TEXAS INSTRUMENTS TPS7201Q, TPS7225Q, TPS7230Q, TPS7233Q, TPS7248Q Technical data
...
TPS7201Q, TPS7225Q, TPS7230Q
TPS7233Q, TPS7248Q, TPS7250Q, TPS72xxY
MICROPOWER LOW-DROPOUT (LDO) VOLTAGE REGULATORS
SLVS102G – MARCH 1995 – REVISED JUNE 2000
D
Available in 5-V, 4.85-V, 3.3-V, 3.0-V, and
2.5-V Fixed-Output and Adjustable Versions
D
Dropout Voltage <85 mV Max at
IO = 100 mA (TPS7250)
D
Low Quiescent Current, Independent of
Load, 180 µA Typ
D
8-Pin SOIC and 8-Pin TSSOP Package
D
Output Regulated to ±2% Over Full
Operating Range for Fixed-Output Versions
D
Extremely Low Sleep-State Current,
SENSE†/FB
RESET/PG
†
SENSE – Fixed voltage options only
(TPS7225, TPS7230, TPS7233, TPS7248,
and TPS7250)
‡
FB – Adjustable version only (TPS7201)
D, P, OR PW PACKAGE
(TOP VIEW)
‡
GND
EN
1
2
3
4
8
7
6
5
OUT
OUT
IN
IN
0.5 µA Max
D
Power-Good (PG) Status Output
description
600
TA = 25°C
500
The TPS72xx family of low-dropout (LDO) voltage
regulators offers the benefits of low-dropout
voltage, micropower operation, and miniaturized
400
TPS7225
TPS7230
packaging. These regulators feature extremely
low dropout voltages and quiescent currents
300
compared to conventional LDO regulators.
Offered in small-outline integrated-circuit (SOIC)
packages and 8-terminal thin shrink small-outline
(TSSOP), the TPS72xx series devices are ideal
for cost-sensitive designs and for designs where
board space is at a premium.
200
– Dropout Voltage – mV
DO
V
100
TPS7250
TPS7248
A combination of new circuit design and process
innovation has enabled the usual pnp pass
transistor to be replaced by a PMOS device.
0
0 50 100 150
IO – Output Current – mA
Because the PMOS pass element behaves as a
low-value resistor, the dropout voltage is very low
– maximum of 85 mV at 100 mA of load current
Figure 1. Typical Dropout Voltage Versus
Output Current
(TPS7250) – and is directly proportional to the
load current (see Figure 1). Since the PMOS pass
element is a voltage-driven device, the quiescent current is very low (300 µA maximum) and is stable over the
entire range of output load current (0 mA to 250 mA). Intended for use in portable systems such as laptops and
cellular phones, the low-dropout voltage and micropower operation result in a significant increase in system
battery operating life.
TPS7233
200 250
The TPS72xx also features a logic-enabled sleep mode to shut down the regulator, reducing quiescent current
to 0.5 µA maximum at T
= 25°C. Other features include a power-good function that reports low output voltage
J
and may be used to implement a power-on reset or a low-battery indicator.
The TPS72xx is offered in 2.5-V , 3-V , 3.3-V , 4.85-V, and 5-V fixed-voltage versions and in an adjustable version
(programmable over the range of 1.2 V to 9.75 V). Output voltage tolerance is specified as a maximum of 2%
over line, load, and temperature ranges (3% for adjustable version).
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
Copyright 2000, Texas Instruments Incorporated
1
TPS7201Q, TPS7225Q, TPS7230Q
T
TPS7233Q, TPS7248Q, TPS7250Q, TPS72xxY
MICROPOWER LOW-DROPOUT (LDO) VOLTAGE REGULATORS
SLVS102G – MARCH 1995 – REVISED JUNE 2000
AVAILABLE OPTIONS
OUTPUT VOLTAGE
J
–55°C to 150°C
The D package is available taped and reeled. Add R suffix to device type (e.g., TPS7250QDR). The PW package is only available left-end
taped and reeled. The TPS7201Q is programmable using an external resistor divider (see application information). The chip form is tested
at 25°C.
