Toshiba 19DV734G, 22DV733G, 22DV734G, 26DV733G Owner Manual

LCD TV/DVD COMBINATION

OWNER’S MANUAL

19DV733G
19DV734G
22DV733G
22DV734G
26DV733G

©2010 Toshiba Corporation
Before operating the unit, please read this manual thoroughly.

Owner’s Record

The model number and serial number
are on the back of your TV/DVD.
Record these numbers in the spaces
below. Refer to these numbers whenever
you communicate with your Toshiba
dealer about this TV/DVD.

Model number: _________________
Serial number: _________________

Precautions

CLASS 1
LASER PRODUCT

Note: Unless otherwise indicated, the examples used throughout this manual are based on the 26DV733G model.

CAUTION:

THIS UNIT IS A CLASS 1 LASER PRODUCT. HOWEVER THIS UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE
HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE PLAYER CORRECTLY AS
INSTRUCTED.

THE FOLLOWING CAUTION LABEL IS LOCATED ON THE REAR PANEL OF THE UNIT.

WHEN THIS UNIT IS PLUGGED INTO THE WALL OUTLET, DO NOT PLACE YOUR EYES CLOSE TO THE OPENINGS TO
LOOK INTO THE INSIDE OF THIS UNIT.

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED
HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

Headphone Warning

Loud music can damage your hearing irreversibly. Do not set the volume to a high level when listening through headphones,
particularly for extended listening periods.

Information for the DVB-T function

• Any function relative to the digital television (with the DVB logo) is available only within the country or area where such signals
are transmitted. Verify with the salesperson if it is possible to receive a DVB-T signal in the zone where you live.

• Even if the television conforms to the DVB-T specifications, the compatibility to future digital DVB-T transmissions is not
guaranteed.

• Some digital television functions may not be available in some countries.

• The DVB-T system present in this device is FTA (Free to air).

• DVB is a registered trademark of the DVB Project. This logo indicates that the product is compliant with European Digital
Broadcasting.

Possible Adverse Effects on LCD Screen

If a fixed (non-moving) pattern remains on the LCD screen for long periods of time, the image can become permanently retained
on the LCD TV panel and cause subtle but permanent ghost images. This type of damage is NOT COVERED BY YOUR
WARRANTY. Never leave your TV on for long periods of time while it is displaying the following formats or images:

• Fixed Images, such as stock tickers, video game patterns, TV station logos, and websites.

• Special Formats that do not use the entire screen. For example, viewing letterbox style (16:9) media on a normal (4:3) display
(Black bars at top and bottom of screen); or viewing normal style (4:3) media on a widescreen (16:9) display (Black bars on
left and right sides of screen).

IMPORTANT INFORMATION

DVB-C Notice

The DVB-C function may not be available to your TV, depending on the area you live and the TV firmware version. Should
you see a notice message appear on-screen when selecting the DVB-C items, please go to Toshiba’s official website at

http://www.toshiba-om.net/
information, please refer to page 12.

TV Installation

If a television is not positioned in a sufficiently stable location, it can be potentially hazardous due to falling. Many injuries,
particularly to children, can be avoided by taking simple precautions such as:

• Using stands recommended by the manufacturer of the television.

• Only using furniture that can safely support the television.

• Ensuring the television is not overhanging the edge of the supporting furniture.

• Not placing the television on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and
the television to a suitable support.

• Not standing the televisions on cloth or other materials placed between the television and supporting furniture.

• Educating children about the dangers of climbing on furniture to reach the television or its controls.

Place the TV on a stable, level surface that can support the weight of the TV. In order to maintain stability and prevent it from
falling over, secure the TV to a wall using a sturdy tie to the clip on the back of the table top stand.

to download the latest firmware, which will be released in July, to initiate the function. For more

2

Contents

Precautions ................................................................................................................................................................................ 2

Important safety information ........................................................................................................................................................ 5

Location of controls ..................................................................................................................................................................... 8

Remote control ............................................................................................................................................................................ 9

I/O connections........................................................................................................................................................................... 11

DVB-C function notice ................................................................................................................................................................ 12

Using the Auto Brightness Sensor.............................................................................................................................................. 13

Auto setup ................................................................................................................................................................................. 14

*DTV auto tuning/Setting Antenna or Cable ............................................................................................................................... 16

Selecting the video input source................................................................................................................................................. 18

Automatic station presetting with the built-in tuner .................................................................................................................... 19

Changing the order of stored channels ..................................................................................................................................... 20

Manual TV station presetting ..................................................................................................................................................... 21

Basic operation .......................................................................................................................................................................... 23

Teletext ...................................................................................................................................................................................... 25

Stereo reception with the built-in analogue tuner ...................................................................................................................... 26

Picture format ............................................................................................................................................................................ 27

AV colour adjustment ................................................................................................................................................................ 28

Other convenience functions ..................................................................................................................................................... 29

Using REGZA-LINK® ..................................................................................................................................................................32

Using the Media Player .............................................................................................................................................................. 36

Display setup/Timer setting (DTV mode only) ........................................................................................................................... 43

Password setup (Parental lock) (DTV mode only) ..................................................................................................................... 44

Version ...................................................................................................................................................................................... 45

Software upgrade (DTV mode only) .......................................................................................................................................... 46

Common interface (DTV mode only) ......................................................................................................................................... 47

Multi audio (DTV mode only) ..................................................................................................................................................... 48

DVB-Subtitle (DTV mode only)................................................................................................................................................... 49

EPG (Electronic Program Guide) (DTV mode only) .................................................................................................................. 50

EPG Timer (DTV mode only) ..................................................................................................................................................... 51

Disc ............................................................................................................................................................................................ 52

Basic playback ........................................................................................................................................................................... 53

Advanced playback ................................................................................................................................................................... 55

Zoom function/Scene navigation ............................................................................................................................................... 56

Scene bookmark ........................................................................................................................................................................ 57

Repeat playback/A-B repeat playback ...................................................................................................................................... 58

Scene angle/Title selection/DVD menu ..................................................................................................................................... 59

Soundtrack language/Audio channel/Subtitle............................................................................................................................. 60

Playback information/VCD playback control (PBC)..................................................................................................................... 61

MP3/JPEG/DivX

About the file browser/Audio file playback ................................................................................................................................ 63

Playing an audio file .................................................................................................................................................................. 64

JPEG file operation ................................................................................................................................................................... 65

®

and DivX® VOD operation .............................................................................................................................................. 66

DivX

MP3/JPEG/DivX

Programme playback/Random playback ................................................................................................................................... 69

Customising disc playback ........................................................................................................................................................ 70

Temporary cancel the rating level by DVD disc ......................................................................................................................... 76

PC connection ........................................................................................................................................................................... 77

Connecting an HDMI or DVI device to the HDMI input .............................................................................................................. 78

REGZA-LINK

Connecting TV to other equipment ............................................................................................................................................ 80

®

and Audio CD operation ............................................................................................................................... 62

®

and Audio CD playback modes ................................................................................................................... 67

®

connection ........................................................................................................................................................ 79

3

Contents

Status message ......................................................................................................................................................................... 82

Troubleshooting table ................................................................................................................................................................ 83

Specifications ............................................................................................................................................................................. 85

The GNU General Public License (GPL) ................................................................................................................................... 86

The Libpng License Notices ...................................................................................................................................................... 89

The zlib License ......................................................................................................................................................................... 90

4

Important safety information

This unit has been produced according to all current safety regulations. The following safety tips should safeguard users against
careless use and the dangers related to such use.

