Tektronix TDS 794D, TDS 784D, TDS 754D, TDS 724D, TDS 580D Service Manual
...
Service Manual
TDS 500D, TDS 600B & TDS 700D
Digitizing Oscilloscopes
071-0136-00
Warning
The servicing instructions are for use by
qualified personnel only. To avoid personal
injury, do not perform any servicing unless you
are qualified to do so. Refer to the Safety
Summary prior to performing service.
Copyright T ektronix, Inc. All rights reserved.
T ektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes
that in all previously published material. Specifications and price change privileges reserved.
Printed in the U.S.A.
T ektronix, Inc., P.O. Box 1000, Wilsonville, OR 97070–1000
TEKTRONIX and TEK are registered trademarks of T ektronix, Inc.
FlexFormat and KlipChip are trademarks of T ektronix, Inc.
WARRANTY
T ektronix warrants that this product will be free from defects in materials and workmanship for a period of three (3) years
from the date of shipment. If any such product proves defective during this warranty period, T ektronix, at its option, either
will repair the defective product without charge for parts and labor, or will provide a replacement in exchange for the
defective product.
In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration of the
warranty period and make suitable arrangements for the performance of service. Customer shall be responsible for packaging
and shipping the defective product to the service center designated by T ektronix, with shipping charges prepaid. T ektronix
shall pay for the return of the product to Customer if the shipment is to a location within the country in which the T ektronix
service center is located. Customer shall be responsible for paying all shipping charges, duties, taxes, and any other charges
for products returned to any other locations.
This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate maintenance
and care. T ektronix shall not be obligated to furnish service under this warranty a) to repair damage resulting from attempts
by personnel other than T ektronix representatives to install, repair or service the product; b) to repair damage resulting from
improper use or connection to incompatible equipment; or c) to service a product that has been modified or integrated with
other products when the effect of such modification or integration increases the time or difficulty of servicing the product.
THIS WARRANTY IS GIVEN BY TEKTRONIX WITH RESPECT TO THIS PRODUCT IN LIEU OF ANY
OTHER WARRANTIES, EXPRESSED OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY
IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
TEKTRONIX’ RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND
EXCLUSIVE REMEDY PROVIDED TO THE CUST OMER FOR BREACH OF THIS WARRANTY. TEKTRONIX
AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT , SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR THE VENDOR HAS
ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.
Table of Contents
Specifications
General Safety Summary xi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Safety Summary xiii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preface xv. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual Structure xv. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual Conventions xvi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Related Manuals xvii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Contacting T ektronix xviii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Introduction xix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Strategy xix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Offerings xix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before You Begin xxi. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications 1–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Description 1–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
User Interface 1–2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Signal Acquisition System 1–3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Horizontal System 1–3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trigger System 1–5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acquisition Control 1–5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
On-Board User Assistance 1–6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Measurement Assistance 1–6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage 1–7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
I/O 1–7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display 1–8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Nominal Traits 1–9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Warranted Characteristics 1–17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Typical Characteristics 1–25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Information
Installation 2–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supplying Operating Power 2–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Environment 2–3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Applying and Interrupting Power 2–4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Repackaging Instructions 2–5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installed Options 2–5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Instructions 2–7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Screen Layout 2–7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Basic Procedures 2–7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TDS 500D, TDS 600B and TDS 700D Service Manual
i
Table of Contents
Theory of Operation
Theory of Operation 3–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Logic Conventions 3–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Module Overview 3–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Performance Verification Procedures
Performance Verification Procedures 4–1. . . . . . . . . . . . . . . . . . . . . . . . . .
Input Channels vs. Model 4–2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Conventions 4–2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brief Procedures 4–5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Self Tests 4–5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Functional T ests 4–7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Performance Tests 4–15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Prerequisites 4–15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Equipment Required 4–16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TDS 600B T est Record 4–19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TDS 500D/700D T est Record 4–23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TDS 794D T est Record 4–26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Signal Acquisition System Checks 4–29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Time Base System Checks 4–46. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Trigger System Checks 4–49. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Signal Checks 4–62. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Option 05 Video Trigger Checks 4–71. . . . . . . . . . .
Sine Wave Generator Leveling Procedure 4–88. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optical Filters Checks (TDS 500D/TDS 700D Only) 4–91. . . . . . . . . . . . . . . . . . . . .
Adjustment Procedures
Maintenance
Adjustment Procedures 5–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Requirements for Performance 5–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Usage 5–2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Equipment Required 5–5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Adjustment Instructions 5–6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Probe Adjustment for the P6139A Probe 5–10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Display Assembly Adjustment 5–21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance 6–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Related Maintenance Procedures 6–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preparation 6–2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inspection and Cleaning 6–4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Removal and Installation Procedures 6–9. . . . . . . . . . . . . . . . . . . . . . . . . .
