Weed Eater BC2500 LE, 530086828 User Manual

Trademark
R
Please do not return unit to retailer. Por favor, no devuelva el aparato al lugar de compra. Veuillez ne pas retourner l’outil au détaillant.
1-800-554-6723
www.weedeater.com
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
BC2500 LE
ENGLISH ESPAÑOL
For Occasional Use Only
WARNING:
Read and follow all Safety Rules and Operating Instructions before using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e instrucciones de seguridad. El no hacerlo puede resultar en le­siones graves.
A VERTISSEMENT:
Lire le manuel d’instructions et bien respecter tous les avertisse­ments et toutes les instructions de sécurité. Tout défaut de le faire pourrait entraîner des blessures graves.
Electrolux Home Products, Inc. 250 Bobby Jones Expressway Augusta, GA 30907
CopyrightE2002 Electrolux Home Products, Inc.
530086828
FRANÇAIS
4/25/02
SAFETY RULES
WARNING:
appliances, basic safety precautions must al­ways be followed to reduce the risk of fire and serious injury.
DANGER:
dangerous!
including amputation or blindness to the op­erator and others. The warnings and safety instructions in this manual must be followed to provide reasonable safety and efficiency in using the unit. The operator is responsible for following the warnings and instructions in this manual and on the unit. Read the entire in­struction manual before assembling and us­ing the unit! Restrict the use of this unit to per­sons who read, understand, and follow the warnings and instructions in this manual and on the unit. Never allow children to operate this unit.
INSTRUCTION MANUAL
This unit can cause serious injury
DANGER:
away from material it does not cut. Blade thrust can cause amputation of arms or legs. Keep people and animals 50 feet (15 meters) away.
When using gardening
This power tool can be
SAFETY INFORMATION ON THE UNIT
Blade can thrust violently
Hazard Zone
50 Feet
(15 Meters)
WARNING:
as a fastening device for the blade.
WARNING:
spin after the throttle is released or, engine is turned off. The coasting blade can throw objects or seriously cut if accidentally touched. Stop the blade by contacting the right hand side of the coasting blade with material already cut.
Do not use trimmer head
The blade continues to
Stop coasting blade by contact with cut material.
WARNING:
objects violently. You and others can be blinded or injured. Wear safety glasses and leg protection.
ALWAYS WEAR:
Eye
Protection
Leg Guards
Boots
WARNING:
objects. Blade/trimmer line can throw objects violently. Others can be blinded or injured. Keep people and animals 50 feet (15 meters) away.
Trimmer line can throw
Thrown Objects
Hazard zone for thrown
OPERATOR SAFETY
Dress properly. Always wear safety
S
glasses or similar eye protection when op­erating, or performing maintenance on your unit. (Safety glasses are available.) Eye protection should be marked Z87. Always wear face or dust mask if operation
S
is dusty. Always wear heavy, long pants, long sleeves,
S
boots, and gloves. Wearing safety leg guards is recommended. Always wear foot protection. Do not go
S
barefoot or wear sandals. Secure hair above shoulder length. Secure
S
or r e m o v e loose clothing and jewelry or cloth­ing with loosely hanging ties, straps, tassels, etc. They can be caught in moving parts. Being fully covered also helps protect you
S
from debris and pieces of toxic plants thrown by spinning line/blade. Stay alert. Do not operate unit when you are
S
tired, ill, upset or under influence of alcohol, drugs, or medication. Watch what you are do­ing; use common sense. Wear hearing protection.
S
Never start or run the engine inside a
S
closed room or building. Breathing exhaust fumes can kill.
2
Keep handles free of oil and fuel.
S
Always use the handlebar and a properly
S
adjusted shoulder strap with a blade (see ASSEMBLY).
UNIT/MAINTENANCE SAFETY
WARNING:
the spark plug before performing mainte­nance (except carburetor adjustments).
Look for and replace damaged or loose
S
parts before each use. Look for and repair fuel leaks before use. Keep unit in good working condition. Throw away blades that are bent, warped,
S
cracked, broken, or damaged in any other way. Replace trimmer head parts that are cracked, chipped, broken, or damaged in any other way before using the unit. Maintain unit according to recommended
S
procedures. Keep blade sharp. Keep cut­ting line at the proper length. Use only 0.080!(2 mm) diameter Weed
S
Eater"brand replacement line. Never use wire, rope, string, etc. Install required shield properly before using
S
the unit. Use the metal shield for all metal blade use. Use the plastic shield for all line trimmer use. Use only specified blade or trimmer head;
S
make sure it is properly installed and se­curely fastened. Never start engine with clutch shroud re-
S
moved. The clutch can fly off and cause se­rious injury. Be sure blade or trimmer head stops turning
S
when engine idles. Make carburetor adjustments with the low-
S
er end supported to prevent blade or trim­mer line from contacting any object. Hold unit by hand; do not use the shoulder strap for support. Keep others away when making carburetor
S
adjustments. Use only recommended Weed Eaterrac-
S
cessories and replacement parts. Have all maintenance and service not ex-
S
plained in this manual performed by your authorized service dealer.
Stop unit and disconnect
FUEL SAFETY
Mix and pour fuel outdoors.
S
Keep away from sparks or flames.
S
Use a container approved for fuel.
