Yaesu FTM-10R OPERATING MANUAL
VHF/UHF DUAL BAND FM TRANSCEIVER
FTM-10R
OPERATING MANUAL
VERTEX STANDARD CO., LTD.
4-8-8 Nakameguro, Meguro-Ku, Tokyo 153-8644, Japan
VERTEX STANDARD
US Headquarters
10900 Walker Street, Cypress, CA 90630, U.S.A.
YAESU EUROPE B.V.
P.O. Box 75525, 1118 ZN Schiphol, The Netherlands
YAESU UK LTD.
Unit 12, Sun Valley Business Park, Winnall Close
Winchester, Hampshire, SO23 0LB, U.K.
VERTEX STANDARD HK LTD.
Unit 5, 20/F., Seaview Centre, 139-141 Hoi Bun Road,
Kwun Tong, Kowloon, Hong Kong
VERTEX STANDARD (AUSTRALIA) PTY., LTD.
Normanby Business Park, Unit 14/45 Normanby Road
Notting Hill 3168, Victoria, Australia
Features ............................................................. 1
Front Panel & Top Panel ................................. 4
Rear Panel & LCD ........................................... 6
Accessories & Options ...................................... 8
Supplied Accessories ..................................... 8
Optional Accessories ...................................... 9
Installation ...................................................... 10
Preliminary Inspection ................................. 10
Installation Tips ............................................ 10
Safety Information ........................................ 11
Mobile Installation ....................................... 12
Base Station Installation ............................... 14
Antenna Considerations ............................... 15
Separate Installation ..................................... 16
Non-Separate Installation ............................. 21
Basic Operation .............................................. 22
Receive ......................................................... 22
Transmission ................................................ 23
Smart Menu Features ..................................... 24
AF Dual Function ......................................... 25
TM
ARTS
........................................................ 26
Dimmer function .......................................... 27
Horn Alert feature ........................................ 27
Intercom Function ........................................ 28
Monitor feature ............................................. 28
Public Address feature ................................. 29
Reverse feature ............................................. 29
Scan feature .................................................. 30
Smart Search
TM
Operation ............................ 30
Squelch Level Adjust ................................... 31
TCALL ......................................................... 32
TX Power Select .......................................... 32
Intercom Volume Control ............................ 32
Memory Operation ......................................... 33
Memory Storage ........................................... 33
Memory Recall ............................................. 34
Memory Channel Customization .................. 35
Memory Group Bank ............................... 36
Memory Channel Number Change .......... 37
Memory Channel Sort .............................. 37
Labeling Memory ..................................... 38
Scan Type ................................................. 39
Skip/Preferential Scan Setting ................. 39
Squelch Level ........................................... 40
CTCSS frequency .................................... 40
DCS code ................................................. 41
CTCSS/DCS Operation ........................... 41
Storing Independent Transmit
Frequency (Odd Split) ....... 42
Transmitter Power Level .......................... 43
Deleting Memory ..................................... 43
Club Channel Operation ................................ 44
Recalling the Club Channel ......................... 44
Activating the Club Channel Monitor .......... 44
Message Feature ............................................. 46
Programming a Message .............................. 46
Programming a Member List ........................ 47
Cloning the Message .................................... 48
Set your Personal ID .................................... 49
Sending Messages ........................................ 49
Cloning ......................................................... 50
Changing the Club Channel frequency ........ 52
Clock/Timer Operation .................................. 53
Set up the Clock ........................................... 53
Displays the Current Time ........................... 54
Contents
Using the Stop Watch Timer ........................ 55
Using the Interval Timer .............................. 55
Convenience Features .................................... 56
MUTE feature .............................................. 56
LOCK ........................................................... 56
Automatic Audio Volume Controller ........... 56
AF-VFO feature ........................................... 57
VOX Operation ............................................ 57
VOX Sensitivity ........................................... 58
Listening to AM/FM Broadcast Station ....... 58
Time-Out Timer (TOT) ................................ 58
Listening to external audio input .................. 59
Bluetooth
®
Operation ................................... 60
AF Dual Function ........................................... 62
CTCSS Operation ........................................... 64
DCS Operation ............................................... 65
EPCS (Enhanced Paging &
Code Squelch) Operation ............ 66
Internet Connection Feature (WiRES
TM
) ..... 68
DTMF Autodialer ........................................... 71
Repeater Operation ........................................ 73
Band Expansion .............................................. 74
Weather Broadcast Channel Operation ....... 75
Miscellaneous Setting ..................................... 76
Channel Step Selection ................................ 76
Changing the Operating Mode ..................... 76
PTT key function .......................................... 77
Key Beeper ................................................... 77
Smart Key Select .......................................... 77
Repeater Shift Direction ............................... 78
Repeater Shift Offset .................................... 78
Automatic Repeater Shift ............................. 78
Programming the Key Assignments ............. 79
Scanning Band ............................................. 80
Scan-Resume Mode ...................................... 80
Scan Direction .............................................. 81
Scan Start Direction ..................................... 81
Split Tone Operation .................................... 82
CTCSS/DCS/EPCS Bell Operation ............. 82
Battery Voltage Display ............................... 83
Temperature Display .................................... 83
Clock Format ................................................ 83
Time System ................................................. 84
Alarm Set ...................................................... 84
Interval Beep ................................................ 84
Automatic Power-Off (APO) ....................... 85
Audio Pitch Control ..................................... 85
Volume Setting Alert feature ....................... 86
Speaker Selection ......................................... 86
Stereo/Monaural Selection ........................... 87
MIC Gain Setting ......................................... 87
PTT Lock ..................................................... 87
Menu (“Set”) Mode ........................................ 88
Appendix ....................................................... 101
MH-68
B6J Microphone ............................... 101
MH-68A6J Microphone ............................... 101
Installation of Optional Accessories ............ 102
Microphone Jack “MEK-M10” .................. 102
BU-1 Bluetooth
CAB-1 Bluetooth
®
Adapter Unit ................ 104
®
Head Set
Charger Sleeve ...... 106
Reset Procedure ............................................ 107
Troubleshooting ............................................ 108
Specifications ................................................ 109
FEATURES
New Concept in Ultra compact Mobile transceivers
The ultra small size and design of this radio gives you many choices for mounting and
using this radio in your vehicle. The front panel may be separated from the main unit providing many placement and mounting options even for motor cycles or off road vehicles.
