Main Connections (For UK only)
CAUTION:
For UK Only
CONNECT THE MAIN LEAD INTO A MAINS POWER SOCKET
POWER SUPPLY 230V. It must not be connected to D.C. mains.
Note: The mains lead of the set is fitted with a moulded plug. If the mains socket are not compatible or if for any reason the plug is removed please follow the directions below. The moulded plug cannot be rewired and if removed must be disposed of safely.
DO NOT under any circumstances plug the severed plug into any mains socket as this could result in electric shock.
Important: If the plug is removed, rewire the new plug as follow:
The wires in the mains plug are coloured in accordance to the following code:
BLUE = NEUTRAL & BROWN = LIVE
If the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:
BLUE wire to the terminal coded N (Neutral) or coloured black.
BROWN wire to the terminal coded L (Live) or coloured red.
DO NOT make any connection to
the terminal in the plug which is marked by the letter E or by the earth symbol or coloured green
or green and yellow.
A fused plug must be fitted with a 3A fuse approved by ASTA or BS1362 and fuse covers must be always be securely replaced. If your set does not work, the fuse may be blown.
MAINS CONNECTIONS:
(For UK, see inside front cover)
MAINS OUTLET POWER SUPPLY: 230V ~50Hz
Note:
Power is fed to the unit even when it is not functioning. To cut the power supply off, the power cable must be unplugged.
RR60 EN |
1 |
9/10/02, 5:28 PM |
Safety Information |
|
|||
TECHNICAL SPECIFICATIONS: |
EN |
|||
Power supply |
||||
|
||||
AC 230V ~50Hz |
|
|||
Clock:9V |
|
6F22 |
|
|
|
|
Power consumption: 4W
Please respect the environment. Before throwing any batteries away, consult your distributor who may be able to take them back for specific recycling.
Do not place the system near wet areas such as bathrooms and pool side.
Do not expose this appliance to rain or moisture Avoid storing the system at humid places or near abnormally heated areas.
Power is continuously supplied to the system. To disconnect power completely, unplug the power cord from the power outlet.
Do not expose this appliance to dripping and splashing.
|
|
|
CAUTION |
|
|
|
|
RISK OF ELECTRIC SHOCK |
|
|
|
|
DO NOT OPEN |
|
T H E L I G H T N I N G |
CAUTION: TO REDUCE THE |
|||
FLASH AND ARROW- |
RISK OF ELECTRIC SHOCK, |
|||
HEAD WITHIN THE |
DO NOT REMOVE COVER |
|||
T R I A N G L E I S A |
( O R B A C K ) . N O U S E R - |
|||
WA R N I N G |
S I G N |
SERVICEABLE PARTS IN - |
||
ALERTING |
YOU OF |
S I D E . R E F E R S E RV I C I N G |
||
" D A N G E R O U S |
TO Q UA L I F I E D S E RV I C E |
|||
VOLTAGE" |
INSIDE |
PERSONNEL. |
||
THE PRODUCT. |
|
|
|
THE EXCLAMATION POINT WITHIN THE T R I A N G L E I S A WARNING SIGN ALERTING YOU OF I M P O R T A N T I N S T R U C T I O N S A C C O M PA N Y I N G T H E P R O D U C T.
SEE MARKING ON BOTTOM / BACK OF PRODUCT
WARNING:TO PREVENT FIRE OR ELECTRICAL
SHOCK HAZARD, DO NOT EXPOSETHIS PRODUCT
TO RAIN OR MOISTURE.
1
RR60 EN |
2 |
9/10/02, 5:28 PM |
Battery Back-Up Operation
EN |
This clock radio is equipped with a memory |
|
holding system that is powered with a 9- |
|
volt battery (not included). The power |
|
failure protection circuit will not operate |
|
unless battery is installed. |
|
When normal household power is inter- |
|
rupted, or AC line cord is unplugged, the |
|
battery will power the clock radio to keep |
|
track of time and alarm settings pro- |
|
grammed into memory. When the battery |
|
backup functions, the digital display will |
|
not light, however, the function of alarm |
|
still occurs during the power interruption. |
|
Normal operation will resume after AC |
|
power is restored so you will not have to |
|
reset the time or the alarm. |
Install battery as follows:
1.Remove battery compartment door (located at the bottom of the radio) by applying thumb pressure to area indicated on battery door and then lift the door out and off the cabinet.
2.Connect a 9-volt battery to the connector plug.
3.Insert battery in the compartment and replace the compartment door.
Power Failure Indicator
When AC power is interrupted (disconnected) for a short period of time, both time and alarm settings will change (unless optional battery is installed). After AC power is restored (reconnected), the Digital Display will blink to indicate that power was interrupted and you should readjust the time and alarm settings.
Note: Alkaline (NEDA 1604A / IEC 6LR61) battery is recommended. Carbon Zinc (NEDA 1604 / IEC 6F22) battery may be used but memory holding time will be substan-
tially reduced. Memory holding time for a fresh alkaline battery is approximately 8 hours (if radio or alarm is not operated), which should take care of short, nuisance-type AC power failures. To preserve battery life, the radio should remain plugged into an AC outlet. As batteries get older, their voltage drops and memory may be lost. Be sure to replace the battery periodically. Battery should be removed if the radio will be stored for more than one month. Leaky batteries may badly damage the clock radio.
2
RR60 EN |
3 |
9/10/02, 5:28 PM |