TP-Link TD-8840B User Manual
TD-8840 User Guide
ADSL2+ Modem Router
Rev: 2.0.1
1910010192
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark of
TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or
registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from TP-LINK
TECHNOLOGIES CO., LTD. Copyright © 2009 TP-LINK TECHNOLOGIES CO., LTD.
All rights reserved.
http://www.tp-link.com
I
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
II
EC DECLARATION OF CONFORMITY (EUROPE)
In compliance with the EMC Directive 89/336/EEC, Low Voltage Directive 73/23/EEC, this product
meets the requirements of the following standards:
• EN55022
• EN55024
• EN60950
SAFETY NOTICES
Caution:
Do not use this product near water, for example, in a wet basement or near a swimming pool.
III
CONTENTS
Package Contents....................................................................................................1
Chapter 1. Introduction ........................................................................................ 2
1.1 Product Overview...................................................................................................... 2
1.2 Main Features........................................................................................................... 2
1.3 Supporting Protocol................................................................................................... 3
1.4 Transmit Data-rate.................................................................................................... 3
1.5 ATM Property............................................................................................................ 3
1.6 System Support......................................................................................................... 4
1.7 Working Environment................................................................................................ 4
1.8 Conventions.............................................................................................................. 2
Chapter 2. Hardware Installation Guide.............................................................. 5
2.1 System Requirement................................................................................................. 5
2.2 The Front Panel ........................................................................................................ 5
2.3 The Rear Panel......................................................................................................... 6
2.4 Environment Requirements....................................................................................... 6
2.5 Hardware Installation Procedures............................................................................. 6
Chapter 3. Quick Installation Guide ....................................................................8
3.1 Configure PC............................................................................................................. 8
3.2 Login ....................................................................................................................... 12
3.3 Quick Setup............................................................................................................. 13
3.3.1 PPPoA............................................................................................................................14
3.3.2 PPPoE............................................................................................................................15
3.3.3 MER................................................................................................................................17
3.3.4 IPoA................................................................................................................................18
3.3.5 Bridging ..........................................................................................................................19
Chapter 4. Software Configuration....................................................................21
4.1 Device Info.............................................................................................................. 21
4.2 Quick Setup............................................................................................................. 21
4.3 Advanced Setup...................................................................................................... 21
4.3.1 WAN...............................................................................................................................22
4.3.2 LAN.................................................................................................................................33
4.3.3 MAC Clone.....................................................................................................................36
4.3.4 Security...........................................................................................................................37
4.3.5 Routing...........................................................................................................................40
IV
4.3.6 DSL.................................................................................................................................42
4.4 Diagnostics.............................................................................................................. 44
4.5 Management........................................................................................................... 45
4.5.1 Settings...........................................................................................................................45
4.5.2 System Log ....................................................................................................................47
4.5.3 SNMP Agent...................................................................................................................48
4.5.4 Access Control...............................................................................................................49
4.5.5 Update Firmware............................................................................................................51
4.5.6 Save/Reboot...................................................................................................................52
Chapter 5. Software Dial..................................................................................... 53
Appendix A: FAQ....................................................................................................55
Appendix B: Default Configuration.......................................................................57
V
TD-8840 ADSL2+ Modem Router User Guide
1
Package Contents
The following items should be found in your package:
¾ One TD-8840 ADSL2+ Modem Router
¾ One AC power Adapter for TD-8840 ADSL2+ Modem Router
¾ One Resource CD for TD-8840 ADSL2+ Modem Router, including:
• This Guide
• Other Helpful Information
• Quick installation Guide Program
¾ Quick installation Guide
¾ One RJ45 cable
¾ Two RJ11 cables
¾ One ADSL splitter
)
Note:
Make sure that the package contains the above items. If any of the listed items are damaged or
missing, please contact with your distributor.
TD-8840 ADSL2+ Modem Router User Guide
2
Chapter 1. Introduction
Thank you for choosing the TD-8840 ADSL2+ Modem Router.
1.1 Product Overview
With the excellent circuit design and high quality production, we guarantee the ADSL2+ Modem
Router’s high performance, great stability and easy to use.
The TD-8840 uses integrated ADSL2+ transceiver. The AFE supports full-rate ADSL connectivity
conforming to the ITU and ANSI specifications.
In addition to the basic DMT physical layer functions, the ADSL PHY supports dual latency ADSL
framing (fast and interleaved) and the I.432 ATM Physical Layer.
The TD-8840 is a complete plug-and-play solution. With standard Ethernet interface, it can be
directly connected to any 10M/100M Ethernet devices, and support Auto-MDIX.
The TD-8840 uses not only html (web mode through Ethernet port) but also external utility
software to configure the Router. You can download it from our website (http://www.tp-link.com).