S
Do not smoke or allow smoking near fuel or
S
the unit or while using the unit. Avoid spilling fuel or oil. Wipe up all fuel
S
spills before starting engine. Move at least 10 feet (3 meters) away from
S
the fueling site before starting engine. Stop engine and allow it to cool before re-
S
moving fuel cap. Empty the fuel tank before storing or trans-
S
porting the unit. Use up fuel left in the car­buretor by starting the engine and letting it run until it stops. Store unit and fuel in area where fuel vapors
S
cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc.
Always store gasoline in a container ap-
S
proved for flammable liquids.
CUTTING SAFETY
WARNING:
cut before each use. Remove objects (rocks, broken glass, nails, wire, string, etc.) which can be thrown or become entangled in the blade or trimmer head.
Keep others including children, animals,
S
bystanders, and helpers at least 50 feet (15 meters) away. Stop engine immediately if you are approached. Always keep engine on the right--hand side
S
of your body. Hold the unit firmly with both hands.
S
Keep firm footing and balance. Do not
S
overreach. Keep blade or trimmerhead below w aist level.
S
Do not raise engine above your waist. Keep all parts of your body away from
S
blade, trimmer head, and muffler when en­gine is running. Keep all of your body away from the muffler when it is hot. A hot muffler can cause serious burns. Cut from your left to your right. Cutting on
S
right side of the shield will throw debris away from the operator. Use only in daylight or good artificial light.
S
Use only for jobs explained in this manual.
S
Inspect the area to be
TRANSPORTING AND STORAGE
Stop the unit before carrying.
S
Keep muffer away from your body.
S
Allow the engine to cool and secure the unit
S
before storing or transporting it in a vehicle. Empty the fuel tank before storing or trans-
S
porting the unit. Use up fuel left in the carbu­retor by starting the engine and letting it run until it stops. Store unit so the blade or line limiter blade
S
cannot accidentally cause injury. The unit can be hung by the tube. Store unit out of reach of children.
S
SAFETY NOTICE:
through prolonged use of gasoline powered hand tools could cause blood vessel or nerve damage in the fingers, hands, and joints of people prone to circulation disorders or ab­normal swellings. Prolonged use in cold weather has been linked to blood vessel dam­age in otherwise healthy people. If symptoms occur such as numbness, pain, loss of strength, change in skin color or texture, or loss of feeling in the fingers, hands, or joints, discontinue the use of this tool and seek med­ical attention. An anti --vibration system does not guarantee the avoidance of these prob­lems. Users who operate power tools on a continual and regular basis must monitor closely their physical condition and the condi­tion of this tool.
SPECIAL NOTICE:
with a temperature limiting muffler and spark arresting screen which meets the require­ments of California Codes 4442 and 4443. All U.S. forest land and the states of California, Idaho, Maine, Minnesota, New Jersey, Ore­gon, and Washington require by law that many internal combustion engines be
Exposure to vibrations
This unit is equipped
3
equipped with a spark arresting screen. If you operate in alocale where such regulations ex­ist, you are legally responsible for maintaining the operating condition of these parts. Failure to do so is a violation of the law. For normal homeowner use, the muffler and spark arrest­ing screen will not require any service.
ASSEMBLY
CARTON CONTENTS
Check carton contents against the following list:
Brushcutter
S
Handlebar screws (2)
S
Blade shield screws (4)
S
Cupped washer
S
Large nut for installing blade
S
Long hex wrench
S
Short hex wrench
S
Bracket cover
S
Metal shield
S
Plastic shield
S
Shoulder strap with warning
S
4--point weed blade
S
Trimmer head (assembled on unit)
S
Handlebar
S
Wing nut (screwed onto shield)
S
Container of oil
S
WARNING:
connect spark plug before performing any as­sembly procedures.
WARNING:
repeat all steps to ensure your unit is properly assembled and all fasteners are secure.
Examine parts for damage. Do not use dam­aged parts.
NOTE:
missing or damaged, call 1-800-554-6723. It is normal for the fuel filter to rattle in the
empty fuel tank. Finding fuel or oil residue on muffler is normal due to carburetor adjustments and testing done by the manufacturer.
TOOLS REQUIRED
S S S
ATTACHING THE HANDLEBAR
barrier portion of the handlebar must be installed as shown to provide a barrier be­tween operator and the spinning blade.
1. Locate the decal on the handlebar. This
2. Position the bracket cover over the han-
3. Insert screws and hand tighten only. Be
If you need assistance or find parts
2 Hex wrenches (provided) Adjustable wrench or large pliers Phillips screwdriver
WARNING:
decal includes two arrows. Position the handlebar with the mounting bracket be­tween these arrows.
dlebar. Again make sure the handlebar is between the arrows.
sure the handlebar is installed correctly; then, tighten each screw securely with the short hex wrench.
Always stop unit and dis-
If received assembled,
During blade usage, the
After 50 hours of use, we recommend that your muffler be serviced or replaced by your authorized service dealer.
WARNING:
uct contains chemicals known to the State of California to cause cancer.
Handlebar
Mounting Bracket
The muffler on this prod-
Screw
Bracket Cover
ASSEMBLY OF SHOULDER STRAP
WARNING:
and handlebar adjustments are required before starting the engine.
1. Try on shoulder strap and adjust for fit and balance before starting the engine orbegin­ning a cutting operation.
2. Insert your right arm and head through the shoulder strap and allow it to rest on your left shoulder. Make sure the danger sign is on your back and the hook is to the right side of your waist.