Preparation — Please Read 6–9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Access Procedure 6–15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Procedures for External Modules 6–16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Procedures for Outer-Chassis Modules 6–28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Procedures for Inner-Chassis Modules 6–47. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disassembly for Cleaning 6–54. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ii
TDS 500D, TDS 600B and TDS 700D Service Manual
Options
Electrical Parts List
Diagrams
Mechanical Parts List
Table of Contents
Troubleshooting 6–57. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostics 6–57. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Firmware Updates 6–58. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hard Disk Drive Maintenance 6–59. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Options and Accessories 7–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Options 7–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standard Accessories 7–3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Optional Accessories 7–4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Parts List 8–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagrams 9–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Symbols 9–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mechanical Parts List 10–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts Ordering Information 10–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Replaceable Parts List 10–2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TDS 500D, TDS 600B and TDS 700D Service Manual
iii
Table of Contents
List of Figures
Figure 2–1: Map of Display Functions 2–8. . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–1: Map of display functions 4–3. . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–2: Verifying adjustments and signal-path compensation 4–6. .
Figure 4–3: Universal test hookup for functional tests – TDS 600B
shown 4–8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–4: Measurement of DC offset accuracy at zero setting 4–31. . . .
Figure 4–5: Initial test hookup 4–32. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–6: Measurement of DC accuracy at maximum offset and
position 4–35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–7: Initial test hookup 4–37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–8: Optional initial test hookup 4–37. . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–9: Measurement of analog bandwidth 4–40. . . . . . . . . . . . . . . . . .
Figure 4–10: Initial test hookup 4–42. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–11: Measurement of channel delay – TDS 684B shown 4–44. . . .
Figure 4–12: Initial test hookup 4–46. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–13: Measurement of accuracy – Long-term and delay time 4–48
Figure 4–14: Initial test hookup 4–50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–15: Measurement of time accuracy for pulse and glitch
triggering 4–51. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–16: Initial test hookup 4–53. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–17: Measurement of trigger-level accuracy 4–55. . . . . . . . . . . . .
Figure 4–18: Initial test hookup 4–58. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–19: Measurement of trigger sensitivity – 50 MHz results
shown on a TDS 684B screen 4–59. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–20: Initial test hookup 4–62. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–21: Measurement of main trigger out limits 4–64. . . . . . . . . . . . .
Figure 4–22: Initial test hookup 4–66. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–23: Measurement of probe compensator frequency 4–68. . . . . . .
Figure 4–24: Subsequent test hookup 4–69. . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–25: Measurement of probe compensator amplitude 4–70. . . . . .
Figure 4–26: Jitter test hookup 4–72. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–27: Jitter test displayed waveform – TDS 684B shown 4–73. . . .
Figure 4–28: Jitter test when completed – TDS 684B shown 4–74. . . . . . .
Figure 4–29: Triggered signal range test – 300 mV 4–75. . . . . . . . . . . . . . .
Figure 4–30: Triggered signal range test – 75 mV 4–76. . . . . . . . . . . . . . . .
iv
TDS 500D, TDS 600B and TDS 700D Service Manual
Table of Contents
Figure 4–31: 60 Hz Rejection test hookup 4–77. . . . . . . . . . . . . . . . . . . . . .
Figure 4–32: 60 Hz Rejection test setup signal 4–77. . . . . . . . . . . . . . . . . . .
Figure 4–33: Subsequent 60 Hz Rejection test hookup 4–78. . . . . . . . . . . .
Figure 4–34: 60 Hz Rejection test result – TDS 684B shown 4–79. . . . . . .
Figure 4–35: Line count accuracy test hookup 4–80. . . . . . . . . . . . . . . . . . .
Figure 4–36: Line count accuracy test setup waveform –
TDS 684B shown 4–81. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–37: Line count accuracy correct result waveform 4–82. . . . . . . .
Figure 4–38: Setup for sync duty cycle test 4–84. . . . . . . . . . . . . . . . . . . . . .
Figure 4–39: Sync duty cycle test: one-div neg pulse waveform 4–85. . . . .
Figure 4–40: Sync duty cycle test: critically adjusted pulse 4–86. . . . . . . .
Figure 4–41: Sine wave generator leveling equipment setup 4–88. . . . . . .
Figure 4–42: Equipment setup for maximum amplitude 4–90. . . . . . . . . .
Figure 4–43: Reference-receiver performance-verification set up 4–93. . .
Figure 4–44: Optical impulse of Ch1 input from OA5022 Optical Atten–
uator (OIG501 / OIG502 fed into optical attenuator in Step 1) 4–95. .
