Sylvania LC370SS8M User Manual

37” Digital / Analog
HIGH-DEFINITION TELEVISION
LCD TV
Owner’s Manual
LC370SS8 M
WATCHING TVINTRODUCTION CONNECTION INITIAL SETTING OPTIONAL SETTING
TO RECEIVE DIGITAL/ANALOG SIGNAL, YOU MUST CONNECT ANTENNA.
IF YOU NEED ADDITIONAL ASSISTANCE WITH SETUP OR OPERATING AFTER READING OWNER’S MANUAL, PLEASE CALL TOLL FREE 1-800-968-3429, OR VISIT OUR WEB SITE AT http://www.SylvaniaConsumerElectronics.com
TROUBLESHOOTING
INFORMATION
© 2008 Funai Electric Co., Ltd.
NTRODUCTION
I
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The important note is located on the rear of the cabinet.
Important Safeguards
1. READ INSTRUCTIONS - All the safety and operating instructions
should be read before the appliance is operated.
2. RETAIN INSTRUCTIONS - The safety and operating instructions
should be retained for future reference.
3. HEED WARNINGS - All warnings on the appliance and in the
operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS - All operating and use instructions
should be followed.
5. CLEANING - Unplug TV from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted service and,
that for some specific reason, such as the possibility of the loss of an authorization code for a CAT V converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description otherwise required in item 5.
6. ATTACHMENTS - Do not use attachments not recommended by
the TV manufacturer as they may cause hazards.
7. WATER AND MOISTURE - Do not use this TV near water, for
example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like.
8. ACCESSORIES - Do not place this TV on an
unstable cart, stand, tripod, bracket, or table. The TV may fall, causing serious injury to someone, and serious damage to the appliance. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the T V.
Any mounting of the appliance should follow
the manufacturer’s instructions and should use a mounting accessory recommended by the manufacturer. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
AMEUBLES - Cet appareil ne doit être placé
que sur un meuble (avec ou sans roulettes) recommandé par le fabricant. Si vous l’ installez sur un meuble à roulettes, déplacez les deux ensembles avec précaution. Un arrêt brusque, l’utilisation d’une force excessive et des surfaces irrégulières risquent de déstabiliser l’ensemble et de le renverser.
9. VENTILATION - Slots and openings in the
cabinet and the back or bottom are provided for ventilation and to ensure reliable operation of the TV and to protect it from overheating, these openings must not be blocked or covered. The openings should never be blocked by placing the TV on a bed, sofa, rug, or other similar surface. This TV should never be placed near or over a radiator or heat register. This TV should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
10. POWER SOURCES - This TV should be operated only from the type
of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For TVs intended to operate from battery power, or other sources, refer to the operating instructions.
11. GROUNDING OR POLARIZATION - This TV is equipped with a
2
EN
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND MAINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THE APPLIANCE.
polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug.
12. POWER-CORD PROTECTION - Power-supply cords should be
routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.
13. OUTDOOR ANTENNA GROUNDING - If an outside antenna or
cable system is connected to the TV, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA No. 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (Fig. A)
EXAMPLE OF ANTENNA GROUNDING AS PER
S2898A
14. LIGHTNING - For added protection for this TV receiver during a
15. POWER LINES - An outside antenna system should not be located
16. OVERLOADING - Do not overload wall outlets and extension
17. OBJECT AND LIQUID ENTRY - Never push objects of any kind into
FIGURE A
NATIONAL ELECTRICAL CODE
GROUND CLAMP
ELECTRIC SERVICE EQUIPMENT
NEC - NATIONAL ELECTRICAL CODE POWER SERVICE GROUNDING
lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the TV due to lightning and power-line surges.
in the vicinity of overhead power lines or other electric light of power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.
cords as this can result in a risk of fire or electric shock.
this TV through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock.
GROUND CLAMPS
ELECTRODE SYSTEM (NEC ART 250, PART H)
ANTENNA LEAD IN WIRE
ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)
GROUNDING CONDUCTORS (NEC SECTION 810-21)
INTRODUCTION
Never spill liquid of any kind on the TV.
18. SERVICING - Do not attempt to service this TV yourself as opening
or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
19. DAMAGE REQUIRING SERVICE - Unplug this TV from the wall
outlet and refer servicing to qualified service personnel under the following conditions: a. When the power supply cord or plug is damaged or frayed. b. If liquid has been spilled, or objects have fallen into the TV. c. If the TV has been exposed to rain or water. d. If the TV does not operate normally by following the operating
instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and will often require extensive work by a
qualified technician to restore the TV to its normal operation. e. If the TV has been dropped or damaged in any way. f. When the TV exhibits a distinct change in performance, this
indicates a need for service.
5
Precautions
LAMP IN LCD CONTAINS MERCURY, DISPOSE ACCORDING TO LOCAL, STATE OR FEDERAL LAW
20. REPLACEMENT PARTS - When replacement parts are required, be
sure the service technician uses replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, injury to persons or other hazards.
21. SAFETY CHECK - Upon completion of any service or repairs to this
TV, ask the service technician to perform routine safety checks to determine that the TV is in proper operating condition.
22. HEAT - This TV product should be situated away from heat sources
such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT. ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
FCC WARNING
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
RADIO-TV INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4) Consult the dealer or an experienced radio/TV technician for help.