A one-half twist is built in the shoulder
NOTE:
strap to allow the strap to rest flat on the shoul­der.
3. Adjust the strap, allowing the hook to be about 6 inches below the waist.
4. Fasten the strap hook to the clamp located between the trigger handle and the handle­bar clamp base and lift the tool to the oper­ating position.
Proper shoulder strap
CONFIGURING YOUR UNIT
You can configure your unit using a cutting head for grass and light weeds, or a weed blade for cutting grass, weeds, and brush up to 1/2 inch in diameter. To assemble your unit, go to the section for the desired configuration and follow the instructions.
ASSEMBLY INFORMATION -­TRIMMER HEAD
TRIMMER HEAD
4
NOTE:
before attaching the plastic shield and trim­mer head. To remove blade, push in locking lever and hold. Rotate blade nut until the lock­ing lever falls into one of the grooves in the dust cup. Continue to hold the locking lever. This will keep the shaft from turning while loosening the blade nut. Remove blade nut by turning clockwise. Release locking lever. Remove both washers and blade. To remove metal shield, loosen and remove the four mounting screws. See ATTACHING THE METAL SHIELD and INSTALLATION OF THE METALBLADE for illustrations. Be sure to store all parts and instructions for future use.
Remove the blade and metal shield
ATTACHING THE PLASTIC SHIELD AND TRIMMER HEAD
8. Thread trimmer head onto the shaft in the direction shown on the decal. Tighten un­til secure.
9. Release locking lever.
ASSEMBLY INFORMATION -- WEED BLADE
WEED BLADE
WARNING:
erly installed. The shield provides partial protection to the operator and others from the risk of thrown objects, and is equipped with a line limiter blade which cuts excess line to the proper length. The line limiter blade (on un­derside of shield) is sharp and can cut you.
1. Remove wing nut from shield.
2. Insert bracket into slot on shield.
3. Pivot shield until bolt passes through hole in bracket.
4. Tighten the wing nut securely.
NOTE:
threads on the threaded shaft, remove the cov­ering to expose the threads. Before installing the trimmer head, make sure the dust cup is positioned on the gearbox as shown below .
NOTE:
installed as shown in the illustration before installing the trimmer head.
5. Push in locking lever and hold.
6. Rotate dust cup until the locking lever
If your unit has a plastic cover overthe
Bracket
Slot
Shield
Make sure all parts are properly
falls into one of the grooves
The shield must be prop-
Wing Nut
Gearbox
Dust Cup
.
Locking Lever
NOTE:
tic shield before attaching the metal shield and installing one of the weed blades. To re­move the trimmer head, push in locking lever and hold. Rotate trimmer head until the lock­ing lever falls into one of the grooves in the dust cup. Continue to hold in locking lever. This will keep the shaft from turning while loosening the cutting head. To remove the plastic shield, loosen and remove wing nut. Pivot shield to release bracket from slot. See INSTALLATION OF THE CUTTING HEAD and ATTACHING THE PLASTIC SHIELD for illustrations. Be sure to store all parts and in­structions for future use. Never use the trim­mer head with the metal blade installed.
Remove the trimmer head and plas-
ATTACHING THE METAL SHIELD
WARNING:
be properly installed on the tool anytime the tool is used with a blade. The forward tip of the metal shield helps to reduce the occurrence of blade thrust which can cause serious injury such as amputation to the operator or by­standers. Failure to install the shield in the position shown can result in serious injury to the operator. The length of the shield must be aligned with the length of the tube.
1. Place the metal shield under the gearbox, and align the screw holes.
Shield
The metal shield must
Gearbox
7. Continue to hold in locking lever. This will keep the shaft from turning while tighten­ing the trimmer head.
2. Insert and thread the 4 mounting screws through the holes of the gearbox and the metal shield. Tighten evenly and secure­ly with the hex wrench provided.
5
INSTALLATION OF THE METAL BLADE
Gearbox
WARNING:
when handling or performing maintenance on the blade to avoid injury. The blade is sharpand can cut you even when it is not moving.
WARNING:
fastening hardware other than the washers and nuts shown in the following illustrations . These parts must be provided by Poulan/Weed Eater and installed as shown below. Failure to use proper parts can cause the blade to fly off and seriously hurt you or others.
NOTE:
located on the gearbox shaft and not in the parts bag. All other fasteners mentioned in the follow­ing assembly steps are in the parts bag.
1. Remove the retaining washer from the
2. Install the blade and the retaining washer
3. Make sure the raised part of the retaining
4. Slide the blade and retaining washer onto
5. Place the cupped washer onto the shaft.
6. Install the blade nut by threading onto the
The dust cup and retaining washer are
threaded shaft of the gearbox. Leave the dust cup on the shaft.
over the threaded shaft.
washer is facing the gearbox and the raised area fits into the hole in the center of the blade.
the shaft of the gearbox.
Make sure the cupped side of the washer is toward the blade.
shaft counterclockwise.
Wear protective gloves
Do not use any blades, or
Shield
Dust Cup
Retaining Washer
Cupped Washer
NOTE:
lustrated, and the blade is sandwiched between the dust cup and the retaining washer. There should be no space between the blade and the dust cup or the retaining washer.
