Toshiba D-VR17KB User Manual

COV_E9GA1FD_EN.fm Page 1 Thursday, March 8, 2007 12:09 PM

Introduction Connections Basic Setup Playback

DVD VIDEO RECORDER / VIDEO CASSETTE RECORDER

D-VR17KB

OWNER’S MANUAL

Recording

OPERATIONS

GUIDE

ON / STANDBY

REC DUBBING

VCR

PROGRAM

VCR/DVD REC

DVD

DVDVCR

Editing

Function Setup

VCR Functions

Others

E9GA0BD_EN.book Page 2 Monday, March 26, 2007 10:14 AM

Introduction

Precautions

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE

WARNING

THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The important note is located on the rear of the cabinet.

Laser Safety

This unit employs a laser. Only a qualified service personnel should remove the cover or attempt to service this unit, due to the possibility of eye injury.

CAUTION: USE OF CONTROLS OR

ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

CAUTION: VISIBLE AND INVISIBLE LASER

RADIATION WHEN OPEN AND INTERLOCK DEFEATED. DO NOT STARE INTO BEAM.

LOCATION: INSIDE, NEAR THE DECK

MECHANISM.

Caution

1. Do not attempt to open the cabinet. There are no

2. Slots and openings in the cabinet at the sides and

3. Keep the unit away from radiators and other heat

4. Avoid use near strong magnetic fields.

5. Do not push objects of any kind into the unit

6. Do not spill liquid on the unit. If liquid is spilled

Power Supply

The power supply is connected and the unit is live when the mains cable is plugged into a 220–240 V , 50 Hz AC outlet. To operate the unit, press

[ ON / STANDBY].

WARNING: LIVE PARTS INSIDE.

DO NOT REMOVE ANY SCREWS.

7. Do not stand the unit vertically. Use the unit in a

8. Before attempting to operate the unit, make sure

9. This product is in Stand-by mode when turned off

10. Do not place any combustible objects on the

11. Before moving the unit, be sure to remove any

12. Disconnect the mains plug to shut off when find

13. The mains plug shall remain readily operable.

14. Read both manual instructions to ensure correct

15. Keep the distances 20 cm around apparatus of

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

parts inside you can service. Refer all servicing to qualified service personnel.

underneath are provided for ventilation. To ensure reliable operation and to protect the unit from overheating, these openings must not be blocked or covered. Avoid installation in enclosed spaces such as bookcases unless suitable ventilation is provided.

sources.

through the cabinet slots or openings as they could touch electrically live parts or short circuit parts resulting in a fire or electric shock.

and enters the unit, consult qualified service personnel.

horizontal (flat) position only.

that the timer recording mode is off.

while the mains cable is connected.

device (candles, etc.).

discs and unplug the mains cable from the AC outlet.

troubles or not in use.

and safe installation and interconnection of the unit in multimedia systems.

ventilation openings.

E9GA0BD_EN.book Page 3 Monday, March 26, 2007 10:14 AM

A NOTE ABOUT RECYCLING

This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations.

This product consists of materials which can be recycled and reused if disassembled by a specialised company. Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.

Make your contribution to the environment!!!

• Exhausted batteries do not belong in the dustbin.

• You can dispose of them at a collection point for exhausted batteries or special waste.

• Contact your council for details.

For Customer Use: Carefully read the Model No. and Serial No. located at the back of the unit and enter the information below. Retain this information for future reference. Model No. _____________________ Serial No. _____________________

Connection to Power

Before Switching on make sure that the voltage of your electricity supply is the same as that indicated on the rating plate.

Mains Cord

This appliance may be fitted with a non-rewireable plug. If it is necessary to change the fuse in a nonrewireable plug the fuse cover must be refitted. If the fuse cover is lost or damaged, the plug must not be used until a replacement available from the appliance manufacturer is obtained. It is important that the colour of the replacement fuse cover corresponds with the rating marking on the base of the plug. If the plug has to be changed because it is not suitable for your socket, or becomes damaged, it should be cut off and an appropriate plug fitted following the wiring instructions below. The plug removed must be disposed of safely as insertion into a 13A socket is likely to cause an electrical hazard. For your own safety read the following instructions carefully before attempting to connect this unit to mains. The wires in this mains lead are coloured in accordance with the following code:

BLUE=NEUTRAL, BROWN=LIVE

Important

As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. No connection is to be made to the earth terminal of the plug. If a 13 Amp (BS 1363) Plug is used, a 3 Amp Fuse must be fitted, or if any other type of Plug is used a 3 or 5 Amp Fuse must be fitted, either in the Plug or Adaptor, or on the Distribution Board.

Mains Supply: 220 - 240V 50 Hz - AC only

Do not make any connection to the larger pin marked with the letter “E” or by the symbol or coloured green or green and yellow.

FUSE

BROWN

BLUE

(Neutral)

OUTER SHEATH OF THE WIRE

(Live)

CORD GRIP

Installation Location

For safety and optimum performance of this unit:

• Install the unit in a horizontal and stable position.

• Do not place anything directly on top of the unit.

• Do not place the unit directly on top of the TV.

• Shield the unit from direct sunlight and keep away from sources of intense heat. Avoid dusty or humid locations. Avoid locations with insufficient ventilation for suitable heat dissipation. Do not block the ventilation holes on the sides of the unit. Avoid locations subject to strong vibration or strong magnetic fields.

Avoid the Hazards of Electrical Shock and Fire

• Do not handle the mains cable with wet hands.

• Do not pull on the mains cable to disconnect it from AC outlet. Grasp it by the plug.

• If, by accident, water is spilled on the unit, unplug the mains cable immediately and take the unit to an authorised service centre for servicing.

Moisture Condensation Warning

Moisture condensation may occur inside the unit when it is moved from a cold place to a warm place, after heating a cold room, or under conditions of high humidity. Do not use the unit for at least 2 hours to allow the inside to dry.

Introduction Connections Basic Setup Playback

Recording

Editing

Function Setup

VCR Functions Others

E9GA0BD_EN.book Page 4 Monday, March 26, 2007 10:14 AM

About Copyright

Unauthorised copying, broadcasting, public performance and lending of discs are prohibited. This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorised by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorised by Macrovision. Reverse engineering or disassembly is prohibited.

Notice for the Progressive Scan Outputs

Consumers should note that not all high definition television sets are fully compatible with this product and may cause artifacts to be displayed in the picture. In case of picture problems with 525 or 625 progressive scan output, it is recommended that the user switch the connection to the ‘standard definition’ output. If there are questions regarding your TV set compatibility with this 525p or 625p DVD recorder, please contact our customer service centre.

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

Declaration of Conformity

This product complies with the requirement of the directives EMC-Directive: 89 / 336 / EEC Low Voltage Directive: 73 / 23 / EEC CE Marking: 93 / 68 / EEC

We declare that the following product:

DVD Video Recorder / Video Cassette Recorder Model D-VR17KB

Trade Name: TOSHIBA is in compliance with following Regulations. EN55013: 2001+A1:2003, EN55020: 2002+A1:2003+A2:2005, EN61000-3-2: 2003+A2:2005, EN61000-3-3: 1995 + A1: 2001 EN60065: 2002 EN60825-1 Edition 1.2: 2001

Maintenance

CLEANING THE UNIT

Use a soft cloth slightly moistened with a mild detergent solution. Do not use solutions containing alcohol, spirits, ammonia or abrasive.

Dolby Digital Recording

Digital Recording enables consumers to

“Dolby record high-quality video with stereo sound on recordable DVD discs. The technology, when utilised instead of PCM recording, also saves recordable disc space, allowing for higher video resolution or extended recording time on each DVD. DVDs created using Dolby Digital Recording will play back on all DVD-Video players.” Note: This is true when the players are compatible with actual recordable DVD discs.

