TP-Link TD-8810B, TD-8810 User Manual

TD-8810/TD-8810B User Guide

External ADSL ROUTER

Rev：1.0.1

Specifications are subject to change without notice. is a registered trademark of

TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or

registered trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or used to make any

derivative such as translation, transformation, or adaptation without permission from TP-LINK

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/ TV technician for help.

CE Mark Warning

This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

EC DECLARATION OF CONFORMITY (EUROPE)

In compliance with the EMC Directive 89/336/EEC, Low Voltage Directive 73/23/EEC, this product

meets the requirements of the following standards:

• EN55022

• EN55024

• EN60950

SAFETY NOTICES

Caution:

Do not use this product near water, for example, in a wet basement or near a swimming pool.

III

Package contents

The following contents should be found in your box:

¾ One TD-8810/TD-8810B External ADSL ROUTER

¾ One AC power Adapter for TD-8810 External ADSL ROUTER

¾ One Resource CD for TD-8810 External ADSL ROUTER, including:

• This Guide

• Quick installation Guide Program

• Other Helpful Information

¾ Quick installation Guide

¾ One RJ45 cable

¾ Two RJ11 cable

¾ One ADSL splitter (Only for TD-8810)

Note:

)

If any of the listed contents are damaged or missing, please contact the retailer from whom you purchased the product for assistance.

COMMENT

Chapter 1. Introduction ........................................................................................ 1

1.1 Product Overview ...................................................................................................... 1

1.2 Main Features ........................................................................................................... 1

1.3 Supporting protocol ................................................................................................... 1

1.4 Transmit data-rate ..................................................................................................... 2

1.5 ATM propert .............................................................................................................. 2

1.6 System support ......................................................................................................... 2

1.7 Working environment ................................................................................................ 2

1.8 Electric parameter ..................................................................................................... 3

1.9 Conventions .............................................................................................................. 3

Chapter 2. Hardware Installation ......................................................................... 4

2.1 System requirement .................................................................................................. 4

2.1.1 LED explanation ............................................................................................................... 4

2.2 Rear-panel ................................................................................................................ 4

2.3 Hardware installation procedures.............................................................................. 5

Chapter 3. System Configuration ........................................................................ 6

3.1 Computer Configuration ............................................................................................ 6

3.2 Login ......................................................................................................................... 7

3.3 Web Setup ................................................................................................................ 9

3.3.1 DHCP IP Reservation..................................................................................................... 20

3.3.2 DNS................................................................................................................................22

3.4 Software Dial ........................................................................................................... 25

Chapter 4. Advantage management setup ....................................................... 26

Appendix A: FAQ.................................................................................................... 27

Appendix B: Default Config................................................................................... 29

Appendix C: Contact Information ......................................................................... 30

TD-8810 External ADSL Router User Guide

Chapter 1. Introduction

1.1 Product Overview

TP-LINK® TD-8810/TD-8810B External ADSL ROUTER is the latest product designed and

manufactured by TP-LINK TECHNOLOGIES CO., LTD. With TP-LINK’s excellent circuit design

and high quality production, we guarantee the ADSL ROUTER’s high performance, great stability

and easy to use.

The TD-8810/TD-8810B uses integrated ADSL transceiver. The AFE supports full-rate ADSL

connectivity conforming to the ITU and ANSI specifications.

In addition to the basic DMT physical layer functions, the ADSL PHY supports dual latency ADSL

framing (fast and interleaved) and the I.432 ATM Physical Layer.

The TD-8810/TD-8810B is a complete plug-and-play solution. With standard Ethernet interface, it

can be directly connected to any 10M/100M Ethernet devices, support Auto-MDIX.

The TD-8810/TD-8810B not only uses html (web mode through Ethernet port) to configure the

ROUTER but also uses external utility software. You can download it from our website

(http://www.tp-link.com).

1.2 Main Features

¾ High speed and asymmetry data transmit mode, provides safe and exclusive bandwidth

¾ Support All ADSL industrial standards

¾ Compatible with all mainstream DSLAM (CO)

¾ Firmware upgradeable

¾ Provide integrated access of internet and route function which face to SOHO user

¾ Advanced DMT modulation and demodulation

¾ Real-time Configuration and device monitoring

¾ Quick response semi-conductive surge protect circuit, provides reliable ESD and

surge-protect function

1.3 Supporting protocol

- G.992.1 (G.dmt) - Annex A ( TD-8810)/Annex B(TD-8810B)

- G.992.2 (G.lite) - Annex A( TD-8810)/Annex B(TD-8810B)

- ANSI T1.413

- G.992.3 (ADSL2) - Annex A( TD-8810)/Annex B(TD-8810B) and Annex M

- G.992.5 (ADSL2+) - Annex A( TD-8810)/Annex B(TD-8810B) and Annex M

- ADSL dual latency (fast path and interleaved path)

TD-8810 External ADSL Router User Guide

- I.432 ATM physical layer compliant

- Supports RFC2364 (PPPoA)

- Supports RFC2516 (PPPoE)

- Supports RFC2684 (EoA)(Bridged *and Router)

- Supports RFC1577 (IPoA)

Note:

)

“*” Needs the third-party software.

