W10560165A
TOP-LOADING
LAVEUSE À CHARGEMENT
WASHER
USE AND CARE GUIDE
Para una versión de estas instrucciones en español, visite www.whirlpool.com
Table of Contents
WASHER SAFETY .............................................................2
WHAT’S NEW UNDER THE LID? .....................................3
CONTROL PANEL AND FEATURES ................................4
CYCLE GUIDE ................................................................... 5
USING YOUR WASHER ....................................................6
WASHER MAINTENANCE ................................................9
TROUBLESHOOTING .....................................................11
WARRANTY .....................................................................15
ASSISTANCE OR SERVICE ........................ BACK COVER
PAR LE DESSUS
GUIDE D’UTILISATION ET
D’ENTRETIEN
Table des matières
SÉCURITÉ DE LA LAVEUSE ..........................................16
QUOI DE NEUF SOUS LE COUVERCLE? .....................17
TABLEAU DE COMMANDE ET
CARACTÉRISTIQUES ..................................................... 18
GUIDE DE PROGRAMMES ............................................20
UTILISATION DE LA LAVEUSE ......................................21
ENTRETIEN DE LA LAVEUSE ........................................24
DÉPANNAGE ...................................................................26
GARANTIE .......................................................................31
ASSISTANCE OU SERVICE. ..... COUVERTURE ARRIÈRE
W10560165A
W10560166A-SP
WASHER SAFETY
2
WHAT’S NEW UNDER THE LID?
Your new washer will operate differently than your past agitator-style washer.
Lid Lock
To allow for higher spin speeds, the lid will lock and the
Lid Locked light will turn on. When this light is lit, the
lid is locked and cannot be opened. When this light is
blinking, the washer is paused. When this light is off,
the lid can be opened. After a cycle is started, water will
enter the washer and then the lid will lock. If you need to
open the lid to add a garment after this point, you must
press START/Pause and wait for the lid to unlock. The
lid will only unlock after washer movement has stopped.
Depending on when in the cycle you try to pause, it may
take several seconds to several minutes for the lid to
unlock. Press START/Pause to resume the cycle.
Sensing
This washer will perform a series of spins to check
for load balance. During this time, a series of clicks
and a whirring noise signal that sensing technology
is determining if there is an off-balance load.
Sounds
At different stages of the wash cycle, you may hear
sounds and pauses that are different from those of your
previous washer. For example, you may hear a clicking
and hum at the beginning of the cycle as the lid lock
goes through a self-test. There will be different kinds of
humming and whirring sounds as the agitator tests for
load balance or moves the load. And, sometimes, you
may hear nothing at all as the washer allows time for
clothes to soak.
Spray Rinse
Select cycles default to a spray rinse. During these cycles,
you will hear water enter the washer as the tub spins,
allowing the rinse water to penetrate clothes. Check the
“Cycle Guide” for details.
IMPORTANT:
• After the washer basket lls to the selected water level, the lid must be closed before the wash cycle can start.
If lling stops with the lid open, close lid and press START button.
• Fabric Softener option must be selected to ensure fabric softener dispenses at the correct time.
3
CONTROL PANEL AND FEATURES
1
2 3
4 5
1
LOAD SIZE
Select the setting most suitable for your load. Small will
add a low amount of water for smaller loads and Ex Large
will add the most amount of water for large or bulky loads.
Items need to move freely. Tightly packing can lead to poor
cleaning performance, and may increase wrinkling and
tangling.
WASH TEMP
2
Wash Temp senses and maintains uniform water
temperatures by regulating incoming hot and cold water.
Select a wash temperature based on the type of fabric
and soils being washed. For best results and following the
garment label instructions, use the warmest wash water safe
for your fabric.
• On some models and cycles, warm and hot water may be
cooler than your previous washer.
• Even in a cold and cool water wash, some warm water
may be added to the washer to maintain a minimum
temperature.
WASH CYCLE KNOB
3
Use the Wash Cycle knob to select available cycles on your
washer. See “Cycle Guide” for detailed descriptions
of cycles.
4
RINSE OPTIONS
The following options may be added to most cycles.
See “Cycle Guide” for additional details.
1 RINSE
This option is used to limit a cycle to one rinse.
2 RINSES
This option can be used to automatically add a
second rinse to most cycles.