“DTS” and “DTS Digital Out” are registered trademarks of DTS, Inc.

DivX, DivX Certified, and associated logos are trademarks of DivX, Inc. and are used under license.

CLEANING DISCS

If a disc becomes dirty, clean it with a cleaning cloth. Wipe the disc from the centre out. Do not wipe in a circular motion. Do not use solvents such as benzine, thinner, commercially available cleaners, detergent, abrasive cleaning agents or antistatic spray intended for analogue records.

DISC HANDLING

Handle the discs so that fingerprints and dust do not adhere to the disc surfaces. Always store the disc in its protective case when it is not in use.

SERVICING

If the unit becomes inoperative, do not try to correct the problem by yourself. There are no user serviceable parts inside. Turn the unit off, unplug the mains cable, and consult your dealer or an authorised service centre.

CLEANING THE DISC LENS

If the unit does not perform correctly even though you have referred to “Troubleshooting” and the relevant sections in the Owner’s Manual, the laser optical pickup unit may be dirty. Consult your dealer or an authorised service centre for inspection and cleaning of the laser optical pickup unit.

E9GA0BD_EN.book Page 5 Monday, March 26, 2007 10:14 AM

AUTO HEAD CLEANING

• Automatically cleans video heads as you insert or remove a cassette, so you can see a clear picture.

• Playback picture may become blurred or interrupted while the TV programme reception is clear. Dirt accumulated on the video heads after a long period of use, or the usage of rental or worn tapes can cause this problem. If a streaky or snowy picture appears during playback, the video heads in the unit may need to be cleaned.

1. Please visit your local Audio / Video store and

purchase a good quality VHS Video Head Cleaner.

2. If a Video Head Cleaner does not solve the

problem, please consult your dealer or an authorised service centre.

Note:

• Remember to read the instructions along with the video head cleaner before use.

• Clean video heads only when problems occur.

Accessories Supplied

• Remote control with two R6 (AA) batteries

OPEN/

INPUT

SELECT

.@/: ABC DEF

PROG.

GHI JKL MNO

PQRS TUV WXYZ

MODE

CLEAR

SPACE

REPEAT

ZOOM

AUDIO

DISC MENU TOP MENU

ENTER

DISPLAY RETURN

1.3x/0.8x

INSTANT

TIME SLIP

PLAY

SKIP

PLAY

REV

FWD

SKIPSKIP STOP

DVDPAUSE VCR

REC

DUBBING

REC MODE

SETUP

SAT.LINK

TIMER SETTIMER PROG

SE-R0273

• RF cable

• Owner’s Manual

Owner's Manual

• Quick Setup Guide

Introduction Connections Basic Setup Playback

Recording

• Registration card

Editing

Function Setup

VCR Functions Others

E9GA0BD_EN.book Page 6 Monday, March 26, 2007 10:14 AM

Table of Contents

Introduction ............................................ 2

Precautions ........................................................... 2

Features ................................................................ 7

Guide to the Owner’s Manual................................ 8

Functional Overview............................................ 11

Installing Batteries in the Remote Control........... 15

VCR / DVD Recorder Switching.......................... 15

Guide to On-Screen Displays.............................. 16

Front Panel Display Guide .................................. 18

Connections ......................................... 19

Connections ........................................................ 19

Basic Setup........................................... 22

Initial Setting........................................................ 22

Channel Setting................................................... 22

Setting the Clock ................................................. 24

Selecting the TV Aspect Ratio ............................ 25

Recording ............................................. 26

Information on DVD Recording ........................... 26

Formatting a Disc ................................................ 27

Selecting the Sound Mode .................................. 30

Basic Recording .................................................. 31

One-touch Timer Recording (OTR)..................... 32

Timer Recording.................................................. 33

Satellite Link........................................................ 36

Settings for External Equipment.......................... 38

Dubbing Mode..................................................... 39

Setting a Disc to Protect...................................... 40

Finalising Discs ................................................... 41

Playback ................................................42

Basic Playback .................................................... 42

PBC Function for Video CDs ............................... 47

Special Playback ................................................. 48

Search ................................................................. 52

Repeat / Random / Programme Playback /

Slide Show........................................................... 53

Selecting the Format of Audio and Video ............ 55

Editing ................................................... 57

Disc Editing.......................................................... 57

Editing Discs........................................................ 57

Function Setup .....................................64

Playback .............................................................. 66

Display................................................................. 69

Video ................................................................... 69

................................................................... 70

DivX

Reset All .............................................................. 71

VCR Functions......................................72

Playback .............................................................. 72

Recording and One-touch Timer Recording

(OTR)................................................................... 72

Search ................................................................. 73

Other Operations ................................................. 74

Hi-Fi Stereo Sound System ................................. 74

Others .................................................... 75

Troubleshooting................................................... 75

Language Code ................................................... 79

Glossary .............................................................. 80

Specifications ...................................................... 81

E9GA0BD_EN.book Page 7 Monday, March 26, 2007 10:14 AM

Features

This unit not only plays back DVDs, CDs and VHS tapes but also offers features for you to record on DVD discs and edit them after that. The following features are offered with this unit.

Recording

The unit is compatible with DVD-RW, DVD+RW discs, which are recordable repeatedly, and DVD-R, DVD+R discs, which are recordable only once. Also, this unit allows you to record to the video cassette tape. You can choose either one for your convenience.

DVD mode VCR mode

Recording up to 12 programmes:

You can programme the unit to record up to 12 programmes, up to a month in advance. Daily or weekly programme recordings are also possible.

One-touch Timer Recording:

You can set your required recording time easily. Every time [REC recording time will be increased by 30 minutes up to 8 hours. It will be turned off automatically when the recording time you set is finished.

Dubbing mode:

You can copy a DVD disc to a videotape or copy a videotape to a DVD disc. This function will be available only if the DVD disc and the videotape are not copy-protected.

Left channel stereo recording:

This unit can record the sound of the Left channel monaural input as Left and Right channels automatically (available only for AV3 jacks on the front panel).

DVD mode

Automatic Chapter marker setting:

Chapter markers will be added to recordings as you set them in the Setup menu before starting to record.

Automatic Title menu making (Video, +VR mode only):

The unit creates Title menus automatically when finalising discs.

Automatic Playlist making (VR mode DVD-RW disc only):

The unit creates a Playlist automatically after recording.

Automatic finalising (Video mode DVD-RW/-R, DVD+R disc):

You can finalise discs automatically at the end of the disc space if you set this in the Setup menu.

Playback

DVD mode

Theatre surround sound:

When the unit is connected to an amplifier or a decoder compatible with Dolby Digital or DTS, you can enjoy theatre-quality surround sound from discs recorded with the surround sound system.

I] is pressed during recording, the

Chasing Playback during Recording and Simultaneous Playback and Recording:

You can play the already recorded part of the current recording or another title during recording.

Quick search:

You can easily find the part you want to watch using the search function. Search for a desired point on a disc by title, chapter / track or time.

Playback from Original or a Playlist (VR mode):

You can play back titles using either the Original list or a Playlist.

Virtual Surround System:

You can enjoy stereophonic space through your existing 2 channel stereo system.

Playing back on MP3 / JPEG / DivX

You can enjoy MP3 files which are recorded on CD-RW/-R.

files can also be recorded on DVD-RW/-R and

DivX DVD+RW/+R discs.

VCR mode

Quick search for what you want to watch:

You can easily find the part you want to watch using the Index or Time search functions. An index mark will be assigned at the beginning of each recording you make. For Time search function, you can go to a specific point on a tape by entering the exact amount of time you wish to skip.

files:

Editing

DVD mode

Set / clear chapter markers (Video mode DVD-RW disc only) [ Page 60]

You can easily add chapter markers at every selected time interval in your recordings for easy editing.