The microphone and the PTT switch are installed on the front panel so you can transmit
without connecting any microphone. You will not need an additional microphone or cable
to interfere with your driving on the road.
Simple set-up and no microphone or curl cord needed
The one touch, quick release front panel holder (new type) and the mounting bracket allow
you to place the front panel anywhere you want. The newly designed mobile mounting
bracket allows you to install or release the radio very easily.
The front panel has a magnet and it is possible to install it without using screws.
An angled panel adapter is included. The front panel may be adjusted up to 30 degrees
inclination to allow an improved, comfortable operating position.
Convenient Operation
The large function dial and key buttons afford simple operation, even while wearing driving gloves. The shape, size and position of the keys have been studied carefully. The design
will help avoid miss-operation of the keys while operating the vehicle.
Water proof front panel
The front panel is engineered to IP57 waterproof standards. You can mount the panel on the
handle bar of a motorcycle.
Superb visibility with new LCD panel
The bright LED and the Ocean Blue color LCD assure comfortable viewing night or day.
1FTM-10R OPERATING MANUAL
FEATURES
Great new options to optimize your Motor Sports activities
-- Hands free operation with optional Bluetooth® headset-When the optional Bluetooth® stereo headset is used with the optional Bluetooth® unit
and charger sleeve, you can enjoy comfortable hands free operation while you are driving.
Using the high audio output external speaker, the magnetic mounting brackets and the
Bluetooth® unit can provide hands-free operation and unlimited possibilities when using
this radio in any Motor Sports activity.
Reliable and advanced performance
The final transmitter amplifier produces up to 50 watts VHF and 40 watts UHF of reliable
and stable high power RF output.
The radio has wide receiving frequency capability, and an independent AM/FM broadcast
receiver. The Amateur radio receiver is specially designed for optimal Amateur band operation, with improved adjacent channel selectivity and IMD performance. You will appreciate the superior performance of the receiver when operating in strong electro magnetic
signal environments. The rugged chassis construction provides great reliability in any environment you may encounter on the car or the bike.
Loud Audio operation
A 2 inch speaker is mounted inside of the radio to provide powerful, low distortion AF
output. The high volume will give excellent audio recognition, even in very noisy environments.
Also available is a MLS-200-M10 optional external speaker. You can have loud audio
output with the 8 Watt AF amplifier built into the radio.
Sturdy rear chassis
A large aluminum die cast chassis forms a very sturdy rear case, and effectively radiates the
heat from the RF amplifier without the need of a cooling fan. The sandwich construction of
the chassis shields the electrical circuits from alternator and ignition noise. You have worry
free operation during long hours of rough handling in harsh environments.
Advanced features to support many Motor Sport activities.
U 500 memory channels with alpha-numeric labels.
U High output audio amplifier and optional external loudspeaker.
U The PA (Public Address) function permits communicating with a loud voice.
U The Intercom function provides communication through headphones between passen-
gers in the vehicle. Also the Bluetooth® unit can be used for the intercom.
U An AM /FM broadcast receiver is included. Audio line input is provided for connection
to your iPod® (FM broadcast and external input have stereo audio available)
U AF preset function alerts you when the AF audio level is changed by accident. You
enjoy the appropriate and optimized setting of volume level.
2 FTM-10R OPERATING MANUAL
FEATURES
U The message send/receive function permits sending a programmable 16 character mes-
sage with the transmitter’s ID. You can send your words by “Message” function even
when the noise level at the opposite station is too high for audio communication.
U The wireless clone feature permits the settings and data of the radio to be duplicated in
other radios without connecting any wires. All the radios in your group traveling together can have the same settings with the easy cloning operation.
U A convenient stopwatch function and display includes a Lap counter, Interval Timer/
Alert and Time.
U VOX is installed for hands free operation.
U Many new features include: Tone Control, One-touch band selection, Automatic audio
level control, Dimmer, TOT, WiRES, DC supply voltage indication, and APO.
3FTM-10R OPERATING MANUAL
FRONT PANEL & TOP PANEL
/ keys
These keys select the following operations.
• AF Dual Feature (See page 25) • Reverse (See page 29)
• ARTS Feature (See page 26) • Scan Operation (See page 30)
• Display Dimmer (See page 27) • Smart Search Operation (See page 30)
• Horn Alert Feature (See page 27) • Squelch Threshold Level (See page 31)
• Intercom Operation (See page 28) • TCALL (See page 32)
• Monitor Feature (See page 28) • TX Power Level (See page 32)
• Public Address (See page 29)
• Volume Level Control while Intercom Operation (See page 32)
PTT keys
Press this key to transmit.
Speak into the microphone while pressing this key.