7. Push in locking lever and hold.
8. Rotate blade nut until the locking lever
9. Continue to hold in locking lever. This will
10. Tighten blade nut firmly with a wrench.
11. Release locking lever.
12. Turn blade by hand. If the blade binds
Make sure all parts are in place as il-
falls into one of the grooves in the dust cup.
keep the shaft from turning while tightening the blade nut.
against the shield, or appearsto be uneven, the blade is not centered, and you must re­install.
Threaded Shaft
Blade
Nut
Locking Lever
6
OPERATION
KNOW YOUR BRUSHWACKER
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT .
Compare the illustrations with your unit to familiariz e yourself with the location of the various controls
and adjustments. Save this manual for future reference.
Trigger Handle
Handlebar
Trimmer head
Shield
ON/OFF
Switch
ON/OFF SWITCH
The ON/OFF switch is used to stop the engine. To stop the engine, move the ON/OFF switch to the OFF position.
PRIMER BULB
The PRIMER BULB removes air from the car­buretor and fuel lines and fills them with fuel. This allows you to start the engine with fewer pulls on the starter rope. Activate the primer bulb by pressing it and allowing it to return to its original form.
BEFORE STARTING ENGINE
WARNING:
information in the safety rules before you be­gin. If you do not understand the safety rules, do not attempt to fuel your unit. Call 1-800-554-6723.
Be sure to read the fuel
FUELING ENGINE
WARNING:
when refueling. This engine is certified to operate on un-
leaded gasoline. Before operation, gasoline must be mixed with a good quality synthetic 2-cycle air-cooled engine oil. We recommend
Poulan/Weed Eater brand synthetic oil. Mix
gasoline and oil at a ratio of 40:1 . A 40:1 ratio is obtained by mixing 3.2 ounces of oil with 1 gallon of unleaded gasoline.
DO NOT USE automotive oil or boat oil. These oils will cause engine damage. When mixing fuel, follow instructions printed on con­tainer. Once oil is added to gasoline, shake container momentarily to assure that the fuel is thoroughly mixed. Always read and follow the safety rules relating to fuel before fueling your unit.
Remove fuel cap slowly
Starter Handle
Choke Lever
Muffler
Primer Bulb
CHOKE
The CHOKE helps to supply fuel to the engine to aid in cold starting. Activate the choke by moving the choke lever to the FULL CHOKE position. After the engine attempts to start, move the choke lever to the HALF CHOKE position. Once engine has started, move the choke lever to the OFF CHOKE position.
IMPORTANT
Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during stor­age. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, empty the fuel sys­tem before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. Never use engine or carburetor cleaner prod­ucts in the fuel tank or permanent damage may occur. See the STORAGE section for additional in­formation.
HOW TO STOP YOUR UNIT
To stop the engine, move the ON/OFF
S
switch to the OFF position. If engine does not stop, move choke lever
S
to FULL CHOKE position.
ON/OFF Switch
Throttle Trigger
7
HOW TO START YOUR UNIT
WARNING:
turn while starting the engine. Avoid any con­tact with the muffler. A hot muffler can cause serious burns.
The trimmer head will
STARTING A COLD ENGINE (or a warm engine after running out of fuel)
Starting Position
Starter Handle
Choke Lever
Primer Bulb
1. Set unit on a flat surface.
2. Move the ON/OFF switch to the ON posi­tion.
3. Slowly press the primer bulb 6 times.
4. Move choke lever to the FULL CHOKE position.
5. Squeeze the throttle trigger fully and hold through
6. Pull starter rope handle sharply until en-
7. As soon as engine sounds as if it is trying
8. Pull starter rope sharply until engine runs,
9. Once the engine starts, allow it to run 10se-
all remaining steps.
gine sounds as if it is trying to start, but do not pull rope more than 6 times.
to start, move choke lever to the HALF CHOKE position.
but no more than 6 pulls. If the engine doesn’t start after 6 pulls (at the HALF CHOKE position), move the choke lever to the FULL CHOKE position and press the primer bulb 6 times. Squeeze and hold the throttle trigger and pull the starter rope 2 more times. Move the choke lever to the HALF CHOKE position and pull the starter rope until the engine runs, but no more than 6 pulls. it is probably flooded. Proceed to START­ING A FLOODED ENGINE.
conds, then move the choke lever to the OFF CHOKE position. Allow the unit to run for 30 more seconds at OFF CHOKE be­fore releasing the throttle trigger. engine dies with the choke lever in the OFF CHOKE position, move the choke lever to the HALF CHOKE position and pull the rope until engine runs, but no more than 6 pulls.
If engine still doesn’t start,
NOTE:
Muffler
NOTE:
STARTING A WARM ENGINE
1. Move ON/OFF switch to the ON position.
2. Move the choke lever to the HALF CHOKE position.
3. Squeeze and hold the throttle trigger. Keep throttle trigger fully squeezed until the engine runs smoothly.
4. Pull starter rope sharply until engine runs, but no more than 5 pulls.
5. Allow engine to run 15 seconds, then move the choke lever to the OFF CHOKE position.
If engine has not started, pull starter
NOTE:
rope 5 more pulls. If engine still does not run, it is probably flooded.
STARTING A FLOODED ENGINE
Flooded engines can be started by placing the choke lever in the OFF CHOKE position; then, pull the rope to clear the engine of ex­cess fuel. This could require pulling the starter handle many times depending on how badly the unit is flooded.
If the unit still doesn’t start, refer to TROUBLESHOOTING TABLE or call 1-800-554-6723.