Adding or Deleting Chapter Marks Manually

[ Pages 59 - 60] You can add or delete chapter marks.

Creating Titles to a Playlist (VR mode DVD-RW discs only) [ Page 62]

You can create a title to the Playlist.

Deleting Titles [ Page 58] You can delete titles which you do not need anymore.

Deleting a Scene of a Title (VR mode DVD-RW discs only) [ Page 63]

You can delete a specific scene of a title.

Editing title name [ Page 58] You can name titles or change the title name.

Combining Titles (VR mode DVD-RW discs only) [ Page 61] You can combine two titles into a single title.

Dividing Titles (VR mode DVD-RW, DVD+RW discs only) [ Page 61]

You can divide a title into two new titles.

Protecting titles (VR mode DVD-RW disc only):

To avoid accidental editing or erasing of titles, the protect function is useful when set to “ON” in the Original list.

Hiding chapters (+VR mode only):

To keep others from playing back some chapters without permission, you can hide chapters.

Introduction Connections Basic Setup Playback

Recording

Editing

Function Setup

VCR Functions Others

VD+RWW

VD+R

VCD

MP3

JPEG

DivX

E9GA0BD_EN.book Page 8 Monday, March 26, 2007 10:14 AM

Compatibility

DVD mode

Playing back discs recorded in Video mode on any regular DVD player:

Discs recorded in Video mode can be played back on regular DVD players, including computer DVD drives compatible with DVD-Video playback. You will need to finalise the discs recorded in Video mode to play back in other DVD players. Although DVD+RW/+R discs are playable on other units without finalisation in most cases, it is recommended to finalise in order to stabilise the performance.

* DVD-Video Format (Video mode) is a new format for

recording on DVD-RW/-R discs that was approved by the DVD Forum in 2000. Adoption of this format is optional for manufactures of DVD playback devices and there are DVD-Video players, DVD-ROM drives and other DVD playback devices available that cannot play back DVD-RW/-R discs recorded in the DVD-Video Format.

DVD mode VCR mode

PDC:

This system assures that the TV programme you wish to record using timer recording will be recorded exactly from beginning to end even if the actual broadcasting time differs.

Others

Progressive scan system:

Unlike conventional interlace scanning, the progressive scan system provides less flickering and images in higher resolution than that of traditional television signals.

Guide to the Owner’s Manual

Symbols Used in the Owner’s Manual

To show what recording mode or disc type applies to each function, the following symbols appear at the beginning of each operating item.

Symbol Description

DVD-VDVD-V

Video

DVD-RWDVD-RW

DVD-RDVD-R

DDVD+R

DVD+RW

DDVD+R

DVD+R

CDCDCD

VCD

MP3

JPEG

DivX

VCRVCR

Available to DVD-Videos

Available to DVD-RW discs in Video mode

Available to DVD-RW discs in VR mode

Available to DVD-R discs in Video mode

Available to DVD+RW discs

Available to DVD+R discs

Available to Audio CDs

Available to Video CDs

Available to CD-RW/-R discs with MP3 files

Available to CD-RW/-R, discs with JPEG files

Available to DVD-RW/-R, DVD+RW/+R

and CD-RW/-R discs with DivX

Available to VHS tapes Use only cassettes marked VHS ( ).

files

PAL

VD+RWW

VD+R

E9GA0BD_EN.book Page 9 Monday, March 26, 2007 10:14 AM

Discs for Recording, Playing

Disc Type

Logo

DVD-RW DVD-R DVD+RW DVD+R

Introduction Connections Basic Setup Playback

Format

Icon

Maximum Record Time

Recordable/Playable

Recording Features

Record TV Programmes

Reuse by deleting the current contents

Record 16:9 size pictures

Available Features

Record copy-once programmes

Create chapters at fixed intervals (auto chapter)

Editing Features

Scene Delete

Edit Title Name

Create chapters wherever you like (chapter mark)

Divide a title

Combine titles

Hide chapters

Delete a title

Create a playlist

Protect a title

Versions

Compatibility

Automatically formatted in Video mode

DVD-RDVD-R DDVD+R

480 min (12 cm) 144 min (8 cm)

Ver. 2.0 Ver. 2.0/4× Ver. 2.0/8× Ver. 2.0/16×

Playable on most DVD players. Finalisation necessary. (Title menu will be created)

Can be formatted in VR or Video mode

Video Mode VR Mode

Video

DVD-RWDVD-RW

480 min (12 cm) 144 min (8 cm)

Ver. 1.1,1.2 Ver. 1.1/2× CPRM compatible Ver. 1.2/4× CPRM compatible

Playable on most DVD players. Finalisation necessary. (Title menu will be created)

DVD-RWDVD-RW

480 min (12 cm) 144 min (8 cm)

Playable only on VR mode compatible unit. Finalisation recommended.

✔✔✔✔✔

✔✔ ✔

✔✔✔

✔*

✔✔✔✔✔

Playlist Original

✔✔

✔✔✔✔ ✔ ✔

✔✔ ✔✔

✔ ✔

✔

✔✔✔✔ ✔ ✔

✔

Automatically formatted in +VR mode

DVD+RW DDVD+R

480 min (12 cm) 144 min (8 cm)

1×-4× 1×-16×

Playable on DVD+RW compatible players. Finalisation recommended. (Title menu will be created)

Automatically formatted in +VR mode

DVD+R

480 min (12 cm) 144 min (8 cm)

Playable on most DVD players. Finalisation recommended. (Title menu will be created)

✔✔

✔: Available Gray: Not available

*CPRM compatible disc only.

Because of problems and errors that can occur during the creation of DVD and CD software and/or the manufacture of DVD and CD discs, Toshiba cannot guarantee that product will play every feature of every DVD bearing the DVD logo and/or every CD bearing the CD logo. As one of the creators of DVD technology, Toshiba DVD players are manufactured using the highest standards of quality, and as a result, such incompatibilities are rare.

Recording

Editing

Function Setup

VCR Functions Others

DVD players with are capable of playing DVD-RW recorded in VR mode.

VCD

MP3

JPEG

DivX

E9GA0BD_EN.book Page 10 Monday, March 26, 2007 10:14 AM

Discs for Playing

Disc Type

DVD-VIDEO CD-DA Video CD CD-RW CD-R

Logo

Icon

Typ e of

title

Icon

DVD-VDVD-V CDCDCD VCD

Files for Playing

MP3 JPEG DivX

MP3

MP3 JPEG

JPEG DivX

DivX

CD-RW/-R

Media

CD-RW/-R CD-RW/-R

DVD-RW/-R

DVD+RW/+R

is a trademark of DVD Format/Logo Licensing

Corporation.

• Official DivX® Certified product; Plays DivX® 6.0,

5, DivX® 4, DivX® 3, and DivX®VOD video

DivX content (in compliance with DivX Certified™ technical requirements).

• Discs containing the DivX (Global Motion Compensation) playback feature, which is DivX

supplemental function, cannot be

files with the DivX® GMC

played back on this unit.

* This unit cannot play back the disc contents

protected by Windows Media Digital Rights Management (DRM).

Unplayable Discs

The following discs will not play back on this unit.

• CD-ROM • Compact Disc-Interactive (CD-I)

• Video Single Disc (VSD) • DVD-ROM

• DVD-audio • Unfinalised disc

• DVD contains MP3, Windows Media™ Audio or JPEG files

• DVD-R recorded in VR format or non compatible recording format

On the following disc, the sound may not be heard.

• Super audio CD - Only the sound on the CD layer can be heard. The sound on the high-density super audio CD layer cannot be heard.

Colour Systems

DVDs are recorded using different colour systems throughout the world. The most common colour system, used primarily in the U.K. and other EU countries, is PAL. This unit uses the PAL system. However, it is also possible to play back DVDs using other colour systems, such as NTSC.