P Release this key to return to receive.
P You may change this key function to “toggle”
mode (toggle the “transmit” and “receive” mode
each time the key is pressed). (See page 77)
MIC
TX/BUSY Indicator
This indicator glows green when a signal is
received.
This indicator glows red during transmission.
This indicator blinks blue when a message is
received.
This indicator glows white when transmitting
a message.
The internal microphone is located
here. Speak into the grill in a normal
voice level while pressing the PTT key.
VOL/SEL key
You may adjust the receiver audio level with the DIAL knob after pressing this key.
P The LED to the left of the DIAL knob will glow red when the DIAL knob is set to control
the receiver audio level.
P Press this key again or wait for three seconds, to cancel control of the audio level by the
Dial knob.
Mute Function:
Press and hold this key for one second to temporarily mute the receiver audio.
Press this key again to restore the receiver audio.
4 FTM-10R OPERATING MANUAL
FRONT PANEL & TOP PANEL
key
Press this key to activate the
function that is selected by the
/ keys.
POWER key
Press and hold this key for two seconds to toggle the
transceiver’s power on or off.
Lock Function:
Press this key momentarily while the transceiver is
turned on to toggle the key lockout feature on or off.
P You may also lock out the PTT key when the
LOCK mode is activated, by changing Menu Item
“F22 PTT LOCK”. See page 87.
key
P This key switches frequency control between the
VFO and Memory System.
P In the VFO mode, press and hold this key for one
second to enter the Memory Write mode and then
press this key again to store the frequency into
the memory.
P In the Memory mode, press and hold this key for
one second to enter the Memory Channel
Customization mode.
DIAL knob
P Selects the operating frequency and also selects
the memory channel.
P Adjusts the receiver audio level when the LED to
the left of the DIAL knob glows red.
P Select the Smart Menu Item and parameter when
the Smart Menu is activated.
LED
P This LED glows red when adjusting the receiver audio level
with the DIAL knob.
P This LED blinks orange when the Volume Setting Alert fea-
ture is active.
P This LED blinks yellow when the Timer feature is active.
keys
P Press these keys to switch the operating band as follows:
2 m Amateur Band 430 MHz Amateur Band FM BC Band AM BC Band
WX Band Audio Line Group Channel 2 m Amateur Band
P Press and hold this key for one second (MHz digits will blink), then rotate the DIAL
knob to change the frequency in 1 MHz steps.
5FTM-10R OPERATING MANUAL
REAR PANEL & LCD
S- & PO Meter
Operating band
Club Channel Monitor
Feature Active
Operating Frequency
Stereo Audio
Digital Code Squelch (DCS) Operation
CTCSS OperationRepeater Shift Direction
Volume level
DTMF Feature Active
Internet Connection
Feature Active
Memory Mode Selected
DC 13.8 V Cable Pigtail w/Fuse
Connect this pigtail to the car battery directly with the supplied DC cable.
P Connect the red lead to the positive side (+) of the battery and connect the
black lead to the negative side (-) of the battery. The DC cable is as short as
possible, because transmitting requires a high DC electrical current flow.
P Performance may be significantly reduced when connecting the DC cable
to the cigarette lighter plug or fuse box.
P Install a line filter if your vehicle has objectionable alternator noises.
ANT jack
Connect an efficient 144/430 MHz antenna, which is adjusted to 50-Ohm impedance. Use low-loss 50-Ohm coaxial
cable with type-M (PL259) connector.
You may connect an optional
®
CAB-1 Bluetooth
Head Set
Charger Sleeve here.
You may connect an optional
MEK-M10 Microphone Jack
here.
6 FTM-10R OPERATING MANUAL
MIC jack
You may connect an optional MH-68A6J or MH-
B6J Hand Microphone to this jack if you use.
68
EXT SPK jack
This 3-contact 3.5-mm mini stereo-phone jack provides receiver audio output for an optional external speaker. The audio impedance is 4 Ohms, and
the level varies according to the setting of the front
panel VOL control.
P Inserting a plug into this jack disables audio from
the transceiver’s internal speaker.
P When stereo speakers are connected to this jack,
and the Menu item “F42 STEREO” is set to “STE-
REO”, you may enjoy FM Broadcast audio, or
the external audio from the LINE IN jack in stereo.
P If there is no audio output from the external
speakers when connected to this jack, confirm
that the Menu item “F34 SPEAKER” is set to
“REAR” (See page 86).
P Use of a sound isolating headset while driving
on public roads is not lawful. An open type headset must be used for safety.
Hint: Menu Mode
The FTM-10R Menu enables the configuration of
49 transceiver parameters to your favorite settings.
REAR PANEL
LINE IN jack
Connect an external audio source (such as the iPod
jack using the after-market audio cable.
When using the audio line input to this jack, you may enable
the receiving of amateur signals while listening to your favorite music.
Adjust the input level with the volume control of the external
audio equipment connected.
The connection cable depends on the external audio equipment
you connect. Please ask your dealer.