OPERATING INSTRUCTIONS
It is recommended that the engine not be operated for longer than 1 minute at full throttle.
OPERATING POSITION
ALWAYS WEAR:
Eye Protection
Long Pants
Boots
Cut from your left to your right.
When operating unit, clip shoulder strap onto clamp, stand as shown and check for the fol­lowing:
Wear eye protection and heavy clothing.
S
Extend your left arm and hold handlebar
S
grip with your left hand. Hold throttle grip with your right hand with
S
finger on throttle trigger. Keep unit below waist level.
S
Keep shoulder strap pad centered on your
S
left shoulder and danger sign centered on
If
your back. Maintain full weight of tool on your left
S
shoulder. Without bending over, keep the blade or
S
trimmer head near and parallel to the ground and not crowded into material being cut.
8
OPERATING INSTRUCTIONS FOR USE WITH TRIMMER HEAD
WARNING:
tion. Never lean over the trimmer head. Rocks or debris can ricochet or be thrown into eyes and face and cause blindness or other serious injury.
Before trimming, bring engine to a speed suffi­cient to cut material to be trimmed.
Do not run the engine at a higher speed than necessary. The cutting line will cut efficiently when the engine is run at less than full throttle. At lower speeds, there is less engine noise and vibration. The cutting line will last longer and will be less likely to “weld” onto the spool.
Always release the throttle trigger and allow the engine to return to idle speed when not cutting.
To stop engine:
Release the throttle trigger.
S
Move the ON/OFF switch to the ON posi-
S
tion.
Always wear eye protec-
TRIMMER LINE ADVANCE
The trimmer line will advance approximately 2 in. (5 cm) each time the bottom of the trimmer head is tapped on the ground with the engine running at full throttle. The most efficient line length is the maximum length allowed by the line limiter.Always keep the shield in place when the tool is being oper­ated. To advance line:
Operate the engine at full throttle.
S
Hold the trimmer head parallel to and above
S
the grassy area. Tap the bottom of the trimmer head lightly on
S
the ground one time. Approximately 2 in. (5
cm) of line will be advanced with each tap. Always tap the trimmer head on a grassy area. Tapping on surfaces such as concrete
or asphalt can cause excessive wear to the trimmer head.If the line is worn down to 2 inches (5 cm) or less, more than one tap will be required to obtain the most efficient line length.
WARNING:
diameter line. Other sizes of line will not ad­vance properly and can cause serious injury. Do not use other materials such as wire, string, rope, etc. Wire can break off during cutting and become a dangerous missile that can cause serious injury.
Use only 0.080!(2 mm)
CUTTING METHODS
The line will easily remove grass and
S
weeds from around walls, fences, trees and flower beds, but it also can cut the tender bark of trees or shrubs and scar fences. For trimming or scalping, use less than full
S
throttle to increase line life and decrease head wear, especially:
During light duty cutting.
S
Near objects around which the line can
S
wrap such as small posts, trees or fence wire.
For mowing or sweeping, use full throttle for
S
a good clean job.
TRIMMING
head about 3 in. (8 cm) above the ground and at an angle. Allow only the tip of the line to make contact. Do not force trimmer line into work area.
Trimming
SCALPING
unwanted vegetation down to the ground. Hold the bottom of the trimmer head about 3 in. (8 cm) above the gr ound and at an angle. Allow the tip of the line to strike the ground around trees, posts, monuments, etc. This technique in­creases line wear .
-- Hold the bottom of the trimmer
-- The scalping technique removes
WARNING:
and do not crowd the line when cutting around hard objects (rock, gravel, fence posts, etc.), which can damage the trimmer head, become entangled in the line, or be thrown causing a serious hazard.
The tip of the line does the cutting. You will
S
achieve the best performance and mini-
mum line wear by not crowding the line into
the cutting area. The right and wrong ways
are shown below.
Use minimum speed
MOWING
in places conventional lawn mowers cannot reach. In the mowing position, keep the line parallel to the ground. Avoid pressing the head into the ground as this can scalp the ground and damage the tool.
-- Y our trimmer is ideal for mowing
9
SWEEPING
line can be used to blow away loose debris from an area. Keep the line parallel to and above the area surface and swing the tool from side to side.
-- The fanning action of the rotating
OPERATING INSTRUCTIONS FOR USE WITH WEED BLADE
Blade Thrust
S
when using a bladed unit. This reaction can
cause serious injury such as amputation.
Carefully study this section. It is important that
you understand what causes blade thrust,
how you can reduce the chance of its
occurring, and how you can remain in control
of unit if blade thrust occurs.
WHAT CAUSES BLADE THRUST--Blade
S
Thrust
contacts an object that it does not cut. This
contact causes the blade to stop for an instant
and then suddenly move or “thrust” away
from the object that was hit. The “thrusting”
reaction can be violent enough to cause the
operator to be propelled in any direction and
lose control of the unit. The uncontrolled unit
can cause serious injury if the blade contacts
the operator or others.
