Whirlpool W10679043A, W10755903A - SP Installation Instructions Manual

0 (0)

HybridCare™ Heat

Sécheuse à pompe à

Pump Dryer

Installation Instructions

Table of Contents

DRYER SAFETY.........................................................................2

INSTALLATION REQUIREMENTS ........................................... 2

Tools and Parts ...................................................................... 2

LOCATION REQUIREMENTS ...................................................3

DRAIN SYSTEM ......................................................................... 5

ELECTRICAL REQUIREMENTS - U.S.A. ONLY .....................5

ELECTRIC DRYER POWER HOOKUP - CANADA ONLY ...... 6

INSTALL LEVELING LEGS .......................................................7

ELECTRICAL INSTALLATION - U.S.A. ONLY ........................8

Power Supply Cord Connection ........................................... 8

Direct Wire Connection ....................................................... 11

CONNECT OUTLET HOSE ..................................................... 14

LEVEL DRYER ......................................................................... 14

COMPLETE INSTALLATION CHECKLIST ............................ 15

DOOR REVERSAL (OPTIONAL) ............................................. 16

TROUBLESHOOTING ............................................................. 22

chaleur HybridCare™

Instructions d’installation

Table des matières

SÉCURITÉ DE LA SÉCHEUSE ............................................... 23

EXIGENCES D’INSTALLATION .............................................. 23

Outillage et pièces ............................................................... 23

EXIGENCES D’EMPLACEMENT ............................................ 24

SYSTÈME DE VIDANGE .......................................................... 26

SÉCHEUSE ÉLECTRIQUE RACCORDEMENT À L’ALIMENTATION ÉLECTRIQUE -

CANADA SEULEMENT ........................................................... 26

INSTALLATION DES PIEDS DE NIVELLEMENT ..................27

CONNEXION DU TUYAU DE SORTIE ...................................27

RÉGLAGE DE L’APLOMB DE LA SÉCHEUSE ...................... 28

ACHEVER L’INSTALLATION LISTE DE VÉRIFICATION ......29

INVERSION DE LA PORTE (FACULTATIF) ...........................30

DÉPANNAGE .................................... COUVERTURE ARRIÈRE

Para una version de estas instrucciones en español, visite www.Whirlpool.com or www.maytag.com

INSTALLATION NOTES

Date of purchase: _________________________________ Date of installation: _______________________________ Installer: ________________________________________ Model number: ___________________________________ Serial number: ___________________________________

NOTES CONCERNANT L’INSTALLATION

Date d’achat : _____________________________________ Date d’installation : ________________________________ Installateur : ______________________________________ Numéro de modèle : ________________________________ Numéro de série : __________________________________

W10679043A W10755903A - SP

Dryer Safety

Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing.

Service Personnel – Do not contact the thermostat bracket while the appliance is energized.

IMPORTANT: When discarding or storing your old clothes dryer, remove the door.

Installation Requirements

TOOLS AND PARTS

Gather the required tools and parts before starting installation.

Tools needed:

Flat-blade screwdriver #2 Phillips screwdriver

Wire stripper (direct wire installations)

Channel locks

Location Requirements

Check code requirements. Some codes limit, or do not permit, installing dryer in garages, closets, mobile homes, or sleeping quarters. Contact your local building inspector.

1/4" and 5/16" nut driver (recommended)

Adjustable wrench that opens to 1" (25 mm) or hex-head socket wrench

Utility knife Tape measure

Level

Pliers

Parts supplied:

Leveling legs (4)

6' (1829 mm) drain hose with couplers

You will need:

■ A separate 30 amp circuit.

■ If using power supply cord, a grounded electrical outlet

located within 2 ft. (610 mm) of either side of dryer. See

“Electrical Requirements.”

■ Floor must support dryer weight of 200 lbs. (90.7 kg). Also

consider weight of companion appliance.

■ Level oor with maximum slope of 1" (25 mm) under entire

dryer. If forward slope is greater than 1" (25 mm), water could

run out from front of lter. Install Extended Dryer Feet Kit, Part

Number 279810. If not level, clothes may not tumble properly

and automatic sensor cycles may not operate correctly.

■ For garage installation, place dryer at least 18" (460 mm)

above oor. If using a pedestal, you will need 18" (460 mm)

to bottom of dryer.

■ The dryer must not be installed or stored in an area where it

will be exposed to water and/or weather. IMPORTANT: Do not operate, install, or store dryer where

it will be exposed to water, weather, or at temperatures below 40° F (4° C). Lower temperatures may cause dryer not to shut off at end of automatic sensor cycles, resulting in longer drying times.

Cable ties (2)

Parts package is located in dryer drum. Check that all parts are included.

