TP-Link TD-8817 User Manual
TD-8817
ADSL2/2+ Ethernet/USB Router
Rev：1.0.0
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark of
TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or
registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from TP-LINK
TECHNOLOGIES CO., LTD. Copyright © 2007 TP-LINK TECHNOLOGIES CO., LTD. All rights
reserved.
http://www.tp-link.com
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarant ee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
Package contents
The following contents should be found in your box:
¾ One TD-8817 ADSL2/2+ Ethernet/USB Router
¾ One AC power Adapter for TD-8817 ADSL2/2+ Ethernet/USB Router
¾ Quick Installation Guide
¾ One RJ45 cable
¾ One USB cable
¾ Two RJ11 cables
¾ One ADSL splitter (only for Annex A)
¾ One Resource CD , including:
z This User Guide
z USB Driver
z Other Helpful Information
Note:
)
If any of the listed contents are damaged or missing, please contact the retailer from whom you
purchased the product for assistance.
CONTENT
Chapter 1. Introduction ........................................................................................1
1.1 Product Overview...................................................................................................... 1
1.2 Main Features ........................................................................................................... 1
1.3 Conventions .............................................................................................................. 2
Chapter 2. Hardware Installation......................................................................... 3
2.1 The Front Panel ........................................................................................................ 3
2.2 The Back Panel......................................................................................................... 3
2.3 Installation Environment............................................................................................ 4
2.4 Hardware installation procedures.............................................................................. 4
Chapter 3. Quick Installation Guide .................................................................... 6
3.1 Configure PC............................................................................................................. 6
3.2 USB Configuration .................................................................................................... 9
3.3 Login ....................................................................................................................... 11
Chapter 4. Software Configuration....................................................................15
4.1 Status...................................................................................................................... 15
4.2 Quick Start .............................................................................................................. 16
4.3 Interface Setup........................................................................................................ 16
4.3.1 Internet ...........................................................................................................................17
4.3.2 LAN.................................................................................................................................21
4.4 Advanced Setup...................................................................................................... 24
4.4.1 Firewall...........................................................................................................................24
4.4.2 Routing...........................................................................................................................24
4.4.3 NAT ................................................................................................................................25
4.4.4 QoS ................................................................................................................................29
4.4.5 VLAN..............................................................................................................................31
4.4.6 ADSL..............................................................................................................................33
4.5 Access Management............................................................................................... 34
4.5.1 ACL.................................................................................................................................34
4.5.2 Filter................................................................................................................................35
4.5.3 SNMP.............................................................................................................................43
4.5.4 UPnP..............................................................................................................................43
4.5.5 DDNS .............................................................................................................................44
4.5.6 CWMP............................................................................................................................44
4.6 Maintenance............................................................................................................ 45
4.6.1 Administration.................................................................................................................45
4.6.2 Time Zone......................................................................................................................46
4.6.3 Firmware.........................................................................................................................47
4.6.4 System Restart...............................................................................................................49
4.6.5 Diagnostic.......................................................................................................................50
4.7 Help......................................................................................................................... 50
Appendix A: Specification.....................................................................................52
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide
Chapter 1. Introduction
1.1 Product Overview
Thank you for choosing the TD-8817 ADSL2/2+ Ethernet/USB Router. The device is designed to
provide a simple and cost-effective ADSL Internet connection for a private Ethernet network.
TD-8817 connects to an Ethernet LAN or computers via standard Ethernet ports. The ADSL
connection is made using ordinary telephone line with standard connectors. Multiple workstations
can be networked and connected to the Internet using a single Wide Area Network (WAN)
interface and single global IP address. The advanced security enhancements, IP/MAC Filter,
Application Filter and URL Filter can help to protect your network from potentially devastating
intrusions by malicious agents from the outside of your network.
Quick Start of the Web-based Utility is supplied and friendly help messages are provided for the
configuration. Network and Router management is done through the Web-based Utility which can
be accessed through local Ethernet using any web browser.