(V)
MIN TYP MAX
4.9 5 5.1 TPS7250QD TPS7250QP TPS7250QPWR TPS7250Y
4.75 4.85 4.95 TPS7248QD TPS7248QP TPS7248QPWR TPS7248Y
3.23 3.3 3.37 TPS7233QD TPS7233QP TPS7233QPWR TPS7233Y
2.94 3 3.06 TPS7230QD TPS7230QP TPS7230QPWR TPS7230Y
2.45 2.5 2.55 TPS7225QD TPS7225QP TPS7225QPWR TPS7225Y
Adjustable
1.2 V to 9.75 V
SMALL OUTLINE
(D)
TPS7201QD TPS7201QP TPS7201QPWR TPS7201Y
PACKAGED DEVICES
TPS72xx
‡
PDIP
(P)
TSSOP
(PW)
CHIP FORM
(Y)
V
I
0.1 µF
‡
TPS7225Q, TPS7230Q, TPS7233Q, TPS7248Q, TPS7250Q (fixed-voltage
options)
NOTE A: Capacitor selection is nontrivial. See application information section
for details.
5
IN
6
4
IN
EN
SENSE
GND
3
PG
OUT
OUT
2
1
7
8
PG
250 kΩ
V
O
C
O
(see Note A)
+
10 µF
CSR = 1 Ω
Figure 2. Typical Application Configuration
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS7201Q, TPS7225Q, TPS7230Q
TPS7233Q, TPS7248Q, TPS7250Q, TPS72xxY
MICROPOWER LOW-DROPOUT (LDO) VOLTAGE REGULATORS
SLVS102G – MARCH 1995 – REVISED JUNE 2000
TPS72xx chip information
These chips, when properly assembled, display characteristics similar to the TPS72xxQ. Thermal compression
or ultrasonic bonding may be used on the doped aluminum bonding pads. The chips may be mounted with
conductive epoxy or a gold-silicon preform.
BONDING PAD ASSIGNMENTS
7
(7)
57
1
(1)
(2)
(6)
6
2
functional block diagram
(5)
5
69
(4)
4
(5)
(3)
IN
(2)
EN
CHIP THICKNESS: 15 MILS TYPICAL
BONDING PADS: 4 × 4 MILS MINIMUM
TJmax = 150°C
TOLERANCES ARE ±10%.
ALL DIMENSIONS ARE IN MILS.
†
Fixed-voltage options only (TPS7225, TPS7230,
3
(3)
TPS7233, TPS7248, and TPS7250)
‡
Adjustable version only (TPS7201)
NOTE A. For most applications, OUT and SENSE should
be tied together as close as possible to the device;
for other implementations, refer to the SENSE-pin
connection discussion in the application
information section of this data sheet.
TPS72xx
(1)
GND
(6)
(4)
(7)
SENSE
ĕ
FB
OUT
PG
Ĕ
IN
_
+
§
1.12 V
GND
low (active).
+
_
EN
V
= 1.188 V
ref
§
Switch positions are shown with EN
¶
For most applications, SENSE should be externally connected to OUT as close as possible to the device.
For other implementations, refer to the SENSE-pin connection discussion in application information section.
§§
PG
OUT
SENSE¶/FB
R1
R2
RESISTOR DIVIDER OPTIONS
DEVICE
TPS7201
TPS7225
TPS7230
TPS7233
TPS7248
TPS7250
NOTE A: Resistors are nominal values only.
0
257
357
420
726
756
COMPONENT COUNT
MOS transistors
Bilpolar transistors
Diodes
Capacitors
Resistors
∞
233
233
233
233
233
UNITR1 R2
Ω
kΩ
kΩ
kΩ
kΩ
kΩ
108
41
4
15
75
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
3
TPS7201Q, TPS7225Q, TPS7230Q
PACKAGE
A
PPW1175 mW
8.74 mW/°C
782 mW
650 mW
301 mW
PACKAGE
C
PPW2738 mW
20.49 mW/°C
1816 mW
1508 mW
689 mW
TPS7233Q, TPS7248Q, TPS7250Q, TPS72xxY
MICROPOWER LOW-DROPOUT (LDO) VOLTAGE REGULATORS
SLVS102G – MARCH 1995 – REVISED JUNE 2000
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Input voltage rangeĕ, VI, PG, SENSE, EN –0.3 V to 11 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output current, IO 1.5 A. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Continuous total power dissipation See Dissipation Rating Tables 1 and 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating virtual junction temperature range, T
Storage temperature range, T
–65°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
stg
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds 260°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
‡
All voltage values are with respect to network ground terminal.
