TP-Link TD-W8961ND User Guide

TD-W8961ND

Rev:3.1.1 1910011218

300Mbps Wireless N ADSL2+ Modem Router

Specifications are subject to change without notice. is a registered trademark

of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or

registered trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or used to make any

derivative such as translation, transformation, or adaptation without permission from TP-LINK

reserved.

http://www.tp-link.com

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/ TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may

cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

Note: The manufacturer is not responsible for any radio or TV interference caused by

unauthorized modifications to this equipment. Such modifications could void the user’s authority

to operate the equipment.

FCC RF Radiation Exposure Statement

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled

environment. This device and its antenna must not be co-located or operating in conjunction with

any other antenna or transmitter.

“To comply with FCC RF exposure compliance requirements, this grant is applicable to only

Mobile Configurations. The antennas used for this transmitter must be installed to provide a

separation distance of at least 20 cm from all persons and must not be co-located or operating in

conjunction with any other antenna or transmitter.”

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in

which case the user may be required to take adequate measures.

Canadian Compliance Statement

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject

to the following two conditions:

(1) This device may not cause interference, and

(2)This device must accept any interference, including interference that may cause undesired

operation of the device.

Cet appareil est conforme aux norms CNR exemptes de licence d’Industrie Canada. Le

fonctionnement est soumis aux deux conditions suivantes:

(1) cet appareil ne doit pas provoquer d’interférences et

(2) cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un

fonctionnement non souhaité de l’appareil.

This device has been designed to operate with the antennas listed below, and having a maximum

gain of 3 dBi. Antennas not included in this list or having a gain greater than 3 dBi are strictly

prohibited for use with this device. The required antenna impedance is 50 ohms.

To reduce potential radio interference to other users, the antenna type and its gain should be so

chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for

successful communication.

Industry Canada Statement

Complies with the Canadian ICES-003 Class B specifications.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

This device complies with RSS 210 of Industry Canada. This Class B device meets all the

requirements of the Canadian interference-causing equipment regulations.

Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le

matériel brouilleur du Canada.

Korea Warning Statements:

당해 무선설비는 운용중 전파혼신 가능성이 있음.

NCC Notice & BSMI Notice

注意！

依據低功率電波輻射性電機管理辦法第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性或功能。

第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。低功率射頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。減少電磁波影響，請妥適使用。

安全諮詢及注意事項

●請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。

●清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。

●注意防潮，請勿將水或其他液體潑灑到本產品上。

●插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。

●請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。

●請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。

UkrSEPRO

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам

нормативних документів та вимогам, що передбачені чинними законодавчими актами

України.

Safety Information

 When product has power button, the power button is one of the way to shut off the product;

when there is no power button, the only way to completely shut off power is to disconnect the

product or the power adapter from the power source.

 Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock

and voiding the limited warranty. If you need service, please contact us.

 Avoid water and wet locations.

This product can be used in the following countries:

AT BG BY CA CZ DE DK EE

ES FI FR GB GR HU IE IT

LT LV MT NL NO PL PT RO

RU SE SK TR UA US

：

DECLARATION OF CONFORMITY

For the following equipment:

Product Description: 300Mbps Wireless N ADSL2+ Modem Router

Model No.: TD-W8961ND

Trademark: TP-LINK

We declare under our own responsibility that the above products satisfy all the technical

regulations applicable to the product within the scope of Council Directives:

Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC, Directives 1999/519/EC,

Directives 2011/65/EU

The above product is in conformity with the following standards or other normative documents

EN 300328 V1.8.1

ETSI EN 301 489-1 V1.9.2:2011& EN301489-17 V2.2.1

EN 55022:2010

EN 55024:2010

EN 61000-3-2:2006+A1:2009+A2:2009

EN 61000-3-3:2008

EN60950-1:2006+A11

EN62311:2008

2009+A1:2010+A12:2011

The product carries the CE Mark:

Person responsible for making this declaration:

Yang Hongliang

Product Manager of International Business

Date of issue: 2015

TP-LINK TECHNOLOGIES CO., LTD.

Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park,

Shennan Rd, Nanshan, Shenzhen, China

CONTENTS

Package Contents .................................................................................................... 1

Chapter 1 Introduction ......................................................................................... 2

1.1 Product Overview .................................................................................. 2

1.2 Main Features ....................................................................................... 2

1.3 Conventions .......................................................................................... 3

Chapter 2 Hardware Installation .......................................................................... 4

2.1 The Front Panel .................................................................................... 4

2.2 The Back Panel ..................................................................................... 6

2.3 Installation Environment ........................................................................ 7

2.4 Connecting the Modem Router ............................................................. 7

Chapter 3 Quick Installation Guide ..................................................................... 9

3.1 TCP/IP Configuration ............................................................................ 9

3.2 Login ................................................................................................... 10

Chapter 4 Software Configuration .................................................................... 13

4.1 Status .................................................................................................. 13

4.1.1 Device Info ............................................................................................... 13

4.1.2 System Log .............................................................................................. 14

4.1.3 Statistics .................................................................................................. 15

4.2 Quick Start .......................................................................................... 18

4.3 Interface Setup .................................................................................... 18

4.3.1 Internet .................................................................................................... 18

4.3.2 LAN ......................................................................................................... 22

4.3.3 Wireless ................................................................................................... 26

4.4 Advanced Setup .................................................................................. 37

4.4.1 Firewall .................................................................................................... 37

4.4.2 Routing .................................................................................................... 38

4.4.3 NAT ......................................................................................................... 39

4.4.4 QoS ......................................................................................................... 42

4.4.5 VLAN ....................................................................................................... 44

4.4.6 ADSL ....................................................................................................... 46

4.5 Access Management ........................................................................... 47

4.5.1 ACL ......................................................................................................... 47

4.5.2 Filter ........................................................................................................ 48

4.5.3 SNMP ...................................................................................................... 56

4.5.4 UPnP ....................................................................................................... 56

4.5.5 DDNS ...................................................................................................... 57

4.5.6 CWMP ..................................................................................................... 57

4.6 Maintenance ........................................................................................ 58

4.6.1 Administration .......................................................................................... 59

4.6.2 Time Zone ............................................................................................... 59

4.6.3 Firmware.................................................................................................. 61

4.6.4 SysRestart ............................................................................................... 63

4.6.5 Diagnostics .............................................................................................. 63

4.7 Help ..................................................................................................... 64

Appendix A: Specifications ................................................................................... 66

Appendix B: Configuring the PC ........................................................................... 67

Appendix C: Troubleshooting ............................................................................... 71

Appendix D: Technical Support ............................................................................ 75

Technical Support .................................................................................................. 75

TD-W8961ND

300Mbps Wireless N ADSL2+ Modem Router User Guide



Package Contents

The following contents should be found in your package:

 One TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router

 One Power Adapter for TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router

 Quick Installation Guide

 One RJ45 cable

 Two RJ11 cables

 One ADSL splitter

 One Resource CD which includes this User Guide

Note:

Make sure that the package contains the above items. If any of the listed items are damaged or

missing, please contact your distributor.

TD-W8961ND

300Mbps Wireless N ADSL2+ Modem Router User Guide

Chapter 1 Introduction

Thank you for choosing the TD-W8961ND 300Mbps Wireless N ADSL2+ Modem Router.

1.1 Product Overview

The device is designed to provide a simple and cost-effective ADSL Internet connection for a

private Ethernet or IEEE 802.11n/ IEEE 802.11g/ IEEE 802.11b wireless network.

The TD-W8961ND connects to an Ethernet LAN or computers via standard Ethernet ports. The

ADSL connection is made using ordinary telephone line with standard connectors. Multiple

workstations can be networked and connected to the Internet using a single Wide Area Network

(WAN) interface and single global IP address. The advanced security enhancements, IP/MAC

Filter, Application Filter and URL Filter can help to protect your network from potentially

devastating intrusions by malicious agents from the outside of your network.

Quick Start of the Web-based Utility is supplied and friendly help messages are provided for the

configuration. Network and Router management is done through the Web-based Utility which can

be accessed through local Ethernet using any web browser.

ADSL

The TD-W8961ND supports full-rate ADSL2+ connectivity conforming to the ITU and ANSI

specifications. In addition to the basic DMT physical layer functions, the ADSL2+ PHY supports

dual latency ADSL2+ framing (fast and interleaved) and the I.432 ATM Physical Layer.

Wireless

In the most attentive wireless security, the modem router provides multiple protection measures. It

can be set to turn off the wireless network name (SSID) broadcast so that only stations that have

the SSID can be connected. The modem router provides wireless LAN 64/128-bit WEP encryption

security, WPA-PSK/WPA2-PSK authentication, as well as TKIP/AES encryption security.

1.2 Main Features

 Four 10/100Mbps Auto-Negotiation RJ45 LAN ports (Auto MDI/MDIX), one RJ11 port.

 Provides external splitter.

 Adopts Advanced DMT modulation and demodulation technology.

 Supports bridge mode and Router function.

 Multi-user sharing a high-speed Internet connection.

 Downstream data rates up to 24Mbps, upstream data rates up to 3.5Mbps (With Annex M

enabled).