NOTE: Do not use leveling legs supplied with dryer if installing with a pedestal or a stack kit.

If using a power supply cord:

Use a UL listed power supply cord kit marked for use with clothes dryers. The kit should contain:

■ A UL listed 30-amp power supply cord, rated 120/240 volt

minimum. The cord should be type SRD or SRDT and be at least 4 ft. (1.22 m) long. The wires that connect to the dryer must end in ring terminals or spade terminals with upturned ends.

■ A UL listed strain relief.

Additional Accessories: (Not supplied with dryer)

Refer to your Use and Care Guide for information about accessories available for your dryer.

DRYER DIMENSIONS

Front view:

383/4" Min.

(984 mm)

39" Max.

(990 mm)

27"

(686 mm)

Side view:

Installation spacing for recessed area or closet installation

All dimensions show recommended and minimum spacing allowed.

■ Additional spacing should be considered for ease of

installation and servicing.

■ Additional clearances might be required for wall, door, oor,

moldings, and drain system.

■ Additional spacing should be considered on all sides of the dryer

to reduce noise transfer.

■ For closet installation, with a door, minimum ventilation openings

in the top and bottom of the door are required. Louvered doors

with equivalent ventilation openings are acceptable.

■ Companion appliance spacing should also be considered.

Recommended installation clearances (dryer only):

18" min.

(457 mm)

(76 mm)

48 in.2 min.

(310 cm

)

Back view:

61/2"

(165 mm)

NOTE: Allow clearance behind dryer for proper drain hose routing and cooling fan ventilation. Push dryer back as far as possible and make sure drain hose is not crushed or kinked.

* Approx. measurement.

Power cord/

cable

Water

Cooling

drain

131/2"

(343 mm)

fan

(759 mm)

/2"

(165 mm)

/8"*

IMPORTANT: Do not block cooling fan as your dryer may not operate properly.

(127 mm)

(25 mm)

(76 mm)

(25 mm)

NOTE: 0" ( 0 mm) spacing is allowed behind dryer, providing drain hose is not kinked or pinched.

24 in.2 min.

(155 cm2)

Mobile home – Additional installation requirements:

This dryer is suitable for mobile home installations. The installation must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile home construction and Safety, Title 24, HUD Part 280) or Standard CAN/CSA-Z240 MH.

Drain System

Drain system can be installed using a oor drain, wall standpipe, oor standpipe, or laundry tub. Select method you need.

IMPORTANT: To avoid siphoning, only 4.5" (114 mm) of drain hose should be inside standpipe. Always secure drain hose with cable tie.

Floor standpipe drain system

Laundry tub drain system

4.5"

(114 mm)

max. 54"

(1372 mm)

min. 30"

(762 mm)

4.5"

(114 mm)

max. 54"

(1372 mm)

min. 30"

(762 mm)

Without pedestal

max. 69"

4.5"

(114 mm)

(1753 mm)

min. 30"

(762 mm)

With 15" matching pedestal

Minimum diameter for a standpipe drain: 2" (51 mm). Minimum carry-away capacity: 17 gal. (64 L) per minute. A 1/4" (6 mm)

diameter to 1" (25 mm) diameter Standpipe Adapter Kit is

available. Top of standpipe must be at least 30" (762 mm) high; install no higher than 54" (1.37 m) from bottom of dryer.

IMPORTANT: Only 4.5" (114 mm) of drain hose should be inside standpipe; do not force excess hose into standpipe.

Wall standpipe drain system

4.5"

(114 mm)

See requirements for oor standpipe drain system.

Minimum capacity: 20 gal. (76 L). Top of laundry tub must be

at least 30" (762 mm) above oor; install no higher than

54" (1.37 m) from bottom of dryer. IMPORTANT: Only 4.5" (114 mm) of drain hose should lay

on side of laundry tub. Do not lay the hose at the bottom of tub.

Floor drain system

Remove the U-bend at the end of the drain hose by cutting

the hose at the end of the U-bend for the oor drain system as

shown in the picture above. NOTE: Cut hose so that no more than 4.5" (114 mm) of the hose

is in the oor drain to avoid siphoning.

Electrical Requirements - U.S.A. Only

It is your responsibility:

■ To contact a qualied electrical installer.

■ To be sure that the electrical connection is adequate and

in conformance with the National Electrical Code, ANSI/

NFPA 70 – latest edition and all local codes and ordinances.

The National Electrical Code requires a 4-wire power supply

connection for homes built after 1996, dryer circuits involved

in remodeling after 1996, and all mobile home installations.

A copy of the above code standards can be obtained from:

National Fire Protection Association, One Batterymarch Park,

Quincy, MA 02269.

