Sylvania LC320SS9, LC320SS9 A, LC320SS9 B User Manual

LC320SS9 B LC320SS9 A LC320SS9

NEED HELP?

PLEASE CALL TOLL FREE!

1-800-968-3429

OR VISIT OUR WEB SITE AT

www.sylvania-ce.com

Owner’s Manual

WATCHING TVINTRODUCTION PREPARATION INITIAL SETTING OPTIONAL SETTING

HIGH-DEFINITION TELEVISION

TO RECEIVE DIGITAL/ANALOG SIGNAL, YOU MUST CONNECT ANTENNA.

TROUBLESHOOTING

INFORMATION

NTRODUCTION

The model and serial numbers of this unit may be found on the cabinet. You should record and retain those numbers for future reference.

Model No.:

Serial No.:

Precautions5

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS

TO RAIN OR MOISTURE.

APPARATUS SHALL NOT BE EXPOSED TO DRIPPING OR SPLASHING AND NO OBJECTS

FILLED WITH LIQUIDS, SUCH AS VASES, SHALL BE PLACED ON THE APPARATUS.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

The caution marking is located on the rear or bottom of the cabinet.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the apparatus’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the apparatus.

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacture’s instructions.

8. Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

Do not place the unit on the furniture that is capable of being tilted by a child and an adult leaning, pulling, standing or climbing on it. A falling unit can cause serious injury or even death.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the

manufacturer.

12. Use only with the cart, stand, tripod, bracket,

or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when

unused for long periods of time.

14. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

FCC WARNING

This apparatus may generate or use radio frequency energy. Changes or modifications to this apparatus may cause harmful interference unless the modifications are expressly approved in the manual. The user could lose the authority to operate this apparatus if an unauthorized change or modification is made.

RADIO-TV INTERFERENCE

This apparatus has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This apparatus generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this apparatus does cause harmful interference to radio or television reception, which can be determined by turning the apparatus off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1) Reorient or relocate the receiving antenna.

2) Increase the separation between the apparatus and receiver.

3) Connect the apparatus into an outlet on a circuit different from that to which the receiver is connected.

4) Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

This apparatus should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided. Make sure to leave a space of 3.2 inches (8cm) or more around this apparatus.

Disconnect the mains plug to shut off when find trouble or not in use. The mains plug shall remain readily operable.

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. WARNING: Batteries (battery pack or battery installed) shall not be exposed to excessive heat such as sunshine, fire or the like.

LAMP IN LCD CONTAINS MERCURY, DISPOSE ACCORDING TO LOCAL, STATE OR FEDERAL LAW.

WARNING: To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the instructions.

TO AVOID THE HAZARDS OF ELECTRICAL SHOCK AND FIRE

Do not handle the power cord with wet hands.

• Do not remove this unit cabinet. Touching parts inside the cabinet could result in electric shock and/or damage to this

• unit. For service and adjustment inside the cabinet, call a qualified dealer or an authorized service center. Do not pull on the power cord when disconnecting it from an AC outlet. Grasp it by the plug.

• Do not put your fingers or objects into the unit.

•

LOCATION AND HANDLING

The openings should not be blocked by placing the unit on a bed, sofa, carpet, rug, or other similar surface.

• Do not install the unit near or over a radiator or heat register.

• Do not install the unit in direct sunlight, near strong magnetic fields, or in a place subject to dust or strong vibration.

• Avoid a place with drastic temperature changes.

• Install the unit in a horizontal and stable position. Do not place anything directly on top or bottom of the unit.

• Depending on your external devices, noise or disturbance of the picture and/or sound may be generated if the unit is placed too close to them. In this case, please ensure enough space between the external devices and the unit. Depending on the environment, the temperature of this unit may increase slightly. This is not a malfunction.

•

NOTE ABOUT RECYCLING

This unit’s packaging materials are recyclable and can be reused. Please dispose of any materials in accordance

• with your local recycling regulations. Batteries should never be thrown away or incinerated but disposed of in accordance with your local

• regulations concerning chemical wastes.

WHEN CARRYING THIS UNIT

At least two people are required when carrying this unit.

• Make sure to hold the upper and bottom frames of the unit firmly as illustrated.

•

INTRODUCTION

PREPARATION

INITIAL SETTING

WATCHING TV INFORMATION

OPTIONAL SETTING TROUBLESHOOTING

Supplied Accessories5

owner’s manual (1EMN23599)

If you need to replace these accessories, please refer to the part No. with the illustrations and call our toll free

• customer support line found on the cover of this manual. Depending on your antenna system, you may need different types of combiners (mixers) or separators (splitters).

• Contact your local electronics store for these items.

quick start guide (1EMN22859)

remote control (NF015UD)

batteries (AA x 2)

Phillips pan screw for attaching the stand x 3 (FPH34100)

NTRODUCTION

Attaching the Stand

You must attach the stand to the unit to display upright. Be sure the front and rear of the stand match the proper direction.

Spread a thick and soft cloth over a

table. Place the main unit face down onto it. Make sure not to damage the screen. At least two people are required at this step.

Insert the stand all the way to the

main unit slowly until it clicks. Make sure not to put the AC cord between the stand and the unit.