®
) to this
7FTM-10R OPERATING MANUAL
ACCESSORIES & OPTIONS
SUPPLIED ACCESSORIES
U9900222 (2 pcs)
CP8850001
Mobile Mounting Bracket DC Power Cord W/Fuse
(T9021715)
Angle Adapter
(RA0886300)
Separation Cable (3 m)
(T9207411)
Spare Fuse (15 A)
(Q0000151) (2 pcs)
U30520020
RA0946700
S5000296
Magnet
U40412220
(2 pcs)
Front Panel Bracket
RA0458800
RA0930900
Front Panel Hanger
U51510020
Speaker Cable
(T9101574)
Hex Wrench (4 mm) (S5000218)
Hex Wrench (3 mm) (S5000297)
Operating Manual
Warranty Card
8 FTM-10R OPERATING MANUAL
ACCESSORIES & OPTIONS
OPTIONAL ACCESSORIES
MH-68A6J
DTMF Microphone
MMB-M10
Multi-Angle Bracket
BH-1
Bluetooth® Headset
FEP-4
Ear Phone for BH-1
MH-68B6J
Normal Microphone
MMB-M11
Handle Bar Bracket
BU-1
Bluetooth® Adapter Unit
CT-M11
Connection Cable
MEK-M10
Microphone Jack
Separation Cable (6 m)
Bluetooth® Headset
MLS-200-M10
High-Power External
Speaker
CT-M10
CAB-1
Charger Sleeve
Availability of accessories may vary in some regions. This product is designed to perform
optimally when used with genuine Vertex Standard accessories. Vertex Standard shall not
be liable for any damage or accidents such as fire, leakage or explosion of batteries, etc.,
caused by the malfunction of non-Vertex Standard accessories. Consult your Vertex Standard dealer for details on these and any future available options. Connection of any nonVertex Standard-approved accessory, should it cause damage, may void the Limited Warranty on this apparatus.
9FTM-10R OPERATING MANUAL
INSTALLATION
This chapter describes the installation procedure for integrating the FTM-10R into a typical amateur radio station. It is presumed that you possess technical knowledge and conceptual understanding consistent with your status as a licensed radio amateur. Please take some
extra time to make certain that the important safety and technical requirements detailed in
this chapter are followed closely.
PRELIMINARY INSPECTION
Inspect the transceiver visually immediately upon opening the packing carton. Confirm
that all controls and switches work freely, and inspect the cabinet for any damage. Gently
shake the transceiver to verify that no internal components have been shaken loose due to
rough handling during shipping.
If any evidence of damage is discovered, document it thoroughly and contact the shipping
company (or your local dealer, if the unit was purchased over-the-counter) so as to get
instructions regarding the prompt resolution of the damage situation. Be certain to save the
shipping carton, especially if there are any punctures or other evidence of damage incurred
during shipping. If it is necessary to return the unit for service or replacement, use the
original packing materials. Then put the entire package inside another packing carton to
preserve the evidence of shipping damage for insurance purposes.
INSTALLATION TIPS
To ensure long life of the components, be certain to provide adequate ventilation around the
cabinet of the FTM-10R.
Do not install the transceiver on top of another heat-generating device (such as a power
supply or amplifier). Avoid heating vents and window locations that could expose the transceiver to excessive direct sunlight, especially in hot climates. The FTM-10R should not be
used in an environment where the ambient temperature exceeds +140 °F (+60 °C).
10 FTM-10R OPERATING MANUAL
INSTALLATION
SAFETY INFORMATION
The FTM-10R is an electrical apparatus, as well as a generator of High RF (Radio Frequency) energy. You should exercise all safety precautions that are appropriate for this type
of device. These safety tips apply to any device installed in a well-designed amateur radio
station.
Never allow unsupervised children to play in the vicinity of your transceiver or
antenna installation.
Be certain to wrap any wire or cable splices thoroughly with insulating electrical
tape, to prevent short circuits.
Do not route cables or wires through doorjambs or other locations where they may
become frayed and shorted to ground or to each other.
Do not stand in front of a directional antenna while you are transmitting into that
antenna. Do not install a directional antenna in any location where humans or pets
may walk in the main directional lobe of the antenna's radiation pattern.
In mobile installations, it is preferable to mount the antenna on top of the vehicle, if
feasible, this will utilize the car body as a counterpoise and raise the radiation pat-
tern as far away from passengers as possible.
During mobile operation when stopped (in a parking lot, for example), make it a
practice to switch to Low power if there are people walking nearby.
Never wear dual-earmuff headphones while driving a vehicle.
Do not attempt to drive your vehicle while making a telephone or auto patch call
while using the optional DTMF microphone. Pull over to the side of the road, whether
dialing manually or using the auto-dial feature.
Warning!: High RF voltage is present in the TX RF section of the transceiver while trans-
mitting. Do not touch the TX RF section while transmitting.
11FTM-10R OPERATING MANUAL
INSTALLATION
MOBILE INSTALLATION
The FTM-10R must only be installed in vehicles having a 13.8 Volt negative ground electrical system. Mount the transceiver where the display, controls, and microphone are easily
accessible, using the supplied Mobile Mounting Bracket.
The transceiver may be installed in almost any location, but should not be positioned near
a heating vent or anywhere where it might interfere with driving (either visually or mechanically). Make sure to provide plenty of space on all sides of the transceiver so that air
can flow freely around the radio’s case.
An antenna and an antenna cable are not included in the box. Purchase them separately to
accommodate your transceiver installation.
U The DC power cable draws a large current when transmitting. The power cable should
be wired as short as possible, and connected directly to the battery. (Do not use the
cigarette lighter socket for power connections).
U Never remove the fuse holders from the DC cables
U Never connect the transceiver directly to a 24 V battery.
U Select a low-loss coaxial cable to connect the transceiver with the antenna. Use the
shortest length possible.
U Select a quality, high efficiency VHF/UHF antenna, and mount it in a good location on
the car to obtain the maximum performance from the transceiver. (NOTE: An antenna
designed with a matching device that forms a low DC resistance to ground may have
poor reception on the AM broadcast band.)