Region Codes

This unit has been designed to play DVD with region 2. DVD must be labelled for ALL regions or for region 2 in order to play on the unit. You cannot play back DVD that are labelled for other regions. Look for the symbols on the right on your DVD. If these region symbols do not appear on your DVD, you cannot play back the DVD in this unit.

VCD CDCDCD CDCDCD

The number inside the globe refers to region of the world. A DVD labelled for a specific region can only play back on the unit with the same region code.

Following discs are recommended for good recording quality and are proven to be compatible with this unit. However, depending on the media condition the unit may not read the disc properly. Verbatim DVD+R 8x, DVD+RW 4x, DVD-R 8x,

DVD-RW 2x JVC DVD-RW 4x Maxell DVD+R 4x/8x/16x, DVD-R 8x/16x SONY DVD+R 4x/8x/16x, DVD+RW 4x TDK DVD+R 4x/8x/16x Performance of any other discs are not guaranteed.

• Toshiba is not liable for any damage or loss caused directly or indirectly by the malfunction of this unit, including, without limitation, any one of the following:

• Failure to record contents intended to be recorded by the consumer.

• Failure to edit contents as intended by the consumer.

• When a DVD-RW/-R, DVD+RW/+R disc created on this unit is used (e.g., insertion, playback, recording or editing) in another DVD player, recorder or personal computer drive.

• When a DVD-RW/-R, DVD+RW/+R disc that is used in the manner described in the immediately preceding bullet point is used again in this unit.

• When a DVD-RW/-R, DVD+RW/+R disc that was recorded in another DVD recorder, or in a personal computer drive is used in this unit.

• Some functions may not work with personal computer discs.

• Discs recorded in this unit may not operate as expected on other DVD players, recorders or personal computer drives.

E9GA0BD_EN.book Page 11 Monday, March 26, 2007 10:14 AM

Functional Overview

Front Panel

Introduction Connections Basic Setup Playback

1 23*456

REC DUBBING

ON / STANDBY

VCR

18 15 1419*20* 1617* 1312 9*10 8

1 ON / STANDBY button

• Press to turn on or off the unit.

• Green LED lights up when power is ON.

2 Cassette compartment (VCR)

• Insert a tape here.

3 O (OPEN / CLOSE) button* (DVD)

• Press to open or close the disc tray.

4 Disc tray (DVD)

• Place the disc here when the disc tray is opened.

5 S-VIDEO input jack (AV3) (DVD / VCR)

• Use to connect the S-Video output of external equipment with an S-Video cable.

6 VIDEO input jack (AV3) (DVD / VCR)

• Use to connect external equipment with a standard Video cable.

7 AUDIO input jacks (AV3) (DVD / VCR)

• Use to connect external equipment with a standard Audio cable.

8REC I button (DVD)

• Press once to start recording.

• Press repeatedly to start a One-touch Timer Recording.

9 P (PLAY) button* (DVD)

• Press to start or resume playback.

10 S (STOP) button (DVD)

• Press to stop a playback or recording.

• Press to stop a timer recording of DVD.

11 VCR/DVD indicator (DVD / VCR)

• Indicates the selected component (DVD or VCR).

PROGRAM

(*)

You can also turn on the unit by pressing these buttons.

VCR/DVD REC

DVD

DVDVCR

12 VCR/DVD button (DVD / VCR)

• Press to select the DVD mode or the VCR mode.

13 DUBBING button (DVD / VCR)

• Press to start VCR to DVD (DVD to VCR) duplication which you set in the Setup menu.

14 PROGRAM / buttons (DVD / VCR)

• Press to change the channel up or down.

15 Display (DVD / VCR)

• Refer to “Front Panel Display Guide” on page 18.

16 REC I button (VCR)

• Press once to start recording.

• Press repeatedly to start a One-touch Timer Recording.

17 P (PLAY) button* (VCR)

• Press to start playback.

• Press to turn on the unit and start playback when the unit is off with a tape playback.

18 O/S (STOP / EJECT) button (VCR)

• Press to remove the tape from the unit.

• Press to stop the tape playback.

• Press to stop the proceeding timer recording in VCR.

19 f (FWD) button* (VCR)

• Press to rapidly advance the video tape.

• Press to view the picture rapidly in forward during playback. (Forward Search)

• Press to turn the unit on when the video tape is inserted and start rapidly advancing the tape.

20 r (REW) button* (VCR)

• Press to rewind the video tape.

• Press to view the picture rapidly in reverse during the playback mode. (Rewind Search)

• Press to turn the unit on when the video tape is inserted and start rewinding the tape.

LRS-VIDEO VIDEOAV3

Recording

Editing

Function Setup

VCR Functions Others

Button names described in the Owner’s Manual

The instructions in this manual are described mainly with the operations using the remote control. Some operations can be carried out using the buttons on the front panel.

E9GA0BD_EN.book Page 12 Monday, March 26, 2007 10:14 AM

Rear Panel

1 Mains cable

• Connect to a standard AC outlet.

2 AV2 (DECODER) socket (DVD / VCR)

• Connect to VCR, camcorder, or other Audio-Video equipment. Use a commercially available Scart cable.

3 AV1 (TV) socket (DVD / VCR)

• Connect to the Scart socket on your TV. Use a commercially available Scart cable.

4 DIGITAL AUDIO OUT (COAXIAL) jack

(DVD)

• Connect to an amplifier with a digital input jack such as a Dolby Digital decoder, DTS decoder or MPEG decoder. Use a commercially available Coaxial cable.

DVD/VCR DVD

AV2(DECODER)

AV1(TV)

DIGITAL

AUDIO OUT

COAXIAL

AUDIO

OUT

S-VIDEO

OUT

COMPONENT

VIDEO OUT

/CB

/CR

ANTENNA

OUT

5 AUDIO OUT jacks (DVD)

• Connect to the audio input jacks on your TV. Use a commercially available Audio cable.

6 S-VIDEO OUT jack (DVD)

• Connect to the S-Video input jack on your TV. Use a commercially available S-Video cable.

7 COMPONENT VIDEO OUT jacks (DVD)

• Connect to the component video input jacks on your TV.

• Use a commercially available Component Video cable.

8 ANTENNA OUT (DVD / VCR)

• Connect to the Aerial jack on your TV, cable box or direct broadcast system. Use the supplied RF cable.

92134 5 867

9 ANTENNA IN (DVD / VCR)

• Connect to an antenna or cable.

Note

• Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the unit.

• This unit does not have an RF modulator.

E9GA0BD_EN.book Page 13 Monday, March 26, 2007 10:14 AM

Remote Control

12 13

14 15 16

OPEN/ CLOSE

.@/ :

GHI JKL MNO

PQRS TUV WXYZ

MODE

ZOOM

4 5

DISC MENU TOP MENU

DISPLAY RETURN

REV

DUBBING

SAT.LINK

ABC DEF

SPACE

AUDIO

ENTER

INSTANT

SKIP

PLAY

TIMER SET

SE-R0273

INPUT

SELECT

CLEAR

1.3x/0.8x PLAY

REC MODE

TIMER PROG

PROG.

REPEAT

TIME SLIP

FWD

SKIPSKIP STOP

DVDPAUSE VCR

REC

SETUP

17 18

20 21

24 25

30 32

33 35

5 AUDIO button (DVD / VCR)

DVD mode

• When receiving a bilingual broadcast, press to change the audio out setting to “Main”, “Sub” and “Main/Sub”.

• Press to change the bilingual audio source of an external equipment to “Main”, “Sub” or “Main/ Sub”. (Available only when the “External Input Audio” in the Setup menu is set to “Bilingual” in advance.)

• Press to display the audio menu during playback.

• Press to select the sound mode.