Drive Phillips pan screws in the 3

threaded holes at the bottom of the stand with a screwdriver tightly.

screw holes

lever

To Remove the Stand from this Unit

Unscrew the Phillips pan screws indicated by “1”, then lift the lever on the bottom stand and remove the stand from the unit slowly. Be careful not to drop the stand when you remove it.

Note:

• When attaching the stand, ensure that all screws are tightly fastened. If the stand is not properly attached, it could cause the unit to fall, resulting in injuries as well as damage to the unit.

• Make sure to use a table which can support the weight of this unit and is larger than this unit.

• Make sure the table is in a stable location.

Symbols Used in this Manual

The following is the description for the symbols used in this manual. Description refers to:

: Digital TV operation

DTV

If neither symbol appears under the function heading, operation is applicable to both.

•

Trademark Information

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI

• Licensing LLC.

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby

• Laboratories.

Products that have earned ENERGY STAR® are designed to protect the environment through superior energy efficiency.

•

: Analog TV operation

INTRODUCTION

Features5

•

DTV/TV/CATV

You can use your remote control to select channels which are broadcast in digital format and conventional analog format. Also, cable subscribers can access their cable TV channels.

•

Information Display (DTV only)

You can display the title, contents and other information of the current DTV program on the TV screen.

•

Auto Channel Scan

This unit automatically scans and memorizes channels available in your area, eliminating difficult setup procedures.

•

V-chip

This feature allows you to block children’s access to inappropriate programs.

•

Closed Caption Decoder

Built-in closed caption decoder displays text for closed caption supported programs.

•

MTS/SAP Tuner

Audio can be selected from the remote control.

•

Auto Shut Off Function

If there is no signal input from the antenna terminal and no operation for 15 minutes, the unit will turn off automatically.

•

Sleep Timer

This feature will automatically turned off the power of the unit at a specific time.

•

Choices for On-screen Language

Select your on-screen language: English, Spanish or French.

•

Stereo Sound Function

•

PLL Frequency Synthesized Tuning

Provides free and easy channel selection and lets you tune directly to any channel using the channel number buttons on the remote control.

•

HDMI Input

•

PC Input

•

Component Video Input

•

S-video Input

•

AV Input

•

Digital Audio Coaxial Output

Contents5

INTRODUCTION

Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Attaching the Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Symbols Used in this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Trademark Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Buttons on the Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Installing the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

PREPARATION

Basic Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

External Device Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

INITIAL SETTING

Initial Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Main Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Auto Channel Scan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Language Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

WATCHING TV

Channel Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Sleep Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Still Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Switching Each Input Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Switching Audio Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Screen Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

TV Screen Display Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

OPTIONAL SETTING

Channel List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Manual Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Antenna Confirmation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Picture Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Sound Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Closed Caption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

DTV Closed Caption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

CC Style . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

V-chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

PC Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

HDMI Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

TROUBLESHOOTING

Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

FAQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

INFORMATION

Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Cable Channel Designations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Electrical Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Other Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back cover

any storage medium, in any form or for any purpose without the express prior written consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.

Information in this document is subject to change without notice. Funai reserves the right to change the content herein without the obligation to notify any person or organization of such changes.

with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way without the express written consent of Funai. All other trademarks used herein remain the exclusive property of their respective owners. Nothing contained in this manual should be construed as granting, by implication or otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law.

PREPARATION

INITIAL SETTING

WATCHING TV INFORMATION

OPTIONAL SETTING TROUBLESHOOTING

NTRODUCTION

Buttons on the Remote Control5

CH RETURN

1. POWER (p13)

Press to turn the unit on and off.

2. Number buttons (p16)

•

Press to select channels.

- (hyphen)

Press to shift the minor channel

• from the major channel.

3. SETUP (p14)

Press to display the main menu.

4. s / B / K / L (p13)

Press to move left/ right/ up/ down through the items.

5. ENTER (p13)

Press to decide the command of setting when the main menu is displayed.

6. BACK (p18)

Press to return to the previous menu operation.

7. CH RETURN (p16)

Press to return to the previously viewed channel.

8. VOL. X / Y (p16)

Press to adjust the volume.

9. MUTE (p16)

Press to turn the sound on and off.

10. INPUT SELECT (p17)

Press to access connected external devices like a DVD player or VCR.

11. SLEEP (p16)

Press to activate the sleep timer.

12. AUDIO (p17)

Digital Mode (DTV)

Press to select the audio

• language.

Analog Mode (TV)

Press to select the audio mode.

•

13. STILL (p17)

Press to pause screen image.

14. SCREEN MODE (p19)

Press to select aspect ratio available for the TV screen.

15. INFO (p18)

Digital Mode (DTV)

Press to display the channel

• information, signal type and TV setting.

Analog Mode (TV)

Press to display the channel

• number, signal type and TV setting.

External Input Mode

Press to display the external

• input modes, signal type and TV setting.

16. CH K / L (p16)

Press to select channels and the external input modes.

Installing the Batteries

Install the batteries (AA x 2) matching the polarity indicated inside battery compartment of the remote control.

Battery Precautions:

• Be sure to follow the correct polarity as indicated in the battery compartment. Reversed batteries may cause damage to the device.