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Note to CATV system installer:
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground should be connected to the grounding system of the building as close to the point of cable entry as practical.
CONNECTION
INITIAL SETTING
WATCHING TV INFORMATION
OPTIONAL SETTING TROUBLESHOOTING
“HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.”
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.
Product that have earned ENERGY STAR® are designed to protect the environment through superior energy efficiency.
3
EN
NTRODUCTION
I
LOCATION
For safe operation and satisfactory performance of the unit, keep the following in mind when selecting a place for its installation:
Shield it from direct sunlight and keep it away from sources of intense heat.
Avoid dusty or humid places.
Avoid places with insufficient ventilation for proper heat dissipation. Do not block the ventilation holes at the top and bottom of the unit. Do not place the unit on a carpet because this will block the ventilation holes.
Install the unit in a horizontal position.
Avoid locations subject to strong vibration.
Do not place the unit near strong magnetic fields.
Avoid moving the unit to locations where temperature differences are extreme.
Be sure to unplug the AC power cord from the outlet before carrying the unit.
TO AVOID THE HAZARDS OF ELECTRICAL SHOCK AND FIRE
Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting it from an AC outlet. Grasp it by the plug.
• If, by accident, water is spilled on the unit, unplug the power cord immediately and take the unit to our authorized service center for
• servicing. Do not place anything directly on top of the unit.
The serial number of this product may be found on the back of the unit. No others have the same serial number as yours. You should record the number and other vital information here and retain this book as a permanent record of your pur­chase to aid identification in case of theft.
date of purchase
dealer purchase from
Note about recycling:
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance with your local recycling regulations. Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.
dealer phone No.
model No.
serial No
dealer address
Supplied Accessories
5
owner’s manual (1EMN23142)
If you need to replace these accessories, please refer to the part No. with the illustrations and call our toll free
• customer support line found on the cover of this manual. Depending on your antenna system, you may need different types of combiners (mixers) or separators (splitters).
• Contact your local electronics store for these items.
Symbols Used in this Manual
5
The following is the description for the symbols used in this manual. Description refers to:
: Digital TV operation
DTV
: Analog TV operation
TV
If neither symbol appears under the function heading, operation is applicable to both.
quick start guide (1EMN23143)
remote control (NF015UD)
batteries (AA x 2)
4
EN
INTRODUCTION
Features5
DTV/TV/CATV
-
You can use your remote control to select channels which are broadcast in digital format and conventional analog format. Also, cable subscribers can access their cable TV channels.
Program Information Display (DTV only)
-
You can display the title, contents and other information of the current DTV program on the TV screen.
Auto Channel Scan
-
This unit automatically scans and memorizes channels available in your area, eliminating difficult setup procedures.
V-chip
-
This feature allows you to block children’s access to inappropriate programs.
Closed Caption Decoder
-
Built-in closed caption decoder displays text for closed caption supported programming.
MTS/SAP Tuner
-
Audio can be selected from the remote control.
Auto Shut Off Function
-
If there is no signal input from the antenna terminal and no operation for 15 minutes, the unit will turn off automatically.
Sleep Timer
-
This feature will automatically turned off the power of the unit at a specific time.
Choices for On-screen Language
-
Select your on-screen language: English, Spanish or French.
Stereo Sound Function
PLL Frequency Synthesized Tuning
-
Provides free and easy channel selection and lets you tune directly to any channel using the channel number buttons on the remote control.
Resume
-
This unit automatically memorizes settings if a power failure occurs.
HDMI Input
PC Input
Component Video Input
S-video Input
AV Input
Digital Audio Coaxial Output
© 2008 Funai Electric Co., Ltd. All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed, downloaded or stored in
any storage medium, in any form or for any purpose without the express prior written consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content herein without the obligation to notify any person or organization of such changes.
with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way without the express written consent of Funai. All other trademarks used herein remain the exclusive property of their respective owners. Nothing contained in this manual should be construed as granting, by implication or otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law.
Contents5
INTRODUCTION
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Symbols Used in this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Remote Control Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Installing the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
CONNECTION
Basic Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
External Device Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
INITIAL SETTING
Initial Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Auto Channel Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Language Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
WATCHING TV
Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Still Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Switching Each Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Switching Audio Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Screen Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
TV Screen Display Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
OPTIONAL SETTING
Channel List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Manual Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Antenna Confirmation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Picture Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Sound Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Closed Caption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
DTV Closed Caption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
CC Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
V-chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
PC Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
HDMI Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
TROUBLESHOOTING
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
INFORMATION
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Cable Channel Designations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Electrical Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Other Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back cover
EN
CONNECTION
INITIAL SETTING
WATCHING TV INFORMATION
OPTIONAL SETTING TROUBLESHOOTING
5
NTRODUCTION
I
Remote Control Function5
1. POWER button (p13)
Press to turn the unit on and off.
2. Number buttons (p16)
Press to select channels.
-
button
Press to shift the minor channel
• from the major channel.
3. SETUP button (p14)
Press to display the main menu.
4. s / B / K / L buttons (p13)
Press to move left/ right/ up/
down through the items.
5. ENTER button (p13)
Press to decide the command of setting when the main menu is displayed.
6. BACK button (p19)
Press to return to previous menu operation.
7. CH RETURN button (p16)
Press to return to previous channel.
8. VOL. X / Y buttons (p16)
Press to adjust the volume.
9. MUTE button (p16)
Press to turn the sound on and off.