DISSIPATION RATING TABLE 1 – FREE-AIR TEMPERA TURE (see Note 1 and Figure 3)
T
≤ 25°C DERATING FACTOR T
POWER RATING ABOVE TA = 25°CAPOWER RATINGAPOWER RATINGAPOWER RATING
D
D
NOTE 1: Dissipation rating tables and figures are provided for maintenance of junction temperature at or below absolute
maximum of 150°C. For guidelines on maintaining junction temperature within the recommended operating range,
see application information section.
725 mW
525 mW
DISSIPATION RATING TABLE 2 – CASE TEMPERA TURE (see Note 1 and Figure 4)
T
≤ 25°C DERATING FACTOR T
POWER RATING ABOVE TC = 25°CCPOWER RATINGCPOWER RATINGCPOWER RATING
2063 mW
2900 mW
5.8 mW/°C
4.2 mW/°C
16.5 mW/°C
23.2 mW/°C
–55°C to 150°C. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
J
= 70°C T
464 mW
°
336 mW
= 70°C T
1320 mW
°
1856 mW
= 85°C T
377 mW
273 mW
= 85°C T
1073 mW
1508 mW
= 125°C
145 mW
105 mW
= 125°C
413 mW
580 mW
Ĕ
MAXIMUM CONTINUOUS DISSIPATION
vs
FREE-AIR TEMPERATURE
1200
1100
1000
900
800
700
600
500
400
300
200
– Maximum Continuous Dissipation – mW
D
100
P
0
25 50 75 100
P Package
R
= 114.4°C/W
θJA
D Package
R
PW Package
R
= 238°C/W
θJA
TA – Free-Air Temperature – °C
θJA
Figure 3
= 172°C/W
125 150
MAXIMUM CONTINUOUS DISSIPATION
vs
CASE TEMPERATURE
3000
2500
2000
1500
1000
500
– Maximum Continuous Dissipation – mW
D
P
0
25 50 75 100
P Package
R
= 48.8°C/W
θJC
PW Package
R
= 43.1°C/W
θJC
D Package
R
= 60.6°C/W
θJC
TC – Case Temperature – °C
Figure 4
125 150
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
Input voltage, V
†
V
TPS7201Q, TPS7225Q, TPS7230Q
TPS7233Q, TPS7248Q, TPS7250Q, TPS72xxY
MICROPOWER LOW-DROPOUT (LDO) VOLTAGE REGULATORS
SLVS102G – MARCH 1995 – REVISED JUNE 2000
recommended operating conditions
MIN MAX UNIT
TPS7201Q 3 10
TPS7225Q 3.65 10
p
High-level input voltage at EN, V
Low-level input voltage at EN, V
Output current, I
Operating virtual junction temperature, T
†
Minimum input voltage defined in the recommended operating conditions is the maximum specified output voltage plus dropout voltage at the
maximum specified load range. Since dropout voltage is a function of output current,
calculate the minimum input voltage for the maximum load current used in a given application, use the following equation:
V
Because the TPS7201 is programmable, r
calculating VDO from r
lower limit for the recommended input-voltage range for the TPS7201.
I(min)
+
I
O
V
O(max)
DS(on)
IH
IL
J
)
V
DO(max load)
is given in Note 3 under the TPS7201 electrical characteristics table. The minimum value of 3 V is the absolute
DS(on)
TPS7230Q 3.96 10
TPS7233Q 3.98 10
TPS7248Q 5.24 10
TPS7250Q 5.41 10
2 V
0.5 V
0 250 mA
–40 125 °C
the usable range can be extended for lighter loads
should be used to calculate VDO before applying the above equation. The equation for
. To
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
5
TPS7201Q, TPS7225Q, TPS7230Q
PARAMETER
TEST CONDITIONS
‡
T
UNIT
,
,
Ground current (active mode)
EN ≤ 0.5 V,
V
I
V
O
V,
A
Input current (standby mode)
EN
V
3 V ≤ V
V
A
Output current limit threshold
V
0 V
V
10 V
A
g
EN
V
3 V ≤ V
≤ 10 V
A
PG leak
t
V
Normal operation
A
EN logic high (standb
)
40°C to 125°C
V
EN logic l
)
3 V ≤ V
V
V
EN i
t
0 V ≤ V
≤ 10 V
A
Minimum V
for active pass element
V
Minimum V
for valid PG
I
300 µA
V
TPS7233Q, TPS7248Q, TPS7250Q, TPS72xxY
MICROPOWER LOW-DROPOUT (LDO) VOLTAGE REGULATORS
SLVS102G – MARCH 1995 – REVISED JUNE 2000
electrical characteristics, IO = 10 mA, EN = 0 V , CO = 4.7 µF (CSR† = 1 Ω), SENSE/FB shorted to OUT
(unless otherwise noted)
J
EN ≤ 0.5 V
0 mA ≤ IO ≤ 250 mA
p
p
Pass-element leakage current in
standby mode
age curren
Output voltage temperature coefficient –40°C to 125°C 31 75 ppm/°C
Thermal shutdown junction temperature 165 °C
y mode
ow (active mode
EN hysteresis voltage 25°C 50 mV
nput curren
I
I
†
CSR(compensation series resistance) refers to the total series resistance, including the equivalent series resistance (ESR) of the capacitor, any
series resistance added externally, and PWB trace resistance to CO.