• Do not mix different types of batteries together (e.g., Alkaline and Carbon-Zinc) or old batteries with fresh ones.

• If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.

• Do not try to recharge batteries; they can overheat and rupture.

INTRODUCTION

Control Panel5

Rear Panel5

rear of this unit

5 6

DIGITAL AUDIO OUT (COAXIAL)

PC-IN

AUDIO

HDMI-IN

AUDIO

rear of this unit

VIDEO 1

S-VIDEO

VIDEO

AUDIO

side of this unit

rear of this unit

COMPONENT 1 COMPONENT 2

AUDIO

1. POWER (p13)

Press to turn the unit on and off.

2. INPUT SELECT/ENTER (p17)

Press to access connected external devices like a

• DVD player or VCR. Press to decide the command of setting when the

• menu is displayed.

3. CHANNEL K / L (p16)

Press to select channels or move up/down through the

main menu items.

4. VOLUME X / Y (p16)

Press to adjust the volume or move right (X) / left (Y) through the main menu items.

5. SETUP (p14)

6 7 8

Press to display the main menu.

6. infrared sensor window

Receives infrared rays transmitted from the remote control.

7. power on indicator

Lights up when power is on.

8. stand by indicator

Lights up in standby mode.

1. PC input jack (p12)

VGA cable connection for PC.

2. HDMI input jack (p9)

HDMI connection for HDMI devices.

3. AC power cord

Connect to a standard AC outlet to supply power to this unit.

4. coaxial digital audio output jack (p11)

Coaxial digital audio connection for a decoder or an audio receiver.

5. S-video input jack (p10)

S-video connection for external devices.

6. video input jack (p11)

RCA video connection for external devices.

7. audio input jack for PC connection (p12)

Mini-plug audio cable connection for PC.

8. audio input jack (p9)

RCA audio connection for DVI devices. (For HDMI1 input jack only)

9. audio input jack (p10)

RCA audio connection for external devices.

10. component video and audio input jack (p10)

RCA component video and RCA audio connection for

external devices.

11. antenna input jack (p8)

RF coaxial cable connection for your antenna or cable/satellite box.

PREPARATION

INITIAL SETTING

WATCHING TV INFORMATION

OPTIONAL SETTING TROUBLESHOOTING

side of this unit

REPARATION

Cables not included.

Please purchase the necessary cables at your local store.

Basic Connection

This section describes how to connect the unit to an antenna, cable/satellite box, etc.

Note:

• Be sure your antenna or other device is connected properly before plugging in the power cord.

[Antenna Connection]

Connect the RF coaxial cable on your home outlet to the antenna input jack of this unit.

e.g.)

VHF / UHF antenna

RF coaxial cable

cable TV

company

Once connections are completed, turn on the unit and begin initial setup.

Channel scanning is necessary for the unit to memorize all available channels in your area. (Refer to “Initial Setup” on page 13.)

rear of this unit

Note:

• For your safety and to avoid damage to this unit, please unplug the RF coaxial cable from the antenna input jack before moving the unit.

• If you use an antenna to receive analog TV, it should also work for DTV reception. Outdoor or attic antennas will be more effective than settop versions.

• To switch your reception source easily between antenna and cable, install an antenna selector.

• If you connect to the cable system directly, contact the CATV installer.

[Connection to Cable Box or Satellite Box]

Use an RF coaxial cable to connect the antenna input jack of the unit to the antenna output jack of the cable/satellite box.

e.g.)

satellite dish

ANT OUTANT IN

cable TV

company

cable/satellite box

Required cables and connecting methods differ depending on the cable/satellite box. For more information, please contact your cable/satellite provider.

STEREO PCM

RF coaxial cable

rear of this unit

Cables not included.

Please purchase the necessary cables at your local store.

External Device Connection

[HDMI Connection]

HDMI (High-Definition Multimedia Interface) transports high definition video and multi-channel digital audio through a single cable. It ensures that the content sent from the source to the unit is of the highest possible resolution. Use an HDMI cable to connect the unit to external video devices equipped with HDMI output jack.

e.g.)

rear of this unit

PREPARATION

INITIAL SETTING

HDMI cable

TITLE 5 CHAPTER 15 REPEAT A-B

HDMI OUT

DVD player with the HDMI output jack

Note:

• This unit accepts 480i / 480p / 720p / 1080i video signals, and 32kHz / 44.1kHz / 48kHz audio signals.

• This unit accepts only 2 channel audio signal (LPCM).

• You need to select “PCM” for the digital audio output of the device connected or the check HDMI audio setting. There may be no audio output if you select “Bitstream”, etc.

• This unit only accepts signals compliant with EIA861.

[HDMI-DVI Connection]

Use an HDMI-DVI conversion cable to connect the unit to external video devices equipped with DVI output jack.

e.g.)

STEREO PCM

cable box or satellite box with the DVI output jack

DVI OUT

AUDIO OUT

HDMI-DVI conversion cable

To HDMI1 input jack only

rear of this unit

WATCHING TVINTRODUCTION

OPTIONAL SETTING

TROUBLESHOOTING

INFORMATION

RCA audio cable

Note:

• This unit accepts 480i / 480p / 720p / 1080i video signals.

