Teac QUICK 552E User Manual
TEAC CD-552E CD-ROM Drive
Quick Installation Guide page 1
Drive Installation Directions
The drive is operated in horizontal position. The eject
button is located on the right side of the panel. Installation position is not allowed to be tilted more than 15
degrees out of the horizontal position.
Jumpers for IDE Configuration
The strap is factory-preset as shown:
SLM
C
A
S
Pin 1
Digital audio
output connector
40-pin IDE flat cable
connector
Analog audio
output connector
Power connector
Installation and Connection
Note:
To use the TEAC CD-ROM drive an IDE
(ATAPI) controller is required. Usually it is integrated on the system board of your PC. The
drivers required for operating the CD-ROM
drive are a part of your operating system.
Very important:
Switch off your PC and any attached devices
and disconnect the power cord(s). It is not
sufficent to switch off the power switch! Do
the same if the CD-ROM drive is reconfigured.
(1) Open the case of your PC and lift it off carefully.
(2) Configure the CD-ROM drive if neccessary.
(3) Locate a free slot for 5.25” drives and install the
drive using the provided four screws.
(4) Connect the power cable and the 40-pin data cable
(assure the correct orientation, pin 1 is often
marked with a color stripe) to the drive. Connecting in the wrong orientation may damage the drive
and the PC!
The TEAC CD-552E can be operated in the modes
Cable Select (CS), Master (MA) or Slave (SL).
Important:
During setting the mode be sure to switch off
respectively disconnect any voltages connected to the drive (see section “Installation
and Connection”).
CSSLM
––X
– X –
X ––
Remarks
A
Master: CD-ROM drive is configured as first IDE
drive (basic setting).
This configuration can be used only if the drive is
connected to the second IDE controller
(secondary IDE). If a hard disk is already operated
at the secondary IDE controller (configured as
master) the jumper setting at the CD-ROM has to
be changed to slave.
Slave: CD-ROM drive is configured as second IDE
drive.
If there is only one hard disk in the PC the CDROM can be operated at the same IDE connection
parallel to this hard disk. Important: The data rates
of both devices may be decreased.
Cable Select: Master/slave detection is achieved
by the controller.
Remarks: X: jumper set
–: jumper not set (left open)
Audio cable
40-pin IDE
CD-552E
Pin 1
Power cable
data cable
(5) Connect the provided audio cable to the sound
card.
Usually sound cards offer more than one connec-
tor to connect an audio cable to. Please refer to
the manual of the sound card to find the connector in question.
(6) Close the case of the PC. Do not forget to connect
other devices and accessories if there are any.
TEAC CD-552E CD-ROM Drive
Quick Installation Guide page 2
(7) Connect the PC to the wall outlet and switch it on.
Important:
If your PC will not start up correctly switch it
off immediately and check all of the connections and jumper settings.
Maintenance and Cleaning
Maintenance and repairs shall only be carried out by
qualified personal and specialized firms. Otherwise the
drive may be severely damaged.
The front panel of the drive may be cleaned with a soft
dry cloth. Heavier kinds of solings are removed with a
damp cloth and a little bit of a non-aggressive cleaning
fluid.
Caution:
Do not use cleaning CDs which will remove
dirt of the lense of the laser aided by a little
brush. Do not clean the inner parts of your
TEAC CD-ROM drive with compressed air.
Any of these methods may cause damage to
your TEAC CD-ROM drive.
Handling
Check the CD-ROM before inserting it into the drive. It
should not have finger prints or other dirt on it. Especially at high reading velocities dirt may increase the
number of reading errors.
Very important:
Shape CDs, a kind of CD which is not shaped
like the normal round CD, are not allowed to
be used in this drive. Otherwise rotational
forces may cause severe damage to the drive.
Reproducing Audio CDs
Audio CDs may be reproduced with special software
like the CD Player of Windows95/98/ME/2000/XP. Audio CDs are recognized and played automatically. Otherwise you may use the keys on the drive itself:
Software Installation
Windows 95/98/ME/2000/XP does not require a software installation. The drive is recognized automatically.
If you like to access the drive under DOS (not necessary for the DOS box of Windows 95/98/ME/2000/XP)
you have to insert the CD-ROM driver into “Config.sys”
and MSCDEX.EXE into “AUTOEXEC.BAT”. Please
copy the CD-ROM driver from the drivers floppy to your
hard disk.
CONFIG.SYS:
DEVICE=C:\CDROMDRV.SYS /D:MSCD001
AUTOEXEC.BAT:
C:\WINDOWS\COMMAND\MSCDEX.EXE /D:MSCD001
Head-
phone jack
Volume control
a) Play/Skip
After inserting an audio CD you have to press this
key to start the reproduction. In some cases it can
be necessary to adjust the volume at your sound
card. Pressing the key again starts the next music
title. The remaining music of the title reproduced
before is skipped.
b) Eject/Stop
Pressing this key once during the reproduction of
a music title stops playing the title. Pressing the
key again ejects the CD tray containing the audio
CD.
Very important:
Please do not try to reproduce data CDs under any circumstances. This may cause severe damage to your audio equipment!
Busy LED
Play/skip key
Eject/stop key
In case of warranty: www.teac.de/support/german/index.htm
Loading...