User Guide
MC100CM
MC110CS
Fast Ethernet Media Converter
MC111CS
MC112CS
WDM Fast Ethernet Media Converter
REV2.1.0
7106505160
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice.
is a registered trademark of TP-LINK
TECHNOLOGIES CO., LTD. Other brands and product names are
trademarks or registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by
any means or used to make any derivative such as translation,
transformation, or adaptation without permission from TP-LINK
TECHNOLOGIES CO., LTD. Copyright © 2015 TP-LINK TECHNOLOGIES
CO., LTD. All rights reserved.
http://www.tp-link.com
FCC STATEMENT
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including
interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
CE Mark Warning
This is a class A product. In a domestic environment, this product
may cause radio interference, in which case the user may be
required to take adequate measures.
Продукт сертифіковано згідно с правилами системи УкрСЕПРО
на відповідність вимогам нормативних документів та вимогам,
що передбачені чинними законодавчими актами України.
Safety Information
When product has power button, the power button is one of the
way to shut off the product; When there is no power button, the
only way to completely shut off power is to disconnect the
product or the power adapter from the power source.
Don’t disassemble the product, or make repairs yourself. You
run the risk of electric shock and voiding the limited warranty. If
you need service, please contact us.
Avoid water and wet locations.
安全諮詢及注意事項
●請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產
品。
●清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕
布進行清潔。
●注意防潮,請勿將水或其他液體潑灑到本產品上。
●插槽與開口供通風使用,以確保本產品的操作可靠並防止過熱,請
勿堵塞或覆蓋開口。
●請勿將本產品置放於靠近熱源的地方。除非有正常的通風,否則不
可放在密閉位置中。
●請不要私自打開機殼,不要嘗試自行維修本產品,請由授權的專業
人士進行此項工作。
此為甲類資訊技術設備,于居住環境中使用時,可能會造成射頻擾動,
在此種情況下,使用者會被要求採取某些適當的對策。
This product can be used in the following countries:
AT BG BY CA CZ DE DK EE
ES FI FR GB GR HU IE IT
LT LV MT NL NO PL PT RO
RU SE SK TR UA US
CONTENTS
Package contents ........................................................................... 1
Chapter 1 Introduction ............................................................... 2
1.1 Overview of the Converter .......................................... 2
1.2 Conventions ................................................................ 3
1.3 Features ...................................................................... 3
1.4 Connectors and Network Cables Supported ............... 3
1.5 Appearance Indication ................................................ 4
1.5.1 LED Indicators ............................................... 4
1.5.2 Switch ............................................................ 6
1.5.3 Link Fault Pass Through Function ................. 7
Chapter 2 Installation Guide ...................................................... 9
2.1 Fast Ethernet Media Converter ................................... 9
2.2 WDM Fast Ethernet Media Converter ......................... 9
Chapter 3 Configuration ........................................................... 11
3.1 Installation Procedure ............................................... 12
Appendix: Specifications ............................................................. 13