Figure 4–45: Optical impulse response for OC–12 SONET Reference
Receiver 4–98. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 4–46: Optical impulse response for OC–12 SONET Reference
Receiver 4–99. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 5–1: Accessing the protection switch 5–9. . . . . . . . . . . . . . . . . . . . .
Figure 5–2: Hookup for probe compensation 5–11. . . . . . . . . . . . . . . . . . . .
Figure 5–3: Performing probe compensation 5–12. . . . . . . . . . . . . . . . . . . .
Figure 5–4: Proper and improper probe compensation 5–12. . . . . . . . . . .
Figure 5–5: Exposing the Inner Probe Tip 5–13. . . . . . . . . . . . . . . . . . . . . .
Figure 5–6: Initial test hookup 5–14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 5–7: Exposing the probe body 5–16. . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 5–8: Initial test hookup 5–17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 5–9: Locations of P6139A Probe Adjustments 5–19. . . . . . . . . . . . .
Figure 5–10: Adjustments versus front-corner response 5–20. . . . . . . . . . .
Figure 5–11: Five and Ten Percent Luminance Patches 5–22. . . . . . . . . . .
Figure 6–1: External modules 6–12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6–2: Outer-chassis modules 6–13. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6–3: Inner-chassis modules 6–14. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6–4: Knob removal 6–17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6–5: Line fuse and line cord removal 6–18. . . . . . . . . . . . . . . . . . . .
Figure 6–6: Rear cover and cabinet removal 6–21. . . . . . . . . . . . . . . . . . . .
TDS 500D, TDS 600B and TDS 700D Service Manual
v
Table of Contents
Figure 6–7: Front cover, trim ring, menu buttons, and attenuator
panel removal (front cover not shown) 6–22. . . . . . . . . . . . . . . . . . . . . .
Figure 6–8: A12 Front-panel assembly removal 6–24. . . . . . . . . . . . . . . . . .
Figure 6–9: Cabinet modules removal 6–27. . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6–10: A14 D1 bus and analog-power and digital-power cables
removal 6–29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6–11: Remove circuit board assembly from oscilloscope 6–30. . . . .
Figure 6–12: Remove circuit board from assembly 6–31. . . . . . . . . . . . . . .
Figure 6–13: Circuit board installed 6–33. . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6–14: Circuit board removal 6–34. . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6–15: A11 Processor/display removal 6–36. . . . . . . . . . . . . . . . . . . .
Figure 6–16: Hard disk removal 6–38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6–17: Board bracket removal 6–39. . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6–18: A10 Acquisition board removal 6–42. . . . . . . . . . . . . . . . . . . .
Figure 6–19: Floppy disk drive removal 6–44. . . . . . . . . . . . . . . . . . . . . . . .
Figure 6–20: Rear chassis removal 6–46. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6–21: A16 Low voltage power supply removal 6–48. . . . . . . . . . . . .
Figure 6–22: Display assembly removal 6–50. . . . . . . . . . . . . . . . . . . . . . . .
Figure 6–23: Display driver board removal 6–51. . . . . . . . . . . . . . . . . . . . .
Figure 6–24: Front subpanel removal 6–53. . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6–25: Accessing the protection switch 6–58. . . . . . . . . . . . . . . . . . . .
Figure 6–26: Primary troubleshooting procedure 6–60. . . . . . . . . . . . . . . .
Figure 6–27: Module isolation troubleshooting procedure 6–62. . . . . . . . .
Figure 6–28: A16 Low voltage power supply module isolation
troubleshooting procedure 6–63. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6–29: Power supply voltage measurement locations 6–64. . . . . . . .
Figure 6–30: Color display troubleshooting procedure 6–65. . . . . . . . . . . .
Figure 6–31: Horizontal and vertical sync signals – color display 6–66. . .
Figure 6–32: A video signal with white, black, and blanking levels –
color display 6–66. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 6–33: Processor/acquisition troubleshooting procedure 6–67. . . . .
Figure 6–34: Processor/front panel troubleshooting procedure 6–68. . . . .
Figure 6–35: Attenuator/acquisition troubleshooting procedure 6–69. . . .
Figure 6–36: A11 DRAM Processor/Display module 6–70. . . . . . . . . . . . . .
Figure 6–37: A10 Acquisition module (test points) 6–71. . . . . . . . . . . . . . .
Figure 9–1: Interconnections 9–2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 9–2: Block Diagram 9–4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
vi
TDS 500D, TDS 600B and TDS 700D Service Manual
Table of Contents
Figure 10–1: External modules 10–7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 10–2: Outer-chassis modules 10–10. . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 10–3: Inner-chassis modules 10–12. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 10–4: Cables, bottom view 10–14. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 10–5: Cables, top view 10–16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 10–6: Floppy disk drive 10–18. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Figure 10–7: Accessories 10–20. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TDS 500D, TDS 600B and TDS 700D Service Manual
vii
Table of Contents
List of Tables
Table 1–1: Key features of the TDS 500D, 600B and 700D
oscilloscopes 1–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 1–2: Record length and divisions per record vs. TDS model 1–4. .