WHEN BLADE THRUST OCCURS
S
Blade Thrust
the blade snags, stalls, or binds. This is
more likely to occur in areas where it is
difficult to see the material being cut. By
using the unit properly, the occurrence of
blade thrust will be reduced and the
operator will be less likely to lose control.
is a reaction that only occurs
can occur when the spinning blade
can occur without warning if
--
Cut only grass, weeds, and woody brush up
S
to 1/2 inch in diameter with the weed blade. Do not let the blade contact material it cannot cut such as stumps, rocks, fences, metal, etc., or clusters of hard, woody brush having a diameter greater than 1/2 inch. Keep the blade sharp. A dull blade is more
S
likely to snag and thrust. Cut only at full throttle. The blade will have
S
maximum cutting power and is less likely to bind or stall. “Feed” the blade deliberately and not too
S
rapidly. The blade can thrust away if it is fed too rapidly. Cut only from your left to your right. Cutting on
S
right side of the shield will throw debris away from the operator . Use the shoulder strap and keep a firm grip
S
on the unit with both hands. A properly adjusted shoulder strap will support the weight of the unit, freeing your arms and hands to control and guide the cutting motion. Keep feet comfortably spread apart and
S
braced for a possible sudden, rapid thrust of unit. Do not overreach. Keep firm footing and balance. Keep blade below waist level; it will be
S
easier to maintain control of unit. Do not raise the engine above your waist as
S
the blade can come dangerously close to your body. Do not swing unit with such force that you
S
are in danger of losing your balance. Bring the engine to cutting speed before en­tering the material to be cut.If the blade does
not turn when you squeeze the throttle trigger, make sure tube is fully inserted into the en­gine.
Always release the throttle trigger and allow engine to return to idle speed when not cut­ting. The blade should not turn while the en­gine is running at idle. If the blade turns at idle, do not use your unit. Refer to the CARBURE­TOR ADJUSTMENT section or contact your authorized service dealer.
Maintain good firm footing while using the
S
unit. Do this by planting feet firmly in a
comfortable apart position.
Cut while swinging the upper part of your
S
body from left to right.
As you move forward to the next area to cut,
S
be sure to maintain your balance and
footing.
RECOMMENDED CUTTING POSITION
Cut using the 2 o’clock to 4 o’clock position of the blade
2 o’clock
4 o’clock
WARNING:
must not try to clear away cut material with the engine running or the blade turning to avoid serious injury. Stop engine and blade before removing materials wrapped around blade or tube.
The operator or others
10
MAINTENANCE
WARNING:
plug before performing maintenance except for carburetor adjustments.
Disconnect the spark
CHECK FOR LOOSE FASTENERS AND PARTS
Spark Plug Boot
S
Air Filter
S
Housing Screws
S
Assist Handle Screw
S
Debris Shield
S
CHECK FOR DAMAGED OR WORN PARTS
Contact an authorized service dealer for re­placement of damaged or worn parts.
ON/OFF Switch -- Ensure ON/OFF switch
S
functions properly by moving the switch to the OFF position. Make sure engine stops; then restart engine and continue. Fuel Tank -- Discontinue use of unit if fuel
S
tank shows signs of damage or leaks. Debris Shield -- Discontinue use of unit if
S
debris shield is damaged.
INSPECT AND CLEANUNIT AND DE­CALS
After each use, inspect complete unit for
S
loose or damaged parts. Clean the unit and decals using a damp cloth with a mild deter­gent. Wipe off unit with a clean dry cloth.
S
CLEAN AIR FILTER
A dirty air filter decreases engine perform­ance and increases fuel consumption and harmful emissions. Always clean after every 5 hours of operation.
1. Clean the cover and the area around it to keep dirt from falling into the carburetor chamber when the cover is removed.
2. Remove parts as illustrated.
NOTE:
producing harmful evaporative emissions, do not clean filter in gasoline or other flammable solvent.
3. Wash the filter in soap and water.
4. Allow filter to dry.
5. Add a few drops of oil to the filter;
6. Replace parts.
To avoid creating a fire hazard or
squeeze the filter to distribute oil.
Air filter
Screws
Air filter cover
INSPECT MUFFLER AND SPARK ARRESTING SCREEN
As your unit is used, carbon deposits build up on the muffler and spark arresting screen. For normal homeowner use, the muffler and spark arresting screen will not require any service. After 50 hours of use, we recom­mend that your muffler be serviced or re­placed by your authorized service dealer.
REPLACE SPARK PLUG
Replace the spark plug each year to ensure the engine starts easier and runs better. Set spark plug gap at 0.025 in. Ignition timing is fixed and nonadjustable.
1. Twist, then pull off spark plug boot.
2. Remove spark plug from cylinder and discard.
3. Replace with Champion RCJ-6Y spark plug and tighten securely with a 3/4 in. socket wrench.
4. Reinstall the spark plug boot.
11
SERVICE AND ADJUSTMENTS
REPLACING THE LINE
1. Remove spool by firmly pulling on tap button.
2. Clean entire surface of hub and spool.
3. Replace with a pre-wound spool, or cut two lengths of meter Weed Eaterrbrand line.
WARNING:
string, etc., which can break off and become a dangerous missile.
4. Insert ends of the lines about 1/2 inch (1 cm) into the small holes on the inside of spool.
Spool
Line exit holes
Hub
feet of 0.080!(2 mm) dia-
12-1/2
Never use wire, rope,
Line in Notch
Line in Notch
Small Holes
STORAGE
5. Wind the line evenly and tightly onto the spool. Wind in the direction of the arrows found on the spool.
6. Push the lines into the notches, leaving 3 to 5 inches (7 -- 12 cm) unwound.
7. Insert the lines into the the exit holes in the hub as shown in the illustration.
8. Align the notches with the line exit holes.
9. Push spool into hub until it snaps into place.
10. Pull the lines extending outside of the hub to release the lines from the notches.
BLADE REPLACEMENT
Refer to the ASSEMBLY section for blade re­placement instructions and illustrations.