‡
Pulse-testing techniques are used to maintain virtual junction temperature as close as possible to ambient temperature; thermal effects must
be taken into account separately.
p
=
,
I
=
O
=
,
I
= 10 V,
PG
3 V ≤ VI ≤ 6 V
6 V ≤ VI ≤ 10 V
≤ 10
I
I
=
PG
V
= V
+ 1 V
+ 1
≤ 10
I
=
I
I
p
25°C 180 225
–40°C to 125°C 325
25°C 0.5
–40°C to 125°C 1
25°C 0.6 1
–40°C to 125°C 1.5
25°C 0.5
–40°C to 125°C 1
25°C 0.5
–40°C to 125°C 0.5
°
–
–40°C to 125°C 0.5
–40°C to 125°C –0.5 0.5
–40°C to 125°C 2.5
–40°C to 125°C 1.9
°
25°C 0.5
25°C –0.5 0.5
25°C 1.9 2.5
25°C 1.1 1.5
TPS72xxQ
MIN TYP MAX
µ
µ
µ
µ
2
2.7
µ
6
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PARAMETER
TEST CONDITIONS
‡
T
UNIT
g(
V
2.9 V
50 µA ≤ I
≤ 250 mA
Ω
Input regulation
I
,
µ
O
,
mV
O
,
I
,
Output regulation
mV
O
µ ,
I
,
I
A
Ripple rejection
f
120 H
dB
O
,
†
CSR
†
Ω
PG
¶
I
400 µA
V
V
V
FB input current
nA
TPS7201Q, TPS7225Q, TPS7230Q
TPS7233Q, TPS7248Q, TPS7250Q, TPS72xxY
MICROPOWER LOW-DROPOUT (LDO) VOLTAGE REGULATORS
SLVS102G – MARCH 1995 – REVISED JUNE 2000
TPS7201Q electrical characteristics, IO = 10 mA, V
= 3.5 V, EN = 0 V, CO = 4.7 µF (CSR† = 1 Ω), FB
I
shorted to OUT at device leads (unless otherwise noted)
J
Reference voltage (measured
at FB with OUT connected to
FB)
Reference voltage
temperature coefficient
Pass-element series
resistance (see Note 3)
p
p
pp
Output noise spectral density f = 120 Hz 25°C 2
Output noise voltage
PG trip-threshold voltage
PG hysteresis voltage
p
output low voltage
p
†
CSR refers to the total series resistance, including the ESR of the capacitor, any series resistance added externally, and PWB trace resistance
to CO.
‡
Pulse-testing techniques are used to maintain virtual junction temperature as close as possible to ambient temperature; thermal effects must
be taken into account separately.
§
This voltage is not recommended.
¶
Output voltage programmed to 2.5 V with closed-loop configuration (see application information).
NOTES: 2. When VI < 2.9 V and IO > 100 mA simultaneously, pass element r
dropout voltage prevents the regulator from maintaining the specified tolerance range.
3. To calculate dropout voltage, use equation:
r
DS(on)
5.9 V , which corresponds to dropout conditions for programmed output voltages of 2.5 V, 3 V , 4 V, and 6 V, respectively. For other
programmed values, refer to Figures 10 and 11.