VCR mode

• During playback of a Hi-Fi video tape, press to change the audio out setting to “STEREO”, “LEFT”, “RIGHT” and “MONO”.

• When receiving a bilingual broadcast, press to change the audio out setting to “Main”, “Sub” and “Main/Sub”.

6 DISC MENU button (DVD)

• Press to display the Disc menu during playback.

• Press to change the Original and Playlist on the TV screen. (VR mode only)

7Direction U / D / L / P buttons

(DVD / VCR)

• Press to move the cursor and determine items or settings.

Introduction Connections Basic Setup Playback

Recording

1 OPEN/CLOSE button (DVD / VCR)

• Press to open or close the disc tray.

• Press to remove the tape from the unit.

2 Number buttons (DVD / VCR)

• Press to select channel numbers.

• Press to select a title / chapter / track on the display.

• Press to enter values for settings in the Setup menu.

• Press to enter the number in the Index or Time search in VCR mode.

• Press to enter the characters in edit function.

3 MODE button

• This button does not work for this unit.

4 ZOOM button (DVD)

• During playback, press to enlarge the picture on the screen.

8 DISPLAY button (DVD / VCR)

• Press to display the On-Screen Display.

9 INSTANT SKIP button (DVD)

• During playback, press to skip 30 seconds. (See page 48.)

10 REV r button (DVD / VCR)

DVD mode

• During playback, press to reverse fast.

• When playback is paused, press to reverse slowly.

VCR mode

• Press to rewind the video tape.

• Press to view the picture rapidly in reverse during the playback mode.

11 PLAY P button (DVD / VCR)

• Press to start or resume playback.

12 SKIP B button (DVD)

• During playback, press twice in quick successions to skip to the previous chapter or track.

• When playback is paused, press to play reverse step by step.

13 PAUSE p button (DVD / VCR)

• Press to pause playback or recording.

Editing

Function Setup

VCR Functions Others

E9GA0BD_EN.book Page 14 Monday, March 26, 2007 2:12 PM

14 DUBBING button (DVD / VCR)

• Press to start VCR to DVD (DVD to VCR) duplication which you set in the Setup menu.

15 SAT.LINK button (DVD / VCR)

• Press to call up the Satellite Link setting.

16 TIMER SET button (DVD / VCR)

• Press to set the unit in timer-standby mode. In the timer-standby mode, press to cancel the mode and to turn on the unit.

17 INPUT SELECT button (DVD / VCR)

• Press to select the appropriate input.

18 ON / STANDBY button (DVD / VCR)

• Press to turn on or off the unit.

19 PROG. / buttons (DVD / VCR)

DVD mode

• Press to change the channel up or down.

VCR mode

• Press to change the channel up or down.

• Press to adjust the tracking during playback or in slow motion of the tape.

• While playback is in still mode, you can adjust the vertically blurred picture.

20 CLEAR button (DVD / VCR)

DVD mode

• Press to clear the password once entered.

• Press to cancel the programming for a disc.

• Press to clear the selecting marker number in the marker setup mode.

• Press to clear the programme once entered in the timer recording setting mode.

VCR mode

• Press to reset the tape counter.

21 REPEAT button (DVD / VCR)

DVD mode

• Press to select the repeat mode.

VCR mode

• Press to set or release the Auto Repeat Playback.

22 SEARCH button (VCR)

• Press to call up the index or time search menu.

23 TOP MENU button (DVD)

• Press to display the Title menu.

24 ENTER button (DVD / VCR)

• Press to acknowledge or approve a menu selection.

25 RETURN button (DVD / VCR)

• Press to return to the previously displayed menu screen.

27 1.3x/0.8x PLAY button (DVD)

• During playback, press to playback in a slightly faster/slower speed while keeping the audio quality just as normal playback.

28 FWD f button (DVD / VCR)

DVD mode

• During playback, press to forward fast.

• When playback is paused, press to forward slowly.

VCR mode

• Press to rapidly advance the video tape.

• Press to view the picture rapidly in forward during playback.

29 STOP S button (DVD / VCR)

• Press to stop playing back or recording.

30 SKIP F button (DVD)

• During playback, press to skip to the next chapter or track.

• When playback is paused, press to advance step by step.

31 VCR button (DVD)

• Press to select the VCR output mode. (See page 15.)

32 DVD button (VCR)

• Press to select the DVD output mode. (See page 15.)

33 REC MODE button (DVD / VCR)

• Press to switch the recording mode.

34 REC I button (DVD / VCR)

• Press once to start a recording.

• Press repeatedly to start a One-touch Timer Recording.

35 TIMER PROG button (DVD / VCR)

• Press to display the timer programme setting menu.

36 SETUP button (DVD / VCR)

• Press to display the Setup menu in stop mode.

Button names described in the Owner’s Manual

The instructions in this manual are described mainly with the operations using the remote control. Some operations can be carried out using the buttons on the front panel.

Note

• If you turn off this unit, [OPEN / CLOSE O] on the

remote control is not available.

• Be sure to use [O

/S (STOP / EJECT)] on the unit.

(OPEN / CLOSE)] or

26 TIME SLIP button (DVD)

• Press once to start recording the TV programme you are watching. Press again to watch the content being recorded from the beginning while recording continues. (VR mode DVD-RW discs with the recording mode of LP, EP or SLP only)

E9GA0BD_EN.book Page 15 Monday, March 26, 2007 10:14 AM

Introduction Connections Basic Setup Playback

Installing Batteries in the Remote Control

Install two R6 (AA) batteries (supplied) into the remote control, carefully match with the polarity indicated inside the battery compartment.

21 3

Caution

• Incorrect use of batteries can result in hazards such as leakage and bursting.

• Do not mix new and old batteries together.

• Do not use different kinds of batteries together.

• Make sure that the plus and minus ends of each battery match the indications inside the battery compartment.

• Remove batteries if the equipment will not be used for a month or more.

• When disposing used batteries, please comply with governmental regulations or the public instructions for environmental protection that apply in your country or area.

• Do not recharge, short-circuit, heat, burn or disassemble batteries.

About the Remote Control

• Make sure there is no obstacle between the remote control and the remote control sensor on the unit.

• Use within the operating range and angle as shown.

VCR / DVD Recorder Switching

Because this product is a combination of a VCR and a DVD recorder, you must select first which component you wish to operate.

DVDVCR

PROGRAM

VCR/DVD REC

DVD

DVDVCR

DVD indicator

VCR indicator

REC DUBBING

ON / STANDBY

VCR

VCR/DVD

VCR mode

Press [VCR] on the remote control. (Verify that the VCR indicator is lit.)

DVD mode

Press [DVD] on the remote control. (Verify that the DVD indicator is lit.)

Note

• You can also press [VCR/DVD] on the front panel to

switch between DVD and VCR mode.

• You cannot switch to the mode (DVD or VCR) that is in the timer-standby mode.

Recording

Editing

ON / STANDBY

REC DUBBING

VCR

PROGRAM

VCR/DVD REC

DVD

DVDVCR

Within about 7 m

Remote control

• The maximum operable range as follows:

Line of sight: approximately 7 m Either side of centre: approximately 7 m within

• Remote control operation may become unreliable if the remote control sensor of the unit is being exposed by the strong sunlight or fluorescent light.

• Remote controls for different devices can interfere with each other. Be careful when using remote controls for other equipment located close to the unit.

• Replace the batteries when the operating range of the remote control reduces.

30 degrees

Function Setup

VCR Functions Others

E9GA0BD_EN.book Page 16 Monday, March 26, 2007 10:14 AM

Guide to On-Screen Displays

DISPLAY Menu

DVD mode

Press [DVD] first.

With a disc inserted into the unit, press [DISPLAY] to display the On-Screen Display. The menu shows information about what is recorded on the disc.