10. INPUT SELECT button (p17)
Press to access connected
• external device like a DVD player or VCR.
11. SLEEP button (p21)
Press to activate the sleep timer.
12. AUDIO button (p18)
Digital Mode (DTV)
Press to select the audio language.
Analog Mode (TV)
Press to select the audio mode.
13. STILL button (p17)
Press to pause screen image.
14. SCREEN MODE button (p20)
Press to select aspect ratio available for the TV screen.
15. INFO button (p19)
Digital Mode (DTV)
Press to display the channel
• information, signal type and TV setting.
Analog Mode (TV)
Press to display the channel
• number, signal type and TV setting.
External Input Mode
Press to display the external
• input mode, signal type and TV setting.
16. CH K / L buttons (p16)
Press to select channels and the external input mode.
Installing the Batteries
5
Install the batteries (AA x 2) matching the polarity indicated inside battery compartment of the remote control.
Battery Precautions:
• Be sure to follow the correct polarity as indicated in the battery compartment. Reversed batteries may cause damage to the device.
• Do not mix different types of batteries together (e.g., Alkaline and Carbon-Zinc) or old batteries with fresh ones.
• If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.
• Do not try to recharge batteries; they can overheat and rupture.
6
EN
INTRODUCTION
Control Panel5
Rear Panel5
PC-IN
AUDIO
COMPONENT 1
R
YR
AUDIO
AUDIO
L
PbPrL
S VIDEO VIDEO
VIDEO 1
COMPONENT 2
YR
AUDIO
PbPrL
rear of this unit
10 11
12
side of this unit
1. POWER button (p13)
Press to turn the unit on and off.
CONNECTION
INITIAL SETTING
POWER
INPUT SELECT
CHANNEL
VOLUME
SETUP
2. INPUT SELECT button (p17)
Press to access connected an external device like a
1 2
3
4
5
• DVD player or VCR. Press to decide the command of setting when the
• menu is displayed.
3. CHANNEL K / L buttons (p16)
Press to select channels or move up/down through the main menu items.
4. VOLUME X / Y buttons (p16)
Press to adjust the volume or move right (X) / left (Y) through the main menu items.
5. SETUP button (p14)
6
Press to display the main menu.
6. Infrared Sensor Window
Receives infrared rays transmitted from the remote
WATCHING TV INFORMATION
control.
rear of this unit
1. PC-IN jack (p12)
VGA cable connection for PC.
1
2. HDMI IN jacks (p9)
OPTIONAL SETTING TROUBLESHOOTING
HDMI connection for an HDMI device.
2
3. AUDIO IN jacks (p9)
RCA audio cable connection for a DVI device. (For
3 4 5
PC-IN
COMPONENT 1
VIDEO 1
COMPONENT 2
6
HDMI 1-IN jack only)
4. AUDIO OUT jacks (p11)
RCA audio cable connection for an external device. Use analog audio input jacks of an external device.
5. DIGITAL AUDIO OUT (COAXIAL) jack (p11)
Digital audio coaxial cable connection for a decoder or an audio receiver. Use digital audio input jack of an external device.
6. ANT. IN jack (p8)
RF coaxial cable connection for your antenna or cable
7
box.
7. AC power cord
Connect to a standard AC outlet to supply power to
8
9
VIDEO 2
R
L
S-VIDEO
AUDIO
VIDEO
this unit.
8. PC-IN AUDIO jack (p12)
Mini-plug audio cable connection for PC. Use line out jack of a PC.
9. AUDIO input jacks (p10)
RCA audio cable connection for an external device.
10. VIDEO input jack (p11)
RCA video cable connection for an external device.
11. S-VIDEO input jack (p10)
S-video cable connection for an external device.
side of this unit
12. COMPONENT and AUDIO input jacks (p10)
Component video cable and RCA audio cable connection for an external device. Use component video and audio output jacks of an external device.
EN
7
ONNECTION
C
Cables not included.
Please purchase the necessary cables at your local store.
Basic Connection
5
This section describes how to connect the unit to an antenna, cable/satellite box, etc.
Note:
• Be sure your antenna or other device is connected properly before plugging in the power cord.
[Antenna Cable Connection]
When connecting the unit to an antenna or cable TV company (without cable/satellite box) Connect the RF coaxial cable on your home outlet to the antenna input jack of this unit.
e.g.)
VHF / UHF antenna
rear of this unit
or
cable TV company
Once connections are completed, turn on the unit and begin initial setup.
*
Channel scanning is necessary for the unit to memorize all available channels in your area. (Refer to “Initial Setup” on page 13.)
RF coaxial cable
Note:
• For your safety and to avoid damage to device, please unplug the RF coaxial cable from the antenna input jack before moving the unit.
• If you use an antenna to receive analog TV, it should also work for DTV reception. Outdoor or attic antennas will be more effective than settop versions.
• To easily switch your reception source between antenna and cable, install an antenna selector.
• If you connect to the cable system directly, contact the CAT V installer.
[Connection to Cable Box or Satellite Box]
Connect the RF coaxial cable on your home outlet to the input jack of the cable/satellite box. Use another RF coaxial cable to connect the antenna input jack of the unit to the output jack of the cable/satellite box.
e.g.)
satellite
dish
cable/satellite box
rear of this unit
or
cable TV company
*
Required cables and connecting methods differ depending on the cable/satellite box. For more information, please contact your cable/satellite provider.