• HDMI-DVI connection requires separate RCA audio connection as well.

• Audio signals are converted from digital to analog for this connection.

• DVI does not display 480i image that is not compliant with EIA/CEA-861/861B.

HDMI-IN

AUDIO

REPARATION

Cables not included.

Please purchase the necessary cables at your local store.

[Component Video Connection]

RCA component video connection offers better picture quality for video devices connected to the unit. Use an RCA component video cable to connect the unit to external video devices equipped with component video output jacks. If you connect to the unit’s COMPONENT1 or COMPONENT2 video input jacks, connect an RCA audio cable to the audio L/R jacks of COMPONENT1 or COMPONENT2 accordingly.

e.g.)

TITLE 5 CHAPTER 15 REPEAT A-B

DVD player with the component video output jacks

RCA component video cable

(red)(blue)(green)

COMPONENT VIDEO OUT

AUDIO OUT

Pr/CrPb/CbY

RCA audio cable

green

blue

red

DIGITAL AUDIO OUT (COAXIAL)

PC-IN

AUDIO

HDMI-IN

AUDIO

rear of this unit

COMPONENT 1 COMPONENT 2

VIDEO 1

S-VIDEO

VIDEO

AUDIO

Note:

• This unit accepts 480i / 480p / 720p / 1080i video signals.

• When the noise appears on the TV screen, disconnecting the VGA cable may reduce it.

[S-video Connection]

S-video connection offers good picture quality for video devices connected to the unit. Use an S-video cable to connect the unit to external video devices equipped with S-video output jack. If you connect to the unit’s VIDEO1 S-video or VIDEO2 S-video input jack, connect an RCA audio cable to the audio L/R jacks of VIDEO1 or VIDEO2 accordingly.

e.g.)

S-VIDEO

OUT

TITLE 5 CHAPTER 15 REPEAT A-B

AUDIO OUT

AUDIO

DVD player with the S-video output jack

S-video cable

RCA audio cable

Note:

• If you connect to the S-video input jack and the video input jack at the same time, the S-video connection will have priority.

rear of this unit

DIGITAL

VIDEO 1

AUDIO OUT (COAXIAL)

S-VIDEO

PC-IN

VIDEO

AUDIO

HDMI-IN

AUDIO

Cables not included.

Please purchase the necessary cables at your local store.

[Video Connection]

RCA video connection offers standard picture quality for video devices connected to the unit. Use an RCA video cable to connect the unit to external video devices equipped with video output jack. If you connect to the unit’s VIDEO1 or VIDEO2 video input jack, connect an RCA audio cable to the audio L/R jacks of VIDEO 1 or VIDEO 2 accordingly. When the audio jack of the video device is monaural, connect an RCA audio cable to the audio L input jack.

e.g.)

camcorder video game

STEREO

STAND-BY

VCR

AUDIO OUT

VIDEO

OUT

rear of this unit

RCA video cable

RCA audio cable

Note:

• If you connect to the S-video input jack and the video input jack at the same time, the S-video connection will have priority.

[Audio Output Connection]

AUDIO OUT

(COAXIAL)

HDMI-IN

PREPARATION

INITIAL SETTING

DIGITAL

VIDEO 1

S-VIDEO

PC-IN

VIDEO

AUDIO

WATCHING TVINTRODUCTION

OPTIONAL SETTING

À Digital (for digital broadcasting only)

If you connect this unit to an external digital audio device, you can enjoy multi-channel audio like 5.1ch digital broadcasting sound. Use a digital audio coaxial cable to connect the unit to external digital audio devices.

e.g.)

Dolby Digital

decoder

DIGITAL AUDIO

COAXIAL IN

digital audio coaxial cable

rear of this unit

AUDIO OUT

(COAXIAL)

HDMI-IN

TROUBLESHOOTING

INFORMATION

DIGITAL

VIDEO 1

S-VIDEO

PC-IN

VIDEO

AUDIO

REPARATION

Cables not included.

Please purchase the necessary cables at your local store.

[PC Connection]

This unit is equipped with a PC input jack. If you connect this unit to your PC, you can use this unit as a computer monitor.

e.g.)

personal computer

VGA cable should be with ferrite core.

VGA cable

mini-plug audio cable

The following signals can be displayed:

Format Resolution V. Frequency

SVGA 800 x 600 60Hz XGA 1024 x 768 60Hz WXGA 1280 x 768 60Hz WXGA 1360 x 768 60Hz

Other formats or non-standard signals will not be displayed correctly.

Note:

• Please purchase the VGA cable that has a ferrite core.

• The following operations may reduce noise.

- Attach a ferrite core to the AC power cord of your PC.

- Unplug the AC power cord and use the built-in battery of your PC.

PC-IN

AUDIO

HDMI-IN

AUDIO

rear of this unit

NITIAL SETTING

These operations are accessible by remote control. Some may also be accessible by controls on the main unit.

Initial Setup

This section will guide you through the unit’s initial setting which includes selecting a language for your on-screen menu and auto channel scan, which automatically scans and memorizes viewable channels.

