Page 1
013_D
24 V (ac) Transformer 013
Accessories
07/14
Replaces: New
Installation & Operation Manual
Introduction
The 24 V (ac) Transformer 013 has a 115 V (ac) primary and a 24 V (ac) secondary
with a capacity of 96 VA. A resettable circuit breaker protects the transformer from
overloading. A 4" x 4" electrical junction box is included for mounting.
1 of 4
© 2014
013_D - 07/14
Page 2
-------------------------------------------------
------------------------------------------------------
It is the installers responsibility to ensure that this device is safely
--------------------------------------------------
installed according to all applicable codes and standards. tekmar
is not responsible for damages resulting from improper installation
and/or maintenance.
Read this Manual BEFORE using this equipment.
Failure to read and follow all safety and use information can result in
personal injury, property damage, or damage to the equipment.
Keep this Manual for future reference.
Disconnect all power before opening the device.
•
Improper installation and operation of this device could result in damage
•
to the equipment and possibly even personal injury or death.
Installation
Check the Contents
Check the contents of this package. If any of the contents listed are missing or
damaged, please refer to the Limited Warranty and Product Return Procedure on
the back of this brochure and contac t your wholesaler or tekmar sales representative
for assistance. Type 013 includes:
One 24 V (ac) Transformer 013
•
One Installation & Operation Manual 013_D
•
Preparation
Tools Required
Phillips screwdriver• Wire Stripper•
Materials Required
Wood screws
•
Wire nuts
•
Installation Location
Choose the placement of the 24 V (ac) early in the construction process to
enable proper wiring during rough-in.
Consider the following:
Keep dry. Avoid potential leakage onto the control.
•
No exposure to extreme temperatures beyond 32-122°F (0 to 50°C).
•
Easy access for wiring.
•
------------------------------------------------------
--------------------------------------------------
2 conductor, 18 AWG LVT solid wire
•
2 conductor with ground, 14 AWG cable
•
-------------------------------------------------
2 of 4
© 2014 013_D - 07/14
Page 3
Step 1 - Install the Electrical Box
Mount the electrical box to a wall with two woods screws centered on a wall stud.
Step 2 - Line Voltage Wiring
Pull two conductor 14 AWG cable from the power disconnect to the electrical
•
box. Strip wire to 3/8" (10 mm) for all connections.
Connect the cable ground to the electrical box ground screw.
•
Connect the cable neutral wire to the transformer white wire using a wire nut.
•
Connect the cable line voltage wire to the transformer black wire using a wire nut.
•
Mount the transformer to the electrical box by aligning the slotted holes with the
•
electrical box screws.
Tighten the electrical box screws with a Phillips screwdriver.
•
Step 3 - Low Voltage Wiring
The top of the transformer has two Phillips screws. Loosen the screws using a
•
Phillips screwdriver.
Strip the 18 AWG wire to 3/8" (10 mm) for all connections.
•
Connect the “C” on the transformer to the control “C” wiring terminal.
•
Connect the “R” on the transformer to the control “R” wiring terminal.
•
Resettable Circuit Breaker
In the event that the current between the 24 V (ac) R and C terminals exceeds 4
A, the 013 circuit breaker will trip thereby shutting off 24 V (ac) power. Push the
button on the top of the 013 to reset the circuit breaker.
Testing and Troubleshooting
Using a volt meter, measure the voltage on the 24 V (ac) wiring terminals. The
voltage should measure 22 to 30 V (ac). If no voltage is present, press the button
to reset the circuit breaker, then check the 115 V (ac) supply voltage.
Technical Data
24 V (ac) Transformer 013 96 VA, includes Mounting Box
Literature 013_C, 013_D
Packaged weight 5.0 lb (2300 g)
Dimensions
Approvals
Ambient conditions
Input power supply
Output power available
Circuit breaker
4" L x 4" W x 5-7/8" H (102 x 102 x 150 mm)
Transformer UL C US, Electrical Box UL and CSA
Indoor use only, 32 to 122°F (0 to 50°C)
115 V (ac) ± 10%, 60 Hz
22 to 30 V (ac), 60 Hz, Class 2
4 A
3 of 4
© 2014 013_D - 07/14
Page 4
Limited Warranty and Product Return Procedure
Limited Warranty The liability of tekmar under this warranty is limited. The Purchaser, by taking receipt
of any tekmar product (“Product”), acknowledges the terms of the Limited Warranty in effect at the time
of such Product sale and acknowledges that it has read and understands same.