RF coaxial cable
RF OUTANT. IN
RF coaxial cable
8
EN
DVI OUT
AUDIO OUT
RL
Cables not included.
Please purchase the necessary cables at your local store.
External Device Connection
5
[HDMI Connection]
HDMI (High Definition Multimedia Interface) transports high definition video and multi-channel digital audio through a single cable. It ensures that the content sent from the source to TV is of the highest possible resolution.
rear of this unit
CONNECTION
e.g.)
HDMI cable
HDMI OUT
DVD player with the HDMI output jack
To HDMI 1-IN or
HDMI 2-IN jack
Note:
• This unit accepts 480i / 480p / 720p / 1080i video signals, and 32kHz / 44.1kHz / 48kHz audio signals.
• This unit accepts only 2 channel audio signal (LPCM).
• You need to select “PCM” for the digital audio output of the device connected or the HDMI audio setting. There may be no audio output if you select “Bitstream”, etc.
• This TV only accepts signals compliant with EIA861.
[HDMI-DVI Connection]
If your video device has a DVI output jack, connect using a HDMI-DVI conversion cable.
rear of this unit
e.g.)
HDMI-DVI conversion cable
To HDMI 1-IN jack
INITIAL SETTING
WATCHING TVINTRODUCTION
OPTIONAL SETTING
TROUBLESHOOTING
Cable box or satellite box with the DVI output jack
To AUDIO IN jacks
RCA audio cable
Note:
• This unit accepts 480i / 480p / 720p / 1080i video signals.
• An HDMI-DVI conversion cable requires a separate audio cable connection as well. As such, only the HDMI 1-IN jack can be used.
• Audio signals are converted from digital to analog for this connection.
• DVI does not display 480i image that is not compliant with EIA/CEA-861/861B.
INFORMATION
9
EN
ONNECTION
COMPONENT VIDEO OUT
PrPbY
AUDIO OUT
RL
C
Cables not included.
Please purchase the necessary cables at your local store.
[Component Video Cable Connection]
Component video connection offers better picture quality for video devices connected to the unit. Use a component video cable to connect the unit to external video devices equipped with component video output jacks. If you connect to the unit’s COMPONENT 1 video input jack, connect RCA audio cables to the audio L/R jacks of COMPONENT 1. If you connect to the unit’s COMPONENT 2 video input jack, connect RCA audio cables to the audio L/R jacks of COMPONENT 2.
component video cable
(red)(blue)(green)
e.g.)
DVD player with the component video output jacks
RCA audio cable
rear of this unit
PC-IN
(green)
COMPONENT 1
YR
(blue)
PbPrL
(red)
COMPONENT 2
YR
AUDIO
AUDIO
S VIDEO VIDEO
VIDEO 1
AUDIO
R
AUDIO
L
Note:
• This unit accepts 480i / 480p / 720p / 1080i video signals.
[S-video Cable Connection]
S-video connection offers good picture quality for video devices connected to the unit. Use an S-video cable to connect the unit to external video devices equipped with S-video output jack. If you connect to the unit’s VIDEO 1 S-video input jack, connect RCA audio cables to the audio L/R jacks of VIDEO 1. If you connect to the unit’s VIDEO 2 S-video input jack, connect RCA audio cables to the audio L/R jacks of VIDEO 2.
e.g.)
DVD player with the S-video output jack
AUDIO OUT
S-VIDEO
OUT
RL
S-video cable
RCA audio cable
rear of this unit
PC-IN
AUDIO
COMPONENT 1
R
YR
AUDIO
AUDIO
L
L
Pb
S VIDEO VIDEO
Pr
VIDEO 1
COMPONENT 2
R
Y
AUDIO
Note:
• If you connect to the S-video jack and the video jack at the same time, the S-video connection will have priority.
10
EN
Cables not included.
Please purchase the necessary cables at your local store.
[Video Connection]
Video connection offers standard picture quality for video devices connected to the unit. If you connect to the unit’s VIDEO 1 video input jack, connect RCA audio cables to the audio L/R jacks of VIDEO 1. If you connect to the unit’s VIDEO 2 video input jack, connect RCA audio cables to the audio L/R jacks of VIDEO 2. When the audio jack of the video device is monaural, connect the RCA audio cable to the audio L input jack.
rear of this unit
e.g.)
camcorder video game
AUDIO OUT
VIDEO
RL
OUT
PC-IN
AUDIO
COMPONENT 1
YR
AUDIO
PbPrL
S VIDEO VIDEO
COMPONENT 2
R
Y
AUDIO
VIDEO 1
R
AUDIO
L
RCA video cable
VCR
RCA audio cable
Note:
• If you connect to the S-video jack and the video jack at the same time, the S-video connection will have priority.
[Audio Output Connection] [Digital]
If you connect this unit to an external digital audio device, you can enjoy multi-channel audio like 5.1ch digital broadcasting sound.
[Analog]
If you connect this unit to an external analog audio device, you can enjoy stereo (2 channel) audio.
CONNECTION
INITIAL SETTING
WATCHING TVINTRODUCTION
OPTIONAL SETTING
TROUBLESHOOTING
e.g.)
Stereo system
e.g.)