ADSL
TD-88 1 7 supports full-rate ADSL2+ connectivity conforming to the ITU and ANSI specifications. In
addition to the basic DMT physical layer functions, the ADSL2+ PHY supports dual latency
ADSL2+ framing (fast and interleaved) and the I.432 ATM Physical Layer.
1.2 Main Features
¾ One 10/100M RJ-45 LAN ports (Auto MDI/MDIX), one RJ11 port, one USB 1.1 port.
¾ Supports downstream transmission rates of up to 24Mbps and upstream transmission rates
of 1Mbps.
¾ Supports long transfers, the max line length can reach to 6.5Km.
¾ Supports remote configuration and management through SNMP
¾ Supports PPPoE, it allows connecting the internet on demand and disconnecting from the
Internet when idle.
¾ Quick response semi-conductive surge protection circuit, provides reliable ESD and
surge-protect function.
¾ High speed and asymmetrical data transmit mode, provides safe and exclusive bandwidth.
and CWMP.
¾ Supports All ADSL industrial standards.
¾ Compatible with all mainstream DSLAM (CO).
¾ Provides integrated access of internet and route function which face to SOHO user.
¾ Real-time Configuration and device monitoring.
¾ Supports Multiple PVC (Permanent Virtual Circuit).
¾ Built-in DHCP server.
1
¾ Built-in firewall, supports IP/MAC filter, Application filter and URL filter.
¾ Supports Virtual Server, DMZ host and IP Address Mapping.
¾ Supports Dynamic DNS, UPnP and Static Routing.
¾ Supports system log and flow Statistics.
¾ Supports firmware upgrade and Web management.
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide
1.3 Conventions
The Router or device mentioned in this User guide stands for TD-8817 without any explanations.
Parameters provided in the pictures are just references for setting up the product, which may
differ from the actual situation.
2
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide
Chapter 2. Hardware Installation
2.1 The Front Panel
Figure 2-1
The LEDs are located on the front panel, they indicate the device’s working status. For details,
please refer to LED Explanation.
LED Explanation:
Indicator Description Status Function Details
On
USB USB status
LAN Ethernet
ADSL
ADSL
status
Act Data
Power Power
Off
Flash
On
Off
Flash
Slow flash
Quick flash
On
Flash
Off
On
Off
2.2 The Back Panel
Connection to telecom network is OK
Connection on USB port is abnormal
Data is transmitting or receiving
Connection to telecom network is OK
Connection on LAN port abnormal
Data is transmitting or receiving
Self-detecting when power up
Connecting to the telecom network
Connection to telecom network is OK
There is data transmitting or receiving
on WAN port
No data transmitting or receiving on
WAN port
Power OK
Power fail
Figure 2-2
¾ On/OFF: The switch for the power.
¾ POWER: The Power plug is where you will connect the power adapter.
¾ RESET: There are two ways to reset the Router's factory defaults.
Method one: When the device is working, please press the reset button of the Router, keep
the reset button pressed down for more than five seconds.
3
Method two：Restore the default setting from “Maintenance-SysRestart” of the Router's
Web-based Utility.
¾ LAN: Through the port, you can connect the Router to your PC or the other Ethernet network
devices.
¾ USB: Connect with your computer’s USB interface
¾ LINE: Through the port, you can connect the Router with the telephone.
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide
2.3 Installation Environment
¾ The Product should not be located where it will be exposed to moisture or excessive heat.
¾ Place the Router in a location where it can be connected to the various devices as well as to
a power source.
¾ Make sure the cables and power cord are placed safely out of the way so they do not create a
tripping hazard.
¾ The Router can be placed on a shelf or desktop.
2.4 Hardware installation procedures
The procedure to install the Router can be described in the following steps:
First Step: Connect the Modem port of Splitter with the LINE port of the Router by telephone line.