1 RINSE with SOFTENER
This option must be selected if using fabric softener
during a cycle. It ensures that fabric softener is added
at the correct time in the rinse for even distribution.
2 RINSES with SOFTENER
This option turns on both the Softener and the 2 Rinses
option.
5
SOIL LEVEL
Select the most suitable setting for your load. For heavily
soiled and sturdy fabrics, select Heavy Soil Level for more
wash time, if needed.
7
6
START/PAUSE BUTTON
Press to start the selected cycle; press again to pause
the cycle and unlock the lid.
NOTE: If the washer is spinning, it may take several
minutes to unlock the lid. Press and hold 3 seconds
to cancel a cycle.
7
CYCLE STATUS LIGHTS INDICATOR
The Cycle Status Lights show the progress of a cycle.
At each stage of the process, you may notice sounds or
pauses that are different from traditional washers.
FILL
When the START/Pause button is pressed, the washer will
If the lid is open when the water stops entering the
NOTE: Avoid opening lid during sensing phase. The
WASH
You will hear the agitator moving the load. The motor
RINSE
6
ll to the selected water level. If the lid is closed when the
washer is done lling, the lid will lock and the washer will
begin operation.
washer, the cycle will not begin until the lid has been
closed and the START/Pause button is pressed. If the
cycle has not been started within 10 minutes of the water
lling the washer, the washer will pump out the water.
sensing process will start over when the washer is
restarted. The sensing light may also come on during the
Soak and Wash portions of the cycle. This is normal. To
restart the washer after the lid has been opened, press
START.
sounds may change at different stages in the cycle.
The wash time is determined by the selected soil level.
You will hear sounds similar to the wash cycle as the
washer rinses and moves the load. You may hear the
motor turning on briey (short hum) to move the basket
while lling. Fabric softener will be added if the 1 Rinse
with Softener or 2 Rinses with Softener option was
selected.
Some cycles use spray rinsing. After draining and
spinning out wash water, the washer will continue
to spin and spray in rinse water for the entire rinse time.
4
SPIN
LOCKED
The washer spins the load at increasing speeds for
proper water removal, based on the selected cycle
and spin speed.
DONE
Once the cycle is complete, this light will come on.
Remove the load promptly for best results.
If you need to open the lid, press
CYCLE GUIDE
For best fabric care, choose the cycle that best ts the load being washed.
Recommended settings for best performance are shown in Bold.
Not all cycles and options are available on all models.
To allow for higher spin speeds, the lid
will lock and the Locked light will turn
on. When this light is lit, the lid is locked
and cannot be opened. When this light is
blinking, the washer is paused. When this
light is off, the lid can be opened.
START/Pause. The lid will unlock once
the washer movement has stopped. This
may take several minutes if the load was
spinning at high speed. Press START/
Pause again to resume the cycle.
Items to wash: Cycle: Wash Temp*: Spin
Speed**:
Machine-wash silks,
hand-wash fabrics
Sturdy fabrics, colorfast
items, towels, jeans
Large items such as
sheets, sleeping bags,
small comforters,
jackets, small washable
rugs
Cottons, linens, and
mixed garment loads
No-iron fabrics, cottons,
perm press, linens,
synthetics
Small loads, cottons,
polyester, perm press
Bright or darkly colored
cottons, linens, casual
and mixed loads
Heavily soiled fabrics Soak Hot
Hand-washed garments
or dripping wet items
Swimsuits and items
requiring rinsing without
detergent
No clothes in washer Clean Washer
Delicate Hot
Heavy Duty Hot
Bulky Items/
Sheets
Normal Hot
Wrinkle Control Hot
Quick Wash Hot
Cold Wash Cold
Drain &
Spin
Rinse &
Spin
with affresh
®
Warm
Cool
Cold
Tap Cold
Warm
Cool
Cold
Tap Cold
Hot
Warm
Cool
Cold
Tap Cold
Warm
Cool
Cold
Tap Cold
Warm
Cool
Cold
Warm
Cool
Cold
Tap Cold
Tap Cold
Warm
Cool
Cold
Tap Cold
N/A High This cycle uses a spin to shorten drying times for heavy fabrics or
Cold rinse only High Combines a rinse and high speed spin for loads requiring an additional
Hot
Warm
Cool
Cold
Tap Cold
No Spin Use this cycle to soak small spots of set in stains on fabrics. The
*All rinses are cold.