• Although this unit has been carefully manufactured and rigorously checked prior to leaving the factory as with all electrical
appliances, it is possible for problems to develop. If you notice smoke, an excessive build-up of heat or any other unexpected
phenomena, you should disconnect the plug from the mains power socket immediately.

• Ensure that the unit is sufficiently ventilated! Never place it next to or underneath curtains!

• This set should only be connected to an AC 110-240V/50-60Hz mains power supply. Do not attempt to connect it to any other
type of supply.

• The socket outlet must be installed near the equipment and is easily accessible.

• Do not open this unit. An attempt to repair the unit by a non-expert could be dangerous and potentially cause a fire hazard.
All repairs must be carried out by qualified service personnel only.

• Keep away from rodents. Rodents (and also cockatiels) enjoy biting electric flexes. They can cause a short circuit (fire hazard!)
and receive a fatal electric shock.

• Always hold the plug when disconnecting the unit from the socket outlet. Do not pull on flex. The flex can become overloaded
and cause a short circuit.

• Use a damp---not wet---cloth to clean the unit.

• Set up unit so that no one will trip over the flex.

• This unit is recommended to be installed on shock-free benches in order to avoid any danger from falling.

• Take note that toddlers can pull the unit down from a table or cupboard by means of its flex. Children can hurt themselves
when doing this.

• Do not use the unit near heat sources. The casing and flex could be damaged by the intensity of the heat.

• The screen is made of glass and can break if damage is done to it. Be careful when collecting sharp edged glass splitters.

• If you intend to wall mount the unit, contact the shop where you purchased the unit for advice, and leave the installation work
to professionals. Improper installation can cause damage and/or injuries.

• When installing the set on a wall, allow at least 10 cm clearance between the rear of the set and the wall. Clearance of less
than 10 cm will obstruct the vents and cause overheating to the interior of the set, resulting in faults or damage to the set.

• Taking fall-prevention measures

- If these measures are not taken, the unit can fall and cause damage and/or injuries.

- Contact the shop where you purchased the unit to obtain full details of the measures.

• When a TV stand is used,

- Ensure the unit is fully on the stand and placed in the centre.

- Do not leave the stand doors open. You could be hurt as a result of the unit falling or breaking, or your fingers being caught
or jammed. Take extra precautions if you have children.

• Avoid placing the unit on any surfaces that may be subject to vibrations or shocks.

• To protect the unit during a thunder storm, unplug the AC power cord and disconnect the aerial.
Caution: Do not touch the aerial connector.

• When you leave your home for a long period of time, unplug the AC power cord for safety.

• The unit becomes warm when in operation. Do not place any covers or blankets on the unit in order to prevent overheating.
The ventilation holes should not be blocked. Do not set up near radiators. Do not place in direct sunshine.

• When placing on a shelf, allow at least 10 cm clearance space around the whole unit.

• The unit shall not be exposed to dripping or splashing, and no objects filled with liquids, such as vases, shall be placed on the
apparatus.

• Liquids spilled into the unit can cause serious damage. Switch the set off and disconnect the mains power supply, then consult
a qualified service person before attempting to use the unit again.

• Moisture condensation occurs, for example, when you pour a cold drink into a glass on a warm day and drops of water form
on the outside of the glass. In the same way, moisture may condense on this unit’s internal optical pick-up lens, one of the
most crucial internal parts of the unit.

• Moisture condensation occurs in the following situations:

- When you move the unit from a cold place to a warm place.

- When you use the unit in a room where the heater was just turned on.

- When you use the unit in an area where cold air from an air conditioner directly hits the unit.

- When you use the unit in a humid place.

• Never use the unit when moisture condensation may occur.

• Using the unit when moisture condensation exists may damage its own internal parts and discs. Connect the power cord of
the unit to the wall outlet, turn on the unit, remove the disc, and leave it for two or three hours. After two or three hours, the
unit will warm up and moisture will be evaporated. Leaving the TV connected to the wall outlet will help prevent moisture
condensation in the unit.

• Never place hot objects or open flame sources, such as lighted candles or night lights, on or close to the TV. High
temperatures can melt plastic and lead to fires.

5

Important safety information (continued)

Slide the lever to the left

Back side of the pedestal stand

Where to install

Locate the television away from direct sunlight and strong lights; soft and
indirect lighting is recommended for comfortable viewing. Use curtains
or blinds to prevent direct sunlight from falling on the screen.

Always place the TV on a sturdy, level, stable surface that can support
the weight of the TV. In order to maintain stability and prevent the TV
from falling over, secure the TV with a sturdy strap from the hook on the
rear of the TV to a wall stud, pillar, or other immovable structure. Make
sure the strap is tight, secure, and parallel to the floor.

The LCD display panels are manufactured with extremely high-precision
technology techniques. However some non-active pixels may appear on
the screen or luminous spots may occur occasionally - this is not a sign
of a malfunction.

Note: The hook is only applicable to 26DV733G.

Make sure that the television is located in a position where it cannot be pushed or hit by objects, as pressure will break or damage
the screen, and that small items cannot be inserted into slots or openings of the case.

To display your LCD TV on the included pedestal stand

Observe the following safety precautions:
(1) Read and follow the pedestal assembly instructions included with the pedestal.

Caution: Before beginning pedestal assembly, carefully lay the front of the LCD Panel face down on
a flat, cushioned surfaces such as a quilt or blanket. Leave the bottom of the TV protruding over the

edge of the surface and assemble the pedestal as indicated below.
Note: Extreme care should always be taken when attaching the pedestal stand to avoid damage
to the LCD panel.
(2) Grab the pedestal stand and lift the display up. Confirm the pivot is locked.

(3) Place the TV on a sturdy, level surface that can support the weight of the TV.
(4) Be sure to secure the TV to a wall stud, pillar, surface, or other immovable structure. To secure the

TV in this manner: (1) attach a clip to an immovable structure, and then (2) pass a sturdy strap

through the clip and attach each end to the hooks located at the back of the TV. Be sure to leave at

least 10 cm between the TV and the wall or similar structure for ventilation.

Sturdy strap (as short as possible)

Hook

Screw

hole

Side View Top View

Clip

Screw

To fold the pedestal stand

(1) Slide the lever on the back side of the

pedestal stand to the left.
(2) Lay the display down.

Applicable to the following models:
19DV733G, 19DV734G, 22DV733G, and

22DV734G.

Note: Do not operate the LCD TV when the pedestal stand is folded. The pedestal stand should not be folded at any time
except for packing purposes.