Table 1–3: Nominal traits — Signal acquisition system 1–11. . . . . . . . . . .
Table 1–4: Nominal traits — Time base system 1–12. . . . . . . . . . . . . . . . . .
Table 1–5: Nominal traits — Triggering system 1–13. . . . . . . . . . . . . . . . .
Table 1–6: Nominal traits — Display system 1–15. . . . . . . . . . . . . . . . . . . .
Table 1–7: Nominal traits — GPIB interface, output ports, and
power fuse 1–16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 1–8: Nominal traits — Data handling and reliability 1–16. . . . . . . .
Table 1–9: Nominal traits — Mechanical 1–17. . . . . . . . . . . . . . . . . . . . . . .
Table 1–10: Warranted characteristics — Signal acquisition system 1–20
Table 1–11: Warranted characteristics — Time base system 1–22. . . . . . .
Table 1–12: Warranted characteristics — Triggering system 1–22. . . . . .
Table 1–13: Warranted characteristics — Output ports, probe
compensator, and power requirements 1–23. . . . . . . . . . . . . . . . . . . . .
Table 1–14: Warranted characteristics — Environmental 1–24. . . . . . . . .
Table 1–15: Certifications and compliances 1–26. . . . . . . . . . . . . . . . . . . . .
Table 1–16: Typical characteristics — Signal acquisition system 1–27. . .
Table 1–17: Typical characteristics — Triggering system 1–30. . . . . . . . .
viii
Table 2–1: Power cord conductor identification 2–2. . . . . . . . . . . . . . . . .
Table 2–2: Power cord identification 2–2. . . . . . . . . . . . . . . . . . . . . . . . . .
Table 2–3: Effects of corrupted data 2–4. . . . . . . . . . . . . . . . . . . . . . . . . .
Table 4–1: Test equipment 4–16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 4–2: DC offset accuracy (zero setting) 4–30. . . . . . . . . . . . . . . . . . . .
Table 4–3: DC Voltage measurement accuracy 4–34. . . . . . . . . . . . . . . . . .
Table 4–4: Analog bandwidth 4–39. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 4–5: Delay between channels worksheet 4–45. . . . . . . . . . . . . . . . . .
Table 4–6: Trigger level accuracy readout 4–54. . . . . . . . . . . . . . . . . . . . . .
Table 4–7: Delayed trigger level accuracy readout 4–56. . . . . . . . . . . . . . .
Table 4–8: Available Filters 4–91. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 4–9: Reference Receiver Filter Options 4–91. . . . . . . . . . . . . . . . . . .
Table 4–10: Option 3C and 4C Specifications
(not available on TDS 794D) 4–92. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TDS 500D, TDS 600B and TDS 700D Service Manual
Table of Contents
Table 4–11: Available receivers 4–92. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 4–12: Bessel Thompson frequency response and reference
receiver limits 4–100. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 5–1: Calibration Tests 5–3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 5–2: Adjustments Required for Module Replaced 5–4. . . . . . . . . .
Table 5–3: Adjustments and Dependencies 5–4. . . . . . . . . . . . . . . . . . . . .
Table 5–4: Test Equipment, Fixtures, and Supplies 5–5. . . . . . . . . . . . . .
Table 5–5: GPIB Board Configuration 5–7. . . . . . . . . . . . . . . . . . . . . . . . .
Table 6–1: Relative susceptibility to static-discharge damage 6–3. . . . . .
Table 6–2: External inspection check list 6–5. . . . . . . . . . . . . . . . . . . . . . .
Table 6–3: Internal inspection check list 6–6. . . . . . . . . . . . . . . . . . . . . . .
Table 6–4: Tools Required for Module Removal 6–11. . . . . . . . . . . . . . . . .
Table 6–5: Normal supply voltages (measured on J26 and J27 on
the A11 DRAM Processor/Display module) 6–64. . . . . . . . . . . . . . . . . .
Table 6–6: No-load supply voltages (measured on J5 and J6 on
the A17 Main LV Power Supply module) 6–64. . . . . . . . . . . . . . . . . . . .
Table 7–1: Options 7–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 7–2: Standard accessories 7–4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 7–3: Optional accessories 7–5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Table 7–4: Recommended Probe Cross Reference 7–6. . . . . . . . . . . . . . .
Table 7–5: Accessory software 7–9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TDS 500D, TDS 600B and TDS 700D Service Manual
ix
Table of Contents
x
TDS 500D, TDS 600B and TDS 700D Service Manual
General Safety Summary
Review the following safety precautions to avoid injury and prevent damage to
this product or any products connected to it. To avoid potential hazards, use this
product only as specified.