¶
¶
VDO = IO
is a function of both output current and input voltage. The parametric table lists r
VI = 3.5 V, IO = 10 mA 25°C 1.188 V
3 V ≤ VI ≤ 10 V,
See Note 2
VI = 2.4 V,
VI = 2.4 V,
I
VI = 3.9 V, 50 µA ≤ IO ≤ 250 mA 25°C 1
VI = 5.9 V, 50 µA ≤ IO ≤ 250 mA 25°C 0.8
V
See Note 2
I
See Note 2
I
See Note 2
=
10 Hz ≤ f ≤ 100 kHz,
VFB voltage decreasing from above V
Measured at V
PG
⋅ r
DS(on)
§
§
,
=
= 3 V to 10 V, 50 µA ≤ I
= 5 mA to 250 mA, 3 V ≤ V
= 50 µA to 250 mA, 3 V ≤ V
z
= 1
FB
=
,
5 mA ≤ IO ≤ 250 mA,
50 µA ≤ IO ≤ 100 mA 25°C 2.1
100 mA ≤ IO ≤ 200 mA 25°C 2.9
O
≤ 250 mA,
≤ 10 V,
≤ 10 V,
= 50 µ
O
I
= 250 mA,
See Note 2
CO = 4.7 µF 25°C 235
CO = 10 µF 25°C 190
CO = 100 µF 25°C 125
PG
= 2.13
I
–40°C to 125°C 1.152 1.224 V
–40°C to 125°C 31 75 ppm/°C
25°C 1.6 2.7
–40°C to 125°C 4.5
25°C 23
–40°C to 125°C 36
25°C 15 25
–40°C to 125°C 36
25°C 17 27
–40°C to 125°C 43
25°C 49 60
–40°C to 125°C 32
25°C 45 50
–40°C to 125°C 30
–40°C to 125°C
25°C 12 mV
25°C 0.1 0.4
–40°C to 125°C 0.4
25°C –10 0.1 10
–40°C to 125°C –20 20
increases (see Figure 10) to a point such that the resulting
DS(on)
TPS7201Q
MIN TYP MAX
0.95 ×
V
FB(nom)
for VI = 2.4 V, 2.9 V, 3.9 V, and
DS(on)
µV/√Hz
µVrms
V
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
7
TPS7201Q, TPS7225Q, TPS7230Q
PARAMETER
TEST CONDITIONS
‡
T
UNIT
Output voltage
V
D
I
250 mA
V
V
Pass-element series resistance
(
O)O
,
I
,
Ω
Input regulation
V
3.5 V to 10 V
50 µA ≤ I
≤ 250 mA
mV
I
250 mA
V
V
Output regulation
mV
I
50 µA to 250 mA
V
≤ 10 V
I
50 µA
Ripple rejection
f
120 H
dB
I
250 mA
CSR
†
Ω
PG output low voltage
I
V
V
V
TPS7233Q, TPS7248Q, TPS7250Q, TPS72xxY
MICROPOWER LOW-DROPOUT (LDO) VOLTAGE REGULATORS
SLVS102G – MARCH 1995 – REVISED JUNE 2000
TPS7225Q electrical characteristics, IO = 10 mA, V
= 3.5 V , EN = 0 V , CO = 4.7 µF (CSR† = 1 Ω), SENSE
I
shorted to OUT (unless otherwise noted)
J
p
ropout voltage
p
p
pp
Output noise spectral density f = 120 Hz 25°C 2
Output noise voltage
PG trip-threshold voltage
PG hysteresis voltage
p
†
CSR refers to the total series resistance, including the ESR of the capacitor, any series resistance added externally, and PWB trace resistance
to CO.
‡
Pulse-testing techniques are used to maintain virtual junction temperature as close as possible to ambient temperature; thermal effects must
be taken into account separately.