To display your LCD TV using a wall bracket

If you decide to wall mount your LCD TV, always use a wall bracket appropriate for the size and weight of the LCD TV:

(1) Caution: Two people are required for installation.
(2) Unplug and remove any cables and/or other component connectors from the rear of the TV.
(3) Follow the instructions provided with your wall bracket. Before proceeding, make sure the appropriate bracket(s) are

attached to the wall and the back of the TV as described in the instructions provided with the wall bracket.
(4) IMPORTANT: Always use the screws supplied or recommended by the wall mount manufacturer.
(5) After attaching the appropriate bracket(s) to the wall and the back of the TV, remove the pedestal stand from the TV as

described below.

6

Important safety information (continued)

AC INPUT

Two screws

Three screws Hook

(Sturdy strap should be

as short as possible.)

AC INPUT

EXCLUSION CLAUSE

Toshiba shall under no circumstances be liable for loss and/or damage to this product caused by:
i) fire;
ii) earthquake;
iii) accidental damage;
iv) intentional misuse of the product;
v) use of the product in improper conditions;
vi) loss and/or damage caused to the product whilst in the possession of a third party;
vii) any damage or loss caused as a result of the owner’s failure and/or neglect to follow the instructions set out in the owner’s

manual;

viii) any loss or damage caused directly as a result of misuse or malfunction of the product when used simultaneously with

associated equipment;

Furthermore, under no circumstances shall Toshiba be liable for any consequential loss and/or damage including but not
limited to the following: loss of profit, interruption of business, and/or loss of recorded data whether caused during normal
operation or misuse of the product.

Removing the pedestal stand

(1) Carefully lay the front of the TV face down on a flat, cushioned surface such as a quilt or blanket. Leave the stand protruding

over the edge of the surface.

Note: Extreme care should always be taken when removing the pedestal stand to avoid damage to the LCD panel.
(2) Remove the screws shown in the diagram below. This will allow removal of the pedestal stand.

(3) Once you have removed all screws holding the pedestal stand in place, remove the pedestal stand from the TV by sliding

the pedestal stand away from the TV.

19DV733G/19DV734G/22DV733G/22DV734G 26DV733G

Note:

• 22DV733G, 22DV734G, and 26DV733G are used for illustration purposes.

• The hook is only applicable to 26DV733G.

Please take note

If stationary images generated by text services, channel identification logos, computer displays, video games, on-screen menus,
etc. are left on the television screen for any length of time, they could leave an afterimage. It is always advisable to reduce both
the brightness and contrast settings.

7

Location of controls

Adjusting the screen angle

You can adjust the angle of the TV
screen 3° forward or 12°backward from
a vertical angle. Hold the base of the TV
while adjusting the angle.

Applicable to the following models:
19DV733G, 19DV734G, 22DV733G,

22DV734G.

3

2

1

19DV733G/19DV734G/22DV733G/22DV734G

26DV733G

3

5

6

4

7

12

4

12

8
9

10

11

Note:

• The position of indicator labels on the keypad may be different depending on the model. 22DV733G, 22DV734G, and

26DV733G are used for illustration purposes.

13

14

13

14

5

6

7
8

9

10

11

Description of indicators and controls

1. POWER indicator: The Power indicator lights red in standby mode, orange in standby mode when the timer is

activated, and green when TV is powered on.

2. Remote sensor

3. Auto Brightness Sensor: This sensor will detect the ambient light conditions to optimise the backlighting level (see page

13).

4. Disc slot: Load the disc into the disc slot to view or listen.

5. EJECT: Press to eject a disc.

6. VOLUME +

7. PLAY

In DVD mode: Playback. In Menu: Functions as up menu navigation button. In Standby mode: Turn the TV on.

8. STOP

In DVD mode: Stop. In Menu: Functions as down menu navigation button. In Standby mode: Turn the TV on.

9. MENU: Press to access the menu system.

10. INPUT/ENTER: Select video input source. In Menu: Use as an ENTER button to confirm selection.

11. POWER button: Connect the supplied AC power cord to 110-240V/50-60Hz AC outlet, and then press the button to

turn the TV on and off.

12. C.I. slot: The Common Interface allows you to insert CAM (Conditional Access Module) and a suitable Smart Card to give

you access to additional Pay-TV services (see page 50). Before inserting the module, make sure to turn off the mains
power and then insert the module all the way into the slot until it is flushed with the side panel buttons.

13. HDMI 2 input: High-Definition Multimedia Interface (HDMI 2) input receives digital audio and uncompressed digital video

from an HDMI device or uncompressed digital video from a DVI device. HDMI connection is necessary to receive 1080p
signals (see pages 80-82).

14. USB terminal: For use when inserting a USB device.

/ -: Press to adjust the volume level. In Menu: Setting.

/ CHANNEL : Press to change to a higher numbered channel set into memory.

/ CHANNEL : Press to change to a lower numbered channel set into memory.

8

Remote control

Function Page

Eject a disc from the disc slot 57

Toggle between TV and DVD mode 19, 56

Toggle between analogue TV and digital TV 19

Toggle between power on and standby mode 19

- Select a channel

- Select a teletext page

- Enter the password

Display source information 27, 53, 64

Tur n the sound on/off 26

Toggle between TV, Radio, and Data modes 26

Select an input source 21

- Change the TV channel or teletext page up or down

- In standby mode: turn on the power

Increase or decrease the volume 26

26
28
47, 79

26, 28
19

- In DVD mode, view the DVD menu screen

- In JPEG CD mode, display image thumbnails

- In DVD mode, select a DVD title

- In JPEG CD mode, view the image file browser

In DTV mode, display the Digital Main Menu 19

Display the EPG (Electronic Program Guide) 53

Cursor buttons to select or adjust programming menus when a menu is on-screen 17, 18

- When using the TV menu, enable a menu option or view a sub-menu screen

- In teletext mode, display teletext page 100

- When in TV mode, display the channel list

- In ATV mode, display the Analogue Main Menu

- In DVD mode, display the DVD Setup menu

- Exit the Analogue or Digital Main Menu screen

- Cancel marking

- Exit the DVD Setup Menu screen

- Return to previous directory from Media Player sub-folder or sub-menu

Start or resume di sc playback 56

Cancel disc playback 56

- Pause the teletext display to “hold” the current page in place

- Jump to the previous chapter/track

- In teletext mode, reveal the answers to quiz questions

- During playback, play in fast reverse direction

- In teletext mode, view a sub-page

- During playback, play in fast forward direction

- In teletext mode, toggle the display size

- During playback, jump to the next chapter/track

- Fastext/TOP text buttons

- DVD control buttons

Mark specific playback points in a DVD, VCD, or audio CD 60

- In DVD mode, change the scene angle

- In JPEG CD mode, rotate the image display

Repeat playback of a specific section between two set points (A-B) 61

Toggle the teletext display on or off 28

Set the subtitle of a multi-language DVD 52, 63

- In ATV mode, select between the available broadcast audio channels

- In DTV mode, display the Multi audio menu

- Change the soundtrack language of a multi-language DVD or VCD

- In TV mode, switch to the last channel selected prior to the current one

- In DVD mode, change the image viewing scale of a video or image file

Select the specific point where to start disc playback 59

In TV/DVD mode, change the display’s aspect ratio 30

Configure the Sleep Timer 27

62
66

62
66

19
28
26

19
73

19
60

73
41-43, 45

28
58

28
58

28
58

28
58

28
58, 61

62
68

29
51
63

26
59

9

Remote control

1 Open the battery compartment cover

in the direction of the arrow.