CARBURETOR ADJUSTMENT
Your carburetor is equipped with limiter caps. Carburetor adjustment is a complicated task. We recommend that you take your unit to an authorized service dealer. Damage will occur if you turn the needles beyond the limiter stops.
WARNING:
steps after each use:
Allow engine to cool before storing or trans-
S
porting. Store unit and fuel in a well ventilated area
S
where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. Store unit with all guards in place. Position
S
unit so that any sharp object cannot acci­dentally cause injury. Store unit and fuel well out of the reach of
S
children.
Perform the following
SEASONAL STORAGE
Prepare unit for storage at end of season or if it will not be used for 30 days or more. If your unit is to be stored for a period of time:
Clean the entire unit before lengthy
S
storage. Store in a clean dry area.
S
Lightly oil external metal surfaces.
S
FUEL SYSTEM
Under FUELING ENGINE in the OPERA­TION section of this manual, see message la-
IMPORTANT
beled sohol in your engine.
regarding the use of ga-
Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to the gasoline in the fuel tank or fuel storage container. Fol­low the mix instructions found on stabilizer container. Run engine at least 5 minutes after adding stabilizer.
ENGINE
Remove spark plug and pour 1 teaspoon of
S
40:1, 2-cycle engine oil (air cooled) through the spark plug opening. Slowly pull the starter rope 8 to 10 times to distribute oil. Replace spark plug with new one of recom-
S
mended type and heat range. Clean air filter.
S
Check entire unit for loose screws, nuts,
S
and bolts. Replace any damaged, broken, or worn parts. At the beginning of the next season, use
S
only fresh fuel having the proper gasoline to oil ratio.
OTHER
Do not store gasoline from one season to
S
another. Replace your gasoline can if it starts to rust.
S
12
TROUBLESHOOTING TABLE
WARNING:
recommended remedies below except remedies that require operation of the unit.
Always stop unit and disconnect spark plug before performing all of the
TROUBLE CAUSE REMEDY
Engine will not start.
Engine will not idle properly.
Engine will not accelerate, lacks power, or dies under a load.
Engine smokes excessively.
Engine runs hot.
1.ON/OFF switch in OFF position.
2. Engine flooded.
3. Fuel tank empty.
4. Spark plug not firing.
5. Fuel not reaching
carburetor.
6. Carburetor requires
adjustment.
1. Carburetor requires
adjustment.
2. Crankshaft seals worn.
3. Compression low.
1. Air filter dirty.
2. Spark plug fouled.
3. Carburetor requires
adjustment.
4. Carbon build-up on
muffler outlet screen.
5. Compression low.
1. Choke partially on.
2. Fuel mixture incorrect.
3. Air filter dirty.
4. Carburetor requires
adjustment.
1. Fuel mixture incorrect.
2. Spark plug incorrect.
3. Carburetor requires adjustment.
4. Carbon build-up on muffler outlet screen.
1. Move ON/OFF switch to ON position.
2. See “Starting a Flooded Engine” in Operation Section.
3. Fill tank with correct fuel mixture.
4. Install new spark plug.
5. Check for dirty fuel filter; replace. Check for kinked or split fuel line; repair or replace.
6. See “Carburetor Adjustment” in Service and Adjustments Section.
1. See “Carburetor Adjustment” in Service and Adjustments Section.
2. Contact an authorized service dealer.
3. Contact an authorized service dealer.
1. Clean or replace air filter.
2. Clean or replace plug and regap.
3. See “Carburetor Adjustment” in Service and Adjustments Section.
4. Contact an authorized service dealer.
5. Contact an authorized service dealer.
1. Adjust choke.
2. Empty fuel tank and refill with correct fuel mixture.
3. Clean or replace air filter.
4. See “Carburetor Adjustment” in Service and Adjustments Section.
1. See “Fueling Engine” in Operation section.
2. Replace with correct spark plug.
3. See “Carburetor Adjustment” in Service and Adjustments Section.
4. Contact an authorized service dealer.
13
LIMITED WARRANTY
ELECTROLUX HOME PRODUCTS, INC.,
warrants to the original purchaser that each
Weed Eater
new tachment is free from defects in material and workmanship and agrees to repair or replace under this warranty any defective gasoline product or attachment as follows from the original date of purchase.
2 YEARS
household purposes.
90 DA YS
commercial, professional, or income produc­ing purposes.
30 DAYS
purposes. This warranty is not transferable and does not cover damage or liability caused by improper handling, improper maintenance, or the use of accessories and/or attachments not spe­cifically recommended by
HOME PRODUCTS, INC.,
tionally, this warranty does not cover tune­ups, spark plugs, filters, cutting line, or rotat­ing head parts that will wear and require replacement with reasonable use during the warranty period. This warranty does not cov-
-- Parts and Labor, when used for
-- Parts and Labor, when used for
-- Parts and Labor, if used for rental
brand gasoline tool or at-
r
ELECTROLUX
for this tool. Addi-
U.S. EPA/CALIFORNIA EMISSION CONTROL
WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OB­LIGATIONS:
Protection Agency/California Air Resources Board and POULAN/WEED EATER, DIVI­SION OF WCI OUTDOOR PRODUCTS are pleased to explain the emissions control sys­tem warranty on your year 2001--2004 small off--road engine. In California, all new small off--road engines must be designed, built, and equipped to meet the State’s stringent anti-­smog standards. POULAN/WEED EATER must warrant the emission control system on your small off--road engine for the periods of time listed below provided there has been no abuse, neglect, or improper maintenance of your small off--road engine. Your emission control system includes parts such as the carburetor and the ignition system. Where a warrantable condition exists, POULAN/ WEED EATER will repair your small off --road engine at no cost to you. Expenses covered under warranty include diagnosis, parts and labor.