VI = 3.5 V, IO = 10 mA 25°C 2.5
3.5 V ≤ VI ≤ 10 V, 5 mA ≤ IO ≤ 250 mA –40°C to 125°C 2.45 2.55
=
O
(2.97 V – V
IO = 250 mA
=
I
= 5 mA to
O
=
O
=
10 Hz ≤ f ≤ 100 kHz,
VO voltage decreasing from above V
= 1.2 mA,
PG
†
= 1
=
,
)/I
, V
,
z
= 2.97
I
= 2.97 V,
,3.5 V ≤
,3.5 V ≤
=
O
=
O
CO = 4.7 µF
CO = 10 µF
CO = 100 µF
= 2.13
I
O
I
I
≤ 10
PG
25°C 560 850 mV
–40°C to 125°C 1.1 V
25°C 2.24 3.4
–40°C to 125°C 3.84
25°C 9 27
–40°C to 125°C 33
25°C 28 36
–40°C to 125°C 60
25°C 24 41
–40°C to 125°C 73
25°C 47 58
–40°C to 125°C 45
25°C 40 46
–40°C to 125°C 38
25°C 248
25°C 200
25°C 130
–40°C to 125°C
25°C 50 mV
25°C 0.3 0.44
–40°C to 125°C 0.5
TPS7225Q
MIN TYP MAX
0.95 ×
V
O(nom)
µV/√Hz
µVrms
V
8
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PARAMETER
TEST CONDITIONS
‡
T
UNIT
Output voltage
V
I
100 mA
V
V
D
mV
I
250 mA
V
2.97 V
Pass-element series resistance
(
O)O
,
I
,
Ω
Input regulation
V
50 µA ≤ I
250 mA
mV
I
5 mA to 250 mA
V
≤ 10 V
Output regulation
mV
I
50 µA to 250 mA
V
≤ 10 V
I
A
Ripple rejection
f
120 H
dB
I
250 mA
CSR
†
Ω
PG output low voltage
I
1.2 mA
V
2.55 V
V
TPS7201Q, TPS7225Q, TPS7230Q
TPS7233Q, TPS7248Q, TPS7250Q, TPS72xxY
MICROPOWER LOW-DROPOUT (LDO) VOLTAGE REGULATORS
SLVS102G – MARCH 1995 – REVISED JUNE 2000
TPS7230Q electrical characteristics, IO = 10 mA, V
= 4 V , EN = 0 V , CO = 4.7 µF (CSR† = 1 Ω), SENSE
I
shorted to OUT (unless otherwise noted)
J
p
ropout voltage
p
p
pp
Output noise spectral density f = 120 Hz 25°C 2 µV/√Hz
Output noise voltage
PG trip-threshold voltage
PG hysteresis voltage
p
†
CSR refers to the total series resistance, including the ESR of the capacitor, any series resistance added externally, and PWB trace resistance
to CO.
‡
Pulse-testing techniques are used to maintain virtual junction temperature as close as possible to ambient temperature; thermal effects must
be taken into account separately.
VI = 4 V, IO = 10 mA 25°C 3
4 V ≤VI ≤ 10 V, 5 mA ≤ IO ≤ 250 mA –40°C to 125°C 2.94 3.06
=
O
=
O
(2.97 V – V
IO = 250 mA
= 4 V to 10 V,
I
=
O
=
O
=
10 Hz ≤ f ≤ 100 kHz,
VO voltage decreasing from above V
=
PG
†
= 1
=
z
,
,
)/I
,
, V
,4 V ≤
,4 V ≤
= 2.97
I
=
I
= 2.97 V,
O
I
I
= 50 µ
O
=
O
CO = 4.7 µF
CO = 10 µF
CO = 100 µF
=
I
≤
PG
25°C 145 185
–40°C to 125°C 270
25°C 390 502
–40°C to 125°C 900
25°C 1.56 2.01
–40°C to 125°C 3.6
25°C 9 27
–40°C to 125°C 33
25°C 34 45
–40°C to 125°C 74
25°C 42 60
–40°C to 125°C 98
25°C 45 56
–40°C to 125°C 44
25°C 40 45
–40°C to 125°C 38
25°C 256
25°C 206
25°C 132
–40°C to 125°C
25°C 50 mV
25°C 0.25 0.44
–40°C to 125°C 0.44
TPS7230Q
MIN TYP MAX
0.95 ×
V
O(nom)
µVrms
V
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
9
TPS7201Q, TPS7225Q, TPS7230Q
PARAMETER
TEST CONDITIONS
‡
T
UNIT
Output voltage
V
I
V
V
D
I
100 mA
V
3.23 V
mV
I
250 mA
V
3.23 V
Pass-element series resistance
(
O)O
,
I
,
Ω
Input regulation
V
4.3 V to 10 V
50 µA ≤ I
≤ 250 mA
mV
I
5 mA to 250 mA
V
≤ 10 V
Output regulation
mV
I
250 mA
V
V
I
A
Ripple rejection
f
120 H
dB
I
250 mA
CSR
†
Ω
PG output low voltage
I
V
V
V
TPS7233Q, TPS7248Q, TPS7250Q, TPS72xxY
MICROPOWER LOW-DROPOUT (LDO) VOLTAGE REGULATORS
SLVS102G – MARCH 1995 – REVISED JUNE 2000
TPS7233Q electrical characteristics, IO = 10 mA, V
= 4.3 V , EN = 0 V , CO = 4.7 µF (CSR† = 1 Ω), SENSE
I
shorted to OUT (unless otherwise noted)
J
p
ropout voltage
p
p
pp
Output noise spectral density f = 120 Hz 25°C 2
Output noise voltage
PG trip-threshold voltage
PG hysteresis voltage
p
†
CSR refers to the total series resistance, including the ESR of the capacitor, any series resistance added externally, and PWB trace resistance
to CO.