U The antenna depends on good grounding to realize maximum performance. Contact
your dealer for information on transceiver and antenna installation.
U If alternator noise exists, use a line filter in the DC power cable connection.
IMPORTANT: Select a location which can support the weight of the FTM-10R trans-
ceiver and does not interfere with your driving.
12 FTM-10R OPERATING MANUAL
INSTALLATION
Mobile Power Connections
To minimize voltage drop and avoid blowing the vehicle's fuses, connect the supplied DC
power cable directly to the battery terminals. Do not attempt to defeat or bypass the DC
cable fuse - it is there to protect you, your transceiver, and your vehicle's electrical system.
Warning!
Never apply AC power to the power cable of the FTM-10R, nor DC voltage greater
than 15.8 Volts. When replacing the fuse, use only a 15-A fuse. Failure to observe
these safety precautions will void the Limited Warranty on this product.
U Before connecting the transceiver, check the voltage at the battery terminals while rev-
ving the engine. If the voltage exceeds 15 Volts, repair the vehicle’s voltage regulator
before proceeding with installation.
U Connect the RED power cable lead to the POSITIVE (+) battery terminal, and the
BLACK power cable lead to the NEGATIVE (-) terminal. If you need to extend the
power cable, use #12 AWG or larger insulated, stranded copper wire. Solder the splice
connections carefully, and wrap the connections thoroughly with insulating electrical
tape.
U Before connecting the cable to the transceiver, verify the voltage and polarity of the
voltage at the transceiver end of the DC cable using a DC voltmeter. Now connect the
transceiver to the DC cable.
FTM-10R
Cabin »¼ Engine Compartment
RED:Positive (+)
BLACK:Negative (-)
Battery
Mobile Speakers
The optional MLS-200-M10 High-Power External Speaker includes its own swivel-type
mounting bracket, and is available from your Yaesu dealer.
Other external speakers may be used with the FTM-10R, if they present the specified 8Ohm impedance and are capable of handling the 8 Watts of audio output supplied by the
FTM-10R.
13FTM-10R OPERATING MANUAL
INSTALLATION
BASE STATION INSTALLATION
The FTM-10R is ideal for base station use as well as in mobile installations. The FTM-10R
is specifically designed to integrate into your station easily, using the following information
as a reference.
AC Power Supplies
Operation of the FTM-10R from an AC line requires a power supply capable of providing
at least 9 Amps continuously at 13.8 Volts DC. The FP-1025A and FP-1030A DC Power
Supplies are available from your Yaesu dealer to satisfy these requirements. Other wellregulated power supplies may be used if they meet the above voltage and current specifications.
Use the DC power cable supplied with your transceiver to make power connections to the
power supply. Connect the RED power cable lead to the POSITIVE (+) power supply
terminal, and connect the BLACK power cable lead to the NEGATIVE (-) power supply
terminal.
14 FTM-10R OPERATING MANUAL
INSTALLATION
ANTENNA CONSIDERATIONS
The FTM-10R is designed for use with antennas presenting an impedance of near 50 Ohms
at all operating frequencies. To avoid damage that could result if transmission occurs accidentally without an antenna, the antenna (or a 50 Ohm dummy load) should be connected
whenever the transceiver is turned on.
Ensure that your antenna is designed to handle 50 Watts of transmitter power. Some magnetic-mount mobile antennas, designed for use with hand-held transceivers, may not be
capable of withstanding this power level. Consult the antenna manufacturer's specification
sheet for details.
Use high-quality 50-Ohm coaxial cable for the lead-in to your FTM-10R transceiver. All
efforts at providing an efficient antenna system will be wasted if poor quality, “lossy” coaxial cable is used. Losses in coaxial lines increase as the frequency increases, so an 8meter-long (25’) coaxial line with under 1 dB of loss at 144 MHz may have a loss of 3 dB
or more at 446 MHz. Choose your coaxial cable carefully based on the installation location
(mobile vs. base) and the overall length of the cable required. (For very short runs of cable
in a mobile installation, the smaller, more flexible cable types may be acceptable.)
For reference, the chart below shows approximate loss figures for typically available coaxial cables frequently used in VHF/UHF installations.
Loss in dB per 30 m (100 feet) for Selected 50-Ohm Coaxial Cables
(Assumes 50-Ohm Input/Output Terminations)
CABLE TYPE
RG-58A
RG-58 Foam
RG-213
RG-8 Foam
Belden 9913
Times Microwave LMR-400
7/8” “Hardline”
Loss figures are approximate; consult cable manufacturers’ catalogs for complete specifications.
LOSS: 144 MHZ
6.5
4.7
3.0
2.0
1.5
1.5
0.7
LOSS: 430 MHZ
> 10
8
5.9
3.7
2.9
2.6
1.3
In outdoor installations, be certain to weatherproof all connectors thoroughly, as water
entering a coaxial cable will cause losses to escalate rapidly, thus diminishing your communications effectiveness. The use of the shortest possible length of the highest quality coaxial
cable that fits within your budget will ensure the best performance from your FTM-10R.
Your dealer should be able to assist you with all aspects of your antenna installation requirements.
15FTM-10R OPERATING MANUAL
INSTALLATION
SEPARATE INSTALLATION
1. Remove the four screws securing the
Front Panel and then remove the Front
Panel from the Transceiver Body
(Figure 1).
2. Disconnect the 8-pin modular plug
from the Transceiver (Figure 2).