Second Step: Connect category 5 cable with RJ45 jacks to Router’s LAN port and your
computer’s NIC. Or connect USB cable to ADSL2+ Router’s USB port and your computer’s USB
interface.
driver first. For the detailed operation please refer to “3.2 USB Configuration” in User Guide.)
Third Step: Plug one end of the provided AC Power Adapter( 9V/ 0.8A ) into the Power jack on
the Router and the other end to a standard electrical outlet( 220V～50/ 60HZ ).
Last Step: Check the line connection to see if everything is ready. Power up finally.
( When you connect your PC to the Router through the USB port, please install the USB
4
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide
Figure 2-3
5
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide
Chapter 3. Quick Installation Guide
3.1 Configure PC
After you directly connect your PC to the TD-8817 or connect your adapter to a Hub/Switch which
has connected to the Router, you need to configure your PC’s IP address. Follow the steps below
to configure it.
Step 1: Click the Start menu on your desktop, right click My Network Places, and then select
Properties (shown in Figure 3-1).
Figure 3-1
Step 2: Right click Local Area Connection (LAN), and then select Properties.
6
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide
Figure 3-2
Step 3: Select General tab, highlight Internet Protocol (TCP/IP), and then click the Properties
button.
Figure 3-3
7
Step 4: Configure the IP address as Figure 3-4 shows. After that, click OK.
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide
Figure 3-4
Note:
)
You can configure the PC to get an IP address automatically, select “Obtain an IP address
automatically” and “Obtain DNS server address automatically” in the screen above.
Now, you can run the Ping command in the command prompt to verify the network connection.
Please click the Start menu on your desktop, select run tab, type cmd or command in the field
and press Enter. To continue, please type ping 192.168.1.1 on the following appeared command
prompt screen and then press Enter.
If the result displayed is similar to the screen below, the connection between your PC and the
Router has been established.
Figure 3-5
8
If the result displayed is similar to the screen shown below, it means that your PC has not
connected to the Router.
You can check it follow the steps below:
1) Is the connection between your PC and the Router correct?
The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should
be lit.
2) Is the TCP/IP configuration for your PC correct?
If the Router's IP address is 192.168.1.1, your PC's IP address must be within the range of
192.168.1.2 ~ 192.168.1.254.
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide
Figure 3-6
3.2 USB Configuration
If you use the USB interface, First, you must install the USB’s driver to the computer. You can
obtain the drivers from the provided CD, or download from our website. (http://www.tp-link.com
USB Drive installation procedures
Step 1: Please connect your PC to the Router through the USB port at first, then open the
relative operating system folder in the CD, and double click Setup.exe to install the USB
driver.
Step 2: Soon, Figure 3-7 will display after a moment. Click Next to continue.
)
9
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide
Figure 3-7
Step 3: You will see Figure 3-8 as follow, please wait a moment.
Figure 3-8
Step 4: After that, you will see Figure 3-9. Click Finish to complete the installation.
10
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide
Figure 3-9
Note:
)
1) All of the above settings are under windows XP.
2) If you want to pull out the USB device you must disconnect the network of USB first.
3) In the Vista operating system, maybe the “Unknown Device” screen will pop up when you
insert the USB cable of the Router to a computer, please just unplug the USB cable and try
again.
3.3 Login
Once your host PC is properly configured, please proceed as follows to use the Web-based Utility:
Start your web browser and type the private IP address of the Router in the URL field: 192.168.1.1.
After that, you will see the screen shown below, enter the default User Name admin and the
default Password admin, and then click OK to access to the Quick Setup screen. You can follow
the steps below to complete the Quick Setup.
11
Step 1: Select the Quick Start tab, then click RUN WIZARD, and you will see Figure 3-11. Click
the NEXT button.
TD-8817 ADSL2/2+ Ethernet/USB Router User Guide
Figure 3-10
Figure 3-11
Step 2: Change the login password in Figure 3-12, and then click the NEXT button.
Figure 3-12
Step 3: Configure the time for the Router, and then click the NEXT button.
12
Loading...