‡
Pulse-testing techniques are used to maintain virtual junction temperature as close as possible to ambient temperature; thermal effects must
be taken into account separately.
VI = 4.3 V, IO = 10 mA 25°C 3.3
4.3 V ≤ VI ≤ 10 V, 5 mA ≤ IO ≤ 250 mA –40°C to 125°C 3.23 3.37
= 10 mA,
O
†
=
= 1
,
,
)/I
, V
,
z
=
O
=
O
(3.23 V – V
IO = 250 mA
=
I
=
O
= 50 µA to
O
=
10 Hz ≤ f ≤ 100 kHz,
VO voltage decreasing from above V
= 1.2 mA,
PG
= 3.23
I
=
I
=
I
= 3.23 V,
,4.3 V ≤
,4.3 V ≤
= 50 µ
O
=
O
CO = 4.7 µF
CO = 10 µF
CO = 100 µF
= 2.8
I
O
I
I
≤ 10
PG
25°C 14 20
–40°C to 125°C 30
25°C 140 180
–40°C to 125°C 232
25°C 360 460
–40°C to 125°C 610
25°C 1.5 1.84
–40°C to 125°C 2.5
25°C 8 25
–40°C to 125°C 33
25°C 32 42
–40°C to 125°C 71
25°C 41 55
–40°C to 125°C 98
25°C 40 52
–40°C to 125°C 38
25°C 35 44
–40°C to 125°C 33
25°C 265
25°C 212
25°C 135
–40°C to 125°C
25°C 32 mV
25°C 0.22 0.4
–40°C to 125°C 0.4
TPS7233Q
MIN TYP MAX
0.95 ×
V
O(nom)
µV/√Hz
µVrms
V
10
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PARAMETER
TEST CONDITIONS
‡
T
UNIT
Output voltage
V
I
V
V
D
I
100 mA
V
4.75 V
mV
I
250 mA
V
4.75 V
Pass-element series resistance
(
O)O
,
I
,
Ω
Input regulation
V
5.85 V to 10 V
50 µA ≤ I
≤ 250 mA
mV
I
5 mA to 250 mA
V
≤ 10 V
Output regulation
mV
I
250 mA
V
V
I
A
Ripple rejection
f
120 H
dB
I
250 mA
CSR
†
Ω
PG output low voltage
I
V
V
V
TPS7201Q, TPS7225Q, TPS7230Q
TPS7233Q, TPS7248Q, TPS7250Q, TPS72xxY
MICROPOWER LOW-DROPOUT (LDO) VOLTAGE REGULATORS
SLVS102G – MARCH 1995 – REVISED JUNE 2000
TPS7248Q electrical characteristics, IO = 10 mA, V
= 5.85 V, EN = 0 V, CO = 4.7 µF (CSR† = 1 Ω),
I
SENSE shorted to OUT (unless otherwise noted)
J
p
ropout voltage
p
p
pp
Output noise spectral density f = 120 Hz 25°C 2 µV/√Hz
Output noise voltage
PG trip-threshold voltage
PG hysteresis voltage
p
†
CSR refers to the total series resistance, including the ESR of the capacitor, any series resistance added externally, and PWB trace resistance
to CO.
‡
Pulse-testing techniques are used to maintain virtual junction temperature as close as possible to ambient temperature; thermal effects must
be taken into account separately.