 Supports long transfers, the max line length can reach to 6.5Km.

 Supports remote configuration and management through SNMP

and CWMP.

TD-W8961ND

300Mbps Wireless N ADSL2+ Modem Router User Guide

 Supports PPPoE, it allows connecting the internet on demand and disconnecting from the

Internet when idle.

 Provides reliable ESD and surge-protect function with quick response semi-conductive surge

protection circuit.

 High speed and asymmetrical data transmit mode, provides safe and exclusive bandwidth.

 Supports All ADSL industrial standards.

 Compatible with all mainstreams DSLAM (CO).

 Provides integrated access of internet and route function which face to SOHO user.

 Real-time Configuration and device monitoring.

 Supports Multiple PVC (Permanent Virtual Circuit).

 Built-in DHCP server.

 Built-in firewall, supporting IP/MAC filter, Application filter and URL filter.

 Supports Virtual Server, DMZ host and IP Address Mapping.

 Supports Dynamic DNS, UPnP and Static Routing.

 Supports system log and flow Statistics.

 Supports firmware upgrade and Web management.

 Provides WPA-PSK/WPA2-PSK data security, TKIP/AES encryption security.

 Provides 64/128-bit WEP encryption security and wireless LAN ACL (Access Control List).

1.3 Conventions

The modem router or device mentioned in this User Guide stands for TD-W8961ND without any

explanations.

Parameters provided in the pictures are just references for setting up the product, which may

differ from the actual situation.

TD-W8961ND

300Mbps Wireless N ADSL2+ Modem Router User Guide

There is no successful Internet connection or the modem

modem router is sending or receiving data over the

button on other wireless

function is

Chapter 2 Hardware Installation

2.1 The Front Panel

Figure 2-1

The LEDs locate on the front panel. They indicate the device’s working status. For details, please

refer to LED Explanation.

LED Explanation:

Name Status Indication

(Power)

(ADSL)

(INTERNET)

(WLAN)

Off

Flash

Off

Flash

Off

On Wireless is enabled but no data is being transmitted.

Flash

The modem router is powered on.

The modem router is off. Please ensure that the power adapter

is connected correctly.

ADSL line is synchronized and ready to use.

The ADSL negotiation is in progress.

ADSL synchronization fails. Please refer to Note 1

troubleshooting.

The network is available with a successful Internet connection.

There is data being transmitted or received via the Internet.

router is operating in Bridge mode. Please refer to Note 2 for

troubleshooting.

The

wireless network.

for

Off Wireless function is disabled.

A wireless device has been successfully added to the network

(WPS)

Flash

Off

by WPS function.

handshaking is in process and will continue for about 2

WPS

minutes. Please press the WPS

devices that you want to add to the network while the LED is

flashing.

The WPS function is disabled or the wireless device fails to be

added to the network in 2 minutes after WPS

TD-W8961ND

300Mbps Wireless N ADSL2+ Modem Router User Guide

for more



enabled. Please refer to 4.3.3 WPS Settings

information.

(LAN1-4)

Note:

1. If the ADSL LED is off, please check your Internet connection first. Refer to 2.4 Connecting

the Router for more information about how to make Internet connection correctly. If you have

already made a right connection, please contact your ISP to make sure if your Internet service

is available now.

2. If the Internet LED is off, please check your ADSL LED first. If your ADSL LED is also off,

please refer to Note 1

configuration. You may need to check this part of information with your ISP and make sure

everything have been input correctly. Refer to

information.

Flash

Off

. If your ADSL LED is GREEN ON, please check your Internet

There is a device connected to this LAN port.

The modem router is sending or receiving data over this LAN

port.

There is no device connected to this LAN port.

4.1.1 Device Info and 4.3.1 Internet for more

TD-W8961ND

300Mbps Wireless N ADSL2+ Modem Router User Guide

2.2 The Back Panel

Figure 2-2

 POWER: The Power plug is where you will connect the power adapter.

 ON/OFF: The switch for the power.

 WPS: The switch for the WPS function. For details, please refer to

Settings.

 RESET: There are two ways to reset the modem router 's factory defaults.

Method one: With the modem router powered on, use a pin to press and hold the Reset

button for at least 5 seconds. And the modem router will reboot to its factory default settings.

Method two: Restore the default setting from “Maintenance-SysRestart” of the modem router

's Web-based Utility.

 WiFi: The switch for the WiFi function.

 1, 2, 3, 4 (LAN): Through the port, you can connect the modem router to your PC or the other

Ethernet network devices.

 ADSL: Through the port, you can connect the modem router with the telephone. Or you can

connect them by an external separate splitter. For details, please refer to

Modem Router.