Dolby Digital decoder
AUDIO IN
RL
DIGITAL AUDIO
COAXIAL IN
RCA audio cable
INFORMATION
rear of this unit
To AUDIO OUT
jack
digital audio coaxial cable
To DIGITAL AUDIO OUT jack
11
EN
ONNECTION
C
Cables not included.
Please purchase the necessary cables at your local store.
[PC Connection]
This unit is equipped with a PC-IN jack. If you connect this unit to your PC, you can use this unit as a computer monitor.
VGA cable should be
with ferrite core.
rear of this unit
e.g.)
To monitor jack
VGA cable
mini-plug audio cable
To PC-IN jack
PC
Note:
• Please purchase the VGA that has a ferrite core.
To audio line out jack
To PC-IN AUDIO jack
12
EN
NITIAL SETTING
I
These operations are accessible by remote control. Some may also be accessible by controls on the main unit.
Initial Setup
5
This section will guide you through the unit’s initial setting which includes selecting a language for your on-screen menu and auto channel scan, which automatically scans and memorizes viewable channels.
Before you begin:
Make sure if the unit is connected to antenna or cable.
After making all the necessary connections, press
1
[POWER] to turn on the unit.
This operation may take a few moments.
Use [Cursor K / L] to select the on-screen language
2
from the choices on the right side of the TV screen. (English / Español / Français)
Initial Setup
Initial Setup
Select the language for setup display.
Elija el idioma de ajuste.
Sélectionner langue écran config.
ENTER
Select Enter Exit
“Initial Setup” menu on step 3 will be displayed in the selected language after you press [ENTER].
Use [Cursor K / L] to select “Air” for TV channels or
3
“Cable” for CATV channels, then press [ENTER].
English
Español
Français
SETUP
Note:
• If you connect the cable system directly, contact the CAT V installer.
• If you press [POWER] or [SETUP] during auto channel scan, this setting will be canceled.
• The initial auto channel scan function can be executed for either “Air” or “Cable” only once. When you change the connection (Air/Cable), set auto channel scan again. (Refer to page 14.)
• You can cancel or exit the initial auto channel scan menu by pressing [SETUP].
• If there is no signal input from the antenna terminal and no operation for several seconds after you turn on the unit, “Helpful Hints” appears. Follow the instructions listed on the TV screen.
2-2
No channel is registered. Press and hold "ENTER" key on the remote control for 3 seconds. Contact support hotline provided on manual or back of unit.
Sin canal registrado. Pulse durante 3 segundos la tecla "ENTER" en el control remoto. Llame teléfono de apoyo en manual o atrás de TV.
Pas de chaîne consign. Enfoncez "ENTER" 3 secondes sur la télécommande. Contacter numero d'urgence dans manuel ou arrière appareil.
INITIAL SETTING
WATCHING TVINTRODUCTION CONNECTION
OPTIONAL SETTING
TROUBLESHOOTING
Initial Setup
Initial Setup
Make sure the antenna is connected to "ANT.IN" jack. Select the destination of "ANT.IN" jack.
Air
Or
Cable
BACK
ENTER
Select Enter Exit
Scanning and memorizing of channels start
Air Cable
ANT.IN
SETUP
Back
automatically.
Initial Setup
Initial Setup
Now the system is scanning for channels,please wait.
5%
Analog channels 1ch
Digital channels 0ch
When the scanning and memorizing are completed,
SETUP
Exit
the lowest memorized channel in the broadcasting will be displayed.
INFORMATION
13
EN
NITIAL SETTING
I
Main Menu
5
This section describes the overview of the main menu displayed when you press [SETUP]. For more details, see the reference page for each item. The main menu consists of the function setting items below.
Press [SETUP].
EXIT
To exit settings.
PICTURE
You can adjust the picture quality. (Refer to “Picture Adjustment” on page 24.)
SOUND
You can adjust the sound quality. (Refer to “Sound Adjustment” on page 25.)
CHANNEL
You can automatically scan the viewable channels and remove those that are undesired. (Refer to “Auto Channel Scan” on page 14.)
DETAIL
You can change the display format for closed caption, which displays the dialogue of a TV program or other information across the TV screen. (Refer to “Closed Caption” on page 26.) Set the viewing limitations. (Refer to “V-chip” on page 30.) Adjust the position, stability and clarity of the PC screen. (Refer to “PC Settings” on page 33.) And select the sound input for the HDMI jack if your TV is connected to a HDMI device. (Refer to “HDMI Audio” on page 34.)
LANGUAGE
You can change the language (English, Spanish, French) displayed on the main menu. (Refer to “Language Selection” on page 15.)
Auto Channel Scan
5
If you switch wires (e.g., between antenna and CATV) or if you move the unit to a different area after the initial setting, or if you restore the DTV channel you deleted, you will need to perform auto channel scan.
Before you begin:
Make sure if the unit is connected to antenna or cable.
Press [SETUP] to display the main menu.
1
Use [Cursor K / L] to select “CHANNEL” , then press
2
[ENTER].
Use [Cursor K / L] to select “Autoscan”, then press
3
[ENTER].
Use [Cursor K / L] to select an appropriate option, then press [ENTER].
When aerial antenna is connected, select “Air”.
• When connected to CATV, select “Cable”.
• Scanning and memorizing of channels start
• automatically.
Channel
Channel
Autoscan Channel List Manual Register Antenna
Autoscan
Autoscan
Autoscan will rescan all channels. This may take a while to complete.