1.2 Conventions
The Router or TD-8840, or device mentioned in this User guide stands for TD-8840 ADSL2+
Modem Router without any explanations.
Parameters provided in the pictures are just references for setting up the product, which may
differ from the actual situation.
You can set the parameters according to your demand.
)
Note:
The two devices of TD-8840 and TD-8840B are sharing this User Guide. For simplicity, we will
take TD-8840 for example throughout this Guide.
1.3 Main Features
¾ High speed and asymmetry data transmit mode, built-in 4-port switch realize multi-user to
share wide-band internet access
¾ Supports All ADSL2+ industrial standards
¾ Compatible with all mainstream DSLAM (CO)
¾ Firmware upgradeable
¾ Provides integrated access of internet and route function which face to SOHO user
TD-8840 ADSL2+ Modem Router User Guide
3
¾ Advanced DMT modulation and demodulation
¾ Real-time Configuration and device monitoring
¾ Quick response semi-conductive surge protect circuit, provides reliable ESD and
surge-protect function
1.4 Supporting Protocol
- G.992.1 (G.dmt) - Annex A/B/C
- G.992.2 (G.lite) - Annex A/B/C
- ANSI T1.413
- G.992.3 (ADSL2) - Annex A/B/C/M and Annex L (RE-DSL) compliant
- G.992.5 (ADSL2+) Annex A/B/C and Annex L (RE-DSL) compliant
- ADSL dual latency (fast path and interleaved path)
- I.432 ATM physical layer compliant
- Supports RFC2364 (PPPoA)
- Supports RFC2516 (PPPoE)
- Supports RFC1483 (EoA) (Bridged *and Router)
- Supports RFC1577 (IPoA)
)
Note:
“*” Needs the third-party software.
1.5 Transmit Data-rate
¾ Max download data-rate: 24Mbps
¾ Max upload data-rate: 3.5Mbps
¾ Max line length: 6Km
1.6 ATM Property
¾ AAL0, AAL5, OAM, RM, and raw cell types supported
¾ Direct hardware support for 4 Receive VCs, with additional RX VCs and TX VCs supported in
software
¾ Full 24-bit Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI)
TD-8840 ADSL2+ Modem Router User Guide
4
1.7 System Support
¾ Support PVC
¾ Support NAT、DHCP and so on
¾ Support IEEE 802.3、IEEE 802.3u
¾ Support 10Base-T/100BASE-TX full-duplex or half duplex Ethernet
¾ Support Auto-MDIX
1.8 Working Environment
¾ Operating temperature: 0 ~40 ℃℃
¾ Storage temperature: -40 ~70 ℃℃
¾ Working Humidity: 10%~90% RH (non-condensing)
¾ Storage Humidity: 5%~90% RH (non-condensing)
TD-8840 ADSL2+ Modem Router User Guide
5
Chapter 2. Hardware Installation Guide
The TD-8840 maintains five separate interfaces: four Ethernet and one ADSL interface. The
Router should not be located where it will be exposed to moisture or excessive heat. Place the
Router in a location where it can be safely connected to the various devices. The electrical outlet
shall be installed near the device and shall be easily accessible.
2.1 System Requirement
Confirm your computer has been installed with networking interface card (NIC) before connecting
ADSL2+ Modem Router to your computer, with the operating system supporting the TCP/IP
protocol.
2.2 The Front Panel
The front panel of ADSL2+ Modem Router includes one power indicator and seven function
indicators, as explained in chart below.
LED Explanation
Name
Status
Indication
On Power is on.
Power
Off Power is off.
On The LINE port is linked up.
Flash The ADSL negotiation is in progress.
ADSL
Off The LINE port is linked down.
On A successful PPP connection has been built.
Flash Data is being transferred over the Internet.
Internet
Off
There is no successful PPP connection or the Router works on
Bridge mode.
On
There is a successful connection on the corresponding 1~4 (LAN)
port but no activity.
Off
There is no connection on the corresponding 1~4 (LAN) port or the
connection is abnormal.
1~4 (LAN)
Flash Data is being transferred over the 1~4 (LAN) port.
TD-8840 ADSL2+ Modem Router User Guide
6
2.3 The Rear Panel
¾ ON/OFF: Turn on/off the ADSL2+ Modem Router’s power.
¾ POWER: Please do not use any unknown power adapter; otherwise your ADSL2+ Modem
Router may be damaged.
¾ RESET (reset default): With the Router powered on, use a pin to press and hold the Reset
button for at least 5 seconds. And then release the button and wait the Router to reboot to its
factory default settings.
¾ 1~4(LAN): Connect with your computer’s NIC.