2 Install the batteries as shown

below, ensuring the correct polarity.

3 Close the battery compartment.

If bright sunlight directly beams on the front of the TV.

If an obstacle is placed between the TV and the remote.

If the batteries are not installed according to their polarities.

If the batteries are weak.

Install the batteries

Use R03/AAA/UM4 batteries.

Note:

• Weak batteries can leak and severely damage the remote control transmitter. Always remove batteries if they become weak

or if the remote control is not to be used for an extended period of time.

• Do not use old or weak batteries. The remote control may not work properly with a weak voltage from such batteries. Replace

exhausted batteries with new ones. Never try to recharge normal batteries - this could cause an explosion.

• Dispose of batteries in a designated disposal area.

Warnings:

• Never throw batteries into a fire.

• Never expose batteries to excessive heat such as sunshine, fire or the like.

Distance of remote control operation

(continued)

The remote control will not work properly in the following cases:

10

I/O connections

Illustration of 26DV733G

Illustration of 19DV733G/19DV734G/ 22DV733G/

22DV734G

Note:

Before you connect other appliances:

• To avoid potentially damaging your TV, make sure all items are switched off and disconnected from the mains power when
you make the connections.

• Arrange the desired connection.

• When you have finished making the connections, reconnect the mains power to the TV and switch it back on.

Connect your aerial as shown below. Connections to other equipments is explained further on pages 80-84.
If you have problems with reception, consult a TV antenna installer.

(A) (A)

Note:

• 22DV733G, 22DV734G, and 26DV733G are used for illustration purposes.

(A) AC input: Connect one end of the supplied AC power cord into the TV’s AC input jack, and the other end to an AC 110-

240V/50-60Hz power outlet to turn on and operate the TV.

(B) AV1 (SCART) socket: For the connection of SCART cable, see pages 83-84.
(C) HEADPHONE jack: For use when inserting a headphone with a mini plug (3.5 mm).
(D) OPTICAL DIGITAL AUDIO output: Optical audio output in Dolby Digital format for connecting an external Dolby Digital

decoder, amplifier, or home theatre system with optical audio input (see page 83).

(E) AV2 (VIDEO, Audio L/R) input: Standard (composite) video and standard audio inputs plus for connecting devices with

composite video (see pages 83-84).
Note: Standard (composite) video cables carry only video information; separate audio cables are required for a complete
connection.

(F) COMPONENT input: For use when connecting devices with component video output (see page 84).
Note: Component video cables carry only video information; separate audio cables are required for complete connection.

(G) PC/HDMI 1 AUDIO input: PC audio input terminal is shared with HDMI 1 analogue audio input terminal (see pages 80-81).
(H) HDMI 1 input: High-Definition Multimedia Interface (HDMI 1) input receives digital audio and uncompressed digital video

from an HDMI device or uncompressed digital video from a DVI device. Also see (G). HDMI connection is necessary to

receive 1080p signals (see pages 80-82).

(I) PC MONITOR input (PC): For use when connecting a personal computer (see page 80).
(J) Tuner: Connect the outdoor aerial to the aerial input socket (see page 83).
(K) Bracket holes: Fix a wall mounting bracket (not supplied) here.

AC INPUT

(K)

HEAD PHONE

SCART (AV1)

OUT

DIGITAL AUDIO

TUNER

PC MONITOR

OPTICAL

COMPONENTCOMPOSITE(AV2)

INININ

PC/
HDMI 1

VIDEO

YPbPrLRLR

AUDIO

HDMI 1

AC INPUT

HEAD PHONE

SCART (AV1)

OUT

DIGITAL AUDIO

TUNER

PC MONITOR

OPTICAL

COMPONENTCOMPOSITE(AV2)

INININ

PC/
HDMI 1

VIDEO

YPbPrLRLR

AUDIO

HDMI 1

(K)

HEAD PHONE

SCART (AV1)

OUT

DIGITAL AUDIO

TUNER

PC MONITOR

OPTICAL

COMPONENTCOMPOSITE(AV2)

INININ

PC/
HDMI 1

VIDEO

YPbPrLRLR

AUDIO

HDMI 1

HEAD PHONE

SCART (AV1)

OUT

DIGITAL AUDIO

TUNER

PC MONITOR

OPTICAL

COMPONENTCOMPOSITE(AV2)

INININ

PC/
HDMI 1

VIDEO

YPbPrLRLR

AUDIO

HDMI 1

11

DVB-C function notice

DVB-C (Digital Video Broadcasting - Cable) is the DVB European consortium standard for the broadcast transmission of digital
television over cable. This system transmits an MPEG-2 or MPEG-4 family digital audio/video stream, using a QAM modulation
with channel coding.

Information for the DVB-C function

• Any function relative to the digital television (with the DVB logo) is available only within the country or area where such signals
are transmitted. Verify with the salesperson if it is possible to receive a DVB-C signal in the zone where you live.

• Even if the television conforms to the DVB-C specifications, the compatibility to future digital DVB-C transmissions is not
guaranteed.

• Some digital television functions may not be available in some countries.

• The digital reception function of this television is only effective in the countries listed in Country in the Setup menu.

Operation of DVB-C items

Instruction items marked with an asterisk in the Owner’s Manual are relevant to the DVB-C function. When they are selected, a
notice message will appear. You will be asked to download the latest firmware at Toshiba’s official website for your TV to enable
the DVB-C function. Otherwise, this function cannot be supported.

To initiate the function, you should check if the DVB-C signal is provided by your country or your service provider, and if your TV
is equipped with the latest firmware.

DVB-C items

The DVB-C features are implemented on the following sections:

• Auto setup (See pages 17-18)

• *DTV auto tuning/Setting Antenna or Cable (See pages 19-20)

• Automatic station presetting with the built-in tuner (See page 22)

• Manual TV station presetting (See pages 24-25)

12

Using the Auto Brightness Sensor

/

/

Picture

Auto Brightness Sensor Off

Reset

: Adjust

When the Auto Brightness Sensor feature is set to On, the TV will automatically optimise the backlighting levels to suit ambient
light conditions.

Press MENU SETUP or DIGITAL MENU to

1

display the Main Menu screen.
Select Picture, and then press ENTER/CH LIST

.

Press to select Auto Brightness Sensor,

2

and then press to select On or Off to confirm
your choice.