VI = 5.85 V, IO = 10 mA 25°C 4.85
5.85 V ≤VI ≤ 10 V, 5 mA ≤ IO ≤ 250 mA –40°C to 125°C 4.75 4.95
= 10 mA,
O
†
= 1
=
z
,
,
)/I
, V
,
=
O
=
O
(4.75 V – V
IO = 250 mA
=
I
=
O
= 50 µA to
O
=
10 Hz ≤ f ≤ 100 kHz,
VO voltage decreasing from above V
= 1.2 mA,
PG
= 4.75
I
=
I
=
I
= 4.75 V,
,5.85 V ≤
,5.85 V ≤
= 50 µ
O
=
O
CO = 4.7 µF
CO = 10 µF
CO = 100 µF
= 4.12
I
O
I
≤ 10
I
PG
25°C 10 19
–40°C to 125°C 30
25°C 90 100
–40°C to 125°C 150
25°C 216 250
–40°C to 125°C 285
25°C 0.8 1
–40°C to 125°C 1.4
25°C 34
–40°C to 125°C 50
25°C 43 55
–40°C to 125°C 95
25°C 55 75
–40°C to 125°C 135
25°C 42 53
–40°C to 125°C 36
25°C 36 46
–40°C to 125°C 34
25°C 370
25°C 290
25°C 168
–40°C to 125°C
25°C 50 mV
25°C 0.2 0.4
–40°C to 125°C 0.4
TPS7248Q
MIN TYP MAX
0.95 ×
V
O(nom)
µVrms
V
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
11
TPS7201Q, TPS7225Q, TPS7230Q
PARAMETER
TEST CONDITIONS
‡
T
UNIT
Output voltage
V
I
V
V
D
I
100 mA
V
4.88 V
mV
I
250 mA
V
4.88 V
Pass-element series resistance
(
O)O
,
I
,
Ω
Input regulation
V
6 V to 10 V
50 µA ≤ I
≤ 250 mA
mV
I
5 mA to 250 mA
V
≤ 10 V
Output regulation
mV
I
250 mA
V
V
I
A
Ripple rejection
f
120 H
dB
I
250 mA
CSR
†
Ω
PG output low voltage
I
V
V
V
TPS7233Q, TPS7248Q, TPS7250Q, TPS72xxY
MICROPOWER LOW-DROPOUT (LDO) VOLTAGE REGULATORS
SLVS102G – MARCH 1995 – REVISED JUNE 2000
TPS7250Q electrical characteristics, IO = 10 mA, V
= 6 V , EN = 0 V , CO = 4.7 µF (CSR† = 1 Ω), SENSE
I
shorted to OUT (unless otherwise noted)
J
p
ropout voltage
p
p
pp
Output noise spectral density f = 120 Hz 25°C 2
Output noise voltage
PG trip-threshold voltage
PG hysteresis voltage
p
†
CSR refers to the total series resistance, including the ESR of the capacitor, any series resistance added externally , and PWB trace resistance
to CO.
‡
Pulse-testing techniques are used to maintain virtual junction temperature as close as possible to ambient temperature; thermal effects must
be taken into account separately.
VI = 6 V, IO = 10 mA 25°C 5
6 V ≤VI ≤ 10 V, 5 mA ≤ IO ≤ 250 mA –40°C to 125°C 4.9 5.1
= 10 mA,
O
†
= 1
,
,
)/I
, V
,
z
=
=
O
=
O
(4.88 V – V
IO = 250 mA
=
I
=
O
= 50 µA to
O
=
10 Hz ≤ f ≤ 100 kHz,
VO voltage decreasing from above V
= 1.2 mA,
PG
= 4.88
I
=
I
=
I
= 4.88 V,
,6 V ≤
,6 V ≤
= 50 µ
O
=
O
CO = 4.7 µF
CO = 10 µF
CO = 100 µF
= 4.25
I
O
I
≤ 10
I
PG
25°C 8 12
–40°C to 125°C 30
25°C 76 85
–40°C to 125°C 136
25°C 190 206
–40°C to 125°C 312
25°C 0.76 0.825
–40°C to 125°C 1.25
25°C 28
–40°C to 125°C 35
25°C 46 61
–40°C to 125°C 100
25°C 59 79
–40°C to 125°C 150
25°C 41 52
–40°C to 125°C 37
25°C 36 46
–40°C to 125°C 32
25°C 390
25°C 300
25°C 175
–40°C to 125°C
25°C 50 mV
25°C 0.19 0.4
–40°C to 125°C 0.4
TPS7250Q
MIN TYP MAX
0.95 ×
V
O(nom)
µV/√Hz
µVrms
V
12
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
Loading...