3. Remove the screw affixing the Straight
Sub Panel, and then remove the
Straight Sub Panel from the Front Panel
(Figure 3).
4. Remove the four screws securing the
Rear Case of the Front Panel and remove the Rear Case from the Front
Panel (Figure 4). Disconnect the Connector of the Connection Cable from
the Printed Circuit Board in the Front
Panel when you remove the Rear Case
(Figure 5).
5. Remove the Binding Plate from the
Rear Case (Figure 6-), and then pull
out the Connection Cable from the Rear
Case (Figure 6-).
Figure 1
Figure 2
Figure 3
Figure 4
connector
Figure 5
Figure 6
16 FTM-10R OPERATING MANUAL
SEPARATE INSTALLATION
6. Insert the supplied 3-m Connection
Cable from the rear side of Rear Case
(Figure 7-), and then attach the Connection Cable to the Rear Case using
the previously removed Binding Plate
(Figure 7-).
7. Attach the Connection Cable to the
Printed Circuit Board (Figure 8), and
then replace the Rear Case to the Front
Panel using the previously removed
four screws (Figure 9).
8. Connect the 8-pin modular plug of the
Connection Cable to the Transceiver
(Figure 10).
9. Mount the supplied Mobile Mounting
Bracket to the any position using the
supplied screws (Figure 11).
INSTALLATION
Figure 7
connector
Figure 8
Figure 9
Figure 10
Figure 11
17FTM-10R OPERATING MANUAL
INSTALLATION
SEPARATE INSTALLATION
Front Panel Installation
Use the supplied Front Panel Bracket
1. Mount the supplied
Front Panel Bracket to
any suitable position using the supplied screws.
Use the supplied Magnet
1. Connect the supplied Magnet and
Front Panel Hanger using the supplied screw.
2. Connect the supplied
Front Panel Hanger
using the supplied
screw.
Magnet
3. Install the Front Panel
into the Front Panel
Bracket.
2. Affix the supplied Protection Seal to
the Magnet.
Protection Seal
CAUTION!
PP
P If the protective film is not affixed to the magnet, it may damage the mounting
PP
surface.
PP
P Damage is possible even if the protection film is attached.
PP
PP
P Be careful handling the hanger. The strong magnet could pinch your fingers.
PP
PP
P Even with the strong magnet, it is possible to displace the bracket.
PP
PP
P The magnet may destroy data on banking & identification cards.
PP
18 FTM-10R OPERATING MANUAL
SEPARATE INSTALLATION
Use the Optional Multi-Angle Bracket “MMB-M10”
INSTALLATION
1. If you use the Front Panel as a Microphone, connect the supplied Front
Panel Hanger using the supplied
screw.
3. If you do not use the Front Panel as a
Microphone, install the Front Panel
directly to the “MMB-M10”.
2. Mount the supplied Front Panel
Bracket to the “MMB-M10” using the
supplied two screws.
Installation of the “MMB-M10”
Hex. Nut
M5x15
Spring Washer
Flat Washer
Spring Washer
M5x25
Flat Washer
Spring Washer
M5x25
19FTM-10R OPERATING MANUAL
INSTALLATION
SEPARATE INSTALLATION
Use the Optional Handle Bar Bracket “MMB-M11”
1. If you use the Front Panel as a Microphone, connect the supplied Front
Panel Hanger using the supplied
screw.
¯
3. Select the Bracket and Rubber to fit
the size of the Handle Bar (Refer to
the table below).
2. If you do not use the Front Panel as a
Microphone, install the Front Panel
directly to the “MMB-M11”.
Hex. Nut
M5x15
Spring Washer
Flat Washer
Spring Washer
M5x25
Rubber (S-a: t=1 mm)
Bracket (S)
Rubber (S-b: t=2 mm)
Bar Bracket Rubber
7/8”
1” S-a
1-1/4”
1-1/2” L-a
Rubber (L-a: t=1 mm)
S
L
Bracket (L)
Rubber (L-b: t=3 mm)
S-a & S-b
L-a & L-b
20 FTM-10R OPERATING MANUAL
INSTALLATION
NON-SEPARATE INSTALLATION
The FTM-10R front panel may be tilted using the supplied Angle Sub Panel.
1. Remove the four screws securing the
Front Panel and then remove the panel
from the transceiver body (Figure 1).
2. Disconnect the 8-pin modular plug
from the transceiver (Figure 2).
3. Remove the screw affixing the Straight
Sub Panel, and then remove the
Straight Sub Panel from the Front Panel
(Figure 3).
4. Attach the supplied Angle Sub Panel
to the Front Panel, using the previously
removed screw (Figure 4).
You may set this up in a “look-up” or
“look-down” configuration depending
on the mounting position of the Sub
Panel.
5. Connect the 8-pin modular plug to the
transceiver’s body.
6. Attach the Front Panel (with Angle Sub
Panel) to the transceiver’s body, using
the previously removed four screws
(Figure 5).
Figure 1
Figure 3
Figure 2
Figure 4
Figure 5
21FTM-10R OPERATING MANUAL
BASIC OPERATION
RECEIVE
1. To turn the transceiver on, press and hold in the top panel [POWER] key for two seconds.
When you turn the transceiver on, the applied DC voltage is displayed on the LCD for
2 seconds. Then the operating frequency will be displayed.
To turn the transceiver off, press and hold in the [POWER] key for two seconds.