RW VR ORG

P01 BBC1

SP 1:53

Press [DISPLAY] while the On-Screen Display is displayed to display Title Name Information or File Name Information.

Title Name

My Title

111

(only when DVD+RW/+R, VR mode DVD-RW/-R, or unfinalised Video mode DVD-RW/-R disc is in playback)

File Name

My File

111

(only when a CD with MP3/JPEG/DivX® files is in playback)

1 Displays title/file name.

This is an example screen for explanation. Displayed items vary depending on the actual mode.

1 Indicates a disc type and format mode.

2 Indicates a type of titles for VR mode

DVD-RW disc.

3 Indicates a channel number, station

name or selected external input mode.

4 Indicates a recording mode and possible

recording time left.

5 Indicates a title number, chapter number,

elapsed time and total of disc playback.

6 Each icon means:

: Search

: Audio

: Subtitle

: Angle

: Repeat

: Marker

: Noise Reduction / Black Level

: Zoom

: Surround

7 Indicates an operation status.

Note

• In some descriptions on this manual, only one disc type is indicated as an example.

VCR mode

Press [VCR] first. Press [DISPLAY] to display the On Screen Display.

12:00

AV2

STEREO

This is an example screen for explanation. Displayed items are depending on the actual mode.

0:00:00

STEREO

1 Current time

2 Position number

3 Audio status of the receiving broadcast

or external equipment

4 Audio status of the currently playing

back video tape

5 Tape counter

6 Recording or playing back speed

7 Status of the current tape

While in the VCR mode, the On Screen Display of the VCR mode is displayed.

E9GA0BD_EN.book Page 17 Monday, March 26, 2007 10:14 AM

Main Menu

Press [SETUP] to display the main menu. Then use

K / L] to select a menu and press [ENTER] to

[

display the sub menu. These menus provide entries to all main functions of the unit.

Setup

General Setting

Timer Programming

Title List

DVD Menu

CD Playback Mode

1 General Setting:

To go to General Setting menu.

2 Timer Programming:

To programme a timer recording.

3 Title List:

To call up the title list.

4DVD Menu:

To set up the DVD disc setting.

5 CD Playback Mode:

To set up the CD playback setting.

• “CD Playback Mode” is available only when an audio CD, a video CD, a CD-RW/-R with MP3 / JPEG / DivX

files is inserted into the unit.

8 Reset All:

To reset the setting to the factory default.

9 : DVD

: VCR

Indicates the available mode for the selected function.

DVD Menu / CD Playback Mode

DVD Menu

Format

Finalise Disc Protect OFF ON

Delete All Playlists

CD Playback Mode

Random Play

Program Play PBC (Video CD only)

Slide Show

1 Format (DVD-RW, DVD+RW only):

Allows you to format the disc.

Introduction Connections Basic Setup Playback

Recording

General Setting Menu

General Setting

1 2

Playback Display

Video

Recording Clock

Channel

DivX Reset All

7 8

Parental Lock Audio Out Disc Menu Language Audio Language Subtitle Language Angle Icon Still Mode TV System

1 Playback:

To set up the unit to play discs as you prefer.

2Display:

To set up the OSD screen as you prefer.

3Video:

To set up the video setting.

4 Recording:

To set up the unit to record to discs as you prefer.

5Clock:

To set up the clock of the unit as you need.

6Channel:

To adjust the channel setting of the unit as you prefer.

2 Finalise:

Allows you to finalise a disc containing recorded titles.

3 Disc Protect (VR mode DVD-RW,

DVD+RW/+R disc only):

Allows you to protect a disc from accidental editing or recording.

4 Delete All Playlists (VR mode DVD-RW

disc only):

Allows you to delete Playlist.

5 Random Play:

Allows you to activate the random playback feature.

6 Program Play (audio CD/video CD only):

Allows you to activate the programme playback feature.

7 PBC (Video CD only):

Allows you to select images or information on the menu screen by activating PBC (playback control) function.

8 Slide Show (JPEG files only):

Allows you to select the display time of the slide show mode.

Editing

Function Setup

VCR Functions Others

7DivX:

To set up the setting for the DivX® playback.

E9GA0BD_EN.book Page 18 Monday, March 26, 2007 10:14 AM

Front Panel Display Guide

1 Current status of the unit

p : Appears when disc playback is paused.

Appears also during step by step playback.

B : Appears when playing back a disc.

: Appears during slow forward playback.

: Appears when the timer programming or

One-touch Timer Recording (OTR) is set and is operating. Appears when the unit goes into the Satellite Link standby mode. Flashes when all the timer programmes are finished. Flashes when there is an error in programming.

I: Appears when recording.

Flashes when recording being paused.

: Appears when a tape is in the unit.

DB: Appears when dubbing.

: Appears when a disc is in this unit.

DVD: Appears when this unit is in DVD output

mode, or the timer-standby mode for DVD recording. Flashes when switch to the timer-standby mode while programming cannot set. Flashes when a programme cannot be performed for some reasons.

VCR

DVD

VCR: Appears when this unit is in VCR output

mode, or the timer-standby mode for VCR recording. Flashes when switch to the timer-standby mode while programming cannot set. Flashes when a programme cannot be performed for some reasons.

I, , DB, and DVD will be displayed

simultaneously during VCR to DVD duplication process.

I, , DB, and VCR will be displayed

simultaneously during DVD to VCR duplication process.

2 Title / Track and Chapter number

: Title / track number : Chapter number

3 Displays the following

• Playing back time

• Current title / chapter / track number

• Recording time / remaining time

•Clock

• Channel number

• VCR tape counter

• One-touch Timer Recording (OTR) remaining time

Display Messages

The disc tray is opening.

DVD

The PBC function of the Video CD is

DVD

activated.

The disc tray is closing.

DVD

A disc is loading.

DVD

Data is being recorded on a disc.

DVD

E9GA0BD_EN.book Page 19 Monday, March 26, 2007 10:14 AM

Connections

Introduction Connections Basic Setup Playback

Audio/Video cable (not supplied)

Scart/RCA cable

Scart adaptor (not supplied)

(not supplied)

DVD/VCR DVD

AV2(DECODER)

AV1(TV)

Connections

Connecting to a TV

Connect the unit to a TV after considering the capabilities of your existing equipment.

Before installation, plug off your TV and this unit. Using the Scart socket

1 Connect the antenna or cable to the

ANTENNA IN jack of this unit.

2 Connect the ANTENNA OUT jack of

this unit to the Aerial jack of your TV. Use the supplied RF cable.

3 Connect AV1 (TV) Scart socket of

this unit to the Scart socket of your TV. Use a commercially available Scart cable.

Note

• If your TV does not have a Scart socket, use a commercially available Scart adaptor or Scart/RCA cable to connect. Use only AV1 (TV) or AV2 (DECODER) socket for the VCR output signals of this unit.

• Connect this unit directly to the TV. If the AV cables are connected to a VCR, pictures may be distorted due to the copy protection system.

• Teletext can only be output in VCR mode through AV1 (TV) out.

• When changing the “Video Out” setting (“SCART (RGB)”, “Component Interlace (I)” or “Component Progressive (P)”), connect to the corresponding jack on the TV. If the setting is changed, for example, to “Component Interlace (I)” or “Component Progressive (P)” while the scart cable is connected to the TV, a distorted video signal may be output.

To A e r i al j a c k

Antenna

Scart cable (not supplied)

ANTENNA

COMPONENT

S-VIDEO

AUDIO

DIGITAL

VIDEO OUT

AUDIO OUT

OUT

COAXIAL

/CB

/CR

OUT

Selecting Progressive Scan (625p/525p or Interlaced 625i/525i) Playback

• If your TV is compatible with progressive scanning (625p/525p), connect the TV to the COMPONENT VIDEO OUT jacks of the unit and set “Video Out” setting to “Component Progressive (P)” in the setup menu. (See page 69.) Next, set your TV to the progressive scan mode.