Before you begin:

Make sure if the unit is connected to antenna or cables.

After making all the necessary connections, press

[POWER] to turn on the unit.

This operation may take a few moments.

•

Use [Cursor K / L] to select the on-screen language

from the choices on the right side of the TV screen. (English / Español / Français)

Initial Setup

Select the language for setup display.

Elija el idioma de ajuste.

Sélectionner langue écran config.

ENTER

Select Enter Exit

•

“Initial Setup” menu on step 3 will be displayed in the selected language after you press [ENTER].

English

Español

Français

SETUP

Note:

• If you connect the cable system directly, contact the CATV installer.

• If you press [POWER] or [SETUP] during auto channel scan, this setting will be canceled.

• The initial auto channel scan function can be executed for either “Air” or “Cable” only once. When you change the connection (Air/Cable), set auto channel scan again. (Refer to page 14.)

• You can cancel or exit the initial auto channel scan menu by pressing [SETUP].

• If there is no signal input from the antenna terminal and no operation for several seconds after you turn on the unit, “Helpful Hints” appears. Follow the instructions listed on the TV screen.

2-2

No channel is registered. Press and hold "ENTER" key on the remote control for 3 seconds. Contact support hotline provided on manual or back of unit.

Sin canal registrado. Pulse durante 3 segundos la tecla "ENTER" en el control remoto. Llame teléfono de apoyo en manual o atrás de TV.

Pas de chaîne consign. Enfoncez "ENTER" 3 secondes sur la télécommande. Contacter numero d'urgence dans manuel ou arrière appareil.

INITIAL SETTING

WATCHING TVINTRODUCTION PREPARATION

OPTIONAL SETTING

TROUBLESHOOTING

Use [Cursor K / L] to select “Air” for TV channels or

“Cable” for CATV channels, then press [ENTER].

Initial Setup

Make sure the antenna is connected to "ANT.IN" jack. Select the destination of "ANT.IN" jack.

Air

Cable

BACK

ENTER

Select Enter Exit

Back

•

Scanning and memorizing of channels start automatically.

Initial Setup

Now the system is scanning for channels,please wait.

Analog channels 1ch

Digital channels 0ch

When the scanning and memorizing of channels are

• completed, the lowest memorized channel will be displayed.

ANT.IN

Air Cable

INFORMATION

SETUP

Exit

NITIAL SETTING

Main Menu

5 Auto Channel Scan

This section describes the overview of the main menu displayed when you press [SETUP]. For more details, see the reference page for each item. The main menu consists of the function setting items below.

If you switch wires (e.g., between antenna and CATV) or if you move the unit to a different area after the initial setting, or if you restore the DTV channel you deleted, you will need to perform auto channel scan.

Before you begin:

Make sure if the unit is connected to antenna or cables.

Press [SETUP].

EXIT

To exit settings.

PICTURE

You can adjust the picture quality. (Refer to “Picture Adjustment” on page 22.)

SOUND

You can adjust the sound quality. (Refer to “Sound Adjustment” on page 23.)

CHANNEL

You can automatically scan the viewable channels and remove the undesired channels. (Refer to “Auto Channel Scan” on page 14.)

DETAIL

You can change the display format for closed caption, which displays the dialogue of a TV program or other information across the TV screen. (Refer to “Closed Caption” on page 24.) You can set the viewing limitations. (Refer to “V-chip” on page 28.) You can adjust the position, stability and clarity of the PC screen. (Refer to “PC Settings” on page 31.) You can select the sound input for the HDMI1 input jack if your unit is connected to an HDMI or DVI device. (Refer to “HDMI Audio” on page 32.)

LANGUAGE

You can change the language (English, Spanish, French) displayed on the main menu. (Refer to “Language Selection” on page 15.)

Press [SETUP] to display the main menu.

Use [Cursor K / L] to select “CHANNEL” , then press

[ENTER].

Use [Cursor K / L] to select “Autoscan”, then press

[ENTER].

Use [Cursor K / L] to select an appropriate option, then press [ENTER].

When aerial antenna is connected, select “Air”.

• When connected to CATV, select “Cable”.

•

Scanning and memorizing of channels start automatically.

Channel

Autoscan Channel List Manual Register Antenna

Autoscan

Autoscan will rescan all channels. This may take a while to complete.

Select the destination of "ANT.IN" jack.

Air

Cable

ANT.IN

Back Air Cable Cable

1 hour

Now the system is scanning for channels, please wait.

72%

Analog channels 10ch

When the scanning and memorizing are completed,

•

Digital channels 6ch

SETUP

Exit

the lowest memorized channel will be displayed.

Note:

• After setting “Auto Channel Scan”, using [CH K / L] on the remote control skips unavailable programs automatically.

• If you connect the cable system directly, contact the CATV installer.

• If you press [POWER] or [SETUP] during auto channel scan, the setting will be canceled.

• Channel settings will be saved even if the power fails.

• If you need the English menus instead of the Spanish or French menus you are having, press [SETUP]. Use

[Cursor K [ENTER]. Use [Cursor K / L] to select “English”, then press [ENTER]. Press [SETUP] to exit the main menu.