Only qualified personnel should perform service procedures.
To Avoid Fire or
Personal Injury
Use Proper Power Cord. Use only the power cord specified for this product and
certified for the country of use.
Ground the Product. This product is grounded through the grounding conductor
of the power cord. To avoid electric shock, the grounding conductor must be
connected to earth ground. Before making connections to the input or output
terminals of the product, ensure that the product is properly grounded.
Observe All Terminal Ratings. To avoid fire or shock hazard, observe all ratings
and markings on the product. Consult the product manual for further ratings
information before making connections to the product.
Connect and Disconnect Properly . Do not connect or disconnect probes or test
leads while they are connected to a voltage source.
Do Not Operate Without Covers. Do not operate this product with covers or panels
removed.
Use Proper Fuse. Use only the fuse type and rating specified for this product.
Avoid Exposed Circuitry. Do not touch exposed connections and components
when power is present.
Do Not Operate With Suspected Failures. If you suspect there is damage to this
product, have it inspected by qualified service personnel.
Do Not Operate in Wet/Damp Conditions.
Do Not Operate in an Explosive Atmosphere.
Provide Proper Ventilation. Refer to the manual’s installation instructions for
details on installing the product so it has proper ventilation.
TDS 500D, TDS 600B and TDS 700D Service Manual
xi
General Safety Summary
Symbols and Terms
T erms in this Manual. These terms may appear in this manual:
WARNING. Warning statements identify conditions or practices that could result
in injury or loss of life.
CAUTION. Caution statements identify conditions or practices that could result in
damage to this product or other property.
T erms on the Product. These terms may appear on the product:
DANGER indicates an injury hazard immediately accessible as you read the
marking.
WARNING indicates an injury hazard not immediately accessible as you read the
marking.
CAUTION indicates a hazard to property including the product.
Symbols on the Product. The following symbols may appear on the product:
WARNING
High Voltage
Protective Ground
(Earth) T erminal
CAUTION
Refer to Manual
Double
Insulated
xii
TDS 500D, TDS 600B and TDS 700D Service Manual
Service Safety Summary
Only qualified personnel should perform service procedures. Read this Service
Safety Summary and the General Safety Summary before performing any service
procedures.
Do Not Service Alone. Do not perform internal service or adjustments of this
product unless another person capable of rendering first aid and resuscitation is
present.
Disconnect Power. To avoid electric shock, disconnect the mains power by means
of the power cord or, if provided, the power switch.
Use Caution When Servicing the CRT. To avoid electric shock or injury, use
extreme caution when handling the CRT. Only qualified personnel familiar with
CRT servicing procedures and precautions should remove or install the CRT.
CRTs retain hazardous voltages for long periods of time after power is turned off.
Before attempting any servicing, discharge the CRT by shorting the anode to
chassis ground. When discharging the CRT, connect the discharge path to ground
and then the anode. Rough handling may cause the CRT to implode. Do not nick
or scratch the glass or subject it to undue pressure when removing or installing it.
When handling the CRT, wear safety goggles and heavy gloves for protection.
Use Care When Servicing With Power On. Dangerous voltages or currents may
exist in this product. Disconnect power, remove battery (if applicable), and
disconnect test leads before removing protective panels, soldering, or replacing
components.
To avoid electric shock, do not touch exposed connections.
X-Radiation. To avoid x-radiation exposure, do not modify or otherwise alter the
high-voltage circuitry or the CRT enclosure. X-ray emissions generated within
this product have been sufficiently shielded.
TDS 500D, TDS 600B and TDS 700D Service Manual
xiii
Service Safety Summary
xiv
TDS 500D, TDS 600B and TDS 700D Service Manual
Preface
Manual Structure
This preface contains information needed to properly use this manual to service
the TDS 500D, TDS 600B and TDS 700D Oscilloscopes, as well as general
information critical to safe and effective servicing of this oscilloscope.
The following models are covered:
TDS 500D: TDS 520D, TDS 540D, and TDS 580D
TDS 600B: TDS 620B, TDS 644B, TDS 680B, and TDS 684B
TDS 700D: TDS 724D, TDS 754D, TDS 784D, and TDS 794D
This manual is divided into sections, such as Specifications and Theory of
Operation. Further, it is divided into subsections, such as Product Description
and Removal and Installation Procedures.
Sections containing procedures also contain introductions to those procedures. Be
sure to read these introductions because they provide information needed to do
the service correctly and efficiently. The following is a brief description of each
manual section.
H Specifications contains a product description of the TDS 500D, TDS 600B
and TDS 700D Oscilloscopes and tables of the characteristics and descriptions that apply to it.