• If your TV is not compatible with progressive scan, set “Video Out” setting to “Component Interlace (I)”.

• Use a commercially available adaptor if the Video input jacks of your TVs or monitors are the BNC type.

RF cable (supplied)

RF cable (not supplied)

Using the S-VIDEO OUT or the COMPONENT VIDEO OUT jacks and the AUDIO OUT jacks (Only for DVD)

If your TV has an S-Video or a Component Video input jack, use either an S-Video cable (to connect the S-VIDEO OUT jack) or a Component Video cable (to connect the COMPONENT VIDEO OUT jacks), and an Audio Cable (to connect the AUDIO OUT jacks).

• S-Video connection provides the good quality picture.

• Component connection provides the better quality picture.

1 Follow steps 1 and 2 on the left. 2 Connect S-VIDEO OUT or

COMPONENT VIDEO OUT jacks of this unit to the S-Video or Component Video input jacks of your TV. Use a commercially available S-Video cable or Component video cable.

3 Connect the AUDIO OUT jacks of this

unit to the analogue Audio input jacks of your TV. Use a commercially available Audio cable.

Cable Signal

Recording

Editing

Function Setup

VCR Functions Others

E9GA0BD_EN.book Page 20 Monday, March 26, 2007 10:14 AM

Component

Component Video Cable (not supplied)

ANTENNA

COMPONENT

S-VIDEO

VIDEO OUT

OUT

/CB

/CR

OUT

Video IN

YPB/CB PR/CR

Audio cable (not supplied)

S-VIDEO INAUDIO IN

S-Video cable (not supplied)

DVD/VCR DVD

AV2(DECODER)

AV1(TV)

DIGITAL

AUDIO OUT

COAXIAL

AUDIO

OUT

Note for a TV with no S-Video input jack or Scart socket:

• This unit has no RF modulator, so this type of TV cannot be used.

• Only component connection is compatible with the Progressive Scan.

Connecting to External Equipment

This unit has three input terminals, AV1 or AV2 on the rear panel and AV3 on the front panel. Be sure that all the units are off before making connections.

Recording from a DVD player, VCR, Satellite Box or other Audio-Video equipment with a Scart output socket (AV2)

AV3 ( F r o n t )

DUBBING VCR/DVD REC

S-Video cable (not supplied)

• When connecting an external device of monaural output to this unit, use AUDIO L jack of AV3.

DVDVCR

DVD

S-VIDEO

OUT

LRS-VIDEO VIDEOAV3

Audio cable (not supplied)

AUDIO

OUT

Digital Audio for Better Sound Quality (Only for DVD)

Dolby Digital decoder, DTS decoder or MPEG decoder, etc.

Digital audio

input jack

COAXIAL

AV output socket (Scart)

Scart cable (not supplied)

AV2 ( D E C O D E R )

DVD/VCR DVD

AV2(DECODER)

AV1(TV)

DIGITAL

AUDIO OUT

COAXIAL

ANTENNA

COMPONENT

S-VIDEO

AUDIO

VIDEO OUT

OUT

/CB

/CR

OUT

Note

• When you record a TV programme from a Satellite Box, you must connect a Scart cable to AV2(DECODER). (See page 36.)

• When AV2 is connected, the signal from the AV2 will be output automatically. If you want to monitor the signal from other input, you must press [DISPLAY] first. Then, select the desired input to monitor with [INPUT SELECT ].

Recording from a camcorder or other Audio-Video equipment with no Scart output socket (AV3)

If no S-Video input jack is available, connect to VIDEO input jack on the front panel using an RCA Video cable. Change the setup when using S-VIDEO input jack. (See page 38.)

DIGITAL

AUDIO OUT

COAXIAL

Coaxial cable (not supplied)

DVD/VCR DVD

DIGITAL

AV2(DECODER)

AUDIO OUT

COAXIAL

AV1(TV )

ANTENNA

COMPONENT

S-VIDEO

AUDIO

VIDEO OUT

OUT

/CB

/CR

OUT

The connections illustrated above are optional for better sound.

1 For clear digital sound quality, use

the DIGITAL AUDIO OUT (COAXIAL) jack to connect your digital audio equipment.

If the audio format of the digital output does not match the capabilities of your receiver, the receiver will produce a strong, distorted sound or no sound at all.

E9GA0BD_EN.book Page 21 Monday, March 26, 2007 10:14 AM

Connecting a Dolby Digital™ decoder, DTS decoder or MPEG decoder

• Connecting multi-channel Dolby Digital decoder allows you to enjoy the Multi-channel Dolby Digital surround system as well as DTS decoder, Multichannel surround system.

• After connecting to a Dolby Digital decoder, set “Dolby Digital” to “Stream” in the Audio Out menu. (See page 67.)

• After connecting to a DTS decoder, set “DTS” to “ON” in the Audio Out menu. (See page 67.)

• After connecting to a MPEG decoder, set “MPEG” to “Stream” in the Audio Out menu. (See page 67.)

Connecting to an MD deck or DAT deck

• The audio source recorded in Dolby Digital Multichannel surround format cannot be recorded using an MD or DAT deck as a digital sound.

• If not connected to a Dolby Digital decoder, set “Dolby Digital” to “PCM” in the Audio Out menu. Playing back a DVD using incorrect settings may generate noise distortion and damage speakers.

• Set “Dolby Digital” and “MPEG” to “PCM” and set “DTS” to “OFF” in the Audio Out menu for connecting to an MD or DAT deck.

• You can use AUDIO OUT jacks for the connection of your audio system.

Introduction Connections Basic Setup Playback

Recording

After You Have Completed Connections

Switch the input selector on your TV to an appropriate external input channel. For details, refer to the Owner’s Manual of your TV.

Note

• Connect this unit directly to the TV. If the AV cables are connected to a VCR, pictures may be distorted due to the effects of the copy protection system.

Editing

Function Setup

VCR Functions Others

E9GA0BD_EN.book Page 22 Monday, March 26, 2007 10:14 AM

Basic Setup

Initial Setting

Turn on this unit for the first time, you need to follow these steps.

1 Press [ ON / STANDBY]. 2 Turn the TV on. Select the input to

which the unit is connected.

3 Press [ENTER] to start Channel Tuning.

The unit will start getting channels available in your area.

Initial Setting

Auto Tuning

Make sure the antenna is connected to “ANTENNA IN” jack.

Start

4 After finished channel setting,

“Clock Setting” will appear. Then press [ENTER].

Initial Setting

Channel Setting

Tuning of this unit to broadcast channels can be performed in two ways.

Auto Tuning

Programme the tuner to scan only the channels you can receive in your area.

1 In stop mode, press [SETUP]. Select

“General Setting” using [U / D], then press [ENTER].

General Setting Menu will appear.

2 Select “Channel” using [U / D], then

press [ENTER].

3 Select “Auto Tuning” using [U / D],

then press [ENTER].

The unit will start storing channels available in your area.

General Setting

Playback Display Video Recording Clock Channel DivX Reset All

Auto Tuning Manual Tuning Move

Clock Setting

- - / - - / - - - - ( - - - )

- - : - -

5 Follow to step 5 on page 25 in

“Manual Clock Setting”.

Wait for several minutes to finish channel storing.

4 Press [SETUP] to exit.

You can select the channels memorised only in this unit by using [PROG. / ].

To cancel auto tuning Press [RETURN] or [SETUP] during scanning.

Note

• The selection will be affected by how you receive TV channels in your local area.

• If the auto tuning is cancelled during scanning, some channels not yet tuned may not be received.

• You cannot change the channel when either VCR or DVD is in any recording mode (normal recording, One-touch Timer Recording or timer recording).

