Weider CROSSBAR 2000X User Manual

Model No. WESY77730

Visit our website at

www.TheCrossBow.com

Serial No.

Write the serial number in the

pace above for future reference.

s

Serial Number Decal (under seat)

QUESTIONS?

As a manufacturer, we are com­mitted to providing complete
customer satisfaction. If you
have questions, or if there are
missing or damaged parts, we
will guarantee complete satis­faction through direct assis­tance from our factory.

TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL­FREE CUSTOMER HOT LINE.
The trained technicians on our
customer hot line will provide
immediate assistance, free of
charge.

CUSTOMER HOT LINE:

1-800-999-3756

Mon.–Fri., 6 a.m.–6 p.m. MST

USERʼS MANUAL

CAUTION

Read all precautions and instruc­tions in this manual before
using this equipment. Save this
manual for future reference.

TABLE OF CONTENTS

Keep hands and
fingers clear of
this area.

WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

EFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

B

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

CABLE DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING are attached in the center of
this manual. Remove the PART IDENTIFICATION CHART and PART LIST/EXPLODED DRAWING before begin­ning assembly.

WARNING DECAL PLACEMENT

The decals shown here have been
placed on the resistance system. If a
decal is missing or illegible, please call
our Customer Service Department toll­free at 1-800-999-3756, Monday through
Friday, 6 a.m. until 6 p.m. Mountain Time,
and order a free replacement decal.
Apply the decal in the location shown.

CrossBow by WEIDER is a trademark of ICON Health & Fitness, Inc.

2

IMPORTANT PRECAUTIONS

WARNING: To reduce the risk of serious injury, read the following important precautions

before using the resistance system.

1. Read all instructions in this manual before
using the resistance system. Use the resist­ance system only as described in this manual.

2. It is the responsibility of the owner to ensure
that all users of the resistance system are
adequately informed of all precautions.

3. The resistance system is intended for home
use only. Do not use the resistance system in
any commercial, rental, or institutional setting.

4. Use the resistance system only on a level
surface. Cover the floor beneath the resist­ance system to protect the floor.

5. Make sure that all parts are properly tight­ened each time the resistance system is
used. Replace any worn parts immediately.

6. Keep children under 12 and pets away from
the resistance system at all times.

7. Keep hands and feet away from moving parts.

8. Always wear athletic shoes for foot protec­tion while exercising.

9. The top frame is not designed to be used for
pull-up exercises. Do not hang on the top
frame.

10. The resistance system is designed to sup­port a maximum user weight of 300 pounds.

11. Pull on the low pulley cable only while sitting
on the bench or standing on the base plate.
Pull on the high pulley cables only while sit­ting on the bench, with the seat in one of the
three positions closest to the upright base,
or while standing on the base plate.

12. The resistance system is designed to be
used with the included resistance, and the
resistance included with a CrossBow by WEI-

™

Power Pak. Do not use the resistance

DER
system with any other type of resistance.

13. When adding resistance, both ends of the
crossbows must rest under the two “U”­channels. Add and remove crossbows from
the “U”-channels one crossbow at a time.

14. Keep clear of the area around the “U”-chan­nels while the resistance system is in use.
Do not add or remove crossbows from the
“U”-channels while the end of the long cable
is pulled out.

15. Always adjust the crossbow assembly to the
horizontal position and make sure the ful­crum knob is secure before using the resist­ance system.

16. Make sure the rings on the crossbows are
pushed against the crossbow spacer before
using the resistance system.

17. If you purchase the optional lat bar, always
disconnect it from the short cables when per­forming an exercise that does not require it.

18. Make sure the storage knob is in place and
fully tightened each time the resistance sys­tem is used.

19. Make sure that the cables remain on the pul­leys at all times. If the cables bind as you are
exercising, stop immediately and make sure
that the cables are on the pulleys.

20. If you feel pain or dizziness while exercising,
stop immediately and begin cooling down.

WARNING: Before beginning this or any exercise program, consult your physician. This

is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.