COVERAGE:
on your engine (as listed under Emissions Control Warranty Parts List) is defective or a defect in the materials or workmanship of the engine causes the failure of such an emission related part, the part will be repaired or re­placed by POULAN/WEED EATER.
ER’S WARRANTY RESPONSIBILITIES:
As the small off--road engine owner, you are responsible for the performance of the re­quired maintenance listed in your instruction manual. POULAN/WEED EATER recom­mends that you retain all receipts covering
The U.S. Environmental
MANUFACTURER’S WARRANTY
If any emissions related part
OWN-
er predelivery setup or normal adjustments explained in the instruction manual.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.NO CLAIMS FOR CON­SEQUENTIAL OR OTHER DAMAGES WILL BE ALLOWED, AND THERE ARE NO OTHER EXPRESS WARRANTIES EX­CEPT THOSE EXPRESSLY STIPULATED HEREIN. SOME STATES DO NOT ALLOW LIMITA­TIONS ON HOW LONG AN IMPLIED WAR­RANTY LASTS OR THE EXCLUSION OR LIMITATIONS OF INCIDENTAL OR CON­SEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSION MAY NOT APPLY TO YOU. The policy of
UCTS, INC.,
products. Therefore,
PRODUCTS, INC.,
change, modify, or discontinue models, de­signs, specifications, and accessories of all products at any time without notice or obliga­tion to any purchaser.
maintenance on your small off--road engine, but POULAN/WEED EATER cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance. As the small off-­road engine owner, you should be aware that POULAN/WEED EATER may deny you war­ranty coverage if your small off--road engine or a part of it has failed due to abuse, neglect, improper maintenance, unapproved modifi­cations, or the use of parts not made or ap­proved by the original equipment manufactur­er. You are responsible for presenting your small off--road engine to a POULAN/WEED EATER authorized repair center as soon as a problem exists. Warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days. If you have any ques­tions regarding your warranty rights and re­sponsibilities, you should contact your near­est authorized service center or call POULAN/WEED EATER at 1--800--554--6723.
MENCEMENT DATE:
begins on the date the small off--road engine is purchased. This warranty shall be for a period of two years from the initial date of purchase.
IS COVERED: REPAIR OR REPLACE­MENT OF PARTS.
any warranted part will be performed at no charge to the owner at an approved POU­LAN/WEED EATER servicing center. If you have any questions regarding your warranty rights and responsibilities, you should contact your nearest authorized service center or call
ELECTROLUX HOME PROD-
is to continuously improve its
ELECTROLUX HOME
reserves the right to
WARRANTY COM-
The warranty period
LENGTH OF COVERAGE:
WHAT
Repair or replacement of
14
POULAN/WEED EATER at 1--800--554--6723 Any warranted part which is not scheduled for replacement as required maintenance, or which is scheduled only for regular inspection to the effect of “repair or replace as neces­sary” shall be warranted for 2 years. Any war­ranted part which is scheduled for replace­ment as required maintenance shall be warranted for the period of time up to the first scheduled replacement point for that part.
DIAGNOSIS:
charged for diagnostic labor which leads to the determination that a warranted part is de­fective if the diagnostic work is performed at an approved POULAN/WEED EATER serv­icing center.
AGES:
POULAN/WEED EATER may be li­able for damages to other engine components caused by the failure of a war­ranted part still under warranty.
NOT COVERED
abuse, neglect, or improper maintenance are not covered.
PARTS:
can be grounds for disallowing a warranty
The use of add--on or modified parts
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
WARRANTY PERIOD:
The owner shall not be
CONSEQUENTIAL DAM-
WHAT IS
: All failures caused by
ADD--ON OR MODIFIED
claim. POULAN/WEED EATER is not liable to cover failures of warranted parts caused by the use of add --on or modified parts.
FILE A CLAIM:
garding your warranty rights and responsibili­ties, you should contact your nearest autho­rized service center or call POULAN/WEED EATER at 1--800--554--6723.
GET WARRANTY SERVICE:
vices or repairs shall be provided at all POU­LAN/WEED EATER service centers. call: 1--800--554--6723
PLACEMENT AND REPAIR OF EMISSION RELATED PARTS
EATER approved replacement part used in the performance of any warranty mainte­nance or repair on emission related parts will be provided without charge to the owner if the part is under warranty.
TROL WARRANTY PARTS LIST:
tor, Ignition System: Spark Plug (covered up to maintenance schedule), Ignition Module, Muffler including catalyst.
STATEMENT:
the performance of all required maintenance as defined in the instruction manual.
If you have any questions re-
MAINTENANCE, RE-
: Any POULAN/WEED
The owner is responsible for
HOW TO
WHERE TO
Warranty ser-
EMISSION CON-
Carbure-
MAINTENANCE
15
Loading...