Main Menu

Picture

Sound

Channel

Setup

13

Auto setup

: Adjust

Auto Installation

Auto Tuning

Country Germany

Ant/Cable In Antenna

Energy Saving Mode Home

Menu Language

English

/

/

/

/

: Adjust

Auto Installation

Menu Language

English

Auto Tuning

Country Germany

Ant/Cable In Antenna

Energy Saving Mode Home

/

/

: Adjust

Auto Installation

Menu Language

English

Auto Tuning

Country Germany

Ant/Cable In Antenna

Energy Saving Mode Home

/

/

: Adjust

Auto Installation

Menu Language

English

Auto Tuning

Country Germany

Ant/Cable In Antenna

Energy Saving Mode Home

Your TV has an automatic installation routine which makes installation easy. When you turn on the TV for the first time, the
automatic installation routine is activated. This routine helps you select the on-screen language, antenna or cable in, country,
energy saving mode, and automatically search for and store all available analogue and digital (DVB) channels.

The automatic station presetting feature is for the TV’s built-in tuner only. If you have a device such as a digital decoder (e.g.
Satellite or Digital Terrestrial) connected (see page 83), you need to tune it in separately according to its own instructions.

Press on the TV control panel or on the

1

remote control.
The Auto Installation menu will appear.

Press to select Menu Language, and then

2

press to select your preferred language.

*

Press to select Ant/Cable In, and then

3

press to select between Antenna or Cable
for your TV.

Note:

• A DVB-C notice will appear when you switch
Antenna to Cable. Please check if this function
is supported in the place you live, and if the latest
firmware has been installed on your TV (see

DVB-C Notice on page 2 and DVB-C function
notice on page 12).

Press to select Country, and then press

4

to select your country.

14

Press to select Energy Saving Mode.

5

For normal home use, press to select

Home.

Note:

• The factory default settings of this TV meet the Energy Saving requirements. Enabling
or changing certain features and functionality (e.g. Picture Setting) may increase energy
consumption, possibly beyond the limits required for Energy Saving qualification.

To ensure your TV is operating at optimal energy efficiency, select [Home] mode during
initial activation.

• The corresponding default setting of Picture Preference to [Home] mode is “Standard”,
and the corresponding default setting of Picture Preference to [Retail] mode is “Sports”.
The Energy Saving Mode will remain the same regardless of the changes made to the
setting of Picture Preference.

• If you want to change the current energy saving mode setting, perform the Reset
procedure (see page 34) and run the auto installation routine to select a different mode.

Press to select Auto Tuning, and then press

/

Connect aerial to TV then press ENTER to
start auto tuning

EXIT : End

(Analogue)

Auto Installation

Menu Language

English

DTV Channel Found 5
Radio Channel Found

Auto Tuning

3

Energy Saving Mode Home

EXIT : Cancel

Country Germany

Ant/Cable In Antenna

(Digital)

6

ENTER/CH LIST .

A message prompt will appear with option to
connect aerial to TV.

Auto setup (continued)

Note:

• The Auto Tuning process
will only start by itself the
first time you turn on the
TV/DVD. To enable Auto
Tuning in a later time, see
page 22.

Press ENTER/CH LIST to start Auto Tuning.

7

Your TV will now automatically detect all available
channels in your area and store them in the TV’s
memory. Analogue channels will be scanned first,
and then digital channels.

When the Programming Now progress bar is
completely highlighted, the Auto Tuning process is
finished.

To cancel the Auto Tuning process:
Press EXIT/CANCEL .

Note:

• Please be patient. The Auto Tuning process can
take several minutes to complete.

Auto Installation

Menu Language

Ant/Cable In Antenna
Country Germany

Energy Saving Mode Home

Auto Tuning

Analogue Channel Found

English

16

EXIT : Cancel

15

*DTV auto tuning/Setting Antenna or Cable

/

/

/

/

/

/

/

/

/

/

: Adjust

Auto Tuning will delete all previously

stored channels -

Do you want to proceed?

Yes No

Preparations:

• Turn on the TV with the
button on its left

side.The power
indicator will light green.
To place the TV in
standby mode, press
on the remote control.
Power indicator will
change from green to red.
To turn on the TV from
standby mode, press
on the remote control
again.

In standby mode, you can
also turn the TV on with

on the TV or
CH on the remote
control.
To turn off the TV, press

button on it; to
completely switch it off,
disconnect the mains
power supply.

•Press TV/DVD to
select TV mode.

•Press ATV/DTV to
toggle between analogue
TV and digital TV mode.

Auto Tuning will completely re-tune your TV and can be used to update the channel list. It is
recommended that DTV auto tuning is run periodically to ensure new services are added. If the
setting of Ant/Cable In is changed the Auto Tuning screen will automatically appear. All current
programmes and settings will be lost.

Press INPUT to select ATV or DTV, and then press ENTER/CH LIST .

1

Press MENU SETUP in ATV (analogue TV) mode or press DIGITAL MENU in DTV

2

(digital TV) mode to display the Main Menu screen.

When DIGITAL MENU is pressed in ATV mode, it will automatically switch to DTV mode.

And it is possible to use MENU SETUP in DTV mode.

Press to select Channel, and then press

3

ENTER/CH LIST .

*

Press to select Ant/Cable In, and then press

4

to select between Antenna or Cable for your

TV.

Ant/Cable In Antenna

Country Germany

Note:

• A DVB-C notice will appear when you switch
Antenna to Cable. Please check if this function is
supported in the place you live, and if the latest
firmware has been installed on your TV (see DVB-
C Notice on page 2 and DVB-C function notice
on page 12).

A message prompt will appear warning that the previously stored channels will be lost.

Press to select Yes or No, and then press ENTER/CH LIST .

Main Menu

Picture

Sound

Channel

Setup

>>

>>

>>

: Adjust

Note:

• If no button is pressed
after approximately 60
seconds, the Main Menu
screen will disappear.

•Press EXIT/CANCEL
to exit the Main Menu

screen.

16

Note:

• If DVB-C function is unavailable, the message prompt will not appear.

Press to select Country, and then press to select your country.

5

Press to select Auto Tuning, and then press ENTER/CH LIST .

6

Setting Antenna:

(1) When Ant/Cable In is set to Antenna, a

message prompt will also appear with option to
delete previously stored channels.

Pre ss to sele ct Yes or No, and then press

ENTER/CH LIST .

*DTV auto tuning/Setting Antenna or Cable (continued)

/

(2) The auto scan process will now begin. A progress
bar appears to indicate scanning progress.

Note:

• All the channels will
be deleted before the
scanning process
begins.

• You can cancel the
scan process at any
time by pressing

EXIT/CANCEL .
The carriers and the

services stored before
EXIT/CANCEL is

pressed will be stored.

DTV Channel Found

Radio Channel Found 0

Frequency(kHz) 642000

EXIT : Cancel

*Setting Cable:

(1) When Ant/Cable In is set to Cable, a list of

setting options will be displayed.

Note:

• This setting cannot be enabled due to DVB-C
unavailability. Please check if this function is
supported in the place you live, and if the latest
firmware has been installed on your TV (see DVB-
C Notice on page 2 and DVB-C function notice on
page 12).

Auto Tuning

Scan Type Full Scan

Start Frequency Auto

End Frequency Auto

Modulation 64 QAM

Symbol Rate Auto

Network ID Auto

Start

With the exception of Scan Type and Modulation, all of the settings have two options:

- Auto: Values are pre-set by the TV’s operating system.