3

BEFORE YOU BEGIN

Thank you for selecting the innovative CrossBow by
WEIDER™2000X resistance system. The resistance
system offers a selection of stations designed to devel­op every major muscle group of the body. Whether your
goal is to tone your body, build dramatic muscle size
and strength, or improve your cardiovascular system,
the resistance system will help you to achieve the spe­cific results you want.

For your benefit, read this manual carefully before
using the resistance system. If you have questions

ASSEMBLED
DIMENSIONS:
Height: 82 in.
Width: 64 in.
Depth: 80 in.

Fulcrum Knob

Curl Bar

after reading this manual, please call our Customer
Service Department toll-free at 1-800-999-3756,
Monday through Friday, 6 a.m. until 6 p.m. Mountain
Time (excluding holidays). To help us assist you, please
note the product model number and serial number
before calling. The model number is WESY77730. The
serial number can be found on a decal attached to the
resistance system (see the front cover of this manual).

Before reading further, please review the drawing below
and familiarize yourself with the parts that are labeled.

Top Frame

Lat Tower

High Pulley

Crossbows

Upright

Storage Knob

Backrest

Seat

Leg Lever

Floor Mat

“U”-Channel

Foot Plate

Low Pulley

Base Plate

Seat Knob

4

ASSEMBLY

Make Things Easier for Yourself

This manual is designed to ensure that the resist­ance system can be assembled successfully by
most people. However, it is important to realize
that the versatile resistance system has many
parts and that the assembly process will take
time. Most people find that by setting aside plenty
of time, assembly will go smoothly.

Before beginning assembly, carefully read the
following information and instructions:

Tighten all parts as you assemble them, unless

•

instructed to do otherwise.

As you assemble the resistance system, make

•

sure all parts are oriented as shown in the draw­ings.

The included Allen wrenches and the follow­ing tools (not included) are required for assem­bly:

• Two adjustable wrenches

• One rubber mallet

• Assembly requires two persons.

• Place all parts in a cleared area and remove the

packing materials. Do not dispose of the packing
materials until assembly is completed.

• For help identifying small parts, use the PART
IDENTIFICATION CHART. Note: Some small

parts may have been pre-attached for shipping. If
a part is not in the parts bag, check to see if it
has been pre-attached.

1.

Before beginning assembly, make sure that
you have read and understand the informa­tion in the box above.

Attach two Plastic Feet (53) and two Large Plastic
Feet (102) to the Base (1) with four M4 x 16mm
Screws (62).

Attach the Upright (3) to the Base (1) with two
M10 x 66mm Carriage Bolts (83), two M10 x
72mm Bolts (64), and four M10 Nylon Locknuts
(76) as shown. Note: This step will be easier if

the Upright and the Base are tipped on their
sides.

• One standard screwdriver

• One Phillips screwdriver

• Lubricant, such as grease or petroleum jelly,
and soapy water.

Assembly will be more convenient if you have a
socket set, a set of open-end or closed-end
wrenches, or a set of ratchet wrenches.

1

3

64

76

76

76

1

102

62

102

53

62

53

83

62

5

2. Attach a Wheel (31) to the outside of the Base (1)
with an M10 x 108mm Bolt (81), three M10
Washers (75), and an M10 Nylon Locknut (76).

o not overtighten the Locknut; the Wheel

D
must be able to turn easily.

Attach the other Wheel (not shown) in the
same manner.

2

76

75

75

81

31

1

3. Orient the Cross Tube (11) as shown, with the
welded tubes at the bottom. Attach the Foot Plate
(23) and the Cross Tube to the Upright (3) with
two M10 x 140mm Carriage Bolts (73), two M10
Washers (75), and two M10 Nuts (47). Do not

insert a bolt into the upper hole in the Foot
Plate yet.

4. Press the Front Leg Foot (27) onto the bottom of
the Front Leg (6). Note that the front of the

Front Leg Foot is taller than the back.

Attach the Bench Rail (5), with the hook on the
bottom, to the Front Leg (6) with two M10 x
53mm Carriage Bolts (61) and two M10 Nylon
Locknuts (76).