**Spin speed is integrated into the cycle and cannot be selected.
Cycle Details:
Low Use this cycle to wash lightly soiled garments indicating “Machine
Washable Silks” or “Gentle” cycle on the care label. Place small items
in mesh garment bags before washing. This cycle uses a higher, preset
water level.
High Provides maximum wash time and action for tough stains and soils.
Use this cycle for heavily soiled or sturdy items. Water-level sensing
process may take longer for some items than for others because they
will absorb more water than other fabric types.
High Use this cycle to wash large items such as jackets and small
comforters. The washer will ll with enough water to wet down the load
before the wash portion of the cycle begins, and uses a higher water
level than other cycles.
High Use this cycle for normally soiled cottons and mixed fabric loads. This
cycle uses spray rinses.
Low Use this cycle to wash loads of no-iron fabrics such as sport shirts,
blouses, casual business clothes, permanent press, and blends.
Low Use this cycle to wash small, lightly soiled loads of 2-3 items that are
needed in a hurry. This cycle features a spray rinse.
High Cold water with an additional wash action gently lifts stains while caring
for fabrics. Settings may be adjusted as desired, but must use only cold
water settings.
washer will use intermittent agitation and soaking. After time has
expired, water will drain, but the washer will not spin. Cycle is
complete.
special-care items washed by hand. Use this cycle to drain washer
after cancelling a cycle or completing a cycle after a power failure.
rinse cycle or to complete a load after power interruption. Also use for
loads that require rinsing only.
Low Use this cycle every 30 washes to keep the inside of your washer
fresh and clean. This cycle uses a higher water level. Use with affresh®
Washer Cleaner tablet or liquid chlorine bleach to thoroughly clean
the inside of your washer. This cycle should not be interrupted. See
“Washer Care.”
IMPORTANT: Do not place garments or other items in the washer
during the Clean Washer with affresh® cycle. Use this cycle with an
empty wash tub.
5
USING YOUR WASHER
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
re, or electrical shock.
1. Sort and prepare your laundry
• Empty pockets. Loose change, buttons, or any small object
can pass under the agitator and become trapped, causing
unexpected sounds.
• Sort garments by recommended cycle, water temperature,
and colorfastness.
• Separate heavily soiled garments from lightly soiled.
• Separate delicate garments from sturdy fabrics.
• Do not dry garments if stains remain after washing, because
heat can set stains into fabric.
• Treat stains promptly.
• Close zippers, fasten hooks, tie strings and sashes, and
remove non-washable trim and ornaments.
• Mend rips and tears to avoid further damage to garments
during washing.
2. Add laundry products
Add a measured amount of detergent or single-dose laundry
packet into the basket.
If using Oxi-type boosters, color-safe bleach, or fabric
softener crystals, add to the bottom of the washer basket
before adding clothes.
NOTE: Follow the manufacturer’s instructions to determine
the amount of laundry products to use.
Helpful Tips:
• When washing water-proof or water-resistant items, load
evenly. See “Cycle Guide” for tips and more information on
using the Bulky Items cycle.
• Use mesh garment bags to help avoid tangling when
washing delicate or small items.
• Turn knits inside out to avoid pilling. Separate lint-takers
from lint-givers. Synthetics, knits, and corduroy fabrics will
pick up lint from towels, rugs, and chenille fabrics.
Always read and follow fabric care label instructions to avoid
damage to your garments.
6
3. Load laundry into washer
5. Add fabric softener, if desired
Load garments in loose heaps evenly
around basket wall. For best results, do
not pack the load tightly. Do not wrap
large items such as sheets around the
agitator; load them in loose piles around
the sides of the basket. Try mixing
different sized items to reduce tangling.
IMPORTANT: Do not tightly pack or
force items into washer. Items need to
move freely for best cleaning and to reduce wrinkling
and tangling.
4. Add liquid chlorine bleach
to dispenser, if desired
Liquid
Chlorine Bleach
Pour a measured amount of liquid fabric
softener into dispenser; always follow
manufacturer’s directions for correct amount
of fabric softener based on your load size.
Dilute liquid fabric softener by lling the
dispenser with warm water until liquid reaches the underside
of the rim. See max ll line arrows.
IMPORTANT: 1 Rinse with Softener or
2 Rinses with Softener option must be
selected to ensure proper distribution of the
fabric softener during the nal rinse portion
of the cycle.