• With regard only to the digital channel, even after the scanning is completed if you unplug the AC power cord before turning off the unit by pressing [POWER], the channel setting may be lost.

/ L] to select “IDIOMA” or “LANGUE”, then press

Language Selection

You can choose English, Spanish, or French as your on-screen language.

Press [SETUP] to display the main menu.

Use [Cursor K / L] to select “LANGUAGE”, then press

[ENTER].

INITIAL SETTING

WATCHING TVINTRODUCTION PREPARATION

Use [Cursor K / L] to select “English”, “Español” or

“Français”, then press [ENTER].

Language

Select the language for setup display.

Elija el idioma de ajuste.

Sélectionner langue écran config.

Press [SETUP] to exit.

OPTIONAL SETTING

English

Español

Français

TROUBLESHOOTING

INFORMATION

ATCHING TV

Channel Selection

Select channels by pressing [CH

K /

] or [the Number buttons].

Volume Adjustment

This section describes how to adjust the volume. The mute function, which turns the sound off and on, is also described.

To select the memorized channels, use [CH

•

[the Number buttons]. To select the non-memorized channels, use

•

[the Number buttons].

To Use [the Number buttons]

When selecting analog channel 12

DTV

When selecting digital channel 12-1

Be sure to press [–] before entering the minor channel number.

Press [CH RETURN] to return to the previously

• viewed channel.

About digital TV broadcasting:

With its high definition broadcast, digital broadcasting far surpasses analog broadcasting in both its picture and sound quality.

What is the minor channel?

By using high compression technology, digital broadcasting offers a service that enables multiple signals to send simultaneously. Therefore, you can select more than one program per major channel since digital broadcasting technology distinguishes between multiple channels broadcast by a single network.

NTSC (analog mode)

CH4

: change automatically : change manually by using [CH

[Air Time]

18:00

18:30

19:00

19:30

20:00

20:30

major channel

ATSC (digital mode)

No signal

CH4

(high definition TV)

CH4

CH4-1

CH4

No signal

CH4

CH4-1

K / L]

Note:

• “No Signal” will appear on the TV screen after the minor channel broadcast is over.

• “Audio only program“ message will appear on the TV screen, when you receive only sound signal.

L] or

No signal

CH4

No signal

CH4-2

minor channel

Use [VOL.

The volume bar will be displayed at the bottom of

• the TV screen when adjusting the volume. The volume bar will automatically disappear in a few

• seconds.

Press [MUTE ] to turn off and on the sound.

“Mute” is displayed on the TV screen for a few

• seconds.

Press [MUTE original volume.

Sleep Timer

The sleep timer can be set to automatically turn off the unit after an incremental period of time.

Press [SLEEP] to set the sleep timer.

Sleep timer display appears on the TV screen.

•

Press [SLEEP] repeatedly to change the amount of time

until shut off.

You can set your unit to turn off after a set period of

• time (from 30 to 120 minutes). Each press of [SLEEP] will increase the time by 30

• minutes. After setup, the sleep timer display can be called up

• for checking by pressing [SLEEP].

] to adjust the audio volume.

Volume 20

Mute

] again or [VOL.

Sleep

] to recover the

Off

120min.

To Cancel the Sleep Timer

Press [SLEEP] repeatedly until “Sleep Off” is displayed on the TV screen.

Note:

• The sleep timer display will automatically disappear in a few seconds.

• When you disconnect the unit from the AC outlet or when a power failure occurs, the sleep timer setting will be canceled.

Still Mode

You can pause the image shown on the TV screen.

Switching Audio Mode

This section describes how to switch the audio in the analog mode and how to switch the audio language in the digital mode.

INTRODUCTION

Press

You can easily switch with the remote control to the DTV (ATSC) and TV (NTSC) or to access external devices when they are connected to the unit.

[STILL] to pause the image shown on the TV

screen.

Still

The sound output will not be paused.

• If no signal is detected or protected signal is received

• during still mode, the image remains paused and the sound output will be muted. The still function will be released after 5 minutes.

•

To cancel still mode, press any button except [POWER].

Switching Each Input Mode

Press [INPUT SELECT] or [CH K] repeatedly to cycle through the input modes.

DTV/TV channel

Video1

Video2

Component1

Component2

HDMI1

HDMI2

Pressing [CH L] reverses the direction of the input

• modes. To use the video or S-video input jack of VIDEO1 on

• the unit, select “Video1”. To use the video or S-video input jack of VIDEO2 on

• the unit, select “Video2”. To use the component video input jacks of

• COMPONENT1 on the unit, select “Component1”. To use the component video input jacks of

• COMPONENT2 on the unit, select “Component2”. To use the HDMI1 input jack on the unit, select

• “HDMI1”. To use the HDMI2 input jack on the unit, select

• “HDMI2”. To use the PC input jack on the unit, select “PC”.

•

Press [AUDIO] to display the currently selected

audio mode. While receiving an MTS broadcast, press repeatedly to cycle through the available audio channel.