4.3.3.1 Wireless-WPS

2.4 Connecting the

TD-W8961ND

300Mbps Wireless N ADSL2+ Modem Router User Guide

：

 Antennas: Used for wireless operation and data transmit.

2.3 Installation Environment

 The Product should not be located where it will be exposed to moisture or excessive heat.

 Place the modem router in a location where it can be connected to the various devices as

well as to a power source.

 Make sure the cables and power cord are safely placed out of the way so they do not create a

tripping hazard.

 The modem router can be placed on a shelf or desktop.

 Keep away from the strong electromagnetic radiation and the device of electromagnetic

sensitive.

2.4 Connecting the Modem Router

Before installing the device, please make sure your broadband service provided by your ISP is

available. If there is any problem, please contact your ISP. Before cable connection, cut off the

power supply and keep your hands dry. You can follow the steps below to install it.

Step 1: Connect the ADSL Line.

Method one: Plug one end of the twisted-pair ADSL cable into the ADSL port on the rear

panel of TD-W8961ND, and insert the other end into the wall socket.

Method two

voice, and then you can access the Internet and make calls at the same time. The

external splitter has three ports:

• LINE: Connect to the wall jack

• PHONE: Connect to the phone sets

• MODEM: Connect to the ADSL port of TD-W8961ND

Plug one end of the twisted-pair ADSL cable into the ADSL port on the rear panel of TD-W8961ND. Connect the other end to the MODEM port of the external splitter.

Step 2: Connect the Ethernet cable. Attach one end of a network cable to your computer’s

Ethernet port or a regular hub/switch port, and the other end to the LAN port on the

TD-W8961ND.

Step 3: Power on the computers and LAN devices.

Step 4: Attach the power adapter. Connect the power adapter to the power connector on the rear

of the device and plug in the adapter to a electrical outlet or power extension. The

You can use a separate splitter. External splitter can divide the data and

electrical outlet shall be installed near the device and shall be easily accessible.

TD-W8961ND

300Mbps Wireless N ADSL2+ Modem Router User Guide

Figure 2-3

TD-W8961ND

300Mbps Wireless N ADSL2+ Modem Router User Guide

Chapter 3 Quick Installation Guide

This chapter will show you how to configure the basic functions of your TD-W8961ND 300Mbps

Wireless N ADSL2+ Modem Router using Quick Setup Wizard within minutes.

3.1 TCP/IP Configuration

The default IP address of the TD-W8960N 300Mbps Wireless N USB ADSL2+ Modem Router is

192.168.1.1. And the default Subnet Mask is 255.255.255.0. These values can be changed as

you desire. In this guide, we use all the default values for description.

Connect the local PC to the LAN/WAN port of the Modem Router. Configure your PC to obtain IP

address automatically in the following way.

 Obtain an IP address automatically

1) Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your PC.

If you need instructions as to how to do this, please refer to

PC”.

2) Then the built-in DHCP server will assign IP address for the PC.

Now, you can run the Ping command in the command prompt to verify the network connection.

Please click the Start menu on your desktop, select run tab, type cmd or command in the field

and press Enter. Type ping 192.168.1.1 on the next screen, and then press Enter.

If the result displayed is similar to the screen below, the connection between your PC and the

router has been established.

Appendix B: "Configuring the

Figure 3-1

If the result displayed is similar to the screen shown below, it means that your PC has not

connected to the router.

TD-W8961ND

300Mbps Wireless N ADSL2+ Modem Router User Guide

Figure 3-2

You can check it following the steps below:

1) Is the connection between your PC and the router correct?

The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should

be lit.

2) Is the TCP/IP configuration for your PC correct?

If the router's IP address is 192.168.1.1, your PC's IP address must be within the range of

192.168.1.2 ~ 192.168.1.254.

3.2 Login

Once your host PC is properly configured, please proceed as follows to use the Web-based Utility:

Start your web browser and type the private IP address of the modem router in the URL field:

192.168.1.1.

After that, you will see the screen shown below, enter the default User Name admin and the

default Password admin, and then click OK to access to the Quick Start screen. You can follow

the steps below to complete the Quick Start.

Figure 3-3

TD-W8961ND

300Mbps Wireless N ADSL2+ Modem Router User Guide

Step 1: Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen.

Click the NEXT button.

Figure 3-4

Step 2: Configure the time for the modem router, and then click the NEXT button.

Figure 3-5

Step 3: Select the connection type to connect to the ISP (We select PPPoE/PPPoA mode for

example here), and then click the NEXT button.

Figure 3-6

Step 4: Configure the following options provided by your ISP: Username, Password, VPI, VCI

and Connection Type. Then click NEXT.