3

73

4

61

Front

23

3

76

76

6

75

11

5

47

Welded

Tube

Hook

5. Lubricate an M10 x 103mm Bolt (66) with grease.
Attach the Bench Rail (5) to the Upright (3) with
the Bolt and an M10 Nylon Locknut (76). Do not

overtighten the Locknut; the Bench Rail must
be able to pivot easily.

Tighten the Storage Knob (30) into the Upright (3)
and the Bench Rail (5).

27

5

Insert the bolt

through this hole

5

76

30

3

66

Lubricate

6

6. Attach the Lat Tower (4) to the Upright (3) with
four M10 x 25mm Button Head Screws (87) and
four M10 Lock Washers (103).

6

Attach the Name Plate (89) to the Lat Tower (4)

ith two M4 x 16mm Screws (62).

w

7. Attach two Eyebolts (34) to the Top Frame (10)
with two M8 Washers (59) and two M8 Nylon
Locknuts (65). Do not overtighten the Locknuts;
the Eyebolts must be able to rotate freely.

Attach the Top Frame (10) to the Lat Tower (4)
with two M10 x 65mm Button Head Screws (70),
two M10 Washers (75), and the Top Frame Cover
(93). Make sure that the Eyebolts (34) are ori-

ented as shown in the inset drawing. If they
are not, turn the Top Frame around and reat­tach it.

4

103

87

62

89

62

103

3

7

70

65

59

34

75

93

10

87

65

59

8. Attach the Leg Lever Bumper (55) to the Front
Leg (6) with an M4 x 19mm Screw (77).

Lubricate an M10 x 68mm Bolt (56) with grease.
Orient the Leg Lever (7) with the slot on the side
shown. Attach the Leg Lever to the Front Leg (6)
with the Bolt and an M10 Nylon Locknut (76). Do

not overtighten the Nylon Locknut; the Leg
Lever must be able to pivot easily.

Side View

10

34

8

34

4

Lubricate

56

6

7

Slot

55

77

76

4

7

9. Attach two 8mm Metal Spacers (97), a 60mm
Metal Spacer (39), and two Bearing Wheels (46)
to one end of the Seat Carriage (12) with an M8 x

04mm Button Head Bolt (60) and an M8 Nylon

1
Locknut (65) as shown. Make sure that the parts

re oriented as shown in the inset drawing; the

a
Seat Knob (not shown) will not engage the
Bench Rail (not shown) if they are incorrectly
oriented. Do not overtighten the Locknut; the
Bearing Wheels must be able to roll easily.

Attach two Bearing Wheels (not shown) to the
other end of the Seat Carriage (12) in the
same manner.

9

60

65

7

9

46

39

97

46

97

Wide

Side

2

1

Attach second

set of wheels

46

here

39

46

97

10. Attach the Seat Knob (45) to the Seat Carriage
(12) with two M6 x 13mm Bolts (92) and two M6
Nylon Locknuts (69). Make sure that the slot in

the Knob is aligned with the slot in the Seat
Carriage, as shown.

Orient the Seat (13), the Seat Backing (9), and
the Seat Carriage (12) as shown. Attach the Seat
and the Seat Backing to the Seat Carriage with
four 1/4” x 16mm Button Head Screws (82).

11. Pull out the Seat Knob (45) as far as it will go, and
set the Seat Carriage (12) on the Bench Rail (5).

Loosely attach two 8mm Metal Spacers (97), a
60mm Metal Spacer (39), and two Bearing
Wheels (46) to the center holes in the Seat
Carriage (12) with two M8 Flange Nuts (19) and
the M8 x 114mm Axle (57). Make sure that the

serrated edge of the Flange Nuts are against
the Seat Carriage.

10

11

57

19

12

9

12

13

82

45

13

69

19

82

Slots

92

45

92

5

While a second person presses down on the Seat
(13), hold the wheel assembly firmly against the
bottom of the Bench Rail (5) and properly tighten
the M8 Flange Nuts (19). Make sure that three

threads are extending past the Nut, and that
the wide sides of all six Wheels (46) are
pressed against the Bench Rail.

Engage the Seat Knob (45) into an adjustment
hole in the Bench Rail (5).

39

97

46

97

Adjustment Hole

97

Wide

Side

46

39

46

97

8