- Input: Allows a single value to be entered in place of the pre-set value. If no channel is

currently tuned and Input is chosen a system default value will be displayed. If a channel is
currently tuned and Input is chosen the value of the channel will be displayed.

• Scan Type: There are two options, Full Scan and Quick Scan. Quick Scan is a simplified
version of Full Scan and takes less time to complete.

• Start Frequency: This sets the frequency from which the scan will start.

• End Frequency: This sets the frequency at which the scan will stop. The valid entry range

for frequency items is 113.000-858.000 for C-Book/Other and 114.000-858.000 for Nordig-C.
If a number outside of this range is entered the value will automatically set to a minimum or
maximum valid value.

• Modulation: There are six QAM modulation settings to choose from.

•Symbol Rate: This is the Baud rate (KS/s) of the scan. The valid entry range for Symbol Rate

is 4000-7200. If a number outside of this range is entered the value will automatically set to a
minimum or maximum valid value.

•Network ID: This is the Network ID to be used for the scan. This item will be disabled and
cannot be selected when the Scan Type is set to Full Scan.The valid entry range for Network
ID is 1-65535. If a number outside of this range is entered the value will automatically set to
a minimum or maximum valid value.

(2) Press to select Start to start auto scan.

Press EXIT/CANCEL to return to the normal screen.

7

0

17

Selecting the video input source

/

ATV

DTV

AV1

AV2

Component

HDM1

HDM2

AV1

AV2

Component

HDM1

HDM2

7. PC

8. DVD

ENTER : Set

Select

Selecting the video input source

Press INPUT to view a signal from the device connected to your TV, such as a VCR or

1

DVD player.
You can select each input source according to the devices you have connected to your TV.

Press or the corresponding number on the

2

screen to select a video input source, and then
press ENTER/CH LIST within 5 seconds.

Note:

• If no button is pressed
after approximately 5
seconds, the Source
Selection menu screen
disappears.

18

Automatic station presetting with the built-in tuner

/

/

/

Country Germany

>>

>>

>>

: Adjust

/

/

EXIT : Cancel

Analogue Channel Found

0

Automatic station presetting with the built-in tuner

Perform this feature to search for and store new analogue and digital TV programmes after the
Automatic Installation (see pages 14-15).

Preparation:

Make sure your antenna is connected to the aerial input (see page 11). Select ATV or DTV (see

page 16), and then press MENU SETUP or DIGITAL MENU .

Press to select Channel, and then press ENTER/CH LIST .

1

In ATV mode:

2

(1) Press to select Country, and then press

(2) Press to select Auto Tuning, and then press ENTER/CH LIST .

(3) A message prompt will appear with option
to delete previously stored channels.
Press to select Yes or No, and then

press ENTER/CH LIST .

to select your country.

Auto Tuning will delete all previously

stored channels -

Do you want to proceed?

Yes No

: Adjust

The automatic tuning will search for available
channels and store them in a correct order.
During the search the sound is muted. When all
channels have been stored, the normal TV
screen will appear.

*In DTV mode:

Perform the steps 4-6 as detailed in DTV auto tuning/Setting Antenna or Cable on pages
16-17.

Note:

• The DVB-C function cannot be initiated when switching the setting of Ant/Cable In to
Cable. Please check if this function is supported in the place you live, and if the latest
firmware has been installed on your TV (see DVB-C Notice on page 2 and DVB-C
function notice on page 12).

19

Changing the order of stored channels

/

/

Ch Allocation

Erase Programme

Skip

Ch Label

Lock

Sort

/

/

/

/

/

/

/

/

/

Changing the order of stored channels

The Automatic station presetting stores channels in a specific order. However, this order can be
changed if you wish.

Press MENU SETUP or DIGITAL MENU to display the Main Menu screen.

1

Select Channel, and then press ENTER/CH LIST .

Press to select Ch Allocation, and then press ENTER/CH LIST .

2

Press to select a channel allocation option, and

3

then press ENTER/CH LIST .

After configuring the channel allocation options, press MENU SETUP to return to Ch

4

Allocation menu, or press EXIT/CANCEL to return to the normal screen.

Note:

• When changing the
order of channels, it is
best to start with Ch1.

There are several options to customise your channel allocation settings:

Sort

Press to select the channel that you want to move, and then press to move the channel
label to the left side of the list. Press to select the position that you want to move the channel
to, and then press to confirm the move.

Erase Programme

Press to select the channel that you want to erase, and then press

ENTER/CH LIST .

Lock

This feature enables you to lock any channel you choose by pressing ENTER/CH LIST , and
then enter the parental lock password. If you have not set the parental lock password, you can use
the initial password “0000”.

Skip

Press to select the channel that you want to skip, and then press ENTER/CH LIST . A

mark will appear.

Ch Label

• Channel Number: Press to select a channel that you want to renumber, and then press

ENTER/CH LIST . Use the number buttons 0-9 to input the number that you prefer for the

selected programme. If the number you key in has already existed, a warning message will
appear, and you should try another one.

• Ch Label: Press to select a channel that you want to rename, and then press to
select Ch Label. Press repeatedly until the character you want appears in the first place.
When the character you want appears, press ENTER/CH LIST . Repeat this step to enter the

rest of the characters.

• Label Clear: If you want to remove the channel label, press to select Label Clear, and
then press ENTER/CH LIST .

20

Manual TV station presetting

/

/

/

/

/

Colour System PAL

Sound System D/K

: Adjust

Manual Tuning

z

z

/

/

/

DTV Channel Found 5
Radio Channel Found

3

Channel List

Ch-5

Frequency(kHz) 177500

Manual Tuning

Completed

EXIT : Cancel

The Auto Tuning process stores all available stations in the reception area. However, some stations with weak or poor reception
may not be detected. If this is the case and you still want to store these stations in your TV, press the ATV/ DTV button to
enter ATV or DTV mode, and then follow the steps below.

Press MENU SETUP or DIGITAL MENU to display the Main Menu screen.

1

Press to select the Channel menu, and then press ENTER/CH LIST .

2

Press to select Manual Tuning, and then press ENTER/CH LIST .

3

In ATV mode:

4

(1) Press to select Search, and then press to start tuning. It will stop at

each station that has good reception.

(2) If you like to use fine-tuning, select Fine. Press to fine tune until the station is

adjusted to the best position (see the note on the left of this page).

Manual Tuning

z

Colour System Auto

Sound System Auto

z

Note:

• Under a normal
receiving condition, the
station search will stop
automatically at the best
receiving position. That
picture will appear
without disturbance.
This receiving position
will be automatically
saved. You do not need
to fine tune it.
In the rare case of bad
reception, the station
search might not stop at
the best receiving
position. The picture
display in that station will
appear disturbed (e.g.
wavy lines). Only in this
case will you need to
manually fine tune the
station’s position.

: Adjust

(3) To select a colour system for your TV, select Colour System. Press to select

the TV system applicable to your area: Auto, PAL or SECAM.