Adding Liquid Fabric Softener Manually
to Wash Load
During the nal rinse, wait until the washer has completed lling,
press the START/Pause button to pause the washer. Lift the lid
and add the measured recommended amount of liquid fabric
softener. Do not allow liquid fabric softener to spill, splash, drip,
or run into the basket or on load. Do not use more than the
recommended amount. Close the lid and press the START/Pause
button again to start the washer.
MAX FILL
6. Select cycle
Do not overll, dilute, or use more than 1 cup (250 mL). Do
not use color-safe bleach or Oxi products in the same cycle
with liquid chlorine bleach.
Turn cycle knob to choose your wash cycle.
7
7. Select LOAD SIZE
Select the load size setting most suitable for your load. Small
will add a low amount of water for smaller loads and Ex Large
will add the most amount of water for large or bulky loads.
Items need to move freely.
9. Select rinse options, if desired
Select 1 or 2 Rinses (with or without fabric softener) by
turning the knob to the desired setting.
8. Select WASH TEMP
Once you select a cycle, select the desired wash temperature
by turning the Wash Temp knob to the desired setting.
Always read and follow fabric care label instructions to avoid
damage to your garments.
Wash Temp Suggested Fabrics
Hot
Some cold water is added to save
energy. This will be cooler than
your hot water heater setting.
Warm
Some cold water will be added, so
this will be cooler than what your
previous washer provided.
Cool
Warm water is added to assist in
soil removal and to help dissolve
detergents.
Cold
Warm water may be added to
assist in soil removal and to help
dissolve detergents.
Tap Cold
This is the temperature from your
faucet.
Whites and pastels
Durable garments
Heavy soils
Bright colors
Moderate to light soils
Colors that bleed
or fade
Light soils
Dark colors that
bleed or fade
Light soils
Dark colors that
bleed or fade
Light soils
10. Select SOIL LEVEL
Once you select a cycle, select the desired soil level by turning
the Soil Level knob to the desired setting.
11. Press START/Pause
to begin wash cycle
Press the START/Pause button to start the wash cycle. When
the cycle has nished, the DONE indicator will light. Promptly
remove garments after cycle has completed to avoid odor,
reduce wrinkling, and rusting of metal hooks, zippers, and
snaps.
Unlocking the lid to add garments
If you need to open the lid to add 1 or 2 missed garments:
Press START/Pause; the lid will unlock once the washer
movement has stopped. This may take several minutes if the
load was spinning at high speed. Then close lid and press
START/Pause again to restart the cycle.
If lid is left open for more than 10 minutes the water will pump
out automatically.
8
WASHER MAINTENANCE
WATER INLET HOSES
Replace inlet hoses after 5 years of use to reduce the risk of
hose failure. Periodically inspect and replace inlet hoses if
bulges, kinks, cuts, wear, or leaks are found.
When replacing your inlet hoses, mark the date of replacement
on the label with a permanent marker.
NOTE: This washer does not include inlet hoses. See the
“Installation Instructions” for more information.
WASHER CARE
Recommendations to Help Keep Your Washer Clean and
Performing at its Best
1. Always follow the detergent manufacturer’s instructions
regarding the amount of detergent to use. Never use more
than the recommended amount because that may increase
the rate at which detergent and soil residue accumulate
inside your washer, which in turn may result in undesirable
odor.
2. Use warm and hot wash water settings sometimes (not
exclusively cold water washes), because they do a better
job of controlling the rate at which soils and detergent
accumulate.
3. Always leave the washer lid open between uses to help dry
out the washer and prevent the buildup of odor-causing
residue.
Cleaning Your Top Loading Washer
Read these instructions completely before beginning the
routine cleaning processes recommended below. This Washer
Maintenance Procedure should be performed, at a minimum,
once per month or every 30 wash cycles, whichever occurs
sooner, to control the rate at which soils and detergent may
otherwise accumulate in your washer.
Cleaning the Inside of the Washer
To keep your washer odor-free, follow the usage instructions
provided above, and use this recommended monthly cleaning
procedure:
Recommended Cycle for Cleaning the Washer
Refer to the “Cycle Guide” for the optimal cycle for cleaning
the inside of the washer. Use this cycle with affresh® Washer
Cleaner or liquid chlorine bleach as described below.