Select the destination of "ANT.IN" jack.
Air
Or
Cable
ANT.IN
Back Air Cable Cable
1hour
14
EN
Now the system is scanning for channels, please wait.
72%
Analog channels 10ch
When the scanning and memorizing are completed,
Digital channels 6ch
SETUP
Exit
the lowest memorized channel will be displayed.
Note:
• If you connect the cable system directly, contact the CAT V installer.
• If you press [POWER] or [SETUP] during auto channel scan, the setting will be canceled.
• Channel settings will be saved even if the power fails.
• If you need the English menus instead of the Spanish or French menus you are having, press [SETUP]. Use
[Cursor K [ENTER]. Use [Cursor K / L] to select “English”, then press [ENTER]. Press [SETUP] to exit the main menu.
• With regard only to the digital channel, even after the scanning is complete if you unplug the AC power cord before turning off the unit by pressing [POWER], the channel setting may be lost.
/ L] to select “IDIOMA” or “LANGAGE”, then press
Language Selection
5
You can choose English, Spanish, or French as your on-screen language.
Press [SETUP] to display the main menu.
1
Use [Cursor K / L] to select “LANGUAGE”, then press
2
[ENTER].
INITIAL SETTING
Use [Cursor K / L] to select “English”, “Español” or
3
“Français”, then press [ENTER].
Language
Language
Select the language for setup display.
Elija el idioma de ajuste.
Sélectionner langue écran config.
Press [SETUP] to exit.
4
WATCHING TVINTRODUCTION CONNECTION
OPTIONAL SETTING
English
Español
Français
TROUBLESHOOTING
INFORMATION
EN
15
ATCHING TV
W
Channel Selection
5
Select channels by pressing [CH
K /
] or [the Number buttons].
L
Volume Adjustment
5
This section describes how to adjust the volume. The mute function, which turns the sound off and on, is also described.
To select the memorized channels, use [CH
[the Number buttons]. To select the non-memorized channels use
[the Number buttons].
To Use [the Number buttons]
TV
When selecting analog channel 12
-
DTV
When selecting digital channel 12-1
-
Be sure to press [–] before entering the minor channel number.
Press [CH RETURN] to return to the previously
• viewed channel.
About digital TV broadcasting:
With its high definition broadcast, digital broadcasting far surpasses analog broadcasting in both its picture and sound quality.
What is the minor channel?
By using high compression technology, digital broadcasting offers a service that enables multiple signals to send simultaneously. Therefore, you can select more than one program per major channel since digital broadcasting technology distinguishes between multiple channels broadcast by a single network.
NTSC (analog mode)
CH4
[Air Time]
18:00
18:30
19:00
19:30
20:00
20:30
ATSC (digital mode)
No signal
CH4
CH4
(high definition TV)
CH4-1
CH4
CH4
No signal
CH4-1
CH4
/
K
L] or
No signal
No signal
CH4-2
CH4-2
/
X
Use [VOL.
The volume bar will be displayed at the bottom of
• the TV screen when adjusting the volume. The volume bar display will automatically disappear
• in a few seconds.
Press [MUTE] to turn off and on the sound.
“Mute” is displayed on the TV screen for a few
• seconds.
Press [MUTE] again or [VOL. original volume.
Y
] to adjust the audio volume.
Volume 20
Mute
/
X
Y
] to recover the
16
major channel
: change automatically : change manually by using [CH
K / L]
Note:
• “No Signal” will appear on the TV screen after the minor channel broadcast is over.
EN
minor channel
Still Mode
5
You can freeze the image shown on the TV screen.
Switching Each Mode
5
You can easily switch with the remote control to the DTV (ATSC) and TV (NTSC) or to access an external device when they are connected to the unit.
INTRODUCTION
Press
[STILL] to pause the image shown on the screen.
Still
The sound output will not be paused.
• If no signal is detected or protected signal is received
• during still mode, the image remains paused and the sound output will be muted. The still function will be released after 5 minutes.
To cancel still mode, press any button except [POWER].
Press [INPUT SELECT] or [CH K] repeatedly to cycle through the input modes.
TV/DTV channel
Video1
or
Pressing [CH L] reverses the direction of the mode.
• To use the video or S-video input jack of VIDEO 1 on
Video2
Component1
Component2
HDMI1
HDMI2
PC
the unit, select “Video1”. To use the video or S-video input jack of VIDEO 2 on
• the unit, select “Video2”. To use the component video input jack of
• COMPONENT 1 on the unit, select “Component1”. To use the component video input jack of
• COMPONENT 2 on the unit, select “Component2”. To use the HDMI 1-IN jack on the unit, select
• “HDMI1”. To use the HDMI 2-IN jack on the unit, select
• “HDMI2”. To use the PC-IN jack on the unit, select “PC”.
CONNECTION INITIAL SETTING OPTIONAL SETTING
WATCHING TV
TROUBLESHOOTING
17
EN
INFORMATION
ATCHING TV
W
Switching Audio Mode
5
This section describes how to switch the audio language.
TV
DTV
Press [AUDIO] to display the currently selected
1
audio mode. While receiving an MTS broadcast, press repeatedly to cycle through the available audio channel.