(4) To select a sound system, select Sound System. Press to select the sound

system applicable to your area: Auto, B/G, I, D/K or L/L’.

In DTV mode:

• When Ant/Cable In is set to Antenna, you can select a channel number for Channel
List by pressing . The corresponding tuning frequency for the channel will be set.
Or you can enter a frequency value to start tuning.

After setting the channel, press ENTER/CH LIST to start scanning for channels.
A progress bar will appear to indicate scanning progress, and a list of services collected
from the channel will be listed.

Manual Tuning

Channel List

Frequency(kHz) 177500

Ch-5

: Adjust

21

Manual TV station presetting (continued)

[0-9] : Select

Manual Tuning

Frequency(kHz) 113000

Symbol Rate 6900

Modulation 64 QAM

• *When Ant/Cable In is set to Cable, the following information will be displayed:

- Frequency(kHz): A specific frequency can be input for scanning.

- Symbol Rate: A specific baud rate (KS/s) can be input for manual scanning.

- Modulation: Select from five QAM modulation options

After setting the channel, press ENTER/CH LIST to start scanning for channels.

Note:

• This setting cannot be enabled due to DVB-C unavailability. Please check if this function is
supported in the place you live, and if the latest firmware has been installed on your TV (see
DVB-C Notice on page 2 and DVB-C function notice on page 12).

5 Press EXIT/CANCEL to return to the normal screen.

Manual Tuning

Frequency(kHz) 113000

Symbol Rate 6900

Modulation 64 QAM

DTV Channel Found 5
Radio Channel Found

3

Completed

EXIT : Cancel

22

Note:

/

DTV Channel List

Analogue Channel List

Channel List - ATV

01. Channel

02. Channel

03. Channel

04. Channel

05.

06.

07.

08.

09.

10.

11.

/

• If the built-in tuner does
not receive anything (e.g.
if no antenna is
connected) during TV
operation, the TV will
change to standby mode
after approx. 15 minutes.

•Press TV/RADIO to
switch between the three
service categories: TV,
Radio, and Data.

Basic operation

Channel selection

Use the number buttons 0-9. For example:

• CH 2: Press 0 and within 2 seconds, press 2. The TV will switch to CH 2.

• CH 29: Press 2 and within 2 seconds, press 9. The TV will switch to CH 29.

(1) Press CH to select a channel. This takes approx. 2 seconds to switch from one

channel to another. Only channels saved in the TV and are active can be displayed.
Skipped channels will not appear (see page 23).
The Channel List shows a list of all receivable programmes. They are located in channels 1
to 99 for ATV mode and 1 to 9999 for DTV mode.

(2) Press ENTER/CH LIST to display the Channel List.

Channel List Radio

S.No Service

007. SBS 6

008. SBS 7

009. SBS 8

010. SBS 9

011. SBS 10

012. SBS 11

ENTER TV/RADIO

(3) Press to select a desired channel, and then press ENTER/CH LIST to display

the selected channel.

(4) Press EXIT/CANCEL to exit.

Toggle between the list of TV, Radio, and Data services (DTV mode only)

(1) Press TV/RADIO to switch between the TV, Radio, and Data mode.

(2) If you press ENTER/CH LIST when you are in Radio mode, the Channel List menu

will display the list of Radio services.
If you wish to view the list of Data services without exiting the current menu, press

TV/RADIO once.

If you wish to view the list of TV services without exiting the current menu, press

TV/RADIO again.

QuickView

Press CH RTN ZOOM to go back to the last selected channel.

Volume adjustment

Press VOL +/– to adjust the volume. The volume level indicator shows the current volume, and
will disappear after 4 seconds of inactivity.

Mute

Press MUTE to turn off the sound. The TV/DVD’s sound will be turned off and Mute will
appear on-screen. Press MUTE again or VOL

+/– to turn the sound on.

23

Basic operation (continued)

11
BBC1

Sleep Timer

1h 40m

NICAM ST

Auto

576i

Service no.

Service name

Duration bar

Genre

Time and
Date

Lock status

Starting/Ending
time of current
programme

Parental rating

DVB Teletext available

DVB Subtitle available

Pay TV

Audio mode

Basic Service Information

Service Name: 004 bid-up.tv

81%
90%

Service ID: 0001, running
Multiplex: 40C (TSID 03ec, ONID 22f1)
Network: Crystal Place (ID 3402)
Bit Error Level: 5.165 e-02

Signal Strength

Signal Quality

No Event Name

No descreption

ENTER

EXIT

i

Information display

In ATV mode:

Press to display the channel number and sleep
timer settings information on the screen. Current
settings for the sound mode, picture size, and
resolution (if in use) are also displayed. The
information will appear for approx. 5 seconds.

In DTV mode:

When you switch channels, a channel banner is displayed for a few seconds. The channel
banner shows information such as current date and time, DTV channel number, station, and
messages from the DTV service providers, etc.

(1) While watching a programme, press to display the channel banner. The channel

banner will disappear after a set time. You can change how long the channel banner is
displayed (see page 46 for details).

Note:

• In the Basic Service
Information, the name of

channels and services
appears in full not in
abbreviation.

• Depending on the
availability of DVB-C
function, the Basic
Service Information here
may be different from that
shown on your TV.

• Subtitles are displayed on
the channel banner, but
some broadcasts may not
provide this service.

(2) Press again to display the Basic Service Information screen.

You can verify the signal strength and quality of the selected service here. If necessary,
adjust the direction of antenna to obtain the maximum signal strength.
A short event description of an event can also be viewed here. For an extended description
of an event, you can view it in the EPG menu (see page 53).

24

(3) Press to remove the display of the Basic Service Information.

Sleep timer

Press SLEEP to set the sleep timer to turn off your TV/DVD after a set length of time. Each
time you press the SLEEP button, the timer setting increases in 10 increments (Off, 0h 10m, 0h
20m, ..., 2h 0m). After the setting is programmed, the display will begin 30 seconds in advance
to remind you that the sleep timer is enabled.

To confirm the sleep timer setting, press SLEEP and the time remaining will appear for a
few seconds. To cancel the sleep timer, press the SLEEP button repeatedly until Off appears.

Teletext

TELETEXT

TELETEXT

/

/

A teletext service offers a range of text-based information, typically including news stories, sport articles, weather forecasts, and
TV schedules. Information is sent page by page. The TV can store up to 256 pages, but they can only be accessed once they
have been stored.

Fastext/TOPtext

The Fastext/TOPtext is teletext with a special directory.
On the lower part of the screen there are four different

coloured fields (red, green, yellow, and blue). These
fields lead directly to the pages shown within. The
coloured buttons on the remote control correspond to
the coloured fields. Press the appropriate coloured
button in order to activate the desired coloured field.

Switch Teletext on/off

Teletext is not available for all channels.
(1) Select a channel that shows teletext.
(2) Press . You will now see a teletext page.

(If “100” is shown without any text information, it may
mean that the current channel does not support teletext.)