H Operating Information includes general information and operating instruc-
tions at the level needed to safely power on and service this oscilloscope. A
statement of the service strategy that this manual supports, and instructions
for shipment of the oscilloscopes are found in this section.
H Theory of Operation contains circuit descriptions that support general service
and fault isolation.
H Performance Verification contains a collection of procedures for confirming
that these oscilloscopes function properly and meet warranted limits.
H Adjustment Procedures contains a collection of procedures for adjusting
these oscilloscopes to meet warranted limits.
H Maintenance contains information and procedures for doing preventive and
corrective maintenance of these oscilloscopes. Instructions for cleaning, for
TDS 500D, TDS 600B and TDS 700D Service Manual
xv
Preface
Manual Conventions
module removal and installation, and for fault isolation to a module are
found here.
H Options contains information on servicing any of the factory-installed
options that may be present in your oscilloscope.
H Electrical Parts List contains a statement referring you to Mechanical
Replaceable Parts, where both electrical and mechanical modules are listed.
H Diagrams contains a block diagram and an interconnection diagram useful
for isolating failed modules.
H Mechanical Parts List includes a table of all replaceable modules, their
descriptions, and their Tektronix part numbers.
This manual uses certain conventions which you should become familiar with
before doing service.
Modules
Channels
Safety
Symbols
Throughout this manual, any replaceable component, assembly, or part of these
oscilloscopes is referred to generically as a module. In general, a module is an
assembly, like a circuit board, rather than a component, like a resistor or an
integrated circuit. Sometimes a single component is a module; for example, each
chassis part of the oscilloscope is a module.
Some TDS models have two auxiliary channels called AUX 1 and AUX 2,
instead of CH 3 and CH 4. References to these channels default to CH 3 and
CH 4. If your oscilloscope is one of models TDS 520D, TDS 620B, TDS 680B,
or TDS 724D, read AUX 1 and AUX 2 respectively for all references to CH 3
and CH 4 in this manual.
Symbols and terms related to safety appear in the Safety Summary found at the
beginning of this manual.
Besides the symbols related to safety, this manual uses the following symbols:
STOP. The stop labels information which must be read in order to correctly do
service and to avoid incorrectly using or applying service procedures.
xvi
The clock icon labels procedure steps which require a pause to wait for
the oscilloscope to complete some operation before you can continue.
TDS 500D, TDS 600B and TDS 700D Service Manual
Related Manuals
Preface
Various icons such as the example icon at the left are used in procedures
to help identify certain readouts and menu functions on screen.
The TDS 500D, TDS 600B and TDS 700D Oscilloscopes come with the
following manuals:
TDS 500D, TDS 600B & TDS700D User Manual (Tektronix part number
071-0130-XX) contains a tutorial to quickly show you how to operate the
TDS 500D, TDS 600B and TDS 700D Oscilloscopes and an in depth discussion
of how to more completely use their features. Applications are also discussed.
TDS 500D, TDS 600B & TDS 700D Reference (Tektronix part number
071-0137-XX) contains a brief overview of oscilloscope operation.
TDS Family (500D, 600B, and 700D) Programmer Diskette (part of the User
Manual) contains information for programmed operation via the GPIB interface.
Included are the complete command set, setup information, and programming
examples.
TDS 500D, TDS 600B & TDS 700D Technical Reference (Tektronix part number
071-0135-XX) contains performance verification procedures and specifications.
TDS 500D, TDS 600B and TDS 700D Service Manual
xvii
Preface
Contacting Tektronix
Product
Support
Service
Support
For other
information
To write us Tektronix, Inc.
For application-oriented questions about a Tektronix measurement product, call toll free in North America:
1-800-TEK-WIDE (1-800-835-9433 ext. 2400)
6:00 a.m. – 5:00 p.m. Pacific time
Or, contact us by e-mail:
tm_app_supp@tek.com
For product support outside of North America, contact your
local Tektronix distributor or sales office.
Contact your local Tektronix distributor or sales office. Or, visit
our web site for a listing of worldwide service locations.
http://www.tek.com
In North America:
1-800-TEK-WIDE (1-800-835-9433)
An operator will direct your call.
P.O. Box 1000
Wilsonville, OR 97070-1000
xviii
TDS 500D, TDS 600B and TDS 700D Service Manual
Introduction
Service Strategy
STOP. Throughout this manual, any field-replaceable component, assembly, or
part of this oscilloscope is referred to generically as a module.
This manual contains all the information needed for periodic maintenance of the
TDS 500D, TDS 600B and TDS 700D Oscilloscopes. (Examples of such
information are procedures for checking performance and for readjustment.)
Further, it contains all information for corrective maintenance down to the
module level. This means that the procedures, diagrams, and other troubleshooting aids help isolate failures to a specific module, rather than to components of
that module. Once a failure is isolated, replace the module with a fresh unit
obtained from the factory.