The tekmar Limited Warranty to the Purchaser on the Products sold hereunder is a manufacturer’s passthrough warranty which the Purchaser is authorized to pass through to its customers. Under the Limited
Warranty, each tekmar Product is warranted against defects in workmanship and materials if the Product
is installed and used in compliance with tekmar’s instructions, ordinary wear and tear excepted. The passthrough warranty period is for a period of twenty-four (24) months from the production date if the Product is
not installed during that period, or twelve (12) months from the documented date of installation if installed
within twenty-four (24) months from the production date.
The liability of tekmar under the Limited Warranty shall be limited to, at tekmar’s sole discretion: the cost of parts
and labor provided by tekmar to repair defects in materials and / or workmanship of the defective product; or to
the exchange of the defective product for a warranty replacement product; or to the granting of credit limited to
the original cost of the defective product, and such repair, exchange or credit shall be the sole remedy available
from tekmar, and, without limiting the foregoing in any way, tekmar is not responsible, in contract, tort or strict
product liability, for any other losses, costs, expenses, inconveniences, or damages, whether direct, indirect,
special, secondary, incidental or consequential, arising from ownership or use of the product, or from defects in
workmanship or materials, including any liability for fundamental breach of contract.
The pass-through Limited Warranty applies only to those defective Products returned to tekmar during the warranty period. This Limited Warranty does not cover the cost of the parts or labor to remove or transport the defective Product, or to reinstall the repaired or replacement Product, all such costs and expenses being subject to
Purchaser’s agreement and warranty with its customers.
Any representations or warranties about the Products made by Purchaser to its customers which are different
from or in excess of the tekmar Limited Warranty are the Purchaser’s sole responsibilit y and obligation. Purchaser
shall indemnify and hold tekmar harmless from and against any and all claims, liabilities and damages of any
kind or nature which arise out of or are related to any such representations or warranties by Purchaser to its
customers.
The pass-through Limited Warrant y does not apply if the returned Product has been damaged by negligence by persons other than tekmar, accident, fire, Act of God, abuse or misuse; or has been damaged by modifications, alterations or attachments made subsequent to purchase which have not been authorized by tekmar; or if the Product was
not installed in compliance with tekmar’s instructions and / or the local codes and ordinances; or if due to defective
installation of the Product; or if the Product was not used in compliance with tekmar’s instructions.
THIS WARRANT Y IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IM PLIED, WHICH T HE GOVERNING
LAW ALLOWS PARTIES TO CONTRACTUALLY EXCLUDE, INCLUDING , WITHOUT LIMITATION, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, DURABILITY OR DESCRIPTION OF THE PRODUCT, ITS NON-INFRINGEMENT OF ANY RELEVANT PATENTS OR TRADEMARKS, AND
ITS COM PLIANCE WITH OR N ON-VIO LATION OF AN Y APPLICABLE EN VIRO NMENTAL, HEALTH OR SAFET Y
LEGISLATION; THE TERM OF ANY OTHER WARRANTY NOT HEREBY CONTRACTUALLY EXCLUDED IS LIMITED SUCH THAT IT SHALL NOT EXTEND BEYOND TWENTY-FOUR (24) MONTHS FROM THE PRODUCTION
DATE, TO THE EXTENT THAT SUCH LIMITATION IS ALLOWED BY THE GOVERNING LAW.
Product Warranty Return Procedure All Products that are believed to have defects in workmanship or materials must be returned, together with a written description of the defect, to the tekmar Representative assigned to
the territory in which such Product is located. If tekmar receives an inquiry from someone other than a tekmar
Representative, including an inquiry from Purchaser (if not a tekmar Representative) or Purchaser’s customers,
regarding a potential warranty claim, tekmar’s sole obligation shall be to provide the address and other contact
information regarding the appropriate Representative.
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or
other reproductive harm. For more information: www.watts.com/prop65
Product design, software and literature are Copyright ©2014 by tekmar Control Systems Ltd.,
A Watts Water Technologies Company. Head Offi ce: 5100 Silver Star Road, Vernon, B.C.
Canada V1B 3K4, 250-545-7749, Fax. 250-545-0650
All specifications are subject
to change without notice.
4 of 4 013_D - 07/14.
Web Site
: www.tekmarControls.com
Loading...