When all audio are available

When stereo and monaural audio are available

When SAP and monaural audio are available

When only monaural audio is available

STEREO : Outputs stereo-audio SAP : Outputs second audio program MONO : Outputs mono-audio

DTV

Press [AUDIO] to display the currently selected

language and the number of available languages.

Press [AUDIO] repeatedly to cycle through the

available audio languages.

Available languages differ depending on the

• broadcast. “Other” is displayed when the audio language cannot be acquired, or the acquired languages are other than English, Spanish or French.

SAP / STEREO SAP / MONO

SAP / STEREO

MONO / STEREO MONO / STEREO

SAP / MONO SAP / MONO

(Cannot be switched)

SAP / STEREO

MONO

6-1

English 1/3

Note:

• Pressing [AUDIO] does not control external audio devices.

• The information display will automatically disappear in a few seconds.

PREPARATION INITIAL SETTING OPTIONAL SETTING

WATCHING TV

TROUBLESHOOTING

INFORMATION

ATCHING TV

6-1

English 1/2

TV-PG DLSV

1080i

16:9

16:9HDHD

A Day of Memories

KABC

A quarter-century ago,which may now qualify as the good old days of newspapering,run-of-paper sales accounted for 80 percent of the industry's advertising revenues.Department stores and supermarket were

6, 7, 8

Screen Information

You can display the currently selected channel or other information such as the audio mode on the TV screen.

In the analog mode, the current channel number and the audio mode are displayed.

DTV

In the digital mode, the detailed broadcasting information for the current channel such as program title, program guides are displayed.

Press [INFO].

SAP / STEREO

480i

The current channel number, audio mode, type of

• resolutions for video signal, TV aspect ratio, CC and TV program rating are displayed on the top-right corner of the TV screen. To clear the display, press [INFO] again. You can also press [BACK].

TV-PG DLSV

4:3

Press [INFO] to display the details of the currently selected program.

Broadcasting Information

The following information is displayed.

•

1 program title 2 broadcast station 3 program guide

(The program guide added to broadcasting information is displayed. Maximum display of 4 lines.)

4 channel number 5 audio language

(Refer to “Switching Audio Mode” on page 17.)

6 effective scanning lines and scan mode 7 program format 8 program aspect ratio 9 program rating 10 CC (not available if CC is set to “Off”)

Note:

• When the program guide consists of more than 4 lines, use [Cursor K/ L] to scroll.

• “No description provided.” is displayed when the program guide is not provided.

• While the program guide is displayed, the closed caption function is interrupted.

• In external input mode, the following screen is displayed; e.g.) When an external device is connected to VIDEO1 input

jack.

Video1

480iSDSD

480i

TV-PG DLSV

• The information display will automatically disappear in 1 minute.

TV Screen Display Mode

4 types of display modes can be selected when the broadcasting station is sending 4:3 or 16:9 video signal. And 3 types of display modes can be selected for PC input signal.

Press [SCREEN MODE ] repeatedly to switch the TV aspect ratio.

INTRODUCTION

PREPARATION INITIAL SETTING OPTIONAL SETTING

For 16:9 video signal

For 4:3 video signal

Sidebar

(normal)

Wide

Full

Cinema

Sidebar

Display a 4:3 picture at its original size. Sidebars appear on both edges of the screen.

Full

Display a 4:3 picture at a 16:9 size; the picture is stretched horizontally to fill the screen.

Cinema

Display a 4:3 picture at a 16:9 size; the picture is stretched horizontally and vertically to fill the screen. This crops out the top and bottom of the picture.

Wide

Display the picture with its center at the original size and the edges stretched horizontally.

Full

(normal)

Expand

Zoom

Cinema

Full

Display a 16:9 picture at its original size.

Zoom

Display a 16:9 picture at its maximum size without changing its horizontal and vertical ratio.

Cinema

Display a vertically stretched picture.

Expand

Display a horizontally stretched picture.

For PC input signal

Sidebar Full

WATCHING TV

TROUBLESHOOTING

INFORMATION

Dot By Dot

(normal)

Sidebar

Display a proportionately stretched picture. Sidebars appear on both edges of the screen.

Full

Display a picture that is stretched out of proportion to fill the screen.

Dot By Dot

Display a picture in its original size.

Note:

• You may not switch the display mode depending on the program.

• For PC input signal, “Sidebar” may not be selectable depending on the aspect ratio of the input signal.

PTIONAL SETTING

Channel List

The channel list function lets you remove undesired channels from the channel registration list.

Manual Register

The manual register function lets you add the channels that were not added by the auto channel scan due to the reception condition at the initial setting.

Press [SETUP] to display the main menu.

Use [Cursor K / L] to select “CHANNEL”, then press

[ENTER].

Use [Cursor K / L] to select “Channel List”, then press

[ENTER].

Channel

Autoscan Channel List Manual Register Antenna

Use [Cursor K / L] to select the channel you want to

remove, then press [ENTER].

Press [SETUP] to display the main menu.

Use [Cursor K / L] to select “CHANNEL”, then press

[ENTER].

Use [Cursor K / L] to select “Manual Register”, then

press [ENTER].

Channel

Autoscan Channel List Manual Register Antenna

Use [the Number buttons] to enter the number of the

channel you want to add, then press [ENTER].