2. Press the front panel / keys to switch the operating band as follows:
Key
£ 2 m Amateur Band (H-V) £ 430 MHz Amateur Band (H-U) £ FM BC Band (FM) £
AM BC Band (AM) £ WX Band (WX) £ Audio LineÚ £ Group Memory (GRP) £ 2
m Amateur Band (H-V) £
Key
2 m Amateur Band (H-V) £ Group Memory (GRP) £ Audio LineÚ £ WX Band (WX)
£ AM BC Band (AM) £ FM BC Band (FM) £ 430 MHz Amateur Band (H-U) £ 2 m
Amateur Band (H-V) £
Ú When external audio equipment, like an iPod®, is connected, an after-market cable is
required.
When external audio equipment is connected, the input audio level must be adjusted
on the external audio equipment.
H-U 430 MHz Amateur Band
H-V 144 MHz Amateur Band
GRP Group Memory
-- Audio Line
WX WX Band
AM AM BC Band
FM FM BC Band
[
VOL/SEL] key
/ key
[
POWER] key
DIAL knob
22 FTM-10R OPERATING MANUAL
BASIC OPERATION
3. Rotating the DIAL knob tunes the frequency in pre-programmed steps. Clockwise rota-
tion of the DIAL knob will increase the frequency; counter-clockwise rotation will lower
the operating frequency.
4. Press and hold in one of the front panel / keys for one second (the 1 MHz digit
will blink). Then rotate the DIAL knob to change the frequency at 1 MHz per step. This
feature is extremely useful for making rapid frequency excursions over the wide tuning
range of the FTM-10R.
5. Press the [VOL/SEL] key until the red LED to the left of the DIAL knob illuminates
and the volume level is displayed on the LCD. Now, the DIAL knob becomes the volume knob.
6. Rotate the DIAL knob to adjust the receiver volume. Clockwise rotation increases the
audio output level.
TRANSMISSION
1. Press the front panel / keys to switch the operating band to 144 MHz or 430
MHz band.
2. Press the PTT (Push To Talk) key on the front panel when the frequency is clear. Speak
into the microphone on the front panel (upper left corner of the front panel) in a normal
voice level.
When talking around 3 feet away from the front panel microphone, the modulation may
not be enough and the transmitted audio level may be lower.
3. When your transmission is complete, release the PTT key. The transceiver will revert to
the receive mode.
MIC
PTT key
23FTM-10R OPERATING MANUAL
SMART MENU FEATURES
The FTM-10R top panel / keys, and the key select and enable operation of the
following features:
Select the function
Display Function
AF DUAL Press the key to activate the AF Dual function which enables re-
ceiving an Amateur Band signal while listening to the signal of an FM
Broadcast Station at the same time.
ARTS Press the key to activate the ARTS feature.
DIMMER Press the key to enable adjustment of the display illumination level
by the DIAL knob.
HORN 1 Press the PTT switch to activate the sound of a Gong Bell.
HORN 2 Press the PTT switch to activate the sound of a UFO in flight.
HORN 3 Press the PTT switch to activate the sound of a klaxon.
HORN 4 Press the PTT switch to activate the sound of a siren.
INTERCOM Press the key to activate the Intercom mode.
MONI Press the key to disable noise and tone squelch.
PA Press the PTT switch to route your amplified voice through the PA
speaker.
REVERSE Press the key to activate the Reverse feature.
SCAN Press the key to activate the scanner.
SQL LEVL Press the key to enable adjustment of the noise squelch threshold
level by the DIAL knob.
SSCH Press the key to activate the Smart Search.
TCALL Press the key to activate the 1750 Hz Tone Burst.
TX POWER Press the key to change the transmit power level.
VOL.ITCOM Press the key to change the receiver audio level of the intercom
receiver.
[F]
key
Advice: When one of the above features does not appear in the list, it is because that feature
is not assigned to the top panel / keys. Please insure the Menu
“F14 FKEY MOD” is set to “FNC” or “FNC+MSG”.
24 FTM-10R OPERATING MANUAL
SMART MENU FEATURES
AF DUAL FUNCTION
With the “AF DUAL” function, it is possible to monitor your desired amateur band frequency while receiving AM, FM broadcast or Audio from the external input jack.
You may select: AM broadcast, FM broadcast, Club Channel or external line input, by
changing the Menu Item “F2 AF DUAL” (The factory default is AM broadcast receiving).
1. Set the FTM-10R to the desired amateur band frequency by the VFO or Memory chan-
nel selection.
2. Press the top panel / key to select “AF DUAL”.
3. Press the key to activate the AF Dual function.
P By first setting the desired VFO or memory channel in
step #1 above, and then starting “AF DUAL” function, both the amateur signals and
the AM broadcast station will be received.
4. Rotate the DIAL knob to select the desired AM Broadcast station.
P You may switch the AM Broadcast Band frequency control between the VFO and
Memory channel by pressing the key.
P When a signal is received in the amateur band, the AM Broadcast audio is muted.
When the amateur band signal drops, the AF Dual function is resumed (monitor the
amateur band frequency while receiving the AM broadcast).
P You may transmit on the frequency set in step1 by pressing the PTT key, even if the
AF Dual function is activated.
To disable the AF Dual function, press the front panel / keys.
P When the key function is set to “AF DUAL” via the
top panel / key, the key may be used to toggle
the “AF DUAL” on/off.
25FTM-10R OPERATING MANUAL
SMART MENU FEATURES
ARTSTM
The ARTS feature uses DCS signaling to inform both parties when you and another ARTS
equipped station are within communications range. This may be particularly useful during
Search and Rescue situations, where it is important to stay in contact with other members of
your group.