• Sorting of TV channels from P01 to P06 will be performed automatically as follows. P01: BBC1 P02: BBC2 P03: ITV P04: CH4 P05: CH5 P06: SKY NEWS

• If you are using a satellite receiver, turn it on and select SKY NEWS before commencing tuning.

E9GA0BD_EN.book Page 23 Monday, March 26, 2007 10:14 AM

Manual Tuning

Manually tune each channel.

1 In stop mode, press [SETUP]. Select

“General Setting” using [U / D], then press [ENTER].

2 Select “Channel” using [U / D], then

press [ENTER].

3 Select “Manual Tuning” using

[U / D], then press [ENTER].

4 Select “Position” using [U / D], then

press [P].

Manual Tuning

Position

Channel

Decoder

Skip

“P01” is highlighted.

P01

OFF

5 Select the position number you wish

to use using [the Number buttons] or [U / D], then press [L].

You can select position numbers 01 to 99.

6 Select “Channel” using [U / D], then

press [P].

7 Press [U / D] to start scanning.

• The tuner will begin to search up or down automatically. When a channel is found, the unit will stop searching and the picture will appear on the TV screen.

• You can select a desired channel number using [the Number buttons]. Refer to the following Channel Plan table and press the three digits to select the channel number. (To select channel 4, press [0] first and then press [0] and [4]. Or press [4] and then “– – 4” appears and wait for 2 seconds.)

• If this is the channel you want, press [L].

Channel Plan

CH Indication TV Channel

01 – 10 IRA-IRJ, GAP 21 – 69 E21 – E69 74 – 78 X, Y, Z, Z+1, Z+2

80 – 99, 100 S1 – S20, GAP

121 – 141 S21 – S41

This unit can receive the Hyper and Oscar frequency bands.

• If “Skip” is set to “ON”, select “Skip” using

[U / D], then press [P]. Select “OFF” using [U / D], then press [L].

• If you want to decode scrambled signals, select

“Decoder” using [U / D], then press [P]. Select “ON” using [U / D], then press [L].

• To store another channel, repeat steps 4 to 7.

8 After completion, press [SETUP] to

exit.

To Select a Channel

You can select a channel using [PROG. / ], or directly enter the channel using [the Number

buttons] on the remote control.

Notes on using [the Number buttons]:

• Enter channel numbers as a two-digit number for the quickest result. For example, to select channel 6, press [0] and [6]. If you only press [6], channel 6 will be selected after 2 seconds. You can only select channels 1 to 99.

• You can select the external input mode “AV1”, “AV2” or “AV3”.

• To select “AV1”, press [0], [0], [1].

• To select “AV2”, press [0], [0], [2].

• To select “AV3”, press [0], [0], [3].

To Skip a Preset Channel

You can set the unit to skip channels. You can no longer receive or seldom watch when you access channels using [PROG. / ].

1 Follow steps 1 to 3 in “Manual

Tuning” on page 23.

2 Select “Position” using [U / D], then

press [P].

3 Select the position number you wish

to skip using [the Number buttons] or [U / D], then press [L].

4 Select “Skip” using [U / D], then

press [P].

5 Select “ON” using [U / D], then

press [L].

• To skip another channel, repeat steps 2 to 5.

6 Press [SETUP] to exit.

Introduction Connections Basic Setup Playback

Recording

Editing

Function Setup

VCR Functions Others

E9GA0BD_EN.book Page 24 Monday, March 26, 2007 10:14 AM

Move

You can replace two channels.

1 In stop mode, press [SETUP]. Select

“General Setting” using [U / D], then press [ENTER].

2 Select “Channel” using [U / D], then

press [ENTER].

3 Select “Move” using [U / D], then

press [ENTER].

4 Select the position number of which

you want to change the channel using [U / D], then press [ENTER].

You cannot select a position number where “– – –” appears next to the number, because “Skip” is set to “ON” for that position number.

5 Move the channel to another

position number using [U / D], then press [ENTER].

• To move another channel, repeat steps 4 to 5.

6 Press [SETUP] to exit.

Setting the Clock

Auto Clock Setting

Channel Tuning must be set before setting Auto Clock.

1 In stop mode, press [SETUP]. Select

“General Setting” using [U / D], then press [ENTER].

2 Select “Clock” using [U / D], then

press [ENTER].

General Setting

Playback Display Video Recording Clock Channel DivX Reset All

3 Select “Auto Clock Setting” using

[U / D], then press [ENTER].

4 Select “ON” using [U / D], then

press [ENTER].

The current time will be set automatically.

5 Press [SETUP] to exit. 6 Press [ ON / STANDBY] to turn

off.

The Auto clock function is activated. This unit will search for the time every time when the power is turned off. Leave the unit off for several minutes to give it time to set the clock.

Hint

• If you want to cancel “Auto Clock Setting,” select “OFF” using [U / D], and then press [ENTER] at step 4.

Note

• The default setting of “Auto Clock Setting” is “ON.”

• The clock may set itself automatically after you connect the antenna cable to the unit and plug in the mains cable. In this case, the current time will appear on the front panel display.

• To set the clock automatically, the channel assigned to “P04” must receive the PDC signal.

• The clock cannot be set automatically if you are not receiving a channel in your area that carries a time signal. In this case, set the clock manually.

• Once the auto clock setting is performed, the unit will correct the current time by receiving PDC broadcasts whenever the power is turned off.

• The unit will correct the current time automatically at 8:00, if the unit is in standby mode.

• Between 23:00 and 1:00, the Auto Clock function will not operate even when the power is turned off.

E9GA0BD_EN.book Page 25 Monday, March 26, 2007 10:14 AM

Manual Clock Setting

1 In stop mode, press [SETUP]. Select

“General Setting” using [U / D], then press [ENTER].

2 Select “Clock” using [U / D], then

press [ENTER].

3 Select “Clock Setting” using [U / D],

then press [ENTER].

4 Press [ENTER] again.

Default date will appear.

General Setting

Playback Display Video Recording Clock Channel DivX Reset All

Clock Setting

01 / 01 / 2007 ( MON )

Clock Setting Auto Clock Setting

0 : 00

Selecting the TV Aspect Ratio

You can select the TV aspect ratio to match the format of the programme you are playing back with the unit and that of your TV screen (4:3 standard or 16:9 wide screen TV).

1 In stop mode, press [SETUP]. Select

“General Setting” using [U / D], then press [ENTER].

2 Select “Video” using [U / D], then

press [ENTER].

3 Select “TV Aspect” using [U / D],

then press [ENTER].

General Setting

Playback Display Video Recording Clock Channel DivX Reset All

TV Aspect Select Video Video Out

Introduction Connections Basic Setup Playback

Recording

5 Enter the date (day / month / year)

using [U / D].

Press [P] to move the cursor to the next field. If you wish to go back to the previous field, press [L].

6 Enter the time (hours / minutes)

using [U / D], then press [ENTER].

The clock will start.

• Although seconds are not displayed, they will be counted from zero.

7 Press [SETUP] to exit.

Note

• Your clock setting will be lost if either there is a power failure or the unit is unplugged for more than 30 seconds.

4 Select the desired option using

[U / D], then press [ENTER].

General Setting

Playback Display Video Recording Clock Channel DivX Reset All

TV Aspect

4:3 Letter Box 4:3 Pan & Scan 16:9 Wide

TV Aspect Select Video Video Out

5 Press [SETUP] to exit.

Hint

If you have a standard TV:

• Select “4:3 Letter Box” for a full width picture with black bars at the top and bottom.

• Select “4:3 Pan & Scan” for a full height picture with both sides trimmed.

If you have a wide screen TV:

• Select “16:9 Wide”.

Editing

Function Setup

VCR Functions Others

+ 58 hidden pages