Quick start guide
Model: VCS850
ErisStation
TM
businessphones.vtech.com
SIP DECT Expansion Wireless Speakerphone
Congratulations
on purchasing your new VTech product.
For support, shopping, and everything new at VTech, visit
our website at businessphones.vtech.com.
The VCS850 Wireless Speakerphone extends the range
of the VCS752 SIP Conference Phone. Register up to
three VCS850 Wireless Speakerphones to continue
conversations anywhere in a large conference room.
Installing the wireless speaker battery
• Risk of explosion! Batteries should not be exposed to
excessive heat such as bright sunlight or re.
• Use only the supplied battery.
• Risque d’explosion! Le bloc-piles ne doit pas être exposé à
la chaleur excessive telle que la lumière du soleil ou au feu.
• N’utilisez que la pile incluse.
1. After removing the battery door, plug the battery connector
securely into the socket inside the battery compartment.
2. Place the battery into the battery compartment.
3. Attach the battery door until it clicks into place.
Connecting power to the VCS850
1. Plug one end of the AC adapter into the power jack on the
bottom of the unit.
2. Route the cord through the slots.
3. Plug the large end of the AC adapter into a wall outlet not
controlled by a switch.
• After connecting power, the VCS850 LEDs should ash red
and green, indicating the unit is ready for registration.
• The supplied power adapter is designed for use with only
the VCS850. It is not designed to power other devices.
Do not connect the supplied power adapter to any other
devices.
• The AC power cord is intended for a vertical or oor mount
position. The prongs are not designed to hold the plug in
place if it is plugged into a ceiling or cabinet outlet.
®
1. Microphone
2. Speaker
3. MUTE ALL
During a ca ll, press to
mute or end mute a ll
microphones in the
system.
4.
Press to answer or end
a call.
5. Multipurpose LEDs (four)
6.
/
• Press to adjust the
ringer volume.
• During a call, press
to adjust the listening
volume.
7. Microphone
1
2
5
3
4
6
7
LED color and behavior VCS850 Status
GREEN
Steady
Flashing
Flashing (with red LED)
Slow ash
On for 5 secs
• Call active, speaker on
• Incoming call
• Ready for registration
• Paged by base
• Successfully registered
RED
Flashing (with green LED)
On for 5 secs
Steady
Slow ash
• Ready for registration
• Registration failed
• Microphone muted
• Out of range, deregistered
ORANGE
Steady
On for 5 secs
• Reset mode
• Power on
Charge LED
• On when charging
• Off when charging is complete
• Flashes when battery is low
Compliance
FCC Part 15
This equipment has been tested and found to comply
with the requirements for a Class B digital device under
Part 15 of the Federal Communications Commission
(FCC) rules. These requirements are intended to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician
for help.
Changes or modications to this equipment not expressly
approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2)
this device must accept any interference received, including
interference that may cause undesired operation. Privacy
of communications may not be ensured when using this
telephone.
To ensure safety of users, the FCC has established criteria
for the amount of radio frequency energy that can be safely
absorbed by a user or bystander according to the intended
usage of the product. This product has been tested and
found to comply with the FCC criteria. The wireless mic may
be safely held against the ear of the user. The telephone
base shall be installed and used such that parts of the user’s
body other than the hands are maintained at a distance of
approximately 20 cm (8 inches) or more.
This Class B digital apparatus complies with Canadian
requirement CAN ICES-3 (B)/NMB-003(B)
Cet appareil numérique de la classe B est conforme à la
norme NMB-003 du Canada.
Industry Canada
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device
must accept any interference, including interference that may
cause undesired operation of the device.
Privacy of communications may not be ensured when using
this telephone.
The term ‘’IC:‘’ before the certication/registration number
only signies that the Industry Canada technical specications
were met.
This product meets the applicable Innovation, Science and
Economic Development Canada technical specications.
Specications
Frequency control Crystal controlled PLL synthesizer
Transmit frequency 1921.536–1928.448 MHz
Channels 5
Nominal effective
range
Maximum power allowed by FCC
and IC. Actual operating range may
vary according to environmental
conditions at the time of use.
Power requirements Ni-MH Battery Pack; 7.2V; 2100mAH
rechargeable battery
Base unit adapter:
Input: 100 –240V AC 50/60Hz
Output: 12V DC @ 1.0A
Register the Wireless Speakerphone
You must register the VCS850 using the menus on the
VCS752 SIP Conference Phone.
1. On the VCS752 SIP Conference Phone, press MENU.
2. On the Main Menu, highlight User settings and then press
SELECT.
3. On the User settings menu, highlight Wireless speaker.
4. With Register highlighted, press SELECT.
The screen displays Registering... and then Registration
succeeded. The base plays a conrmation tone. The
registered speaker LEDs stop ashing red and green. The
LEDs turn green briey and then turn off.
5. Repeat steps 1 to 4 for any additional wireless speakers.
• If a speakerphone fails to register, the base unit will
display Registration failed.
• To cancel registration, press Cancel.
For complete operating instructions, see the VCS850 User
Guide, available from our website at
businessphones.vtech.com.
Specic ations are subject to c hange without notic e.
© 2016 for VTech Com munications, I nc.
All right s reserved. 10/16. VCS 850_QSG_V1
Loading...