6
When all audio are available
When stereo and monaural audio are available
When SAP and monaural audio are available
When only monaural audio is available
STEREO : Outputs stereo-audio SAP : Outputs second audio program MONO : Outputs mono-audio
SAP / STEREO SAP / MONO
SAP / STEREO
MONO / STEREO MONO / STEREO
SAP / MONO SAP / MONO
(Cannot be switched)
SAP / STEREO
MONO
Press [AUDIO] to display the currently selected
1
language and the number of available languages.
6-1
Press [AUDIO] repeatedly to cycle through the
2
available audio languages.
Available languages differ depending on the
• broadcast. “Other” is displayed when the audio language cannot be acquired, or the acquired languages are other than English, Spanish or French. The current mode will automatically disappear in a
• few seconds.
English 1/3 Spanish 2/3
English 1/3
Other 3/3
Note:
• Pressing [AUDIO] does not control external audio device.
18
The current mode will automatically disappear in a
• few seconds.
EN
Screen Information
6-1
English 1/2
TV-PG DLSV
1080i
1080i
16:9
16:9HDHD
CC
CC
A Day of Memories
A Day of Memories
KABC
KABC
A quarter-century ago,which may now qualify as the good old days of newspapering,run-of-paper sales accounted for 80 percent of the industry's advertising revenues.Department stores and supermarket were
1
24
39
5
6, 7, 8
10
5
You can display the currently selected channel or other information such as the audio mode on the TV screen.
TV
In the analog mode, the current channel number and the audio mode are displayed.
DTV
In the digital mode, the detailed broadcasting information for the current channel such as program title, program guides are displayed.
INTRODUCTION
CONNECTION INITIAL SETTING OPTIONAL SETTING
Press [INFO].
6
SAP / STEREO
480i
480i
The current channel number, audio mode, type of
• resolutions for video signal, TV aspect ratio, CC and TV rating are displayed at the top-right corner of the TV screen. To clear the display, press [INFO] again. You can also press [BACK].
SD
SD
TV-PG DLSV
4:3
4:3
CC
CC
Press [INFO] to display the details of the currently selected program.
[Broadcasting Information]
The following information is displayed.
1 program title 2 broadcast station 3 program guide
(The program guide added to broadcasting information is displayed. Maximum display of 4 lines.)
4 channel number 5 audio language
(Refer to “Switching Audio Mode” on page 18.)
6 effective scanning lines and scan mode 7 program format 8 program aspect ratio 9 program rating 10 CC (not available if CC is set to “Off”)
WATCHING TV
TROUBLESHOOTING
Note:
• When the program guide consists of more than 4 lines, use [Cursor K/ L] to scroll.
• “No description provided” is displayed when the program guide is not provided.
• While the program guide is displayed, the closed caption function is interrupted.
• In external input mode, the following screen is displayed; e.g.) When an external device is connected to VIDEO 1
input jack.
Video1
480iSDSD
480i
TV-PG DLSV
• The information display will automatically disappear in 1 minute.
CC
CC
INFORMATION
19
EN
ATCHING TV
W
TV Screen Display Mode
5
4 types of display modes can be selected when the broadcasting station is sending 4:3 or 16:9 video signal. And 3 types of display modes can be selected for PC input signal.
Press [SCREEN MODE] repeatedly to switch the TV aspect ratio.
For 4:3 video signal
Sidebar
(normal)
Wide
[Sidebar]
Display a 4:3 picture at its original size. Sidebars appear on both edges of the screen.
[Full]
Display a 4:3 picture at a 16:9 size; the picture is stretched horizontally to fill the screen.
[Cinema]
Display a 4:3 picture at a 16:9 size; the picture is stretched horizontally and vertically to fill the screen. This crops out the top and bottom of the picture.
[Wide]
Display the picture with its center at the original size and the edges stretched horizontally.
Full
Cinema
For 16:9 video signal
Full
(normal)
Expand Cinema
[Full]
Display a 16:9 picture at its original size.
[Zoom]
Display a 16:9 picture at its maximum size without changing its horizontal and vertical ratio.
[Cinema]
Display a vertically stretched picture.
[Expand]
Display a horizontally stretched picture.
For PC input signal
Sidebar Full
Zoom
20
Dot By Dot
(normal)
[Sidebar]
Display a proportionately stretched picture. Sidebars appear on both edges of the screen.
[Full]
Display a picture that is stretched out of proportion to fill the screen.
[Dot By Dot]
Display a picture in its original size.
Note:
• You may not switch the display mode depending on the program.
• For PC input signal, “Sidebar” may not be selectable depending on the aspect ratio of the input signal.
EN
Sleep Timer
5
The sleep timer can be set to automatically turn off the unit after an incremental period of time.
INTRODUCTION
Press [SLEEP] to set the sleep timer.
1
Sleep timer display appears on the TV screen.
Press [SLEEP] repeatedly to change the amount of time
2
until shut off.
You can set your unit to turn off after a set period of
• time (from 30 to 120 minutes). Each press of [SLEEP] will increase the time by 30
• minutes. After set up, the sleep timer display can be called up
• for checking by pressing [SLEEP].
To Cancel the Sleep Timer
Press [SLEEP] repeatedly until “Sleep Off” is displayed on the TV screen.
Sleep
Sleep
Off
120min.
Note:
• The sleep timer setting display will automatically disappear in a few seconds.
• When you disconnect the unit from the AC outlet or when a power failure occurs, the sleep timer setting will be canceled.