All modules are listed in Mechanical Parts List. To isolate a failure to a module,
use the fault isolation procedures found in Section 6, Maintenance Information.
To remove and replace any failed module, follow the instructions in Removal and
Installation Procedures, also found in Section 6.
Service Offerings
Warranty Repair Service
Tektronix provides service to cover repair under warranty as well as other
services that may provide a cost-effective answer to your service needs.
Whether providing warranty repair service or any of the other services listed
below, Tektronix service technicians, trained on Tektronix products, are best
equipped to service your TDS 500D, TDS 600B and TDS 700D Oscilloscopes.
Tektronix technicians are appraised of the latest information on improvements to
the product as well as the latest new options to the product.
Tektronix warrants this product for three years from date of purchase, excluding
probes for which the warranty is one year. (The warranty appears after the title
page and copyright page in this manual.) Tektronix technicians provide warranty
service at most Tektronix service locations worldwide. Your Tektronix product
catalog lists all service locations worldwide.
TDS 500D, TDS 600B and TDS 700D Service Manual
xix
Introduction
Repair or Calibration
Service
The following services may be purchased to tailor repair and/or calibration of
your TDS 500D, TDS 600B and TDS 700D Oscilloscopes to fit your requirements.
At-Depot Service. Tektronix offers several standard-priced adjustment (calibration) and repair services:
H A single repair and/or adjustment.
H Calibrations using equipment and procedures that meet the traceability
standards specific to the local area.
H Annual maintenance agreements that provide for either calibration and repair
or calibration only of the oscilloscope.
Of these services, the annual maintenance agreement offers a particularly
cost-effective approach to service for many owners of the TDS 500D, TDS 600B
and TDS 700D Oscilloscopes. Such agreements can be purchased to span several
years.
On-Site Service. The annual maintenance agreement can be purchased with
on-site service, with repair and calibration done at your facility. This service
reduces the time your oscilloscope is out of service when calibration or repair is
required.
Self Service
Tektronix supports repair to the module level by providing Module Exchange and
Module Repair and Return.
Module Exchange. This service reduces down time for repair by allowing you to
exchange most modules for remanufactured ones. Tektronix ships you an updated
and tested exchange module from the Beaverton, Oregon service center, typically
within 24 hours. Each module comes with a 90-day service warranty.
Module Repair and Return. This service returns to you within 10 days the same
module that you shipped to Tektronix. The module shipped is repaired, tested,
and returned to you from the Beaverton, Oregon service center. It is not updated
to match current modules of the same type. Again, each module comes with a
90-day service warranty.
For More Information. Contact your local Tektronix service center or sales
engineer for more information on any of the repair or adjustment services just
described.
xx
TDS 500D, TDS 600B and TDS 700D Service Manual
Before You Begin
Introduction
This manual is for servicing the TDS 500D, TDS 600B and
TDS 700D Oscilloscopes. To prevent injury to yourself or damage to the
oscilloscope, do the following tasks before you attempt service:
H Read the Safety Summary found at the beginning of this manual.
H Read Service Strategy in this section and Supplying Operating Power in
section 2.
When using this manual for servicing, be sure to read and follow all warnings,
cautions, and notes.
TDS 500D, TDS 600B and TDS 700D Service Manual
xxi
Introduction
xxii
TDS 500D, TDS 600B and TDS 700D Service Manual
Specifications
Product Description
This section begins with a general description of the traits of the TDS 500D,
TDS 600B and TDS 700D oscilloscopes. Three sections follow, one for each of
three classes of traits: nominal traits, warranted characteristics, and typical
characteristics.
The TDS 500D, TDS 600B and TDS 700D oscilloscopes are portable, four-channel instruments suitable for use in a variety of test and measurement applications
and systems. Table 1–1 lists key features.
T able 1–1: Key features of the TDS 500D, 600B and 700D oscilloscopes
Feature TDS 600B TDS 500D & TDS 700D
Digitizing rate,
maximum
TDS 684B: 5 GS/s on ea. of 4 ch
TDS 680B: 5 GS/s on ea. of 2 ch
TDS 644B: 2.5 GS/s on ea. of 4 ch
TDS 620B: 2.5 GS/s on ea. of 2 ch
TDS 580D, TDS 784D,
TDS 794D: 4 GS/s
TDS 540D, 754D: 2 GS/s
TDS 520D, 724D: 1 GS/s
Analog bandwidth TDS 794D: 2 GHz
TDS 580D, TDS 680B, 684B, and 784D: 1 GHz
TDS 520D, 540D, 620B, 644B, 724D and 754D: 500 MHz
No. of Channels TDS 644B & 684B: 4
TDS 620B & 680B: 2 + 2
Record lengths,
maximum
Acquisition modes Sample, envelope, peak detect
Trigger modes Modes include:
Display TDS 520D, 540D, 580D, 620B, 680B: Monochrome
15,000 samples 50,000 samples
and average
Edge, logic, and pulse.