■ To supply the required 3 or 4 wire, single phase, 120/240

volt, 60 Hz, AC only electrical supply (or 3 or 4 wire, 120/208

volt electrical supply, if specied on the serial/rating plate)

on a separate 30-amp circuit, fused on both sides of the line.

Connect to an individual branch circuit. Do not have a fuse in

the neutral or grounding circuit.

■ Do not use an extension cord.

■ If codes permit and a separate ground wire is used, it is

recommended that a qualied electrician determine that

the ground path is adequate.

Electrical Connection

To properly install your dryer, you must determine the type of electrical connection you will be using and follow the instructions provided for it here.

■ This dryer is manufactured ready to install with a 3-wire

electrical supply connection. The neutral ground conductor is permanently connected to the neutral conductor (white wire) within the dryer. If the dryer is installed with a 4-wire electrical supply connection, the neutral ground conductor must be removed from the external ground connector (green screw), and secured under the neutral terminal (center or white wire) of the terminal block. When the neutral ground conductor is secured under the neutral terminal (center or white wire) of the terminal block, the dryer cabinet is isolated from the neutral conductor. The green ground wire of the 4-wire power cord must be secured to the dryer cabinet with the green ground screw.

■ If local codes do not permit the connection of a neutral

ground wire to the neutral wire, see “Optional 3-wire connection” section.

■ A 4-wire power supply connection must be used when the

appliance is installed in a location where grounding through the neutral conductor is prohibited. Grounding through the neutral is prohibited for (1) new branch-circuit installations after 1996, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductors.

If using a power supply cord:

Use a UL listed power supply cord kit marked for use with clothes dryers. The kit should contain:

■ A UL listed 30-amp power supply cord, rated 120/240 volt

minimum. The cord should be type SRD or SRDT and be at least 4 ft. (1.22 m) long. The wires that connect to the dryer must end in ring terminals or spade terminals with upturned ends.

■ A UL listed strain relief.

Electric Dryer Power Hookup – Canada Only

Electrical Requirements

If your outlet looks like this:

Then choose a 4-wire power supply cord with ring or spade terminals and UL listed strain relief. The 4-wire power supply cord, at least 4 ft. (1.22 m) long, must have four 10-gauge copper wires and match a 4-wire receptacle of NEMA Type 14-30R. The ground wire (ground

4-wire receptacle

(14-30R)

3-wire receptacle

(10-30R)

conductor) may be either green or bare. The

neutral conductor must be identied by a white

cover.

Then choose a 3-wire power supply cord with ring or spade terminals and UL listed strain relief. The 3-wire power supply cord, at least 4 ft. (1.22 m) long, must have three 10-gauge copper wires and match a 3-wire receptacle of NEMA Type 10-30R.

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire) and be:

■ Flexible armored cable or nonmetallic sheathed copper cable

(with ground wire), covered with exible metallic conduit. All

current-carrying wires must be insulated.

■ 10-gauge solid copper wire (do not use aluminum) at least

5 ft. (1.52 m) long.

It is your responsibility:

■ To contact a qualied electrical installer.

■ To be sure that the electrical connection is adequate

and in conformance with the Canadian Electrical Code, C22.1-latest edition and all local codes. A copy of the above codes standard may be obtained from: Canadian Standards Association, 178 Rexdale Blvd., Toronto, ON M9W 1R3 CANADA.

■ To supply the required 4 wire, single phase, 120/240 volt,

60 Hz., AC only electrical supply on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Connect to an individual branch circuit.

■ This dryer is equipped with a CSA International Certied

Power Cord intended to be plugged into a standard 14-30R wall receptacle. The cord is 5 ft. (1.52 m) in length. Be sure

wall receptacle is within reach of dryer’s nal location.

4-wire receptacle (14-30R)

■ Do not use an extension cord.

If using a replacement power supply cord, it is recommended that you use Power Supply Cord Replacement Part Number

8579325. For further information, please reference the “Assistance or Service” section of the “Use and Care Guide.”

GROUNDING INSTRUCTIONS

■

For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This dryer is equipped with a cord having an equipmentgrounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

WARNING: Improper connection of the equipment-

grounding conductor can result in a risk of electric shock. Check with a qualied electrician or service representative or personnel if you are in doubt as to whether the dryer is properly grounded. Do not modify the plug provided with the dryer: if it will not t the outlet, have a proper outlet installed by a qualied electrician.

Install Leveling Legs

1. Prepare dryer for leveling legs

To avoid damaging oor, use a large at piece of cardboard

from dryer carton; place under entire back edge of dryer. Firmly grasp dryer body (not console panel) and gently lay dryer down on cardboard.

NOTE: Residual water from factory testing may drain when dryer is laying on it’s side.