Both stations must set up their DCS codes to the same code number, then activate their
ARTS feature using the command appropriate for their radio. Alert ringers may be activated, if desired.
Whenever you push the PTT key, or every 25 seconds after ARTS is activated, your radio
will transmit a signal which includes a (subaudible) DCS code
for about 1 second. If the other radio is in range, the beeper
will sound (if enabled) and the display will show “IN.RANGE”,
otherwise the out of range display “OUT.RANGE” will be display during ARTS operation.
Whether you talk or not, the polling every 25 seconds will continue until you de-activate ARTS. When ARTS is de-activated,
DCS will also be deactivated (if you were not using it previously in non- ARTS operation).
If you move out of range for more than one minute (four pollings), your radio will sense
that no signal has been received. Three beeps will sound, and the display will revert to
“OUT.RANGE”. If you move back into range, your radio will again beep, and the display
will change back to the “IN.RANGE” indication.
(
Default “OFF”
)
During ARTS operation, your operating frequency will continue to be displayed, but no
changes may be made to it or other settings. You must terminate ARTS in order to resume
normal operation. This is a safety feature designed to prevent accidental loss of contact due
to channel change, etc.
1. Set the FTM-10R to the desired amateur band frequency by the VFO or Memory channel selection.
2. Set your radio and the other radio(s) to the same DCS code number per the discussion
on page 65.
3. Press the top panel / key to select “ARTS”.
4. Press the key. You will observe the “OUT.RANGE” display on the LCD. The ARTS
operation has now commenced.
5. Every 25 seconds, your radio will transmit a “polling” call to the other station. When that
station responds with its own ARTS polling signal, the display will change to “IN.RANGE”
to confirm that the other station’s polling code was received in response to yours.
6. When the key function is set to “ARTS” via the top panel / key, the key
may be used to toggle the “ARTS” on/off.
26 FTM-10R OPERATING MANUAL
SMART MENU FEATURES
DIMMER FUNCTION
You may adjust the display dimmer level.
1. Press the top panel / key to select “DIMMER”.
2. Press the key.
3. Rotate the DIAL knob to select a comfortable brightness
level.
DIMMER 1 ÅÆ DIMMER 2 ÅÆ DIMMER 3
DIMMER 4 ÅÆ DIMMER 5
ÅÆ
Dim Bright
Å
4. Within two seconds of selecting the brightness level, save the new setting and return to
the VFO or Memory Channel mode.
When the key function is set to “DIMMER” via the top panel / key, the
key is used as the Dimmer Level control key.
HORN ALERT FEATURE
The Horn Alert feature outputs one of four unique sounds to the transceiver’s speaker.
When an optional MLS-200-M10 External Speaker is connected, the FTM-10R transceiver may be used as an 8 watt Horn Alert.
1. Press the top panel / key to select one of the four functions described below:
HORN 1: Sounds a Gong Bell.
HORN 2: Sounds a flight sound of a UFO.
HORN 3: Sounds a klaxon.
HORN 4: Sounds an ambulance siren.
2. Press the key to activate the Horn Alert feature.
When the Horn Alert function is activated, the volume level
graphic will be displayed on LCD.
3. Press the PTT key.
U You may change the PTT key function via Menu Item “F23 PTT MODE”.
MOMENT: While pressing the PTT key, the audio is output from the speaker (fac-
tory default).
TOGGLE: Once the PTT key is pressed the audio is output from the speaker, and
when the PTT key is pressed once again, the audio output is off.
U The unique sound, which was selected in step 1 above, will be output from the speaker.
U The “HORN OUT” notation appears in the display while the Horn Alert is activated.
U Press the [VOL/SEL] key to adjust the volume (AF level) of the Horn Alert output.
While the RED LED is on, the volume level can be adjusted with the dial knob.
U To disable the Horn Alert feature, repeat steps 1 and 2 above.
ÅÆ
Æ
(
Default “OFF”
)
Graphic Bar
27FTM-10R OPERATING MANUAL
SMART MENU FEATURES
INTERCOM FUNCTION
Intercom operation is possible with the FTM-10R, by installing the optional Bluetooth
Adapter unit “BU-1” in the radio and using the optional Bluetooth® Headset “BH-1”.
When operating in a very noisy environment, (for example, a loud exhaust or engine noise,
or inside an off-road vehicle) communication with a fellow passenger is possible using the
Bluetooth® intercom feature.
1. Press the top panel / key to select “INTERCOM”.
2. Press the key to activate the Intercom function.
When the Intercom function is activated, the volume level
graphic will be displayed on LCD.
You may switch the receiver audio volume level between “High” and “Low” via the
“VOL.ITCOM” function described below.
When the Intercom function is activated, the internal speakers (front panel and main
chassis) are disabled.
To disable the Intercom function, repeat steps 1 and 2 above.
When set the key function to “INTERCOM” via the
top panel / key, the key to be used as the Intercom feature on/off key.
Important Notice!
Graphic Bar
®
Use of a sound-isolating headset while driving on public roads is not lawful and hazardous. An open type headset must be used for safety.
MONITOR FEATURE
The Monitor permits disabling the noise and tone squelch systems temporarily.
When the received signal is weak and the sound from the speaker is intermittent, use this
function to over-ride the squelch and hear the received signal.
1. Press the top panel / key to select “MONI”.
2. Press the key.
The noise and tone squelch are disabled while pressing the
key.
When the key function is set to “MONI” via the top panel / key, the key
may be used as the “Monitor” key.
28 FTM-10R OPERATING MANUAL
Loading...