(3) Press again to switch to split TV-teletext display

mode. You will now see both the teletext page and the TV

programme.
(4) Press once more to close the teletext screen.
(5) Press again in order to switch teletext on.

The last page which was stored is now shown.

Note:

• You cannot change channels when there is a teletext

display. Turn off the teletext if you want to switch to another
channel.

Select page

Press CH until the page you want appears. Or use the
number buttons 0-9 to enter the page number.

If you input the wrong page number, enter 3 random numbers
first, and then enter the number you want. Or press one of the
coloured teletext buttons, so the page from Fastext/TOPtext
will be shown.

Hold page

Some pages are divided into sub-pages by channel. Sub­pages are automatically displayed when they are transmitted.
In order to hold a page, press .

Press again to display the next sub-page.

Directly select a sub-page

Sub-page numbers are displayed below the coloured bar.
Press to select a sub-page, or highlight to display
a sub-page when it is transmitted. You can directly select a
sub-page if required.

Example:
On the screen below, page 197 offers the sub-page service.

At the bottom of the screen, sub-pages (01/02/03) available for
page 197 are displayed.

To select a sub-page:

(1) Press in order to select 01 sub-page.
(2) Press again in order to switch to 02 sub-page.
(3) Press once more to switch to 03 sub-page.

Enlargement

Press to increase the size of teletext display - either the
upper or lower half of the screen is enlarged. Each time you
press , the display toggles between half-screen and full­screen display mode.

Answering quiz questions

Some teletext pages contain quiz questions. Answers to these
questions are hidden within the page. Press to reveal the
answers.

Page 100

Press ENTER/CH LIST to show page 100 of a multi-page
teletext.

25

Stereo reception with the built-in analogue tuner

/

NICAM Auto

Bass 15

Treble 15

Balance

HDMI1 Audio HDMI

Digital Audio Output Bitstream

: Adjust

Sound

/

NICAM ST

NICAM M1

NICAM M1 / M2

NICAM OFF

Sound Sound

STEREO

The TV’s built-in tuner can detect and receive NICAM stereo broadcasts automatically.

NICAM stereo sound reception

Press MENU SETUP to display the Main Menu

1

screen.
Press to select Sound, and then press
ENTER/CH LIST .

Select NICAM, and then press to select

2

Auto or Off.
Select Off if you do not want to receive NICAM

sound.

Press EXIT/CANCEL to return to the normal screen.

3

Note:

Bad reception can cause
disturbance to stereo sound.
In some cases, NICAM
stereo sound may not be
received correctly. In the
case of two-channel sound
reception, press AUDIO
SELECT to switch to a
sound channel with better
audio quality.

The following types of broadcast are possible with NICAM transmissions:

• NICAM ST: Illuminates for approx. 4 seconds when a
NICAM STEREO broadcast signal is received.

• NICAM M1: Illuminates for approx. 4 seconds when a
NICAM MONO A broadcast signal is received.

• NICAM M1/ M2: Illuminates for approx. 4 seconds
when a NICAM MONO A and MONO B broadcast
signals are received.

• NICAM OFF: Appears for approx. 4 seconds when a
NICAM signal is received and the NICAM Off option is
selected.

Stereo reception in Germany

STEREO illuminates for approx. 4 seconds when a

STEREO broadcast signal is received

Two-channel sound reception

When two-channel sound reception is available, press AUDIO SELECT to select your
preferred audio channel.

Each time you press AUDIO SELECT , the sound channel will switch between the two
alternative channels available.

NICAM two-channel sound reception (not available in Germany)

Two-channel sound reception in Germany

26

Picture format

The broadcaster may transmit a widescreen signaling (WSS) signal which can determine the correct height/width of pictures
and have it set automatically when the setting Auto is selected. If you want to change this setting, you can select from the
formats listed below.

Note:

• When the picture size is set to Auto
mode, the aspect ratio will
automatically change according to
the WSS signal, if it is available.
This may either be transmitted by a
broadcasting TV channel, or via a
recording from a VCR, etc. Any
WSS signal received will only be
effective in Auto mode. However,
some DVD players/digital decoders
etc. will automatically switch the
aspect ratio via a SCART input (Pin
8 switching), even if Auto is not
selected.
In any case, if you want to change
an aspect ratio to the one selected
automatically, you can change it by
pressing PIC SIZE .

• In PC mode, the picture size
settings is available only for
16:9 or 4:3 format.

• In HDMI or Component mode, the
scanning rates are 720p and 1080i,
and the picture size settings is
available only for 16:9 or Real
(HDMI mode only) format.

• Using the PIC SIZE function to
change the format of the displayed
image (i.e. changing the height/
width ratio) for the purposes of
public display or commercial gain
may infringe on copyright laws.

Auto picture size

Press PIC SIZE repeatedly until Auto appears on the screen.

Picture format setting

Press PIC SIZE repeatedly to scroll through the following options.

4:3

This mode shows a picture in the standard 4:3 format with vertical black bands on the
left and right sides.

Real (HDMI mode only)

The picture is displayed in its original size.

16:9

This mode is used with 16:9 signals from a Digital decoder, DVD player or other
external source. This uniformly stretches a 4:3 picture horizontally to fill the screen.
(For example, DVDs often store a 16:9 image ‘‘anamorphically’’, which means that the
16:9 image is stored as a horizontally compressed 4:3 image. Select the 16:9 format
to restore the image to its proper 16:9 proportions.)

Cinema

This mode is used to zoom in, or expand pictures with a 4:3 ‘‘letterbox’’ format (with
black bars on the top and bottom of the picture) so that they fill more of the screen.

Note:

• Using this format will slightly cut off part of the picture due to the image expansion.
However, it is possible to scroll the picture up or down to view the cutoff section on
the top or bottom part of the picture (see Vertical Position on page 33).

14:9

This mode enlarges a standard 4:3 picture to the 14:9 format.

27

AV colour adjustment

ATV

DTV

AV1

AV2

Component

HDM1

HDM2

/

Display Setup

Auto 4:3 Default

4:3

Auto Shut Off

AV Colour Auto

: Adjust

>>

>>

Vertical Position 0

/

/

Use the AV Colour menu option to adjust the picture colour settings in AV mode. These settings do not apply when the TV is
in any other mode.

Note:

• DVD players that play
NTSC DVDs (i.e. multi­region/region code-free)
can produce different
signals based on the
player model. Possible
signals include PAL,
SECAM, NTSC3.58,
NTSC4.43 and PAL60. If
you are using an external
DVD player, connect it to
the TV through the
component video jack.

Press INPUT to select AV1 or AV2 , and then

1

press ENTER/CH LIST .

Press MENU SETUP or DIGITAL MENU to display the Main Menu screen.

2

Press to select Setup, and then press ENTER/CH LIST .

3

Press to select AV Colo u r, and then press

4

to select the preferred colour system.
Options include PAL, SECAM, NTSC4.43,
NTSC3.58, and PAL6 0.

If you are not certain of the system used in your
area or if the setting you have selected causes
horizontal stripes to the picture display, select
Auto.

Press EXIT/CANCEL to return to the normal screen.

5

28