1.4 Transmit data-rate

¾ Max download data-rate: 24Mbps

¾ Max upload data-rate: 1Mbps

¾ Max line length: 6Km

1.5 ATM propert

¾ AAL0, AAL5, OAM, RM, and raw cell types supported

¾ Direct hardware support for 4 Receive VCs, with additional RX VCs and TX VCs supported in

software

¾ Full 24-bit Virtual Path Identifier (VPI) and Virtual Circuit Identifier (VCI)

1.6 System support

¾ Support PVC

¾ Support NAT、DHCP and so on

¾ Support IEEE 802.3、IEEE 802.3u

¾ Support 10Base-T/100BASE-TX full-duplex or half duplex Ethernet

¾ Support Auto-MDIX

1.7 Working environment

¾ Operating temperature: 0 ~40 ℃℃

¾ Storage temperature: -40 ~70 ℃℃

¾ Humidity: 10%~90% (non-condensing)

TD-8810 External ADSL Router User Guide

1.8 Electric parameter

¾ Adaptor power Output: 9VAC/0.8A，50Hz or 60 Hz

¾ Power consumption: 4W Maximum

1.9 Conventions

The Router or TD-8810/TD-8810B, or device mentioned in this User guide stands for

TD-8810/TD-8810B External ADSL ROUTER without any explanations.

Parameters provided in the pictures are just references for setting up the product, which may

differ from the actual situation.

You can set the parameters according to your demand.

TD-8810 External ADSL Router User Guide

Chapter 2. Hardware Installation

The TD-8810/TD-8810B maintains three separate interfaces, one Ethernet, one ADSL and one

power adapter inerface.

The Router should not be located where it will be exposed to moisture or excessive heat.

Place the Router in a location where it can be safely connected to the various devices as well as

to a power source.

2.1 System requirement

Confirm your computer has been installed with networking interface card (NIC) before connecting

ADSL ROUTER to your computer, with operating system supporting the TCP/IP protocol.

2.1.1 LED explanation

The front panel of ADSL ROUTER includes one power indicator (RED) and seven function

indicators (GREEN), as explained in chart below:

Indicator Description Status Function Details

PWR Power

ADSL ADSL status

ALARM Mistake

ACT Data

LAN Ethernet

On Power OK

Off Power fail

Slow flash Self-detecting when power up

Quick flash Connecting to the telecom network

On Connection to telecom network OK

There is mistake when ADSL transmitting data

or receiving data

Off ADSL normal

There is data transmitting or receiving on WAN

port

Off No data transmitting or receiving on WAN port

On LAN port normal

Off Connection on LAN port abnormal

Flash Data transmitting or receiving on LAN port

2.2 Rear-panel

¾ ON/OFF: Turn on/off the ADSL ROUTER’s power.

¾ Power (9VAC/0.8A input): Please do not use any unknown power adaptor, otherwise your

ADSL ROUTER may be damaged.

¾ RESET(reset default): First press the reset button of ROUTER, then turn on the ROUTER’s

TD-8810 External ADSL Router User Guide

power for at least three seconds. It will resume the default manufacturer’s setup.

¾ LAN: Connect with your computer’s NIC.

¾ LINE(WAN): Connect to the MODEM Port of Splitter or Connecting the telephone line.

2.3 Hardware installation procedures

The procedure to install the Router can be described in general terms in the following steps:

First Step: Connect the MODEM port of Splitter with the TD-8810/TD-8810B ADSL ROUTER

LINE port by telephone line. While you need to use a telephone, please attach telephone line into

the phone of Splitter.

Second Step: Connect category 5 cable with RJ45 jacks to the ADSL ROUTER’s LAN port and

your computer’s NIC.

Third Step: Plug one end of the AC Power Adapter into the Power jack on the Ethernet ADSL

ROUTER and the other end to a standard electrical outlet.

Last Step: Check the line connection to see if everything is ready. Power up finally.

Figure 2-1

TD-8810 External ADSL Router User Guide

Chapter 3. System Configuration

3.1 Computer Configuration

1. Connect the cable according to Chapter 2, turn on the power.

2. Change the IP address of your PC（Figure 3-1）: Open TCP/IP Properties of the LAN card in

your PC, enter the IP address as 192.168.1.*.

Note:

)

(* is any value between 2 to 254, Net mask is 255.255.255.0, Gateway is 192.168.1.1, DNS address is the value provided by ISP).

Figure 3-1

Note:

)

Users of Windows 98 can open TCP/IP Properties according to the following: Right-click (Mouse)

Network Neighbor -> Choose Properties -> Double-click TCP/IP.

Users of Windows 2000/NT/XP can do the following: Right-click Network Neighbor -> Choose

Properties -> Right-click Local Connection -> Choose Properties -> Double-click Internet

Protocol (TCP/IP).

)

Note:

+ 24 hidden pages