TP-Link MC220L, MC210CS, MC200CM Installation Guide

Enlarge Your Ethernet Network

Gigabit Ethernet Media Converter

MC200CM/ MC210CS/ MC220L

http://www.tp-link.com/support, or simply scan the QR code.

Package Contents: Media Converter, Power Adapter, User Guide

Note: MC200CM is used as an example throughout this guide. Other models may dier in appearance.

Scenario 1: Connect Devices with and without Optical Interfaces

For technical support and other information, please visit

Ethernet device

with optical interfaces

1000Base-SX interface

LC-SC Fiber Cable

Note: MC220L needs to be plugged in with an SFP module to work normally. It is recommended to use a TP-Link SFP module on MC220L, because other vendors’

SFP modules may be incompatible.

Media Converter

Ethernet device

without optical interfaces

Gigabit Ethernet interface

Twisted-Pair Cable

Scenario 2: Connect Devices without Optical Interfaces

Ethernet device

without optical interfaces

Gigabit Ethernet interface

Note:

1. Either two MC200CMs or two MC210CSs can work cooperatively. Two MC220Ls with the same SFP module can work cooperatively.

2. An MC220L can also cooperate with an MC200CM or an MC210CS. However, the mode and wavelength of the SFP module used in MC220L must be the same as the opposite end.

3. Connect the TX port of one converter to the RX port of the other using a ber cable.

Media Converter Media Converter

Gigabit Ethernet interface

Fiber CableTwisted-Pair Cable Twisted-Pair Cable

Ethernet device

without optical interfaces

LED Explanation

PWR

On: Power on.

O: Power o.

Specications

General Specifications

IEEE 802.3, IEEE 802.3i, IEEE 802.3u, IEEE 802.3ab, IEEE802.3zStandards

LED

Interface

Twisted-Pair

PWR, FX Link/Act, TP Link/Act

For MC200CM/MC210CS: SC ber connector, RJ-45 jack For MC220L: SFP port, RJ-45 jack

10Base-T: 2-pair UTP/STP of Cat. 3 or above (≤100m) 100Base-TX: 2-pair UTP/STP of Cat. 5 or above (≤100m) 1000Base-T: 4-pair UTP/STP of Cat. 5e or above (≤100m)

Link/Act

On: There is a valid link for FX Port.

O: There is no valid link for FX Port.

Flashing: FX Port is transmitting or receiving data.

Environmental and Physical Specifications

Operation Temperature 0˚C to 40˚C (32˚F to 104˚F)

Storage Temperature -40˚C to 70˚C (-40˚F to 158˚F)

Operation Humidity 10% to 90%RH non-condensing

Storage Humidity 5% to 90%RH non-condensing

Link/Act

On: There is a valid link for TP Port.

O: There is no valid link for TP Port.

Flashing: TP Port is transmitting or receiving data.

For MC200CM: 62.5/125μm multi-mode ber (≤220m); 50/125μm multi-mode ber (≤550m)

Fiber

For MC210CS: 9/125μm single-mode ber (≤15km)

For MC220L: depends on the used SFP module

For MC200CM: 850nm

Wave Length

For MC210CS: 1310nm For MC220L: depends on the used SFP module

Power

External Power Adapter: 9V/0.6A

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful inter ference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including inter ference that may cause undesired operation.

Any changes or modications not expressly approved by the part y responsible for compliance could void the user’s

authority to operate the equipment.

BSMI Notice

安全諮詢及注意事項請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。注意防潮，請勿將水或其他液體潑灑到本產品上。插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。此為甲類資訊技術設備，于居住環境中使用時，可能會造成射頻擾動，在此種情況下，使用者會被要求採取某些適當的對策。

限用物質含有情況標示聲明書

限用物質及其化學符號

產品元件名稱

PCB

外殼

電源適配器

備考1："○"系指該項限用物質之百分比含量未超出百分比含量基準值。備考2："—" 系指該項限用物質為排除項目。

鉛 Pb

○

—

鎘

○

汞 Hg

○

六價鉻

CrVI

○

多溴聯苯

PBB

○

多

溴二苯醚

PBDE

○

CE Mark Warning

This is a class A product. In a domestic environment, this product may cause radio inter ference, in which case the user

may be required to take adequate measures.

Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України.

Industry Canada Statement

CAN ICES-3 (A)/NMB-3(A)

EU declaration of conformity

TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of

directives 2014/30/EU, 2014/35/EU, 2009/125/EC and 2011/65/EU.

The original EU declaration of conformity may be found at http://www.tp-link.com/en/ce

この装置は、クラスA情報技術装置です。この装置を家庭環境で使用すると電波妨害を引き起こすことがあります。この場合には使用者が適切な対策を講ずるよう要求されることがあります。 VCCI-A

Safety Information

Keep the device away from water, re, humidity or hot environments.

Do not attempt to disassemble, repair, or modify the device. Do not use damaged charger or USB cable to charge the device. Do not use any other chargers than those recommended. Adapter shall be installed near the equipment and shall be easily accessible. Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.

Do not point or stare directly into the beam or into the optical por t of the transceiver when it is operating, as this can injure

your eyesight.