The channel display for the removed channel

• darkens. You will not be able to select the channel again using [CH K / L]. To reactivate a removed channel, use [Cursor K / L] and

• press [ENTER]. The registered channels are highlighted. When you remove a major channel, its minor

• channels are removed as well.

Note:

• The channel with the “DTV” indicated on the display is ATSC. Otherwise the channel is NTSC.

Press [SETUP] to exit.

Channel List

Highlight channels for Ch Up/Down key selection.

ENTER

Ch Select Watch/Skip Back

DTV 6

DTV 8

DTV 48

DTV 67

BACK

Manual Register

For analog channels, select a channel to register using number keys. For digital channels, you must perform Autoscan function.

Ch Chan

BACK

Back

Press [SETUP] to exit.

Note:

• If set up completes successfully, “Registered to the channel list” is displayed.

• If external input is used, it is not possible to register the channel and “Unavailable” will be displayed on the TV screen.

Antenna Confirmation

Antenna

Back

Ch Chan

Indicator is available for digital broadcasting only.

DTV

This function lets you check the digital signal strength of each channel.

Press [SETUP] to display the main menu.

Use [Cursor K / L] to select “CHANNEL”, then press

[ENTER].

Use [Cursor K / L] to select “Antenna”, then press

[ENTER].

Channel

Autoscan Channel List Manual Register Antenna

Use [the Number buttons] or [CH K / L] to select the

channel for which you want to check the digital signal strength.

Antenna

Now 70 80 Peak

If the channel is set to analog channel or external

• input, you cannot confirm the antenna condition.

Ch Chan

WATCHING TVINTRODUCTION PREPARATION INITIAL SETTING

OPTIONAL SETTING

TROUBLESHOOTING

11-1

Back

INFORMATION

Press [SETUP] to exit.

PTIONAL SETTING

Picture Adjustment

You can adjust brightness, contrast, color, tint and sharpness.

Press [SETUP] to display the main menu.

Use [Cursor K / L] to select “PICTURE”, then press

[ENTER].

Use [Cursor K / L] to select the item you want to adjust,

then press [ENTER].

Picture

Picture Mode Brightness Contrast Color Tint Sharpness Reset Settings Color Temp. Energy Saving

Adjust the picture quality.

Picture Mode

Use [Cursor K / L] to select the desired setting, then press [ENTER]. (Standard, Dynamic, Movie and News)

Picture

Picture Mode

Brightness Contrast Color Tint Sharpness Reset Settings Color Temp. Energy Saving

Dynamic

Neutral

Standard

Dynamic

Movie News

Cursor

Brightness

Brightness 30

Adjust

Contrast

Adjust Move

Color

Adjust Move

to decrease

ENTER

Move

Enter

ENTER

Enter

ENTER

Enter

brightness

to decrease contrast

to decrease color

Cursor

to increase brightness

to increase contrast

to brighten color

Tint

Adjust Move

ENTER

Enter

to add red to add green

Sharpness

0Sharpness

Adjust Move

ENTER

Enter

to make soft to make clear

Reset Settings

Use [Cursor K / L] to select “Reset”, then press [ENTER] to restore the “Picture Mode” settings to the default.

Reset Settings

30 30 30

0 0

Off

Reset Settings

This function resets the "Dynamic" setting for Picture Mode to factory default.

Cancel Reset

Color Temp.

Use [Cursor K / L] to select the desired setting, then press [ENTER]. (Cool, Neutral and Warm)

Picture

Picture Mode Brightness Contrast Color Tint Sharpness Reset Settings

Color Temp.

Energy Saving

Cool

Neutral

Warm

Energy Saving

Use [Cursor

] to adjust the brightness of the backlight.

Brightness, Contrast, Color, Tint, Sharpness

Use [Cursor

] to adjust.

: To brighten

Energy Saving Off

Adjust

: To darken

Press [SETUP] to exit.

Note:

• To cancel picture adjustment, press [SETUP].

• When this unit is connected to PC or DVI devices, you cannot select “Sharpness”.

ENTER

Enter

Sound Adjustment

You can adjust treble and bass.

Press [SETUP] to display the main menu.

Use [Cursor K / L] to select “SOUND”, then press

[ENTER].

Reset Settings

Use [Cursor K / L] to select “Reset”, then press [ENTER] to restore the sound settings to the default.

Reset Settings

This function resets the Sound settings to factory default.

Press [SETUP] to exit.

Cancel Reset

Use [Cursor K / L] to select the sound type you want to

adjust, then press [ENTER].

Sound

Treble Bass Reset Settings

Adjust the sound setting.

Treble, Bass

Use [Cursor s / B] to adjust.

Cursor

Treble

Bass

Adjust

Move

ENTER

Enter

ENTER

Enter

to decrease higher-pitched sounds

to decrease lower-pitched sounds

to increase higher-pitched sounds

to increase lower-pitched sounds

Note:

WATCHING TVINTRODUCTION PREPARATION INITIAL SETTING

• To cancel sound adjustment, press [SETUP].

0 0

OPTIONAL SETTING

TROUBLESHOOTING

INFORMATION

+ 53 hidden pages