Begin procedure
1. affesh® Washer Cleaner Cycle Procedure
(Recommended for Best Performance):
a. Open the washer lid and remove any clothing or items.
b. Place an affesh® Washer Cleaner tablet in the bottom
of the washer basket.
c. Do not place an affresh® Washer Cleaner tablet in the
detergent dispenser.
d. Do not add any detergent or other chemical to the
washer when following this procedure.
e. Close the washer lid.
f. Select the cycle recommended for cleaning the inside
of the washer.
g. Press the START/Pause/Unlock button to start the cycle.
NOTE: For best results, do not interrupt cycle. If cycle must
be interrupted, press START/Pause/Unlock once or twice
(depending on model). After the cycle has stopped, run a
RINSE & SPIN cycle to rinse cleaner from washer.
WASHER CARE (cont.)
2. Chlorine Bleach Procedure (Alternative):
a. Open the washer lid and remove any clothing or items.
b. Add 1 cup (236 mL) of liquid chlorine bleach to the
bleach compartment.
NOTE: Use of more liquid chlorine bleach than is
recommended above could cause washer damage over
time.
c. Close the washer lid.
d. Do not add any detergent or other chemical to the
washer when following this procedure.
e. Select the cycle recommended for cleaning the inside
of the washer.
f. Press the START/Pause/Unlock button to start the cycle.
NOTE: For best results, do not interrupt cycle. If cycle must
be interrupted, press START/Pause/Unlock once or twice
(depending on model). After the cycle has stopped, run a
RINSE & SPIN cycle to rinse cleaner from washer.
Cleaning the Dispensers
After a period of using your washer, you may nd some residue
buildup in the washer’s dispensers. To remove residue from
the dispensers, wipe them with a damp cloth and towel dry.
Do not attempt to remove the dispensers or trim for cleaning.
The dispensers and trim are not removable. If your model has
a dispenser drawer, however, remove the drawer and clean
it before or after you run the Clean Washer cycle. Use an allpurpose surface cleaner, if needed.
Cleaning the Outside of the Washer
Use a soft, damp cloth or sponge to wipe away any spills.
Use only mild soaps or cleaners when cleaning external
washer surfaces.
IMPORTANT: To avoid damaging the washer’s nish, do not
use abrasive products.
9
NON-USE AND VACATION CARE
REINSTALLING/USING WASHER AGAIN
Operate your washer only when you are home. If moving,
or not using your washer for a period of time, follow these
steps:
1. Unplug or disconnect power to washer.
2. Turn off water supply to washer, to avoid ooding due
to water pressure surge.
WINTER STORAGE CARE
IMPORTANT: To avoid damage, install and store washer
where it will not freeze. Because some water may stay in
hoses, freezing can damage washer. If storing or moving
during freezing weather, winterize your washer.
To winterize washer:
1. Shut off both water faucets; disconnect and drain water
inlet hoses.
2. Put 1 qt. (1 L) of R.V.-type antifreeze in basket and run
washer on RINSE & SPIN cycle for about 30 seconds
to mix antifreeze and remaining water.
3. Unplug washer or disconnect power.
TRANSPORTING YOUR WASHER
1. Shut off both water faucets. Disconnect and drain water
inlet hoses.
2. If washer will be moved during freezing weather, follow
WINTER STORAGE CARE directions before moving.
3. Disconnect drain hose from drain system and drain any
remaining water into a pan or bucket. Disconnect drain
hose from back of washer.
4. Unplug power cord.
5. Place inlet hoses and drain hose inside washer basket.
6. Drape power cord over edge and into washer basket.
7. Place packing tray from original shipping materials
back inside washer. If you do not have packing tray,
place heavy blankets or towels into basket opening.
Close lid and place tape over lid and down front of
washer. Keep lid taped until washer is placed in new
location.
To reinstall washer after non-use, vacation, winter storage,
or moving:
1. Refer to Installation Instructions to locate, level, and
connect washer.
2. Before using again, run washer through the following
recommended procedure:
To use washer again:
1. Flush water pipes and hoses. Reconnect water inlet
hoses. Turn on both water faucets.
WARNING
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
re, or electrical shock.
2. Plug in washer or reconnect power.
3. Run washer through BULKY ITEMS/SHEETS cycle to
clean washer and remove antifreeze, if used. Use 1/2 the
manufacturer’s recommended amount of detergent for a
medium-size load.
10
Loading...