TP-Link MiniGBIC Installation Manual

Installation Guide

MiniGBIC Module

Install the SFP

1.Wear an ESD-preventive wrist or ankle strap to prevent ESD damage to the transceiver.

2.Insert the SFP into the SFP slot and firmly press it into place.

3. Remove the protective dust plug from the SFP.

4.Plug fiber-optic cables into the SFP. Note that the SFP works without any additional configuration.

To ask questions, find answers, and communicate with TP-Link

users or engineers, please visit https://community.tp-link.com to join TP-Link Community.

For technical support and other information, please visit https://www.tp-link.com/support, or simply scan the QR code.

If you have any suggestions or needs on the product guides, welcome to email [e-mail].

Remove the SFP

1.Wear an ESD-preventive wrist or ankle strap to prevent ESD damage to the transceiver.

2.Disconnect the network fiber-optic cables from the SFP.

3.Pull the safety latch downwards to release the SFP, and then pull it out from the slot.

4.Reinstall the protective dust plug in the SFP’s optical bores and place it on antistatic mat or a static shielding bag.

<![if ! IE]>

<![endif]>0.0.REV4 7106508733 Link-TP ©2020

Note:

1. Do not touch the output pins on the transceiver with your hand.

2. Always keep the protective dust plug on the SFP’s optical bores until you are ready to make a connection.

Caution:

DO NOT point or stare directly into the beam or into the optical port of the transceiver when it is operating, as this can injure your eyesight.

Connection

Only use the same transceiver model between switches for fast and reliable connectivity.

Switch	Switch
TL-SM311LS	TL-SM311LS
	Fiber

Specifications

General Specifications

Normal	TL-SM311LS
Wave Length	1310 nm
Standards and Protocols	IEEE 802.3z, TCP/IP
Cable	Single-mode Fiber
Fiber Type	9/125 um Single-mode
Max. Cable Length	20 km
Data Rate	1.25 Gbps
Port Type	LC Duplex
Power Support	3.3 V

Environmental and Physical Specifications

Product Operating Temperature	0˚C to 70˚C (32˚F to 158˚F)
Storage Temperature	-40˚C to 85˚C (-40˚F to 185˚F)
Operating Humidity	10% to 90% RH, Non-condensing
Storage Humidity	5% to 90% RH, Non-condensing

TP-Link Compatible Products

	Safety & Emission	FCC, CE		TP-Link Switches with gigabit SFP Slots
	DDM	Yes
				MC220L
	SFP-MSA	Yes
				Note:
	Hot Swappable	Yes		The SFP modules may be incompatible with other vendors’ devices. We
				recommend that you use only TP-Link SFP modules on your TP-Link devices.

FCC compliance information statement

Product Name: MiniGBIC Module

Model Number: TL-SM311LS Responsible party:

TP-Link USA Corporation, d/b/a TP-Link North America, Inc. Address: 145 South State College Blvd. Suite 400, Brea, CA 92821 Website: https://www.tp-link.com/us/

Tel: [phone]

Fax: [phone] E-mail: [e-mail]

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1)This device may not cause harmful interference.

2)This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

We, TP-Link USA Corporation, has determined that the equipment shown as above has been shown to comply with the applicable technical standards, FCC part 15. There is no unauthorized change is made in the equipment and the equipment is properly maintained and operated.

Issue Date: 2020/03/20

BSMI Notice

些適當的對策。

	Pb	Cd	Hg	Cr+6	PBB	PBDE
PCB	○	○	○	○	○	○
	○	○	○	○	○	○
"○"

Industry Canada Statement

CAN ICES-3 (A)/NMB-3(A)

A VCCI-A

EU Declaration of Conformity

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU, 2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.

The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce

Safety Information

Keep the device away from water, fire, humidity or hot environments.

Do not attempt to disassemble, repair, or modify the device.

Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning. Do not point or stare directly into the beam or into the optical port of the transceiver when it is operating, as this can injure your eyesight.

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.

CE Mark Warning

This is a class A product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.

Explanation of the symbols on the product label

Note: The product label can be found at the bottom of the product.

RECYCLING

This product bears the selective sorting symbol for Waste electrical and electronic equipment (WEEE). This means that this product must be handled pursuant to European directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the environment.

Userhasthechoicetogivehisproducttoacompetentrecyclingorganizationortotheretailerwhen he buys a new electrical or electronic equipment.