TD-W8961ND

300Mbps Wireless N ADSL2+ Modem Router User Guide



Figure 3-7

Step 5: Configure the rules for the WLAN, and click NEXT.

Figure 3-8

Note:

If the Access Point is activated, the wireless function will be available even without the external antenna because of an additional printed antenna. To adopt the wireless security protection measures, please refer to section 4.3.3.

Step 6: Click NEXT to finish the Quick Start.

Figure 3-9

TD-W8961ND

300Mbps Wireless N ADSL2+ Modem Router User Guide

Chapter 4 Software Configuration

This User Guide recommends using the “Quick Installation Guide” for first-time installation. For

advanced users, if you want to know more about this device and make use of its functions

adequately, maybe you will get help from this chapter to configure the advanced settings through

the Web-based Utility.

After your successful login, you can configure and manage the device. There are main menus on

the top of the Web-based Utility; submenus will be available after you click one of the main menus.

On the center of the Web-based Utility, there are the detailed configurations or status information.

To apply any settings you have altered on the page, please click the SAVE button.

4.1 Status

Choose “Status”, you can see the next submenus: Device Info, System Log and Statistics.

Click any of them, and you will be able to configure the corresponding function.

Figure 4-1

Click any of them, and you will be able to view the corresponding information.

4.1.1 Device Info

Choose “Status→Device Info” menu, and you will be able to view the device information,

including LAN, WAN and ADSL. The information will vary depending on the settings of the modem

router configured on the Interface Setup screen.

TD-W8961ND

300Mbps Wireless N ADSL2+ Modem Router User Guide



Figure 4-2

Note:

Click the other submenus System Log or Statistics in Figure 4-2, and you will be able to view the

system log and traffic statistics about the modem router.

4.1.2 System Log

Choose “Status→System Log” menu, and you will be able to query the logs of the modem

router.

TD-W8961ND

300Mbps Wireless N ADSL2+ Modem Router User Guide

Figure 4-3

The modem router can keep logs of all traffic. You can query the logs to find what happened to the

modem router.

Click the CLEAR LOG button to clear the logs.

Click the SAVE LOG button to save the logs.

4.1.3 Statistics

Choose “Status→Statistics” menu, and you will be able to view the network traffic over Ethernet,

ADSL and WLAN.

TD-W8961ND

300Mbps Wireless N ADSL2+ Modem Router User Guide

Figure 4-4

 Interface: You can select Ethernet, ADSL and WLAN to view the corresponding network

traffic over different ports.

 Select Ethernet, and you will see the statistics table as below.

Statistics Table:

The frames transmitted over the Ethernet port.

The multicast frames transmitted over the Ethernet

port.

The total bytes transmitted over the Ethernet port.

The collision occurred over the Ethernet port when

data is being transmitted.

The error frames over the Ethernet port when data is

being transmitted.

Transmit

Statistics

Transmit Frames

Transmit Multicast Frames

Transmit total Bytes

Transmit Collision

Transmit Error Frames

Receive Frames

Receive

Statistics

Receive Multicast Frames

Receive total Bytes

The frames received over the Ethernet port.

The multicast frames received over the Ethernet port.

The total bytes received over the Ethernet port.

TD-W8961ND

300Mbps Wireless N ADSL2+ Modem Router User Guide

Receive CRC Errors

The CRC errors occurred over the Ethernet port when

data is being received.

Receive Under-size Frames

 Select ADSL, and you will see the statistics table as below.

The Under-size frames received over the Ethernet

port.

Statistics Table:

Transmit

Statistics

Receive

Statistics

Transmit total PDUs

Transmit total Error Counts

Receive total PDUs

Receive total Error Counts

The total PDUs transmitted over the ADSL port.

The total errors occurred over the ADSL port when data

is being transmitted.

The total PDUs transmitted over the ADSL port.

The total errors occurred over the ADSL port when data

is being received.

 Select WLAN, and you will see the statistics table as below.

Statistics Table:

The frames transmitted over the WLAN when wireless data is

being transmitted.

The errors occurred over the WLAN when wireless data is being

transmitted.

The drops occurred over the WLAN when wireless data is being

transmitted.

The frames received over the WLAN when wireless data is being

transmitted.

The errors occurred over the WLAN when wireless data is being

received.

The drops occurred over the WLAN when wireless data is being

received.

Transmit

Statistics

Receive

Statistics

Tx Frames Count

Tx Errors Count

Tx Drops Count

Rx Frames Count

Rx Errors Count

Rx Drops Count

Click the REFRESH button to refresh immediately.

+ 58 hidden pages