2. Screw in leveling legs

SAVE THESE INSTRUCTIONS

Using a wrench and tape measure, screw leveling legs into leg holes until bottom of foot is approximately 1/2" (13 mm) from bottom of dryer.

Now stand the dryer on its feet. Slide the dryer until it is

close to its nal location.

Electric Installation - U.S.A. Only

Before you start: disconnect power.

1. Choose electrical connection type

Power supply cord 4-wire receptacle (NEMA Type 14-30R). Go to “Power Supply Cord Connection.”

Power supply cord 3-wire receptacle (NEMA Type 10-30R). Go to “Power Supply Cord Connection.”

4-wire direct connection: Go to “Direct Wire Connection.”

3-wire direct connection: Go to “Direct Wire Connection.”

Power Supply Cord Connection

NOTE: If local codes do not permit connection of a

cabinet-ground conductor to neutral wire, go to “Optional 3-wire connection.” This connection may be used with either a power supply cord or a direct wire connection.

2. Remove terminal block cover

Remove hold-down screw and terminal block cover.

Power supply cord strain relief:

1. Attach power supply cord strain relief

C D

Remove the screws from a 3/4" (19 mm) UL listed strain relief (UL marking on strain relief). Put the tabs of the two clamp sections (C) into the hole below the terminal block opening (B) so that one tab is pointing up (A) and the other is pointing down (D), and hold in place. Tighten strain relief screws just enough to hold the two clamp sections (C) together.

2. Attach power supply cord

to strain relief

1. Prepare to connect neutral ground

wire and neutral wire

Put power supply cord through the strain relief. Be sure that the wire insulation on the power supply cord is inside the

strain relief. The strain relief should have a tight t with the

dryer cabinet and be in a horizontal position. Do not further tighten strain relief screws at this point.

If your outlet looks like this:

Power supply cord 4-wire receptacle (NEMA Type 14-30R): Go to “4-Wire Power Supply Cord Connection”.

Power supply cord 3-wire receptacle (NEMA Type 10-30R): Go to “3-Wire Power Supply Cord Connection”.

4-Wire Power Supply Cord Connection

IMPORTANT: A 4-wire connection is required for mobile homes

and where local codes do not permit the use of 3-wire connections.

Remove center terminal block screw (B). Remove neutral ground wire (E) from green external ground conductor screw (A).

2. Connect neutral ground wire and

neutral wire

Connect neutral ground wire (E) and neutral wire (white or center) (C) of power supply cord under center terminal block screw (B). Tighten screw.

3. Connect ground wire

4-wire receptacle (NEMA type 14-30R)

Spade terminals with upturned ends

4-prong plug

Ring terminals

Connect ground wire (F) (green or bare) of power supply cord under green external ground conductor screw (A). Tighten screw.

4. Connect remaining wires

2. Connect neutral wire

Connect remaining wires under outer terminal block screws. Tighten screws. Finally, reinsert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold-down screw. Now, go to “Connect Outlet Hose.”

3-Wire Power Supply Cord Connection

Use where local codes permit connecting cabinet-ground conductor to neutral wire.

3-wire receptacle (NEMA type 10-30R)

Spade terminals with upturned ends

3-prong plug

Ring terminals

Connect neutral wire (white or center) (C) of power supply cord under center terminal block screw (B). Tighten screw.

3. Connect remaining wires

1. Remove center screw

Remove center terminal block screw (B).

Direct Wire Connection

2. Attach direct wire cable to strain relief

Put direct wire cable through the strain relief. The strain

relief should have a tight t with the dryer cabinet and be in

a horizontal position. Tighten strain relief screw against the direct wire cable.

If your wiring looks like this:

4-wire direct connection: Go to “4-Wire Direct Wire Connection”.

Direct wire strain relief

1. Attach direct wire strain relief

Unscrew the removable conduit connector (A) and any screws from a 3/4" (19 mm) UL listed strain relief (UL marking on strain relief). Put the threaded section of the strain relief (C) through the hole below the terminal block opening (B). Reaching inside the terminal block opening, screw the removable conduit connector (A) onto the strain relief threads and tighten securely.

3-wire direct connection: Go to “3-Wire Direct Wire Connection”.

4-Wire Direct Wire Connection

IMPORTANT: A 4-wire connection is required for mobile homes

and where local codes do not permit 3-wire connections.

1. Prepare your 4-wire cable

for direct connection

⁄

(89 mm)

(127 mm)

Direct wire cable must have 5 ft. (1.52 m) of extra length so dryer may be moved if needed.

Strip 5" (127 mm) of outer covering from end of cable, leaving bare ground wire at 5" (127 mm). Cut 11/2" (38 mm) from remaining 3 wires. Strip insulation back 1" (25 mm). Shape ends of wires into hooks.

(25 mm)

+ 25 hidden pages