Video trigger , with option 05, modes include:
NTSC, SECAM, PAL, HDTV, and FlexFormat.
(Not available on TDS 794D)
Communications Trigger with option 2C (available on
TDS 500D/700D), modes include: AMI, CMI, and NRZ
TDS 644B, 684B, 724D, 754D, 784D, 794D: Color
1
TDS 540D, 580D,
TDS 754D, 784D & 794D: 4
TDS 520D & 724D: 2 + 2
(500,000 with option 1M)
(8,000,000 with option 2M)
Sample, envelope, average,
high-resolution, and
peak-detect
1
TDS 500D, TDS 600B and TDS 700D Service Manual
1–1
Specifications
T able 1–1: Key features of the TDS 500D, 600B and 700D oscilloscopes (cont.)
Feature TDS 500D & TDS 700DTDS 600B
Storage Floppy disk drive:
1.44 Mbyte, 3.5 inch, DOS 3.3-or-later floppy disk drive
Internal hard disk drive
(optional on the TDS 500D and 700D)
Iomega Zip drive compatible
NVRAM storage for saving waveforms, hardcopies, and setups
I/O Full GPIB programmability .
Hardcopy output using GPIB, RS-232, or Centronics ports
1
Two plus Two channel operation allows up to two of the four channels to be
displayed simultaneously. Channels not displayed can be used to couple a
triggering signal to the oscilloscope.
User Interface
Indicators
Menus
Use a combination of front-panel buttons, knobs, and on-screen menus to control
the many functions of the oscilloscope. The front-panel controls are grouped
according to function: vertical, horizontal, trigger, and special. Set a function you
adjust often, such as vertical positioning or the time base setting, directly by its
own front-panel knob. Set a function you change less often, such as vertical
coupling or horizontal mode, indirectly using a selected menu.
Pressing one (sometimes two) front-panel button(s), such as vertical menu,
displays a main menu of related functions, such as coupling and bandwidth, at
the bottom of the screen. Pressing a main-menu button, such as coupling,
displays a side menu of settings for that function, such as AC, DC, or GND
(ground) coupling, at the right side of the screen. Pressing a side-menu button
selects a setting such as DC.
On-screen readouts help you keep track of the settings for various functions,
such as vertical and horizontal scale and trigger level. Some readouts use the
cursors or the automatic parameter extraction feature (called measure) to display
the results of measurements made or the status of the instrument.
General Purpose Knob
1–2
Assign the general purpose knob to adjust a selected parameter function. More
quickly change parameters by toggling the SHIFT button. Use the same method
as for selecting a function, except the final side-menu selection assigns the
general purpose knob to adjust some function, such as the position of measurement cursors on screen, or the setting for a channel fine gain.
TDS 500D, TDS 600B and TDS 700D Service Manual
Specifications
GUI
The user interface also makes use of a GUI, or Graphical User Interface, to make
setting functions and interpreting the display more intuitive. Some menus and
status are displayed using iconic representations of function settings, such as
those shown here for full, 250 MHz and 20 MHz bandwidth. Such icons allow
you to more readily determine status or the available settings.
Signal Acquisition System
The signal acquisition system provides up to four, full-featured vertical channels
with calibrated vertical scale factors from 1 mV to 10 V per division, depending
on TDS model. All channels can be acquired simultaneously.
Each of the full-featured channels can be displayed, vertically positioned, and
offset, and their vertical coupling specified. Some models can have their
bandwidth limited (250 MHz or 20 MHz). Fine gain can also be adjusted.
Besides these channels, up to three math waveforms and four reference waveforms are available for display. (A math waveform results when you specify dual
waveform operations, such as add, on any two channels. A reference waveform
results when you save a waveform in a reference memory).
Horizontal System
There are three horizontal display modes: main only, main intensified, and
delayed only. You can select among various horizontal record length settings.
A feature called “Fit to Screen” allows you to view entire waveform records
within the 10 division screen area. Waveforms are compressed to fit on the
screen. See Table 1–2.
Both the delayed only display and the intensified zone on the main intensified
display may be delayed by time with respect to the main trigger. Both can be set
to display immediately after the delay (delayed runs after main mode). The
delayed display can also be set to display at the first valid trigger after the delay
(delayed-triggerable modes).
The delayed display (or the intensified zone) may also be delayed by a selected
number of events. In this case, the events source is the delayed-trigger source.
The delayed trigger can also be set to occur after a number of events plus an
amount of time.
TDS 500D, TDS 600B and TDS 700D Service Manual
1–3
Loading...