¾ LINE (WAN): Connect to the MODEM Port of Splitter or connect to the telephone line port.
2.4 Environment Requirements
¾ Place your Router on the flat and stable platform.
¾ Place your Router in a well ventilated place far from direct sunlight, any heater or heating
vent.
¾ Leave at least 2 inches (5cm) space around the device for heat dissipation.
¾ Keep your Router away from appliances with a strong electric field or magnetic field, such as
a microwave oven or refrigerator.
¾ Turn off your Router and unplug the power adapter in a lighting storm to avoid damage.
¾ The electrical outlet shall be installed near the device and shall be easily accessible.
2.5 Hardware Installation Procedures
Before connecting the Router to your computer, make sure your broadband service provided by
your ISP is available. Cut off the power supply and keep your hands dry. The procedure to
connect the Router can be described in the following steps.
First Step: Connect the MODEM port of Splitter with the TD-8840 ADSL2+ Modem Router’s LINE
port by telephone line. If you need to use a telephone, please attach telephone line into the phone
port of Splitter.
Second Step: Connect category 5 cable with RJ45 jacks to the Router’s LAN port and your
computer’s NIC.
TD-8840 ADSL2+ Modem Router User Guide
7
Third Step: Plug one end of the AC Power Adapter into the Power jack on the Router and the
other end to a standard electrical outlet.
Last Step: Check the line connection to see if everything is ready. Power up finally.
Figure 2-1
TD-8840 ADSL2+ Modem Router User Guide
8
Chapter 3. Quick Installation Guide
3.1 Configure PC
After you directly connect your PC to the TD-8840 or connect your adapter to a Hub/Switch which
has connected to the Router, you need to configure your PC’s IP address. Now you have two
ways to configure the TCP/IP protocol below:
¾ Setting IP address automatically
Step 1: Click the Start menu on your desktop, right click My Network Places, and then select
Properties (shown in Figure 3-1).
Figure 3-1
Step 2: Right click Local Area Connection (LAN), and then select Properties.
TD-8840 ADSL2+ Modem Router User Guide
9
Figure 3-2
Step 3: Select General tab, highlight Internet Protocol (TCP/IP), and then click the Properties
button.
Figure 3-3
Step 4: Select “Obtain an IP address automatically” and “Obtain DNS server address
automatically” in the screen below. And then click OK.
TD-8840 ADSL2+ Modem Router User Guide
10
Figure 3-4
¾ Setting IP address manually
The default IP address of the ADSL2+ Modem Router is 192.168.1.1, and the default Subnet
Mask is 255.255.255.0. These values can be seen from the LAN, and can be changed as your
desire. As an example, we use the default values for description in this guide.
Step 1: Select Use the following IP address radio button in the next screen.
Step 2: Enter the IP address as 192.168.1.* (* is any value between 2 to 254). The Subnet
mask is 255.255.255.0. Then type the ADSL Router’s LAN IP address 192.168.1.1 into
the Default gateway field.
Step 3: Select Use the following DNS server addresses radio button. In the Preferred DNS
Server field you can enter the same value as the Default gateway or type the local DNS
server IP address.
TD-8840 ADSL2+ Modem Router User Guide
11
Figure 3-5
)
Note:
1) Users of Windows 98 can open TCP/IP Properties according to the following: Right-click
(Mouse) Network Neighbor Æ Choose Properties -Æ Double-click TCP/IP.
2) Users of Windows 2000/NT/XP can do the following: Right-click Network Neighbor Æ
Choose Properties Æ Right-click Local Connection Æ Choose Properties Æ Double-click
Internet Protocol (TCP/IP).
3) The words in fact may be different with this guide.
Now, you can run the Ping command in the command prompt to verify the network connection.
Please click the Start menu on your desktop, select Run tab, type cmd in the field, and then type
ping 192.168.1.1 on the next screen, and then press Enter.
If the screen looks like the following, you have been successful.
TD-8840 ADSL2+ Modem Router User Guide
12
Figure 3-6
If the screen looks like the following, the connection has failed. Please try again.
Figure 3-7
3.2 Login
Open your web browser and enter http://192.168.1.1 in the address bar of the browser. When
ADSL connection is OK, the following login box will pop up. Enter default user name (admin) and
password (admin) as shown in Figure 3-8. Click OK to enter the Web-based Utility of the Router.
Figure 3-8
TD-8840 ADSL2+ Modem Router User Guide
13
3.3 Quick Setup
Figure 3-9 is the main page of the Router.
Figure 3-9
Please select Quick Setup. Enter the VPI and VCI values provided by your ISP and click Next.
Figure 3-10
Select the relevant Connection Type and Encapsulation Mode provided by your ISP and click
Next.
Loading...