)

Power supply jack (DC IN 12V)

Cable clip

Power switch

Figure 30: Cable clip (DTXPL rear panel)

Figure 31: Using Cable Band

* To check the actual sound, connect the unit with an ampli ed speaker or a headphone before turning on the

power.

Make sure to turn the power o (the Standby/

On switch (

) is set to the standby position).

2 Attach the AC adaptor to connect to a power

source. Insert the DC plug into the power supply jack (

&1) and twist the cable around the cable clip

(

&2) to prevent the DC plug from falling out.

3 Use the cable bands to bind the cables to the

pipes at the six points shown with the circles.

* Leaving the cable slacked may inter-

fere with your performance.

The assembly is now completed.

q to

Beater

Beater locking bolt

Radius rod

PCY65 (Cymbal pad)

2 Insert the radius rod ($3) into the hole of the frame as shown in Figure 20.

Drum key

3 Insert the beater ($1) into the hole of the beater attachment part until the further end of the

beater slides outward about 15 mm. Tighten the beater locking bolt (

$4).

(

$2) using the drum key

U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation

WS41160

Printed in Indonesia

********.*-****