CONNECTION INITIAL SETTING OPTIONAL SETTING
WATCHING TV
TROUBLESHOOTING
21
EN
INFORMATION
PTIONAL SETTING
O
5
Channel List
The channel list function lets you remove undesired channels from the channel registration list.
Press [SETUP] to display the main menu.
1
Use [Cursor K / L] to select “CHANNEL”, then press
2
[ENTER].
Use [Cursor K / L] to select “Channel List”, then press
3
[ENTER].
Channel
Channel
Autoscan Channel List Manual Register Antenna
Press [SETUP] to exit.
5
Use [Cursor K / L] to select the channel you want to
4
remove, then press [ENTER].
Channel List
Channel List
Highlight channels for Ch Up/Down key selection.
ENTER
Ch Select Watch/Skip Back
The channel display for the removed channel
• darkens. You will not be able to select the channel again using [CH K / L]. To reactivate a removed channel, highlight it using
[Cursor K / L] and press [ENTER]. The channel display lightens. When you remove a major channel, its minor
• channels are removed as well.
Note:
• The channel with the “DTV” indicated on the display is ATSC. Otherwise the channel is NTSC.
DTV 6
DTV 6
DTV 8
DTV 8
DTV 48
DTV 48
DTV 67
BACK
27
9
9
58
58
22
EN
Manual Register
5 Antenna Confirmation
The manual register function lets you add the channels that were not added
5
This function lets you check the signal strength of each channel.
by the auto channel scan due to the reception condition at the initial setting.
Press [SETUP] to display the main menu.
1
Use [Cursor K / L] to select “CHANNEL”, then press
2
[ENTER].
Use [Cursor K / L] to select “Manual Register”, then
3
press [ENTER].
Channel
Channel
Autoscan Channel List Manual Register Antenna
Use [the Number buttons] to enter the number of the
4
channel you want to add, then press [ENTER].
Press [SETUP] to display the main menu.
1
Use [Cursor K / L] to select “CHANNEL”, then press
2
[ENTER].
Use [Cursor K / L] to select “Antenna”, then press
3
[ENTER].
Channel
Channel
Autoscan Channel List Manual Register Antenna
Use [the Number buttons] or [CH K / L] to select the
4
channel for which you want to check the signal strength.
WATCHING TVINTRODUCTION CONNECTION INITIAL SETTING
OPTIONAL SETTING
TROUBLESHOOTING
Manual Register
Manual Register
For analog channels, select a channel to register using number keys. For digital channels, you must perform Autoscan function.
Ch Change
Press [SETUP] to exit.
5
Note:
• If set up completes successfully, “Registered to the Channel List” is displayed.
• If external input is used, it is not possible to register the channel and “Unavailable” will be displayed on the TV screen.
11
Register
BACK
Back
Antenna
Antenna
Now 0 0 Peak
CH
Ch Change
11
Back
INFORMATION
If the channel is set to external input, you cannot
• confirm the antenna condition.
Video1
Antenna
Press [SETUP] to exit.
5
Antenna
Indicator is available for antenna signal only.
CH
Ch Change
Back
23
EN
PTIONAL SETTING
O
Picture Adjustment
5
You can adjust brightness, contrast, color, tint and sharpness.
Press [SETUP] to display the main menu.
1
Use [Cursor K / L] to select “PICTURE”, then press
2
[ENTER].
Use [Cursor K / L] to select the item you want to adjust,
3
then press [ENTER].
Picture
Picture
Picture Mode Brightness Contrast Color Tint Sharpness Reset Settings Color Temp. Energy Saving
Adjust the picture quality.
4
Dynamic
Neutral
Cursor
Brightness
Brightness 30
Adjust
Contrast
Contrast
Adjust Move
Color
Color
Adjust Move
s
to decrease
ENTER
Move
Enter
60
36
ENTER
Enter
ENTER
Enter
brightness
to decrease contrast
to decrease color
Cursor
to increase brightness
to increase contrast
to brighten color
B
Tint
Tint
0
Adjust Move
ENTER
Enter
to add red to add green
Sharpness
0Sharpness
Adjust Move
ENTER
Enter
to make soft to make clear
Reset Settings
Use [Cursor K / L] to select “Reset”, then press [ENTER] to restore the “Picture Mode” setting to default.
Reset Settings
Reset Settings
This function resets the "Dynamic" setting for Picture Mode
30 60 36
0 0
Off
to factory default.
Cancel Reset
Color Temp.
Use [Cursor K / L] to select the desired setting, then press [ENTER]. (Cool, Neutral and Warm)
Picture Mode
Use [Cursor K / L] to select the desired setting, then press [ENTER]. (Standard, Dynamic, Movie and News)
Picture
Picture
Picture Mode
Brightness Contrast Color Tint Sharpness Reset Settings Color Temp. Energy Saving
Brightness, Contrast, Color, Tint, Sharpness
s / B
Use [Cursor
] to adjust.
24
EN
Standard
Dynamic
Movie News
Energy Saving Use [Cursor
/
s
B
] to adjust the brightness of the backlight.
: To brighten
Energy Saving Off
: To darken
Note:
• To cancel picture adjustment, press [SETUP].
Press [SETUP] to exit.
5
Adjust
Picture
Picture
Picture Mode Brightness Contrast Color Tint Sharpness Reset Settings
Color Temp.
Energy Saving
Cool
Neutral
Warm
ENTER
Enter
Loading...
+ 56 hidden pages