TP-Link MC210CS User Manual
LED Explanation
PWR
On: Power on
Power o
O:
©2020 TP-Link 7106509046 REV 5.0.0
Enlarge Your Ethernet Network
Gigabit Single-Mode Media Converter
Package Contents: Converter, Power Adapter, Installation Guide
Scenario 1: Connect Devices with and without Optical Interfaces
Ethernet Device
with Optical Interfaces
1000BASE-LX
Media Converter
PWR
RXTX
1000BASE-LX
Gigabit Ethernet
Link/Act
On: Valid link
Flashing: Transmitting or receiving data
O: Invalid link
Ethernet Device
without Optical Interfaces
Gigabit Ethernet
LC-SC/UPC Fiber Cable
Twisted-Pair Cable
Scenario 2: Connect Devices without Optical Interfaces
Ethernet Device
without Optical Interfaces
Gigabit Ethernet Gigabit Ethernet
Note: Connect the TX port of one converter to the RX port of the other using a ber cable.
Media Converter Media Converter
Gigabit Ethernet
1000BASE-LX
RXTX
PWR
Fiber CableTwisted-Pair Cable Twisted-Pair Cable
Specications
General Specifications
Standards
Twisted-Pair
Fiber
Transmission
Distance
Wave Length
Dimensions 94.5x73x27 mm
IEEE 802.3, IEEE 802.3i, IEEE 802.3u,
IEEE 802.3ab, IEEE 802.3x, IEEE 802.3z
PWR, Link/ActLED
2 SC ber optic; 1 RJ45 jackConnector
100BASE-TX: 2-pair UTP/STP of Cat. 5 or above (≤100 m)
1000BASE-T: 4-pair UTP/STP of Cat. 5e or above (≤100 m)
9/125 μm single-mode ber
≤20 km
1310 nm
External Power Adapter: 9 V/0.6 APower
Ethernet Device
without optical Interfaces
PWR
RXTX
1000BASE-LX
Gigabit Ethernet
Environmental and Physical Specifications
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
To ask questions, find answers, and communicate with TP-Link users or
engineers, please visit https://community.tp-link.com to join TP-Link
Community.
For technical support and other information, please visit
https://www.tp-link.com/support, or simply scan the QR code.
If you have any suggestions or needs on the product guides, welcome
to email techwriter@tp-link.com.cn.
0˚C to 50˚C (32˚F to 122˚F)
-40˚C to 70˚C (-40˚F to 158˚F)
10% to 90% RH non-condensing
5% to 90% RH non-condensing
Safety Information
Keep the device away from water, re, humidity or hot environments.
Do not attempt to disassemble, repair, or modify the device. If you need service, please contact us.
Do not use damaged charger or USB cable to charge the device.
Do not use any other chargers than those recommended.
Adapter shall be installed near the equipment and shall be easily accessible.
Do not point or stare directly into the beam or into the optical port of the transceiver when it is operating, as this can injure your eyesight
Use only power supplies which are provided by manufacturer and in the original packing of this product. If you have any questions, please don't
hesitate to contact us.
The plug on the power supply cord is used as the disconnect device, the socket-outlet shall be easily accessible.
Please read and follow the above safety information when operating the device. We cannot guarantee that no accidents or damage will occur due
to improper use of the device. Please use this product with care and operate at your own risk.
EU declaration of conformity
TP-Link hereby declares that the device is in compliance with the essential requirements and other relevant provisions of directives 2014/30/EU,
2014/35/EU, 2009/125/EC, 2011/65/EU and (EU)2015/863.
The original EU declaration of conformity may be found at https://www.tp-link.com/en/ce.
Loading...